| - SUMMARY OF THIS ACTION
- FEDERAL ACTIONS CONSIDERED IN THIS RULEMAKING
- R08-5: Wastewater Pretreatment Update, USEPA Amendments
- January 1, 2007 through June 30, 2007
- R08-7: SDWA Update, USEPA Amendments
- January 1, 2007 through June 30, 2007
- March 12, 2007 (at 72 Fed. Reg. 11200)
- R08-13: SDWA Update, USEPA Amendments July 1, 2007 through December 31, 2007
- October 10, 2007 (at 71 Fed. Reg. 65574)
- Later SDWA (Drinking Water) Amendments of Interest
- June 3, 2008 (at 73 Fed. Reg. 31616)
- No Other Federal Actions Having a Direct Impact on the
- Illinois SDWA (Drinking Water) Regulations
- TIMETABLE FOR COMPLETION OF THIS RULEMAKING AND
- EXTENSION OF THE DEADLINE FOR FINAL ACTION
- PUBLIC COMMENTS
- DISCUSSION
- Discussions of the Federal Actions
- General Revisions and Deviations from the Federal Text
- Discussion of Corrective Amendments
- Tabulation of Miscellaneous Housekeeping Amendments
- Table 1:
- Deviations from the Text of the Federal Amendments
- Table2:
- Board Housekeeping Amendments
|
ILLINOIS POLLUTION CONTROL BOARD
August 7, 2008
IN THE MATTER OF:
)
WASTEWATER PRETREATMENT
UPDATE, USEPA AMENDMENTS (January
1, 2007 though June 30, 2007)
)
)
)
)
R08-5
(Identical-in-Substance
Rulemaking - Public Water Supply)
)
SDWA UPDATE, USEPA AMENDMENTS
(January 1, 2007 though June 30, 2007 and
June 3, 2008)
)
)
)
R08-7
(Identical-in-Substance
Rulemaking - Public Water Supply)
)
SDWA UPDATE, USEPA AMENDMENTS
(July 1, 2007 though December 31, 2007)
)
)
)
R08-13
(Identical-in-Substance
Rulemaking - Public Water Supply)
)
(Consolidated)
Proposed Rule. Proposal for Public Comment. Deadline Extension.
OPINION OF THE BOARD (by T.E. Johnson):
SUMMARY OF THIS ACTION
The Board today proposes amendments to the Illinois regulations that are “identical in
substance” to wastewater pretreatment and drinking water regulations adopted by the United
States Environmental Protection Agency (USEPA). The amendments involved in this
consolidated docket incorporate into the Illinois wastewater pretreatment and drinking water
regulations amendments in response to two USEPA actions. Those actions span the two
identical-in-substance update periods of January 1, 2007 through June 30, 2007 and July 1, 2007
through December 31, 2007. The Board has added a third set of USEPA amendments that
occurred later than these periods. The added later amendments are closely related to
amendments that occurred during the January 1, 2007 through June 30, 2007 time period.
The Board further finds that more time is necessary to complete these amendments and
extends the deadline for final action by this order. The deadline is extended from August 15,
2008 until December 1, 2008 pursuant to Section 7.2(b) of the Environmental Protection Act
(Act), 415 ILCS 5/7.2(b) (2006). The reasons for the extension is discussed below on page 5 of
this opinion.
This is the second extension of the deadline. By an order dated March 6, 2006, the Board
found that an extension of the deadline for final adoption of these amendments was necessary.
That order extended the deadline from March 12, 2008 until August 15, 2008.
The R08-5 docket includes federal wastewater pretreatment amendments that USEPA
adopted in the period January 1, 2007 though June 30, 2007. On March 12, 2007, USEPA
2
adopted amendments relating to analytical methods approved under the wastewater pretreatment
and drinking water programs. The R08-5 docket includes the wastewater pretreatment segments
of those amendments.
The R08-7 docket includes federal Safe Drinking Water Act (SDWA) amendments that
USEPA adopted in the period January 1, 2007 though June 30, 2007, and on June 3, 2008. On
March 12, 2007, USEPA adopted amendments relating to analytical methods approved under the
wastewater pretreatment and drinking water programs. The R08-5 docket includes the drinking
water segments of those amendments. On June 3, 2008, USEPA approved alternative methods
for analysis under the drinking water program. The Board has added the June 3, 2008
amendments to the R08-5 docket due to their close relationship with the March 12, 2007
amendments.
The R08-13 docket includes federal SDWA amendments that USEPA adopted in the
period July 1, 2007 though December 31, 2007. On October 10, 2007, USEPA revised segments
of the Lead and Copper Rule under the drinking water regulations.
Sections 7.2 and 13.3 of the Act (415 ILCS 5/7.2 and 13.3 (2006)) require the Board to
adopt regulations that are “identical in substance” to federal wastewater pretreatment
regulations. The USEPA wastewater pretreatment rules implement Sections 307(b), (c), and (d)
and 402(b)(8) and (b)(9) of the Federal Water Pollution Control Act (FWPCA) (33 U.S.C.
§§ 1317(b), (c), and (d) and 1342(b)(8) and (b)(9) (2006)). The federal wastewater pretreatment
regulations are found at 40 C.F.R. 400 through 499. Section 13.3 also provides that Title VII of
the Act and Section 5 of the Administrative Procedure Act (APA) (5 ILCS 100/5-35 and 5-40
(2006)) do not apply to the Board’s adoption of identical-in-substance regulations.
Sections 7.2 and 17.5 of the Act (415 ILCS 5/7.2 and 17.5 (2006)) provide for quick
adoption by the Board of regulations that are identical in substance to federal regulations that
USEPA adopts to implement Sections 1412(b), 1414(c), 1417(a), and 1445(a) of the federal
SDWA (42 U.S.C. §§ 300g-1(a), 300g-3(c), 300g-6(a), and 300j-4(a) (2006)). The USEPA
National Primary Drinking Water Regulations (NPDWRs) implement Sections 1412(b), 1414(c),
1417(a), and 1445(a) of the federal SDWA (42 U.S.C. §§ 300g-1(a), 300g-3(c), 300g-6(a), and
300j-4(a) (2006)). The federal SDWA regulations are found at 40 C.F.R. 141 through 143.
Section 17.5 also provides that Title VII of the Act and Section 5 of the APA (5 ILCS 100/5-35
and 5-40 (2006)) do not apply to the Board’s adoption of identical-in-substance regulations.
The Board will cause the proposed amendments to be published in the
Illinois Register
and will hold the docket open to receive public comments for 45 days after the date of
publication. The Board will then adopt and file the final rules, taking into account the public
comments received. The Board specifically requests comment on two aspects of the rules:
location of particular analytical methods approved by USEPA and Agency approval of the
content of public education materials.
The Board presently expects that rules will be adopted and filed no later than December
1, 2008, pursuant to the extension of the deadline adopted by the Board pursuant to Section
7.2(b) of the Act (415 ILCS 5/7.2(b) (2006)) in this order.
3
This opinion supports an order that the Board also adopts today.
FEDERAL ACTIONS CONSIDERED IN THIS RULEMAKING
This docket includes federal SDWA amendments that USEPA adopted in two
consecutive time periods: January 1, 2007 though June 30, 2007 and July 1, 2007 though
December 31, 2007. USEPA adopted one set of amendments during the two periods that
affected the wastewater pretreatment regulations and the SDWA primary drinking water
regulations. A second set of amendments adopted in the two periods amended the SDWA rules
alone. A third set of amendments that the Board has included occurred outside these two
periods. That third set is closely related to amendments already included in this consolidated
docket. The following briefly summarizes the three principal federal actions that are considered
in this rulemaking, including four corrections to them:
R08-5: Wastewater Pretreatment Update, USEPA Amendments
January 1, 2007 through June 30, 2007
R08-7: SDWA Update, USEPA Amendments
January 1, 2007 through June 30, 2007
March 12, 2007 (at 72 Fed. Reg. 11200)
USEPA modified the testing procedures approved for sampling and analysis in programs
established under the Clean Water Act (CWA) and the SDWA. The wastewater pretreatment
rules are established under CWA, and the Primary Drinking Water Regulations are established
under SDWA. The amendments updated the versions allowed for existing methods and
approved new methods for use. The drinking water aspects of these amendments relate closely
to later amendments adopted by USEPA on June 3, 2008. A brief description of the June 3, 2008
action appears below on page 4 of this opinion.
R08-13: SDWA Update, USEPA Amendments July 1, 2007 through December 31, 2007
October 10, 2007 (at 71 Fed. Reg. 65574)
USEPA amended the lead and copper rule to strengthen its implementation in the areas of
monitoring, treatment processes, public education, customer awareness, and lead service line
replacement. The federal amendments were effective on December 10, 2007. Compliance by
regulated entities is due no later than December 10, 2009.
Later SDWA (Drinking Water) Amendments of Interest
The Board engages in ongoing monitoring of federal actions. As of the date of this
opinion and accompanying order, the Board has identified one set of related USEPA actions
since December 31, 2007 that further amend the SDWA rules in a way that affects the present
amendments. The following describes those amendments in brief:
4
June 3, 2008 (at 73 Fed. Reg. 31616)
USEPA approved 99 alternative test methods for analysis of contaminants in drinking
water. This was USEPA’s first use of a new summary approval mechanism. Section 1401(1) of
SDWA (42 U.S.C. § 300f(1) (2006)) authorizes USEPA to approve alternative methods by
guidance published in a
Federal Register
notice without the formalities of a full rulemaking
action. USEPA listed the methods in a new appendix to 40 C.F.R. 141.
When the Board observes an action outside the nominal timeframe of a docket that
requires expedited consideration, the Board will expedite consideration of those amendments in
the pending docket. Federal actions that could warrant expedited consideration include those
that directly affect the amendments involved in this docket, those for which compelling reasons
would warrant consideration as soon as possible, and those for which the Board has received a
request for expedited consideration.
The Board has included the June 3, 2008 USEPA action in docket R08-7 because most of
the methods involved in that action affect the same segments of the Illinois rules that are
involved in the March 12, 2007 amendments. Further, many of the alterative methods approved
in the June 3, 2008 action are the same version of the methods as are involved in the March 12,
2007 amendments, but they are now available in a printed volume, rather than from an on-line
source in an electronic format.
If the Board identifies any federal action that fulfills these criteria prior to final action on
the present amendments, the Board may include those amendments in the present consolidated
docket R08-5/R08-7/R08-13 upon final adoption.
No Other Federal Actions Having a Direct Impact on the
Illinois SDWA (Drinking Water) Regulations
In addition to the amendments to the federal wastewater pretreatment and SDWA
regulations, amendments to certain other federal regulations occasionally have an effect on the
Illinois drinking water rules. Most notably, 35 Ill. Adm. Code 611.102 includes the
incorporation of 40 C.F.R. 136.3(a) and Appendix B to 40 C.F.R. 136 of by reference. These are
federal CWA methods for analysis of contaminants in water. 35 Ill. Adm. Code 310.110
similarly incorporates several segments of the federal regulations by reference, including 40
C.F.R. 3.3, 3.10, 3.2000, 25, tables II and II in appendix D to part 122, 136, 403 (generally),
403.12, appendices D and G to part 403, and 503. 35 Ill. Adm. Code 307.2201 incorporates 40
C.F.R. 122.23(b) and (c) by reference, and 35 Ill. Adm. Code 310.602 incorporates 40 C.F.R.
403.12(b) by reference.
As of December 31, 2007, the ending date of the federal actions involved in this proposal
for public comment, USEPA had not amended any of these federal regulations. No Board action
will be required at this time to update the versions of these documents incorporated by reference
in any of Parts 307, 310, or 611.
5
TIMETABLE FOR COMPLETION OF THIS RULEMAKING AND
EXTENSION OF THE DEADLINE FOR FINAL ACTION
Under Section 7.2 of the Act (415 ILCS 5/7.2(b) (2004)), the Board must complete this
rulemaking within one year of the date of the earliest set of federal amendments considered in
this docket. USEPA adopted the earliest federal amendments that required Board attention on
March 12, 2007, so that the deadline for Board adoption of these amendments under that
provision was March 12, 2008.
Section 7.2(b), however, further provides for extension of the deadline for final Board
action by adoption of a Board order and publication of a Notice of Public Information on
Proposed Rules that extends the deadline. By an order dated March 6, 2008, the Board used this
provision to extend the deadline. Delays in finalizing the voluminous hazardous waste
amendments involved in RCRA Subtitle C Update, USEPA Amendments (March 5, 2005,
September 8, 2005, January 1, 2006 through June 30, 2006), R07-5 and RCRA Subtitle C
Update, USEPA Amendments (July 1, 2006 through December 31, 2006), R07-14 (June 5, 2008)
delayed development of this proposal for public comment. This was compounded by the volume
and complexity of the present amendments. These are the principal factors that make an
extension of the deadline for final action in this matter necessary. The Board today again
extends the deadline for completion of this proceeding.
The final Board action to adopt these amendments is now December 1, 2008. This
extended deadline has a slight amount of extra time added to allow for any minor unforeseen
delays in finalizing the amendments.
Considering the proposal of these amendments on this date, the Board presently projects
the following will occur in the progress towards completion of these amendments:
Extended Due date (by a March 6, 2008 order):
August 15, 2008
Date of Board vote to propose amendments:
August 7, 2008
Submission for
Illinois Register
publication:
August 18, 2008
Probable
Illinois Register
publication dates:
August 29, 2008
Estimated end of 45-day public comment period:
October 13, 2008
Likely date of Board vote to adopt amendments:
November 6, 2008
Probable filing and effective date:
November 17, 2008
Probable
Illinois Register
publication date:
November 26, 2008
PUBLIC COMMENTS
The Board will receive public comments on this proposal for 45 days following its
publication in the
Illinois Register
. After that time, the Board will immediately consider
adoption of the amendments, making any necessary changes made evident through the public
comments. The Board expects to file any adopted rules with the Secretary of State immediately
after adoption, but no later than December 1, 2008.
6
As of this date, the Board has received one series of e-mail communications and a second
responsive e-mail, both of which bore attachments, that have been introduced into the docket as
public comments. These are described as follows:
PC 1 E-mail to Michael J. McCambridge, Board Hearing Officer, from Jayne Brown,
Waters Chemistry Tech Support, Waters Corp., dated July 8, 2008, with
attachment, “Dissolved Inorganic Anions in Aqueous Matrices by Capillary Ion
Electrophoresis.”
PC 2 E-mail exchange between Michael J. McCambridge, Board Hearing Officer, and
Pat Fair, Technical Support Center, Office of Ground Water and Drinking Water,
USEPA, between July 8, 2008 and July 10, 2008, with attachment, “Test Method
for Determination of Dissolved Inorganic Anions in Aqueous Matrices Using
Capillary Ion Electrophoresis and Chromate Electrolyte.”
DISCUSSION
The following discussion begins with a description of the amendments undertaken in
direct response to the federal action involved in this proceeding. The discussion closes with a
description of the miscellaneous amendments that are not directly derived from the federal
action, but which the Board routinely includes in these update dockets as necessary.
Discussions of the Federal Actions
Analytical Methods Update--Sections 307.4000, 307.7500, 310.107, 611.102, 611.526,
611.531, 611.600, 611.611, 611.612, 611.645, and 611.720
The USEPA action of March 12, 2007 (72 Fed. Reg. 11200) amended the provisions that
prescribe the analytical methods that a regulated entity must use to demonstrate compliance
under the federal CWA (33 U.S.C. §§ 1251
et. seq.
(2006)) and the federal SDWA (42 U.S.C.
§§ 300f
et seq.
(2006)). Among the provisions that USEPA amended were 40 C.F.R. 136.3,
136.4, 136.5, 136.6, 430.02, 455.50, Table 7 to 455, and 465.03, which set forth the methods for
use under CWA programs, and 40 C.F.R. 141.21, 141.23, 141.24, 141.25, 141.74, 143.4, which
set forth analytical methods for use under SDWA. Of the SDWA-related analytical provisions,
all the amendments relate to the NPDWRs except 40 C.F.R. 143.4, which relates to the National
Secondary Drinking Water Regulations. The amendments designate new methods as acceptable,
and they add updated versions of older methods as acceptable.
On June 3, 2008, USEPA used a new mechanism for approval of methods. Prior to that
action, USEPA approved and updated methods only by rulemaking. Under 1996 amendments to
Section 1401(1) of SDWA (42 U.S.C. § 300f(1) (2006);
see
Pub. L. 104-182, Sec. 101(a)(1)(B),
110 Stat. 1613, 1616 (Aug. 6, 1996)), USEPA can use a summary procedure for approving or
updating methods that are equivalent to methods that it has already approved by rulemaking.
This provision allows the approval and update of methods by guidelines published in the
Federal
Register
.
See
42 U.S.C. § 300f(1) (2006) (definition of “National Primary Drinking Water
Regulation”). USEPA chose to incorporate the guidelines directly into the NPDWRs by addition
7
of an appendix A to 40 C.F.R. 141. Many of the methods approved as equivalent by USEPA in
new appendix A are actually hard-copy published versions of methods previously only available
online in a digital format.
The Board updated the methods in the Illinois wastewater pretreatment and drinking
water regulations to correspond with the March 12, 2007 USEPA methods approval and update
and the June 3, 2008 USEPA designation of alternative methods. The Board has undertaken to
incorporate the federal changes as near in substance as possible, but has found it necessary to
deviate from the federal changes in some regards. Any person interested in the substance of the
USEPA actions should review the
Federal Register
notices of March 12, 2007 and June 3, 2008.
The following discussion only reviews the substance of the federal actions to the degree
necessary to incorporate the substance of the federal changes into the Illinois regulations.
Incorporation of the changes into the wastewater pretreatment rules involved updating
the version of the appropriate provisions from the
Code of Federal Regulations
that is
incorporated by reference in the Illinois provision. Updating the methods provisions in the
Illinois drinking water rules presented a small measure of difficulty, since the methods are
actually set forth in the Illinois rules.
The first area of difficulty with the amendments related to USEPA’s references to
methods available only in an electronic format. In the interests of rule clarity for the public as a
whole, the Board prefers to reference printed documents where those are available.
In its March 12, 2007 action, USEPA updated a number of methods from the standard
reference,
Standard Methods for the Examination of Water and Wastewater
(
Standard Methods
)
to a more recent version of each method as available from Standard Methods Online
(www.standardmethods.org/store/), a website maintained by the Standard Methods
Organization.
1
The latest edition of the printed version of
Standard Methods
that USEPA cited
in the March 12, 2007 action was the 20th edition, published in 1998. The Standard Methods
Organization published the 21st edition of
Standard Methods
in 2005. Upon review of the
version dates of the methods cited by USEPA as available from Standard Methods Online, the
1
The Standard Methods Organization is a partnership of the American Water Works Association
(AWWA), the American Public Health Association (APHA), and the Water Environment
Federation. In Section 611.102, the Board cites the Standard Methods Organization members,
AWWA and APHA, as the sources of the printed version of the methods. The latest version and
the latest USEPA-approved version of each method is available for purchase in an electronic
(PDF) format from Standard Methods Online, as is the latest printed version of
Standard
Methods
. At some future time, with the advent of Standard Methods Online shifting the focus to
the Standard Methods Organization as the source of the methods, it may be more accurate for the
Board to amend Section 611.102 to cite the Standard Methods Organization as the source of both
electronic and printed versions of
Standard Methods
. The Board has not included such a change
in this proposal for public comment, but could include such changes in the adopted rules should
public comments in this docket strongly support the Board doing so. Otherwise, the Board might
include a proposal to make such changes in a future rulemaking proceeding.
8
Board noted that the version date of each of those methods was the same in the printed 21st
edition of
Standard Methods
. The Board cited to the
Standard Methods
21st edition, rather than
to the on-line version for each of those methods.
2
By the June 3, 2008 action, USEPA added the version of each method that appears in the
printed 21st edition of
Standard Methods
.
3
This supports the Board’s determination to cite to
the printed volume of the 21st edition for the methods. The Board did not cite to Standard
Methods Online for any of the methods cited by USEPA in its March 12, 2006 action.
4
The
Board added Board notes at each citation to a method from the 21st edition that explains that
USEPA cited to Standard Methods Online and the Board chose not to do so.
On June 3, 2008, however, USEPA did incorporate two methods from Standard Methods
Online that do not yet appear in any printed version of
Standard Methods
. These are the 2004
versions of Method 6610 B and Method 9230 B that the Standard Methods Organization did not
included in the 2005 printing of the
Standard Methods
21st edition. The Board did cite to
Standard Methods Online for those two methods.
The second area of difficulty related to two other new methods that the Board has had
difficulty locating, which has meant that the Board has struggled to obtain acceptable copies of
the methods. USEPA cites the first method as available from the Environmental Resources
Center, Georgia Institute of Technology, and it cites to the second method as available from the
Waters Corporation.
2
These methods included Method 2130, Method 2320, Method 2510, Method 2550, Method
3111, Method 3112, Method 3113, Method 3114, Method 3120, Method 3500-Ca, Method 3500-
Mg, Method 4110, Method 4500-CN
-
, Method 4500-F
-
, Method 4500-H
+
, Method 4500-NO
2
-
,
Method 4500-NO
3
-
, Method 4500-P, Method 4500-SiO
2
, Method 7110, Method 7120, Method
7500-Cs, Method 7500-
3
H, Method 7500-I, Method 7500-Ra, Method 7500-Sr, Method 7500-U.
Methods from Standard Methods Online that USEPA had previously approved on January 4,
2006 (at 71 Fed. Reg. 388) which also appeared in the 21st edition of the printed version
included Method 2130, Method 4500-Cl, Method 4500-ClO
2
, Method 4500-O
3
, Method 4500-I,
Method 5310, Method 6251, Method 9215, Method 9221, Method 9222, and Method 9223. The
Board adopted those federal amendments by reference to the printed volume of the 21st edition
in SDWA Update, USEPA Amendments (January 1, 2006 though June 30, 2006), R07-2, and
SDWA Update, USEPA Amendments (July 1, 2006 though December 31, 2006), R07-11 (July
26, 2007).
3
USEPA did add the 1999 version of Method 4500-P from Standard Methods Online, even
though this version of the method also appears in the printed 21st edition of
Standard Methods
,
which USEPA also cited.
4
This includes the methods previously adopted by USEPA on January 4, 2006 and by the Board
on July 26, 2007.
See infra
note 2.
9
Section 5-75 of the APA (5 ILCS 100/5-75 (2006)) requires that the Board fulfill certain
requirements to incorporate any document by reference. Two are of primary interest here. First,
the Board must provide the name and address of the source of the document, that an interested
person might obtain a copy. Second, the Board must maintain a copy of the document in one
principal office open for public review. 5 ILCS 100/5-75(a) and (c) (2006).
The difficulties encountered with the analytical methods from Georgia Institute of
Technology and Waters Corporation that USEPA approved on March 12, 2007 present problems
in this regard. The Board’s continued inability to sufficiently locate the methods and obtain
copies is serious enough that the Board may not be able to adopt the present amendment and
include those two methods.
The first method is entitled “The Determination of Radium-226 and Radium-228 in
Drinking Water by Gamma-ray Spectrometry Using HPGE or Ge(Li) Detectors,” Revision 1.2,
December 2004. It is a method for Radium-226 and Radium-228 by gamma ray spectrometry. It
allows analysis for both parameters with a single test, rather than requiring two separate
analyses. It was cited by USEPA as from the Environmental Resources Center at the Georgia
Institute of Technology. The Board could not locate the Environmental Resources Center.
However, the Board did find references to the method, and research disclosed that another entity
called the Water Resources Center at the Georgia Institute for Technology might be a successor
organization. The same person who ran the Environmental Resources Center heads the Water
Resources Center. Attempts to contact either entity have proven fruitless to date. Thus, the
Board can neither obtain the method nor accurately cite to the source of this method. The
inability to do either would preclude incorporation of this method by reference. Attempts to
obtain a copy of this method from USEPA have also proven fruitless to date.
The Board has included the method from the Environmental Resources Center in this
proposal for public comment, and the proposal lists the method as available from that source,
even though it is apparent that that entity no longer exists—at least under that name. The
method will be removed from the rules upon final adoption of these amendments if the Board
cannot obtain a copy of the method.
The Board has also had difficulty locating the second method, cited by USEPA as
available from the Waters Corporation, but for different reasons. The federal amendments to 40
C.F.R. 141.23(k)(1) add method “D6508, Rev. 2,” noting that it is entitled “Test Method for
Determination of Dissolved Inorganic Anions in Aqueous Matrices Using Capillary Ion
Electrophoresis and Chromate Electrolyte,” and that it is available from the Waters Corporation.
Attempts to obtain a useable method from the Waters Corporation, however, proved fruitless.
5
USEPA sent a copy of the method from its rulemaking docket. That copy bore at its top a date
and method designation in annotations that indicated USEPA’s review and approval of the
5
The Waters Corporation sent a method number 6500, entitled “Dissolved Inorganic Anions in
Aqueous Matrices by Capillary Ion Electrophoresis,” which on examination is actually the 2007
version of Method 6500 from “Test Methods for Evaluating Solid Waste, Physical/Chemical
Methods,” familiarly known as “SW-846.”
See
PC 1.
10
method. Those annotations indicate that the method is ASTM Method D6508, revision 2, dated
December 2000. Examination of ASTM methods indicates that the latest version of ASTM
Method D6508 is revision 2, dated 2005. ASTM designates this method as “ASTM D6508-
00(2005)e2” by ASTM, with “00” designating that the method was approved in 2000, and
“(2005)e2” indicating revision 2 made in 2005. This 2005 revision appears to be the same as the
method designated by USEPA as Waters Method D6508, revision 2.
The Board has included ASTM Method D6508-00(2005)e2 in place of what USEPA has
called Waters Method D6508, revision 2 in this proposal for public comment. It is worthy of
note, however, that USEPA has cautioned that it has not yet determined that the ASTM method
is equivalent to the Waters method. A determination by USEPA that the Board included a
method that is not approved by USEPA would result in USEPA’s disapproval of the Illinois
rules. USEPA has suggested that the Board’s decision not to include Waters Method D6508,
revision 2 would present no problems. PC 2.
A final area that warrants specific discussion in this segment of the opinion relates to the
USEPA-approved alternative methods. USEPA used a limited, summary procedure to adopt the
list of equivalent methods. June 3, 2008 was USEPA’s first use of that procedure. While
USEPA approved all prior methods by rulemaking, USEPA is authorized to approve equivalent
methods by this summary procedure. While the Board can perceive a difference between a
determination that a method is adequate for use and a determination that another method is an
equivalent to a method that is approved for use, the Board believes that this is a distinction
without a difference from the perspective of a person seeking guidance from the regulations as to
how to comply with the requirements. For this reason, the Board chose to include the alternative
methods together with the approved methods in the text of the rules. The Board did not add an
equivalent to appendix A. Thus, the listing of methods approved for use for analysis of any
particular chemical species appears together in a single listing.
The tables that appear beginning on page 20 of this opinion list and briefly describe the
deviations from the literal text of the federal rules and the changes made in the existing text of
the Illinois rules that were not derived from federal amendments. The Board requests public
comment on the incorporation of the March 12, 2007 USEPA CWA and SDWA methods
revisions and the June 3, 2008 approval of alternative drinking water methods into the Illinois
wastewater pretreatment and drinking water regulations. In particular, the Board requests
comments on the proposed handling of specific analytical methods, as follows:
1.
Is there any reason the Board should include references to Standard Methods
Online, where the same version of the Standard Method is available in the printed
21st edition of
Standard Methods
, considering that a Board note appended to the
incorporation of
Standard Methods
cites to Standard Methods Online for purchase
of individual methods?
2.
Can USEPA, the Agency, or anyone in the regulated community provide the
Board with a copy of the method entitled “The Determination of Radium-226 and
Radium-228 in Drinking Water by Gamma-ray Spectrometry Using HPGE or
11
Ge(Li) Detectors,” Revision 1.2, December 2004, cited by USEPA as available
from the Environmental Resources Center at the Georgia Institute of Technology?
3.
Can USEPA, the Agency, or anyone in the regulated community provide the
Board with a copy of Waters Method D6508, revision 2, entitled “Test Method
for Determination of Dissolved Inorganic Anions in Aqueous Matrices Using
Capillary Ion Electrophoresis and Chromate Electrolyte,” cited by USEPA as
available from Waters Corporation?
4.
Can or should the Board substitute the easily located method ASTM D6508-
00(2005)e2 in place of the Method cited as Waters Method D6508, revision 2 by
USEPA, which the Board could not locate from the listed source?
5.
Did the Board take an acceptable approach to the approved equivalent methods,
which USEPA codified as appendix A to 40 C.F.R. 141, by combining them with
the methods that USEPA approved by rulemaking within the text of the
regulations?
Revisions to the Lead and Copper Rule--Sections 611.350, 611.351, 611.353, 611.354,
611.355, 611.356, 611.357, 611.358, 611.359, and 611.884
USEPA revised the Lead and Copper Rule on October 10, 2007 (at 72 Fed. Reg. 57782).
The Lead and Copper Rule, codified as subpart I of 40 C.F.R. 141, sets forth a standard for the
control of lead in drinking water. Lead is a unique drinking water contaminant in that it enters
the water after the finished water has left the water treatment process, as the water travels
through the distribution system and to the consumer’s tap. Some of the lead leaches from lead
service lines, where the consumer’s plumbing connects to the distribution system, and some
leaches from brass plumbing fixtures and lead-soldered copper plumbing in the consumers’
homes.
6
Thus, the emphasis in the Lead and Copper Rule is not an absolute maximum
contaminant level, as measured at an entry point to the water distribution system, but on lead and
copper action levels and their frequency of exceedance at the consumers’ taps. The
consequences of exceeding the lead or copper action level include implementation of public
notice and public education requirements, treatment process requirements intended to make the
distributed water leach less lead from the service lines and plumbing, and requirements for
replacement of lead service lines by the supplier of drinking water.
USEPA stated that its amendments made seven targeted changes relating to monitoring,
treatment processes, public education, consumer awareness, and lead service line replacement.
6
Federal law has prohibited the use of lead pipes and leaded solder in public water supply
systems and building plumbing systems only since 1986, with limited exceptions.
See
42 U.S.C.
§§ 300g-6(a)(1) (2006); 40 C.F.R. 141.43(a)(1) (2007). It has prohibited the distribution and
installation of plumbing fixtures, pipe, solder, or other plumbing items that are not lead free only
since 1996.
See
42 U.S.C. §§ 300g-6(a)(3) (2006);
see also
42 U.S.C. §§ 300g-6(d) (defining
“lead free”); 40 C.F.R. 141.43(a)(3) (2007).
12
The amendments included (1) clarification of the definitions of “compliance period” and
“monitoring period”; (2) clarification that the minimum number of samples that a small-system
supplier must collect is five; (3) a change that would not allow a supplier to commence or
continue a reduced monitoring schedule if it exceeds the lead action level; (4) addition of a
requirement that a supplier must obtain prior state approval before it uses a new source of raw
water or makes a change in its treatment that would have a long-term effect on water quality; (5)
addition of a requirement that the supplier provide a notice that states the tap water sampling
results and information to help understand the significance of those results to the person whose
tap the sample was taken; (6) revisions to the public notice content and delivery requirements;
and (7) addition of a requirement that a supplier reevaluate lead service lines previously
classified as “replaced through testing” when it is required to resume a lead service line
replacement program.
The Board incorporated the October 10, 2007 revisions to the Lead and Copper Rule into
the Illinois regulations without substantive deviation. Only one series of the revisions made by
the Board warrants specific discussion in this opinion. That pertains to how the Board has
provided for the Agency to approve or disapprove of actions of a supplier.
Use of SEPs for Agency Approval of Public Education Materials.
Where State
approval is required for activities under the Lead and Copper Rule, the Board has made the
Agency responsible for those determinations. The Board has drafted the rules to specify the
Special Exception Permit (SEP) of Section 611.110 as the means by which the Agency is to
render its approvals. The mechanism of the SEP provides a defined context for Agency
determinations in writing, and it provides for Board review of Agency determinations where a
supplier believes that such review is necessary.
See
35 Ill. Adm. Code 611.110(a) and (c)
(2006); 415 ILCS 5/39(a) and 40 (2006).
One application of the SEP in this proceeding is unusual. That is the SEP’s use in
Section 611.355(a)(1) (corresponding with 40 C.F.R. 141.85(a)(1)) for the Agency to submit its
corrections to the supplier if the Agency determines that the language of the supplier’s public
education materials is inadequate. The USEPA rule requires the supplier to submit its public
education materials to the state prior to distributing them to its consumers. It allows, but does
not require, the state to approve of those materials prior to distribution. The Board’s proposal
includes the federal requirement that the supplier submit its public education materials to the
Agency prior to publication of those materials.
The Board has had to weigh various options to determine whether to provide for prior
State approval of materials before their distribution and how to provide for such prior approvals.
The Board has explored USEPA’s purposes behind its provision allowing states to require prior
approval of public education materials before their distribution. The revised rule allows the
supplier to tailor its public education materials to individual community needs.
See
72 Fed. Reg.
57782, 57790-91 (Oct. 10, 2007). This new flexibility in the language of the public education
materials gave rise to the need for state review of public education materials before their
distribution. State approval before distribution of those materials would assure their quality.
Further, USEPA prefers more rapid distribution of the public education materials, in order to
reduce exposures to lead.
See
72 Fed. Reg. 57782, 57791, 57794 (Oct. 10, 2007). Thus, the
13
Board must draft the requirement for submission of public education materials to the Agency for
review so that the Agency review assures the quality of the materials and so that the Agency
review delays distribution no more time than is necessary for such a review.
The SEP is the mechanism that the Board has written into several provisions of the
drinking water regulations to provide for an Agency determination whenever such a
determination is required under the corresponding federal rule. The SEP is well suited to a
situation where affirmative State approval is required before a supplier may act in some regard.
This is the ordinary situation in which the mechanism of the SEP appears in the rules. However,
in the context of the Section 611.255(a)(1) provision for State review of the public education
materials, options exist for drafting the rule that would require written action by the State only
for disapproval.
Once the supplier has submitted its public education materials to the Agency prior to
distribution, the Board has options as to how it will address State review of the materials before
their publication. First, the Board could make no provision for Agency approval or disapproval
of the public education materials before the supplier distributes them. As a second option, the
Board could refrain from requiring Agency approval prior to distribution, but require that the
supplier distribute corrected public education materials if the Agency, by a SEP, makes a
determination that the information submitted was inadequate and requires distribution of
corrected materials. A third option is that the Board could require submission to the Agency for
review, requiring that the Agency approve the materials before the supplier may distribute the
materials. The fourth option is for the Board to require submission to the Agency, then to allow
the Agency an opportunity to disapprove the distribution before it could begin. The fourth
option would allow the Agency the option of not acting on prospective distributions of public
education materials unless it determines that there is a problem with a particular distribution.
The Board disfavors the first option of not providing for Agency review that could affect
the content of public education materials disseminated in Illinois. The advantage of this
approach is that it would allow the most rapid distribution of the materials to the public, since
there would be no time lost for prior Agency review. However, the Board believes that the
purpose for mandatory submission of the public education materials to the State is to accord the
State an opportunity to review those materials. The Board believes that Agency review would
only be meaningful if it would allow the Agency the opportunity to edit, if necessary, the content
of the public information materials presented by the supplier. Inherent to this is that significant
Agency review would also give the Agency an opportunity to prevent the dissemination of
information that it deems inappropriate. The Board opted away from this first approach in the
proposal for public comment for both of these reasons.
The Board similarly disfavors the second option of allowing the Agency an opportunity
to require a second distribution of corrected public education materials if it determines that an
initial distribution was somehow defective. Under this second option, a requirement that the
supplier include the Agency in its distribution or a requirement that the supplier submit the
materials to the Agency within some short time after dissemination would have equal utility.
Like the first option, this would allow the most rapid distribution of the information to the
14
public. The problem is that this option would render meaningless the federal requirement that
the supplier submit its materials to the State prior to dissemination.
The purpose behind the federal requirement of submission to the State prior to
dissemination would be to provide an opportunity for the State to review the public education
materials prior to distribution. Providing for an Agency review that would only allow the
Agency to require re-distribution of corrected materials would have two significant
disadvantages: (1) it would involve the wasted expense, time, and resources of the defective
distribution, and (2) it would increase the opportunity for public misinformation and confusion
by the distribution of two sets of information, one of which was defective. Thus, this second
option would give the Agency the opportunity to assure the dissemination of information that it
deems acceptable, but it would not give the Agency the opportunity to prevent the distribution of
information that it determines is defective. The Board opted against this second option for these
reasons.
Elimination of the first two options would leave only the third and fourth options. Each
of those two options would provide meaningful opportunity for Agency review prior to the
supplier distributing its public education materials. Each would sacrifice time in the distribution
to the public in favor of the opportunity for the Agency to assure the quality and accuracy of the
information distributed. Under the third option, the supplier must wait for prior State approval
before it distributes the information. Under the fourth option, the supplier must wait a sufficient
time to allow the Agency to object to the content before its distribution. The Board can foresee
benefits and drawbacks associated with each of the third and fourth options, and the Board must
select between them based on the balancing of those benefits and drawbacks.
The third option would require express Agency approval of each distribution of public
education materials. This would have the benefits of assuring that the Agency has reviewed and
approved of every distribution before it occurs. Requiring express approval would eliminate any
ambiguity, and it would give suppliers the assurance that the Agency has approved whatever
they have distributed. On the other hand, there are significant drawbacks if the supplier must
wait for Agency approval before it distributes its public education materials. First, using this
option would require the Agency to render a formal determination for each distribution of public
education materials by every community water supply in the State.
7
This would impose the
greatest burden on Agency resources of all four options. This option would lengthen the
distribution process by the time it would take for the Agency to review and approve.
8
7
Formerly, only suppliers that detected lead above the action level were required to distribute
public education materials. Now the requirement extends to all community water supplies
without regard to whether a supplier exceeded the action level.
See
72 Fed. Reg. 57782, 57794
(Oct. 10, 2007). This would increase the number of public education distributions required.
8
This might require additional time for subsequent review and approval should the Agency
disapprove of the materials submitted, depending on how the Agency presents its disapproval
and how the supplier receives that disapproval. Agency disapproval would take the least time if
the Agency cites specific deficiencies and suggests corrections in its disapproval, and the
15
The fourth option, rather than requiring prior Agency approval before distribution of
public education materials, would allow the Agency an opportunity to require correction of the
materials before their distribution. Option four would have to allow whatever period of time is
reasonable for the Agency to review and disapprove the materials before distribution could
occur. This option would allow the Agency the freedom to render implicit approval to public
information materials through its own inaction, thus affording the Agency more discretion as to
how it commits its resources. It would nevertheless still give the Agency the opportunity to
assure the quality of the public education materials distributed in Illinois. There is a greater
burden in generating a written response to every set of materials after review, as under the third
option, than there is in reviewing every set but preparing a formal response only when the
Agency determines that there is a deficiency, as under the fourth option. Under option four, after
the time provided for Agency review has run, the Agency would no longer be able to disapprove
the materials, since its implicit approval would have been deemed by the rule.
The balance between the third and fourth options then hinges on the amount of time each
option would delay the distribution of public education materials, their relative commitments of
Agency resources, and the degree of certainty or uncertainty that would be associated with each.
The choice between the third and fourth options is difficult for the Board, and the Board may
change its choice upon final adoption, after the benefit of any public comments received.
Nevertheless, the Board has opted for the fourth option in this proposal for public comment. The
Board believes that providing the Agency with an opportunity to review and disapprove public
education materials before distribution is protective and less burdensome than requiring Agency
written approval of each set of public education materials prior to their distribution.
The Board has drafted Section 611.355(a)(1) to require a supplier to submit its public
education materials to the Agency before it distributes them, as required by 40 C.F.R.
141.85(a)(1). Since the Board believes that USEPA intended that the State conduct a meaningful
review that ensures the quality and content of the public education materials, the Board has
provided for Agency review before their distribution. The option for Agency review that the
Board has selected requires the Agency to act in an affirmative way by issuing a determination in
the form of a SEP only when it determines that there is a deficiency in the materials. However,
in order to allow the Agency to opt for prompt approval, the rule allows the Agency to issue a
SEP that approves the materials, and the supplier can immediately distribute them. If the
Agency does not issue a SEP within the time prescribed in the rule, Agency assent is implied
under the rule, and the supplier may distribute the materials. If the Agency issues a SEP, that
SEP must describe the deficiencies in a way that enables the supplier to correct the deficiencies
and distribute the materials as corrected. Of course, as provided by the SEP provision, at Section
611.110(c), the supplier has the option of appealing the Agency determination to the Board.
As included in this proposal for public comment, the procedure for Agency review of
public education materials includes seven separate segments. To include all of the segments in
Section 611.355(a)(1) would have required presenting all seven segments in a single subsection
at new subsection (a)(3). The Board chose to move the procedure, so that it could appear in a
supplier immediately incorporates the Agency suggestions into the materials.
16
series of seven separate subsections for enhanced clarity. As drafted by the Board for the
purposes of this proposal for public comment, Section 611.355(a)(3) provides a procedure for
submission of public education materials to the Agency, for Agency disapproval of those
materials in a SEP, for supplier response to an Agency-issued disapproval in the form of a SEP,
and for the timing of distribution of the materials. The provisions included in this proposal for
public comment could change upon final adoption in response to public comments. The
procedure set forth in the proposed version of this provision provides as follows:
1.
The supplier must submit its public education materials to the Agency no later
than 60 days prior to the date on which it plans to distribute them.
2.
The Agency may issue a SEP that approves the public education materials, so that
the supplier can immediately distribute them. This would allow quick distribution
without waiting where the Agency wishes to concur with the supplier and allow
this to happen.
3.
The Agency has 30 days after the date it received public education materials from
a supplier within which it may review those materials and issue a SEP that
notifies the supplier of the deficiencies and which describes the deficiencies in
sufficient detail to allow the supplier to correct its public education materials to
the satisfaction of the Agency.
4.
If the supplier has not received a SEP from the Agency that describes the
deficiencies as noted above within 45 days after the date on which it submitted its
public education materials to the Agency, the materials are deemed approved, and
the supplier may distribute them as scheduled.
5.
If the Agency issues a SEP that describes the deficiencies as noted above, the
supplier must make all changes exactly as described in the SEP before it
distributes its public education materials.
6.
If the Agency changes its position with regard to any of the deficiencies described
in the SEP, it may issue a revised SEP that expressly supersedes the previous
SEP, and the supplier must make all changes exactly as described in the revised
SEP before it distributes its public education materials.
7.
The Agency must issue a SEP or a revised SEP within 30 days after the date when
the Agency received the original public education materials from the supplier,
except where the Agency and the supplier have agreed that the Agency need issue
a SEP or revised SEP by a later date. Where the supplier and the Agency have
agreed that the Agency need issue a SEP or revised SEP by a later date, the
Agency must do so within the agreed time.
The purpose for allowing the Agency and the supplier to agree to a later time for issuance
of a SEP and for allowing the Agency to issue a revised SEP is to allow for negotiation or dialog
relating to the contents of the supplier’s public education materials. The Board believes that
17
allowing the Agency and the supplier to take more time to derive consensus would be more
efficient and less time-consuming than providing for a cycle of sequential submissions and
reviews. The object of the Agency review provision is the timeliest distribution of the most
effective public education materials. This result requires a balance between the time needed to
assure reasonable accuracy and the accuracy possible within a reasonable time. The Board
believes that allowing the Agency and the supplier the flexibility to conduct a dialog and to
reach a mutual consensus facilitates this end.
The tables that appear beginning on page 20 of this opinion list and briefly describe the
deviations from the literal text of the federal rules and the changes made in the existing text of
the Illinois rules that were not derived from federal amendments. The Board requests public
comment on the incorporation of the USEPA October 10, 2007 amendments to the Lead and
Copper Rule into the Illinois drinking water regulations. Specifically, the Board requests public
comment on the Section 611.355(a)(1) provision for Agency review of suppliers’ public
education materials.
1.
Is requiring written Agency action only where the Agency determines that
deficiencies exist the best option for Agency review of the materials?
2.
Is the provision that deems the materials approved and which allows the supplier
to proceed and distribute the materials in the absence of an Agency response
workable?
3.
Do the times required for submission to the Agency and provided for Agency
review work for the purpose?
4.
Does the provision that requires the Agency to describe the deficiencies it has
found appear adequate and workable to assure that the supplier is given a clear
indication of those deficiencies?
5.
Does the requirement that allows the supplier to proceed and distribute its
materials after it has addressed the Agency-determined deficiencies appear
adequate and workable to assure that the Agency concerns are addressed and that
publication occurs as rapidly as possible?
6.
Is it necessary to set forth express provisions for Agency issuance of a revised
SEP, and does such an express provision provide for the timeliest resolution of
any issues that might arise in the course of Agency review of a supplier’s public
education materials?
General Revisions and Deviations from the Federal Text
In incorporating the federal rules into the Illinois system, some deviation from the federal
text is unavoidable. This deviation arises primarily through differences between the federal and
state regulatory structure and systems. Some deviation also arises through errors in and
problems with the federal text itself. The Board conforms the federal text to the Illinois rules
18
and regulatory scheme and corrects errors found in the text in the course of these routine update
rulemakings.
In addition to the amendments derived from federal amendments, the Board often finds it
necessary to alter the text of various passages of the existing rules as provisions are opened for
update in response to USEPA actions. This involves correcting deficiencies, clarifying
provisions, and making other changes that are necessary to establish a clear set of rules that
closely parallel the corresponding federal requirements within the codification scheme of the
Illinois Administrative Code.
The Board updates the citations to the Code of Federal Regulations to the most recent
version available. As discussed above, the most recent versions of the Code of Federal
Regulations available to the Board is the July 1, 2005 edition for USEPA regulations (Title 40).
Thus, the Board has updated all citations to Title 40 to the 2006 edition of the Code of Federal
Regulations, adding references to later amendments using their appropriate Federal Register
citation, where necessary.
The Board substituted “or” for “/” in most instances where this appeared in the federal
base text, using “and” where more appropriate. The Board further used this opportunity to make
a number of corrections to punctuation, grammar, spelling, and cross-reference format
throughout the opened text. We changed “who” to “that” and “he” or “she” to “it,” where the
person to which the regulation referred was not necessarily a natural person, or to “he or she,”
where a natural person was evident; changed “which” to “that” for restrictive relative clauses;
substituted “must” for “shall”; capitalized the section headings and corrected their format where
necessary; and corrected punctuation within sentences.
In addition, the federal rules have been edited to establish a uniform usage throughout the
Board’s regulations. For example, with respect to “shall,” “will,” and “may,” “must” is used
when an action is required by the rule, without regard to whether the action is required of the
subject of the sentence or not. “Shall” is no longer used, since it is not used in everyday
language. Thus, where a federal rule uses “shall,” the Board substitutes “must.” This is a break
from our former practice where “shall” was used when the subject of a sentence has a duty to do
something. “Will” is used when the Board obliges itself to do something. “May” is used when
choice of a provision is optional. “Or” is used rather than “and/or,” and denotes “one or both.”
“Either . . . or” denotes “one but not both.” “And” denotes “both.”
The Joint Committee on Administrative Rules has requested that the Board refer to the
United States Environmental Protection Agency in the same manner throughout all of our bodies
of regulations—
i.e.
, air, water, drinking water, RCRA Subtitle D (municipal solid waste
landfill), RCRA Subtitle C (hazardous waste), underground injection control (UIC), etc. The
Board has decided to refer to the United States Environmental Protection Agency as “USEPA.”
The Board will continue this conversion in future rulemakings as additional sections become
open to amendment. The Board will further convert “EPA” used in federal text to “USEPA,”
where USEPA is clearly intended.
19
The Board has assembled tables to aid in the location of these alterations and to briefly
outline their intended purpose. Table 1 sets forth the miscellaneous deviations from the federal
text, and Table 2 itemizes the corrections to the pre-amended base text of the rules in detail.
Table 1 begins on page 20 of this opinion, and Table 2 begins on page 53. There is no further
discussion of most of the deviations and revisions elsewhere in this opinion.
Discussion of Corrective Amendments
The Board has traditionally used the occasion of these identical-in-substance updates to
correct segments of the base text of the Illinois regulations. These corrections are non-
substantive in effect. The Board is including a number of non-substantive corrections in this
docket.
When a necessary minor correction comes to the attention of the Board, Board staff
makes a note of the correction, and set it aside until the next opportunity to make the correction.
The next opportunity generally presents itself when the section involved is next opened for
amendment as a result of amendments to the corresponding federal text. The Board has
cataloged a small number of changes since the last SDWA update docket, SDWA Update,
USEPA Regulations (January 1, 2006 though June 30, 2006), R07-2, and SDWA Update,
USEPA Regulations (July 1, 2006 though December 31, 2006), R07-11 (July 26, 2007).
The Board will not discuss the bulk of the particular corrective amendments in this
segment of this discussion. Only one warrants specific discussion. That discussion follows this
paragraph. The corrections are itemized in the Table 1, which begins on page 20 of this opinion.
The Board requests that the Agency, JCAR, and the regulated community review the table and
the text of the corrections. The Board requests comment on the corrections. The Board also
asks for the assistance of the Agency, JCAR, and the regulated community in the process of
spotting and correcting errors or omissions in the rules. The Board requests that interested
persons submit suggestions for the correction of any errors of which they become aware. The
Board will either include the corrections in this docket or catalog them for future revisions, if the
suggestions relate to segments of the text that are not already involved in this proceeding and the
Board cannot add them.
Tabulation of Miscellaneous Housekeeping Amendments
The tables below list numerous corrections and amendments that are not based on current
federal amendments. The first table (which begins immediately below) includes deviations made
in this Proposal for Public Comment from the verbatim text of the federal amendments. The
second table (which begins immediately after Table 1, on page 53 below) contains corrections
and clarifications that the Board made in the base text involved in this proposal. The
amendments listed in this second table are not directly derived from the current federal
amendments. Some of the entries in these tables are discussed further in appropriate segments of
the general discussion beginning at page 6 of this opinion.
20
Table 1:
Deviations from the Text of the Federal Amendments
Illinois Section
40 C.F.R. Section
Revision(s)
307.4000(c)
430.02(g)
Updated the citation to the
Code of Federal
Regulations
to the most recent edition to
incorporate March 12, 2007 federal
amendments by reference
307.7500(c)
465.03(c)
Updated the citation to the
Code of Federal
Regulations
to the most recent edition to
incorporate March 12, 2007 federal
amendments by reference
310.107(b), “40 CFR
136”
136.3, 136.4, 136.5, and
136.6
Updated the citation to the
Code of Federal
Regulations
to the most recent edition to
incorporate March 12, 2007 federal
amendments by reference
611.350(c)(3)(E)
141.80(c)(3)(iii)
Changed “public water system” to
“supplier”; changed “State” to “Agency”
611.350(g)
141.80(g)
Changed “all water systems” to singular
“the supplier”; added the definite article
before “lead tap . . . results”; added the
definite article before “persons served”;
changed “sites (taps) . . . that are tested” to
singular “each site (tap) . . . that is tested”
611.351(b)(3)(C)
141.81(b)(3)(iii)
Added a comma before “as described” to
offset a parenthetical; added “any” before
“long-term change”; changed “it” to “the
addition or long-term change”
611.353(a)(1)
141.83(a)(1)
Changed “the lead or copper action level
was exceeded” to active-voice “the
supplier exceeded the pertinent action
level”; retained the ending period
611.354(b)(1)
141.84(b)(1)
Added the topical statement; retained the
structure divided into subsections
611.354(b)(1)(D)
141.84(b)(1)
Retained the structure subdivided into
subsections; retained the active-voice “the
supplier exceeded the action level” in place
of “the action level was exceeded”; added
“pursuant to” before “subsection (a) of this
Section”
611.354(b)(1)(E)
141.84(b)(1)
Subdivided the sentence into a separate
subsection
611.354(b)(1)(E)
141.84(b)(1)
Subdivided the sentence into a separate
subsection; changed “State” to “Agency”;
added “by a SEP issued pursuant to Section
21
611.110”
611.354(b)(2)
141.84(b)(2)
Added the topical statement; subdivided
the provision into subsections
611.354(b)(2)(A)
141.84(b)(2)
Subdivided the sentence into a separate
subsection; changed “any water system” to
“a supplier”; added “that is” before
“resuming”; changed the first appearance
of “a lead service line replacement
program” to “program”; removed the
definite article from before “cessation”;
added a comma before “as allowed” to
offset the parenthetical; changed “by” to
“pursuant to”; changed “shall” to “must”;
changed “sites that were previously
determined not to require” to active-voice
“sites that it had previously determined did
not require”; changed “through the
sampling provision under” to “pursuant to
the sampling provision of”
611.354(b)(2)(B)
141.84(b)(2)
Subdivided the sentence into a separate
subsection; changed “system” to
“supplier”; changed numeric “7 percent” to
written “seven percent”; changed “so” to
“so that”; changed “systems” to singular “a
supplier”
611.354(b)(2)(B)
141.84(b)(2)
Subdivided the sentence into a separate
subsection; changed “for those systems that
have completed” to singular “for a supplier
that has completed”; changed “State” to
“Agency”; changed “shall” to “must”;
added “by a SEP . . . Section 611.110”
offset by commas; added “completed”
before “replacement program”; changed
“when the system re-exceeds” to
“whenever the supplier has re-exceeded”
and added a comma to offset it as a
parenthetical
611.355 preamble
141.85 preamble
Moved the first sentence, which directs
attention to subsection (d), to the end of the
paragraph to place it in order; changed
“water systems that exceed” to singular “a
supplier that exceeds”; changed “all water
systems that exceed” to singular “a
supplier that exceeds”; changed “persons
served” to “persons who are served”;
22
changed “water system” to “supplier”;
changed “at sites that are tested” to “at
each site that the supplier has tested”
611.355(a)(1)
141.85(a)(1)
Changed “Non-transient” to lower-case
“non-transient”; changed “water systems”
to singular “a CWS or NTNCWS
supplier”; changed “language in . . . must
be included” to active-voice “the supplier
must include the language set forth in . . .”;
changed “water system” to “supplier”
(twice); added “set forth” before “below”;
changed “and be in plain language” to “and
the supplier must present the additional
information in plain language”; changed
“State” to “Agency”; added “as required by
. . . this Section” as a parenthetical offset
by a comma
611.355(a)(1)(A)
141.85(a)(1)(i)
Changed “water system” to “supplier”
611.355(a)(1)(A)
Board note
141.85(a)(1)(i)
Added the explanation of mandatory use of
the literal text of the statement, except for
the bracketed material
611.355(a)(1)(B)
Board note
141.85(a)(1)(ii)
Added the explanation of mandatory use of
the literal text of the statement, except for
the bracketed material
611.355(a)(1)(C)(ii)
141.85(a)(1)(iii)(B)
Changed “home/building” to “home and
building”
611.355(a)(1)(C)
Board note
141.85(a)(1)(iii)
Added the explanation of use of text of the
statement that includes the required
information, except for the bracketed
material
611.355(a)(1)(D)
141.85(a)(1)(iv)
Changed “their” to “his or her”
611.355(a)(1)(D)
Board note
141.85(a)(1)(iv)
Added the explanation of use of text of the
statement that includes the required
information, except for the bracketed
material
611.355(a)(1)(E)
141.85(a)(1)(v)
Changed “system’s” to “supplier’s”;
changed “system” to “supplier”; changed
“home/building” to “home and building”
611.355(a)(1)(E)
Board note
141.85(a)(1)(v)
Added the explanation of use of text of the
statement that includes the required
information, except for the bracketed
material
611.355(a)(1)(F)
141.85(a)(1)(vi)
Changed “your” to “the supplier’s”
(twice); changed “EPA’s” to “USEPA’s”
611.355(a)(1)(F) Board 141.85(a)(1)(vi)
Added the explanation of mandatory use of
23
note
the literal text of the statement, except for
the bracketed material
611.355(a)(2)
141.85(a)(2)
Changed “community water systems” to “a
CWS supplier”; added “do both of the
following”
611.355(a)(2)(A)
141.85(a)(2)(i)
Added “it must”; changed the ending
period to a semicolon and the ending
conjunction “and”
611.355(a)(2)(B)
141.85(a)(2)(ii)
Added “it must”; changed “low lead” to
hyphenated “low-lead”; changed “lead
free” to hyphenated “lead-free”; added
“components”
611.355(a)(3)
141.85(a)(1)
Added the topical statement to add the
material that replaces the last two
sentences of subsection (a)(1)
611.355(a)(3)(A)
141.84(a)(1)
Moved the last sentence of subsection
(a)(1); changed “water systems” to singular
“the supplier”; changed “State” to
“Agency”; changed “prior to delivery” to
“for review at least 60 days prior to its
planned date for delivery of the materials
to the public”
611.355(a)(3)(B)
141.85(a)(1)
Added provision for Agency approval by a
SEP
611.355(a)(3)(C)
141.85(a)(1)
Added provision for immediate distribution
upon Agency approval
611.355(a)(3)(D)
141.85(a)(1)
Added provision for Agency disapproval
and identification of deficiencies by a SEP
611.355(a)(3)(E)
141.85(a)(1)
Added provision for Agency issuance of
SEP within 30 days, allowing extension of
time by prior agreement
611.355(a)(3)(E)
Board note
141.85(a)(1)
Added explanation of the provision for a
revised SEP
611.355(a)(3)(F)
141.85(a)(1)
Added provision for the supplier to
proceed to publication if the Agency does
not issue a SEP within 45 days
611.355(a)(3)(G)
141.85(a)(1)
Added provision allowing the supplier to
proceed to publication if it incorporates all
Agency-indicated revisions
611.355(a)(3) Board
note
141.85(a)(1)
Added explanation of the Agency review
procedure
611.355(b)(1)
141.85(b)(1)
Changed “for public water systems
serving” to singular “a supplier that
serves”; changed “or contain” to “or it
must contain” preceded by a comma to
24
create an independent clause; changed
“persons” to singular “a person”; changed
“water system” to “the supplier”
611.355(b)(2)
141.85(b)(2)
Changed “for public water systems
serving” to singular “a supplier that
serves”; changed “or contain” to “or it
must contain” preceded by a comma to
create an independent clause; changed
“persons” to singular “a person”; changed
“water system” to “the supplier”
611.355(b)(2)(A)
141.85(b)(2)(i)
Added “the CWS supplier must”; changed
“materials meeting the content
requirements” to “materials that meet the
content requirements”; changed “all bill
paying customers” to hyphenated “all of its
bill-paying customers”
611.355(b)(2)(B)
141.85(b)(2)(ii)
Added the topical statement
611.355(b)(2)(B)(i)
141.85(b)(2)(ii)(A)
Added “the CWS supplier must”; changed
“they” to “the agencies”; changed “water
system’s” to “supplier’s”; changed “all the
organization’s” to plural “all of the
agencies’”; changed “community water
system’s” to “supplier’s”; changed “water
system” to “supplier” (twice); changed
“community based” to hyphenated
“community-based”; changed “serving
target populations” to “serving the target
populations”; changed “systems” to
singular “the supplier”; changed “all
organizations” to “each of the
organizations”
611.355(b)(2)(B)(ii)
141.85(b)(2)(ii)(B)
Added “the CWS supplier must”; changed
“to the following organizations listed” to
“to the organizations listed”; changed
“water system’s” to “supplier’s” (twice);
changed the ending colon to a period;
moved the subsequent paragraphs to
subsection (b)(2)(H)
611.355(b)(2)(B)(ii)
Board note
141.85(b)(2)(ii)(B)
Added explanation of the movement of text
to subsection (b)(2)(H)
611.355(b)(2)(B)(iii)
141.85(b)(2)(ii)(C)
Added “the CWS supplier must”; changed
“to the following organizations within the
service area” to “to the organizations listed
. . . that are located within the service
area”; changed “water system’s” to
25
“supplier’s”; changed the ending colon to a
period; moved the subsequent paragraphs
to subsection (b)(2)(I)
611.355(b)(2)(C)
141.85(b)(2)(iii)
Added “the CWS supplier must”; added a
comma before “except for” to offset the
parenthetical; changed “water system” to
“supplier”
611.355(b)(2)(C)
required statement
141.85(b)(2)(iii)
required statement
Changed “water system” to “supplier”
(twice); changed “water system’s” to
“supplier’s”; changed “State” to “Illinois
Environmental Protection Agency,
Division of Public Water Supply”; changed
“State” to “Agency”
611.355(b)(2)(D)
141.85(b)(2)(iv)
Added “the CWS supplier must”; changed
“water system’s” to “supplier’s”; changed
“system” to “CWS supplier”
611.355(b)(2)(E)
141.85(b)(2)(v)
Added “the CWS supplier must”; added a
comma after “television” to offset the final
element of a series
611.355(b)(2)(F)
141.85(b)(2)(vi)
Added “the CWS supplier must”; changed
“onw or more categories” to “one or more
of the categories”
611.355(b)(2)(G)
141.85(b)(2)(vii)
Changed “systems that are” to singular “a
CWS supplier that is”; changed “State” to
“Agency”; added “by a SEP . . . Section
611.110” offset as a parenthetical by
commas
611.355(b)(2)(H)
141.85(b)(2)(ii)(B)
Added the subsection to move material
611.355(b)(2)(H)(i)
141.85(b)(2)(ii)(B)(
1
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)(ii)
141.85(b)(2)(ii)(B)(
2
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)(iii)
141.85(b)(2)(ii)(B)(
3
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)(iv)
141.85(b)(2)(ii)(B)(
4
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)(v)
141.85(b)(2)(ii)(B)(
5
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)(vi)
141.85(b)(2)(ii)(B)(
6
)
Added the subsection to accommodate
moved material
611.355(b)(2)(H)
Board note
141.85(b)(2)(ii)(B)
Added explanation of the movement of
material
611.355(b)(2)(I)
141.85(b)(2)(ii)(C)
Added the subsection to move material
611.355(b)(2)(I)(i)
141.85(b)(2)(ii)(C)(
1
)
Added the subsection to accommodate
moved material; added the ending period
26
611.355(b)(2)(I)(ii)
141.85(b)(2)(ii)(C)(
2
)
Added the subsection to accommodate
moved material
611.355(b)(2)(I)(iii)
141.85(b)(2)(ii)(C)(
3
)
Added the subsection to accommodate
moved material
611.355(b)(2)(I) Board
note
141.85(b)(2)(ii)(B)
Added explanation of the movement of
material
611.355(b)(3)
141.85(b)(3)
Changed “community water system” to
“CWS supplier”; changed “pursuant to” to
“described in”
611.355(b)(3)(A)
141.85(b)(3)(i)
Changed “community water system shall”
to “CWS supplier must”
611.355(b)(3)(B)
141.85(b)(3)(ii)
Changed “community water system shall”
to “CWS supplier must”
611.355(b)(3)(C)
141.85(b)(3)(iii)
Changed “community water system” to
“CWS supplier”
611.355(b)(3)(D)
141.85(b)(3)(iv)
Changed “State” to “Agency”; added “by
as SEP . . . Section 611.110”; changed “the
State can allow activities in . . . to extend
beyond the 60-day requirement if needed
for implementation purposes” to “the
Agency must, on a case-by-case basis, by a
SEP . . . Section 611,110, extend the time
for the supplier to complete the public
education tasks set forth in . . . beyond the
60-day limit if it determines that the
extended time is needed for
implementation purposes on a case-by-case
basis”; changed “this extension must be
approved in writing by the State in advance
of” to active-voice “the Agency must issue
the SEP granting any extension prior to
expiration of”
611.355(b)(4)
141.85(b)(4)
Retained active-voice “supplier exceeds
the lead action level” in place of
“exceedance occurred”
611.355(b)(4)(C)
141.85(b)(4)(iii)
Changed “systems that are required” to “a
NTNCWS supplier that is”; changed
“State” to “Agency”; added “by a SEP . . .
Section 611.110” offset as a parenthetical
by commas
611.355(b)(5)
141.85(b)(5)
Changed “the State can allow activities in
. . . to extend beyond the 60-day
requirement if needed for implementation
purposes on a case-by-case basis” to “the
Agency must, on a case-by-case basis, by a
27
SEP . . . Section 611,110, extend the time
for the supplier to complete the public
education tasks set forth in . . . beyond the
60-day limit if it determines that the
extended time is needed for
implementation purposes”; changed “this
extension must be approved in writing by
the State in advance of” to active-voice
“the Agency must issue the SEP granting
any extension prior to expiration of”
611.355(b)(8)
141.85(b)(8)
Changed “community water system
serving” to “CWS supplier that serves”;
changed “their” to singular “its”
611.355(b)(8)(A)
141.85(b)(8)(i)
Changed “system serving” to “supplier that
serves”
611.355(b)(8)(B)
141.85(b)(8)(ii)
Changed “system serving” to “supplier that
serves”; changed “served by the system” to
“that it serves”; changed “that” to “which”
for a subsequent restrictive relative clause
611.355(b)(8)(C)
141.85(b)(8)(iii)
Changed “State” to “Agency”; added “by a
SEP . . . Section 611.110” offset as a
parenthetical by commas; changed
“systems serving” to singular “supplier that
serves”; added a comma before “as long
as” to offset the parenthetical; changed
“system” to “the supplier”; changed
“served by the supplier” to “that it serves”
611.355(d)
141.85(d)
Changed “notification of results” to
“requirement for consumer notice of tap
water monitoring results”
611.355(d)(1)
141.85(d)(1)
Changed “reporting requirement” to
“consumer notice requirement”; changed
“all water systems” to singular “a supplier”
611.355(d)(2)
141.85(d)(2)
Changed “timing of notifiaction” to
“timing of consumer notice”; changed “a
water system” to “the supplier”; changed
“the system” to “it”
611.355(d)(3)
141.85(d)(3)
Added “of consumer notice” after
“content”; added a comma after “reduce
exposure to lead in drinking water” to
offset the final element of a series
611.355(d)(4)
141.85(d)(4)
Added “of consumer notice” after
“delivery”; changed “State” to “Agency”
(twice); added “by a SEP . . . Section
611.110” offset as a parenthetical by a
28
comma; changed “non-transient
noncommunity water system” to
“NTNCWS supplier”; changed “system” to
“supplier”
611.356(c)(2)
141.86(c)(2)
Changed “a public water system that has”
to “a supplier whose system has”; removed
the unnecessary comma “water taps, that
can be used” that separated the restrictive
relative clause; changed “meeting the
sample site criteria” to “and which can
meet the sampling site criteria”; changed
“sample sites” to “sampling site”; changed
“must collect at least one sample from each
tap and then must collect additional
samples from those taps on different days
during the monitoring period to meet the
required number of sites” to “must collect
multiple samples from individual taps. To
accomplish this, the supplier must collect
at least one sample from each tap, then it
must collect additional samples from those
same taps on different days during the
monitoring period, in order to collect a
total number of samples that meets the
required number of sampling sites”;
changed “the State may allow these public
water systems” to singular “the Agency
must, by a SEP issued pursuant to Section
611.110, allow a supplier”; added “whose
system has fewer than five drinking water
taps” before “to collect”; changed “less
than” to “fewer than”; changed “provided
that” to “if it determines that”; added “and
that the reduced number of samples will
produce the same results as would the
collection of multiple samples from some
taps”; changed “the State must approve
this” to “Agency approval of a”; changed
“in writing” to “must be”; changed “the
system or onsite” to “the supplier or on on-
site”; changed “State” to “Agency”
611.356(d)(4)(A)
141.86(d)(4)(i)
Changed “a small or medium system
collecting” to “a small- or medium-sized
system supplier that collects”; changed the
comma to the conjunction “and” and
changed “that” to “which” that separated a
29
subsequent restrictive relative clause;
changed “the frequency” to “its
frequency”; changed “sampling shall
begin” to “reduced sampling may only
begin”
611.356(d)(4)(B)(i)
141.86(d)(4)(ii)
Retained the structure subdivided into
subsections; added “which” before
“maintains” for a restrictive relative clause;
changed “sampling shall begin” to
“reduced sampling may only begin”
611.356(d)(4)(C)(i)
141.86(d)(4)(iii)
Retained the structure subdivided into
subsections; changed “sampling shall
begin” to “reduced sampling may only
begin”
611.356(d)(4)(C)(ii)
141.86(d)(4)(iii)
Retained the structure subdivided into
subsections; changed “shall” to “must”
611.356(d)(4)(D)(i)
141.86(d)(4)(iv)(A)
Changed “sampling shall begin” to
“reduced sampling may only begin”;
changed “State” to “Agency”; changed
“systems” to singular “a supplier”
611.356(d)(4)(F)(ii)
141.86(d)(4)(vi)(A)
Changed “shall” to “must”
611.356(d)(4)(G)
141.86(d)(4)(vii)
Changed “State” to “Agency”; changed
“water system” to “supplier”
611.356(d)(4)(B)(i)
141.86(d)(4)(ii)(A)(
1
)
Changed “sampling shall begin” to
“reduced sampling may only begin”;
changed “State” to “Agency”; changed
“systems” to singular “a supplier”
611.356(d)(4)(G)
141.86(d)(4)(vii)
Changed “State” to “Agency”; changed
“water system” to “supplier”
611.356(d)(4)(H)(i)
141.86(d)(4)(vi)(B)(
1
)
Changed “shall” to “must”
611.356(g)(4)(A)
141.86(g)(4)(i)
Changed “shall” to “must”
611.356(g)(4)(A)
141.86(g)(4)(iii)
Changed “State” to “Agency”; changed
“water system” to “supplier”
611.357(e)(2)(A)(i)
141.87(e)(2)(i)(A)
Changed “sampling shall begin” to
“reduced sampling may only begin”
611.357(e)(2)(A)(ii)
141.87(e)(2)(i)(B)
Changed “sampling shall begin” to
“reduced sampling may only begin”
611.357(e)(2)(B)(iv)
141.87(e)(2)(ii)
Retained the structure subdivided into
subsections; changed “shall” to “must”
611.358(b)
141.88(b)
Changed “State” to “Agency”; added “by a
SEP issued pursuant to Section 611.110”
611.358(d)(1)(A)(iii)
141.88(d)(1)(i)
Retained the structure subdivided into
subsections; changed “shall” to “must”
611.358(e)(1)
141.88(e)(1)
Added a comma before “provided that” to
offset the parenthetical; added a comma
30
before “only if” to offset a second
parenthetical; added “only” before “if”
611.358(e)(2)
141.88(e)(2)
Added a comma before “provided that” to
offset the parenthetical; added a comma
before “only if” to offset a second
parenthetical; added “only” before “if”
611.360(a)(1)
141.90(a)(1)
Changed “monitoring periods” to singular
“a monitoring period”; added “on which”
after “date”; added a comma before “as
specified” to offset the parenthetical
611.360(a)(3)
141.90(a)(3)
Changed “State” to “Agency” (twice);
added “by a SEP . . . Section 611.110”
offset by commas
611.360(e)(1)(B)
141.90(e)(1)(ii)
Retained the structure subdivided into
subsections; changed “system” to
“supplier”
611.360(e)(3)
141.90(e)(3)
Changed numeric “3” to written “three”;
changed “system” to “supplier”; changed
“State” to “Agency”
611.381(c)(2)
141.74(a)(2)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods; added the method type
“test strips” as a topical heading
611.381(c)(2)(A)
Appendix A to subpart
C, table for
141.131(c)(2)
Changed “Method D99-003” to “ITS
Method D99-003”
611.381(c)(2)(A)
Board note
Appendix A to subpart
C, table for
141.131(c)(2)
Added explanation of the USEPA approval
as an alternative method
611.381(c)(2)(B)
141.131(c)(2)
Moved the federally derived text of
subsection (c)(2) to accommodate addition
of the alternative method from appendix A
to subpart C as subsection (c)(2)(A)
611.526(c)(1)
141.21(f)(3) table and
appendix A to subpart C,
table for 141.21(f)(3)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods; referenced
Standard
Methods
, 21st edition instead of Standard
Methods Online for Method 9221
611.526(c)(2)
141.21(f)(3) table and
appendix A to subpart C,
table for 141.21(f)(3)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9222
611.526(c)(3)
141.21(f)(3) table and
appendix A to subpart C,
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
31
table for 141.21(f)(3)
Method 9221
611.526(c)(4)
141.21(f)(3) table and
appendix A to subpart C,
table for 141.21(f)(3)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9223
611.526(c) Board note
141.21(f)(3) table and
appendix A to subpart C,
table for 141.21(f)(3)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
9221, Method 9222, and Method 9223,
including explanation of USEPA approval
as equivalent methods
611.531(a)(2)
141.74(a)(1) table and
appendix A to subpart C,
table for 141.74(a)(1)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods
611.531(a)(2)(A)(i)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9221
611.531(a)(2)(A)(ii)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9222
611.531(a)(2)(A)(iii)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9223
611.531(a)(2)(B)(i)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9221
611.531(a)(2)(B)(i)
Board note
141.74(a)(1) table, note
8
Changed numeric “7” to written “seven”
611.531(a)(2)(B)(ii)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9222
611.531(a)(2)(C)(i)
141.74(a)(1) table, note
1, and appendix A to
subpart C, table for
141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 9215
611.531(a)(2)(D)
Board note
141.74(a)(1) table, note
13
Added the federal footnote material as a
Board note
611.531(a)(2)(D)(i)
141.74(a)(1) table and
appendix A to subpart C,
table for 141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 2130
32
611.531(a)(2)(E)
141.74(a)(1) table and
appendix A to subpart C,
table for 141.74(a)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 2550
611.531(a)(2) Board
note
141.21(a)(1) table and
appendix A to subpart C,
table for 141.74(a)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
2130, Method 9215, Method 9221, Method
9222, and Method 9223, including
explanation of USEPA approval as
equivalent methods
611.531(b)(1)
141.74(a)(2) table and
appendix A to subpart C,
table for 141.74(a)(12)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods
611.531(b)(1)(A)(i)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(1)(B)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(1)(C)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(1)(D)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(2)(A)(i)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(2)(B)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(2)(C)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(2)(D)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
33
141.74(a)(2)
611.531(b)(2)(E)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-Cl
611.531(b)(3)(A)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-ClO
2
611.531(b)(3)(C)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Renamed “327.0, Revision 1.1” to
“USEPA OGWDW Methods, Method
327.0”
611.531(b)(4)
141.74(a)(2) table, note
1, and appendix A to
subpart C, table for
141.74(a)(2)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-O
3
611.531(b) Board note
141.21(a)(2) table and
appendix A to subpart C,
table for 141.74(a)(2)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-Cl, Method 4500-ClO
2
, and Method
4500-O
3
, including explanation of USEPA
approval as equivalent methods
611.611(a)
141.74(a)(1) table and
appendix A to subpart C,
table for 141.74(a)(1)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods
611.611(a) Board note
141.23(k)(1) table, note
4 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method 3120
and Method 3113, including explanation of
USEPA approval as equivalent methods
611.611(a)(1)(A)(i)
141.23(k)(1) table
Changed “D1067-92, 02 B” to “D1067-92
B or D1067-02 B”
611.611(a)(1)(A)(ii)
141.23(k)(1) table, note
4 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 2320
611.611(a)(2)(B)
141.23(k)(1) table
Changed “D3697-92, 02” to “D3697-92 or
D3697-03”
611.611(a)(2)(D)
141.23(k)(1) table, note
4 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(2)(E)
Appendix A to subpart
Changed “EPA Method 200.5” to “USEPA
34
C, table for 141.23(k)(1) Methods: Method 200.5”
611.611(a)(2)(E)
Board note
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(3) Board
note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(3)(A)(ii)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(3)(A)(ii)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(2)(D)(i)
141.23(k)(1) table
Changed “D2972-97, 03 C” to “D2972-97
or D2972-03 C”
611.611(a)(3)(D)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(3)(D)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(3)(E)(i)
141.23(k)(1) table
Changed “D2972-97, 03 B” to “D2972-97
or D2972-03 B”
611.611(a)(3)(E)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3114
611.611(a)(3)(E)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3114, including explanation of USEPA
approval as equivalent methods
611.611(a)(3)(F) Board
note
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(3)(F) Board
note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(5)(A)(ii)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
35
141.23(k)(1)
611.611(a)(5)(A)(ii)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(5)(C)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(5)(C)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
approval as equivalent methods
611.611(a)(5)(D)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(5)(D)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(5)(E)
Board note
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(5)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(6)(A)(ii)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(6)(A)(ii)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(6)(D)(i)
141.23(k)(1) table
Changed “D3645-97, 03 B” to “D3645-97
or D3645-03 B”
611.611(a)(6)(D)(ii)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
36
611.611(a)(6)(D)(ii)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(6)(E)
Board note
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(6)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(7)(D)
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(7)(D)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(7)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(7)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(8)(A)(i)
141.23(k)(1) table
Changed “D511-93, 03 C” to “D511-93 or
D511-03 C”
611.611(a)(8)(A)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3500-Ca
611.611(a)(8)(A)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3500-Ca, including explanation of USEPA
approval as equivalent methods
611.611(a)(8)(B)(i)
141.23(k)(1) table
Changed “D511-93, 03 C” to “D511-93 or
D511-03 C”
611.611(a)(8)(B)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(8)(B)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
37
approval as equivalent methods
611.611(a)(8)(C)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(8)(C)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(8)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(8)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(9)(A)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(9)(A)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(9)(D)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(9)(D)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(9)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(9)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(10)(A)(i)
141.23(k)(1) table
Changed “D1688-95, 02 C” to “D1688-95
or D1688-02 C”
611.611(a)(10)(A)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(10)(A)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
38
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(10)(B)(i)
141.23(k)(1) table
Changed “D1688-95, 02 C” to “D1688-95
or D1688-02 C”
611.611(a)(10)(B)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(10)(B)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
approval as equivalent methods
611.611(a)(10)(C)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(10)(C)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(10)(F)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(10)(F)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(11)(A)
141.23(k)(1) table
Changed “D1125-95 (Reapproved 1999)”
to “D1125-95(1999)”
611.611(a)(11)(B)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 2510
611.611(a)(11)(B)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
2510, including explanation of USEPA
approval as equivalent methods
611.611(a)(12)(A)(i)
Board note
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(12)(A)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-CN
-
611.611(a)(12)(A)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-CN
-
, including explanation of
39
USEPA approval as equivalent methods
611.611(a)(12)(B)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-CN
-
611.611(a)(12)(B)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-CN
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(12)(C)
Board note
141.23(k)(1) table
Changed “spectro-photometric
semiautomated” to “spectrophotometric,
semiautomated”
611.611(a)(12)(D)(ii)
141.23(k)(1) table
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-CN
-
611.611(a)(12)(D)(ii)
Board note
141.23(k)(1) table
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-CN
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(12)(F)
Board note
141.23(k)(1) table
Changed “micro distillation” to
“microdistillation”
611.611(a)(12)(G)(i)
141.23(k)(1) table
Changed “ASTM D6888-04” to “ASTM
Method D6888-03”
611.611(a)(12)(G)(ii)
141.23(k)(1) table
Changed “OIA-1677 DW” to “OI
Analytical Method OIA-1677 DW”
611.611(a)(13)(A)(i)
141.23(k)(1) table
Changed “300.0, 300.1” to “Method 300.1
or Method 300.1”
611.611(a)(13)(A)(ii)
141.23(k)(1) table
Changed “D4237-97, 03” to “D4237-97 or
D4237-03”
611.611(a)(13)(A)(iii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4110
611.611(a)(13)(A)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4110, including explanation of USEPA
approval as equivalent methods
611.611(a)(13)(B)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-F
-
611.611(a)(13)(B)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-F
-
, including explanation of USEPA
40
approval as equivalent methods
611.611(a)(13)(C)(i)
appendix A to subpart C,
table for 141.23(k)(1)
Changed “D1179-93, 04” to “D1179-93 or
D1179-04”
611.611(a)(13)(C)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-F
-
611.611(a)(13)(C)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-F
-
, including explanation of USEPA
approval as equivalent methods
611.611(a)(13)(E)(i)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-F
-
611.611(a)(13)(E)(i)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-F
-
, including explanation of USEPA
approval as equivalent methods
611.611(a)(13)(F)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Changed “Method D6508, Rev. 2” for
Waters Corp. to “ASTM Method D6508-
00(2005)e2 (rev. 2)”
611.611(a)(13)(F)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of the change from a
Method that the Board could not locate
from Waters Corp. to an ASTM Method
that is identical to the method as obtained
from USEPA
611.611(a)(14)(A)(i)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D3559-96, 03” to “D3559-96 or
D1179-03”
611.611(a)(14)(A)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(14)(A)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(14)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(14)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(15)(A)(i)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D511-93, 03” to “D511-93 or
D511-03”
41
611.611(a)(15)(A)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(15)(A)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
approval as equivalent methods
611.611(a)(15)(B)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(15)(B)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(15)(C)(i)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D511-93, 03” to “D511-93 or
D511-03”
611.611(a)(15)(C)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3500-Mg
611.611(a)(15)(C)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3500-Mg, including explanation of USEPA
approval as equivalent methods
611.611(a)(15)(B)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(15)(D)
141.23(k)(1) table
Changed “ASTM D6919-03” to “ASTM
Method D6919-03”
611.611(a)(15)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(15)(E)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(16)(A)(ii)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D3223-97, 02” to “D3223-97 or
D3223-02”
611.611(a)(16)(A)(iii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3112
611.611(a)(16)(A)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
42
3112, including explanation of USEPA
approval as equivalent methods
611.611(a)(17)(A)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(17)(A)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(17)(D)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(17)(D)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
approval as equivalent methods
611.611(a)(17)(E)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(a)(17)(E)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(17)(F)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(17)(F)
Board note
141.23(k)(1) table, note
14 and appendix A to
subpart C, table for
141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(18)(A)(i)
141.23(k)(1) table
Changed “300.0, 300.1” to “Method 300.1
or Method 300.1”
611.611(a)(18)(A)(ii)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D4327-97, 03” to “D4327-97 or
D4327-03”
611.611(a)(18)(A)(iii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4110
611.611(a)(18)(A)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4110, including explanation of USEPA
approval as equivalent methods
611.611(a)(18)(B)(iii)
141.23(k)(1) table and
Referenced
Standard Methods
, 21st edition
43
appendix A to subpart C,
table for 141.23(k)(1)
instead of Standard Methods Online for
Method 4500-NO
3
-
611.611(a)(18)(B)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
3
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(18)(C)(i)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-NO
3
-
611.611(a)(18)(C)(i)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
3
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(18)(D)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-NO
3
-
611.611(a)(18)(D)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
3
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(18)(E)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Changed “Method D6508, Rev. 2” for
Waters Corp. to “ASTM Method D6508-
00(2005)e2 (rev. 2)”
611.611(a)(18)(E)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of the change from a
Method that the Board could not locate
from Waters Corp. to an ASTM Method
that is identical to the method as obtained
from USEPA
611.611(a)(19)(A)(i)
141.23(k)(1) table
Changed “300.0, 300.1” to “Method 300.1
or Method 300.1”
611.611(a)(19)(A)(ii)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “D4327-97, 03” to “D4327-97 or
D4327-03”
611.611(a)(19)(A)(iii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4110
611.611(a)(19)(A)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4110, including explanation of USEPA
approval as equivalent methods
611.611(a)(19)(B)(iii)
141.23(k)(1) table and
appendix A to subpart C,
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
44
table for 141.23(k)(1)
Method 4500-NO
3
-
611.611(a)(19)(B)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
3
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(19)(C)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-NO
3
-
611.611(a)(19)(C)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
3
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(19)(D)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-NO
2
-
611.611(a)(19)(D)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-NO
2
-
, including explanation of
USEPA approval as equivalent methods
611.611(a)(19)(E)
141.23(k)(1) table
Changed “Method D6508, Rev. 2” for
Waters Corp. to “ASTM Method D6508-
00(2005)e2 (rev. 2)”
611.611(a)(19)(E)
Board note
141.23(k)(1) table
Added explanation of the change from a
Method that the Board could not locate
from Waters Corp. to an ASTM Method
that is identical to the method as obtained
from USEPA
611.611(a)(20)(A)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-P
611.611(a)(20)(A)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-P, including explanation of USEPA
approval as equivalent methods
611.611(a)(20)(B)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-P
611.611(a)(20)(B)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-P, including explanation of USEPA
45
approval as equivalent methods
611.611(a)(20)(F)(i)
141.23(k)(1) table
Changed “300.0, 300.1” to “Method 300.1
or Method 300.1”
611.611(a)(20)(F)(ii)
141.23(k)(1) table
Changed “D4327-97, 03” to “D4327-97 or
D4327-03”
611.611(a)(20)(F)(iii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4110
611.611(a)(20)(F)(iii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4110, including explanation of USEPA
approval as equivalent methods
611.611(a)(20)(G)
141.23(k)(1) table
Changed “Method D6508, Rev. 2” for
Waters Corp. to “ASTM Method D6508-
00(2005)e2 (rev. 2)”
611.611(a)(20)(G)
Board note
141.23(k)(1) table
Added explanation of the change from a
Method that the Board could not locate
from Waters Corp. to an ASTM Method
that is identical to the method as obtained
from USEPA
611.611(a)(21)(B)
141.23(k)(1) table
Changed “D1293-95, 99” to “D1293-95 or
D1293-99”
611.611(a)(21)(C)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-H
+
611.611(a)(21)(C)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-H
+
, including explanation of USEPA
approval as equivalent methods
611.611(a)(22)(A)(i)
141.23(k)(1) table
Changed “D3859-98, 03” to “D3859-98 or
D3859-03”
611.611(a)(22)(A)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3114
611.611(a)(22)(A)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3114, including explanation of USEPA
approval as equivalent methods
611.611(a)(22)(D)(i)
141.23(k)(1) table
Changed “D3859-98, 03” to “D3859-98 or
D3859-03”
611.611(a)(22)(D)(ii)
141.23(k)(1) table and
appendix A to subpart C,
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
46
table for 141.23(k)(1)
Method 3113
611.611(a)(22)(D)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3113, including explanation of USEPA
approval as equivalent methods
611.611(a)(22)(E)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(22)(E)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(23)(C)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Changed “D859-94, 00” to “ASTM D859-
94, D859-00”
611.611(a)(23)(C)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(23)(D)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-SiO
2
611.611(a)(23)(D)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-SiO
2
, including explanation of
USEPA approval as equivalent methods
611.611(a)(23)(E)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-SiO
2
611.611(a)(23)(E)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-SiO
2
, including explanation of
USEPA approval as equivalent methods
611.611(a)(23)(F)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 4500-SiO
2
611.611(a)(23)(F)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
4500-SiO
2
, including explanation of
USEPA approval as equivalent methods
611.611(a)(23)(G)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(a)(23)(G)(ii)
141.23(k)(1) table and
Added explanation of reference to
47
Board note
appendix A to subpart C,
table for 141.23(k)(1)
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3120, including explanation of USEPA
approval as equivalent methods
611.611(a)(23)(H)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(23)(H)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(24)(B)(ii)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(a)(24)(B)(ii)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, including explanation of USEPA
approval as equivalent methods
611.611(a)(24)(C)
141.23(k)(1) table
Changed “ASTM D6919-03” to “ASTM
Method D6919-03”
611.611(a)(24)(D)
Appendix A to subpart
C, table for 141.23(k)(1)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(a)(24)(D)
Board note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of USEPA approval as
an equivalent method
611.611(a)(25)
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 2550
611.611(a)(25) Board
note
141.23(k)(1) table and
appendix A to subpart C,
table for 141.23(k)(1)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
2550, including explanation of USEPA
approval as equivalent methods
611.612(f)(2)(A)(i)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.612(f)(2)(A)(ii)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.612(f)(2)(A)(iii)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.612(f)(2)(A)
Board note
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, 3113, and 3120, including
48
explanation of USEPA approval as
equivalent methods
611.612(f)(2)(C)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.611(f)(2)(C) Board
note
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Added explanation of USEPA approval as
an equivalent method
611.612(f)(3)(A)(i)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(f)(3)(A)(ii)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3113
611.611(f)(3)(A)(iii)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(f)(3)(A)
Board note
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
3111, 3113, and 3120, including
explanation of USEPA approval as
equivalent methods
611.612(f)(3)(C)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.612(f)(3)(C) Board
note
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Added explanation of USEPA approval as
an equivalent method
611.612(f)(4)(A)(i)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3111
611.611(f)(4)(A)(ii)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 3120
611.611(f)(4)(A)
Board note
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method 3111
and 3120, including explanation of USEPA
approval as equivalent methods
611.612(f)(4)(C)
143.4(b) table and
appendix A to subpart C,
table for 143.4(b)
Changed “EPA Method 200.5” to “USEPA
Methods: Method 200.5”
611.612(f)(4)(C) Board
note
143.4(b) table and
appendix A to subpart C,
Added explanation of USEPA approval as
an equivalent method
49
table for 143.4(b)
611.645 “2,4-D”
141.24(e)(1) table
Changed “, 98” to “or D5317-98”
611.645 “2,4,5-TP
(Silvex)”
141.24(e)(1) table
Changed “, 98” to “or D5317-98”
611.645 “pentachloro-
phenol”
141.24(e)(1) table and
appendix A to subpart C,
table for 141.24(e)(1)
Changed “D5317-93, 98 (Reapproved
2003) to “D5317-93 or D5317-98(2003)”
611.645 “picloram”
141.24(e)(1) table and
appendix A to subpart C,
table for 141.24(e)(1)
Changed “D5317-93, 98 (Reapproved
2003) to “D5317-93 or D5317-98(2003)”
611.645 note 1
141.24(e)(1) table, note
5
Changed “this method” to “denotes that
Syngenta Method AG-625”; changed
“Method AG-625” to “Syngenta Method
AG-625” (twice); changed “mg/L” to
“mg/ℓ”; changed “μg/L” to “μg/ℓ”
611.720(a)(1)(A)(ii)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7110, including explanation of USEPA
approval as equivalent methods
611.720(a)(2)(A)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7110
611.720(a)(2)(A)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7110, including explanation of USEPA
approval as equivalent methods
611.720(a)(3)(C)(iii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Ra
611.720(a)(3)(C)(iv)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Ra
611.720(a)(3)(C)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7500-Ra, including explanation of USEPA
approval as equivalent methods
611.720(a)(3)(J)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Changed “GA” to “Georgia Radium
Method”
611.720(a)(4)(A)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Ra
50
611.720(a)(4)(A)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7500-Ra, including explanation of USEPA
approval as equivalent methods
611.720(a)(3)(I)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Changed “GA” to “Georgia Radium
Method”
611.720(a)(5)(A)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-U
611.720(a)(5)(A)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7500-U, including explanation of USEPA
approval as equivalent methods
711.720(a)(5)(C)(ii)
141.25(a) table
Changed “D3972-97, 02” to “D3972-97 or
D3972-02”
711.720(a)(5)(C)(iii)
141.25(a) table
Changed “D5174-97, 02” to “D5174-97 or
D5174-02”
711.720(a)(5)(C)(iv)
Board note
appendix A to subpart C,
table for 141.75(a)
Added explanation of USEPA approval as
an equivalent method
711.720(a)(6)(A)(ii)
141.25(a) table
Changed “D3649-91, 98a” to “D3649-91
or D3649-98a”
611.720(a)(5)(B)(i)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7120
611.720(a)(5)(B)(ii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Cs
611.720(a)(5)(B)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method 7100
and 7500-Cs, including explanation of
USEPA approval as equivalent methods
711.720(a)(7)(A)(i)
141.25(a) table
Changed “D3649-91, 98a” to “D3649-91
or D3649-98a”
711.720(a)(7)(A)(ii)
141.25(a) table
Changed “D4785-93, 98” to “D4785-93 or
D4785-98”
611.720(a)(7)(B)(i)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7120
611.720(a)(7)(B)(ii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-I
51
611.720(a)(7)(B)(iii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-I
611.720(a)(7)(B)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Methods
7100 and 7500-I, including explanation of
USEPA approval as equivalent methods
611.720(a)(8)(A)(ii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Sr
611.720(a)(8)(A)(ii)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7500-Sr, including explanation of USEPA
approval as equivalent methods
711.720(a)(9)(A)
141.25(a) table
Changed “D4107-91, 98” to “D4107-91 or
D4107-98”
611.720(a)(9)(A)(ii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-
3
H
611.720(a)(9)(A)(ii)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
7500-
3
H, including explanation of USEPA
approval as equivalent methods
711.720(a)(10)(A)(i)
141.25(a) table
Changed “D3649-91, 98a” to “D3649-91
or D3649-98a”
711.720(a)(10)(A)(ii)
141.25(a) table
Changed “D4785-93, 98” to “D4785-93 or
D4785-98”
611.720(a)(10)(B)(i)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7120
611.720(a)(10)(B)(ii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-Cs
611.720(a)(10)(B)(iii)
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Referenced
Standard Methods
, 21st edition
instead of Standard Methods Online for
Method 7500-I
611.720(a)(10)(B)
Board note
141.25(a) table and
appendix A to subpart C,
table for 141.75(a)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Methods
7120, 7500-Cs, and 7500-I, including
explanation of USEPA approval as
equivalent methods
52
611.802(c)(2)(A)(vii)
141.402(c)(2) table
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods; referenced
Standard
Methods
, 21st edition instead of Standard
Methods Online for Method 9222
611.802(c)(2)(A)
Board note
141.402(c)(2) table and
appendix A to subpart C,
table for 141.402(c)(2)
Added explanation of reference to
Standard Methods
, 21st edition instead of
Standard Methods Online for Method
9222, including explanation of USEPA
approval as equivalent methods
611.802(c)(2)(B)
Board note
Appendix A to subpart
C, table for
141.402(c)(2)
Added explanation of USEPA approval as
an equivalent method
611.884(d)(1) required
statement
141.154(d)(1)
Changed “utility” to “supplier”; changed
numeric “2” to written “two”
611.884(d)(1)
141.154(d)(2)
Changed “system” to “supplier”; changed
“State” to “Agency”
611.1004(b)(4)
141.704(b)(4)
Retained the structure of the methods
listings, placing the approved alternative
methods together with the listing of all
approved methods; added “incorporated by
reference . . . Section 611.102”
611.1004(b)(4) Board
note
141.704(b)(4)
Added explanation of USEPA approval as
an equivalent method
Table2:
Board Housekeeping Amendments
Section
Source
Revision(s)
307.4000(b)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
307.4000(d)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
307.7500(b)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
307.7500(d)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
2.302”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
3.2”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
3.3”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
53
310.107(b), “40 CFR
3.10”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
3.2000”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
25”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b),
“appendix D to 40
CFR 122”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
136”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b), “40 CFR
403”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including removal of the
obsolete
Federal Register
citation
310.107(b), “40 CFR
403.12”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including removal of the
obsolete
Federal Register
citation
310.107(b),
“appendix D to 40
CFR 403”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
310.107(b),
“appendix G to 40
CFR 403”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including removal of the
obsolete
Federal Register
citation
310.107(b), “40 CFR
503”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including removal of the
obsolete
Federal Register
citation
310.107(c), “18 USC
1001”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1251”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1284”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1284”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1292”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1318”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
54
310.107(c), “33 USC
1319”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “33 USC
1345”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
310.107(c), “42 USC
6921-6939e and
6441-6949a”
Board
Updated the citation to the
United States Code
to the
most recent edition, including removal of the obsolete
Federal Register
citation
611.102(a) “Georgia
Radium Method”
Board
Added a standardized definition of the new method to act
as a short title in the regulations
611.102(a) “ITS
Method D99-003”
Board
Added a standardized definition of the new method to act
as a short title in the regulations
611.102(a) “OI
Analytical Method
OIA-1677”
Board
Added a standardized definition of the new method to act
as a short title in the regulations
611.102(a) “Standard
Methods Online”
Board
Added a standardized definition of the new method to act
as a short title in the regulations
611.102(a) “Technical
Notes on Drinking
Water Methods”
Board
Added a standardized definition of the document to act as
a short title in the regulations
611.102(a) “USEPA
Method 1622 (05)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
Method 1622 (01)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
Method 1622 (99)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
Method 1623 (05)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
Method 1623 (01)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
Method 1623 (99)”
Board
Removed the standardized definition establishing a short
title in the regulations
611.102(a) “USEPA
NERL Method 200.5”
Board
Added a standardized definition of the document to act as
a short title in the regulations
611.102(a) “USEPA
OGWDW Methods”
Board
Added the references to the 1999, 2001, and 2005
versions of Method 1622 and Method 1623
611.102(a) “USEPA
Organic Methods”
Board
Removed the references to Method 515.4 and Method
531.2, which are “USEPA OGWDW Methods”; removed
“are both available on-line from USEPA, Office of
Ground Water and Drinking Water”
611.102(b)
“ALPKEM”
Board
Added the source and reference for the new method,
“Method OIA-1677 DW”
55
611.102(b)
“ALPKEM” Board
note
Board
Added the information relating to on-line availability of
the method from USEPA
611.102(b)
“AWWA,” “Standard
Methods, 20th ed.,”
“Method 3120 B”
Board
Changed “Section 611.612” to “Sections 611.611 and
611.612”
611.102(b)
“AWWA,” “Standard
Methods, 20th ed.,”
“Method 7120”
Board
Changed “7120 B” to “7120”; removed the title of
Method 7120 B, “Gamma Spectrometric Method”
611.102(b)
“AWWA,” “Standard
Methods, 20th ed.,”
“Method 7500-Ra D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 2130 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 2320 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 2510 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 2550”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3111 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3111 D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3112 B”
Board
Added the reference to the method
56
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3113 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3114 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3120 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3500-Ca B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3500-Ca D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 3500-Mg B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4110 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-ClO
2
C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-CN
-
E”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-CN
-
F”
Board
Added the reference to the method
57
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-CN
-
F”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-F
-
B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-F
-
C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-F
-
D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-F
-
E”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-H
+
B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-NO
2
-
B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-NO
3
-
D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-NO
3
-
E”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-NO
3
-
F”
Board
Added the reference to the method
58
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-O
3
B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-P E”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-P F”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-SiO
2
C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-SiO
2
D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 4500-SiO
2
E”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 6610”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7110 B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7110 C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7120”
Board
Added the reference to the method
59
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-Cs B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-
3
H B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-I B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-I C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-I D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-Ra B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-Ra C”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-Ra D”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-Sr B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-U B”
Board
Added the reference to the method
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.,”
“Method 7500-U C”
Board
Added the reference to the method
60
611.102(b)
“AWWA,” “Standard
Methods, 21st ed.”
Board note
Board
Changed “Standard Methods is” to “individual methods
from Standard Methods are”
611.102(b) “ASTM,”
“ASTM Method
D511-03A and B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D859-94”
Board
Updated “D859-88” to “D859-94” and “August 19,
1988” to “1994”
611.102(b) “ASTM,”
“ASTM Method
D859-00”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D859-05”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D1067-02 B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D1125-95”
Board
Updated “D1125-91 A” to “DD1125-95 A” and “June 15,
1991” to “1995, reapproved 1999”
611.102(b) “ASTM,”
“ASTM Method
D1179-99 B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D1179-04 B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D1253-03”
Board
Changed “Section 611.612” to “Sections 611.611 and
611.612”
611.102(b) “ASTM,”
“ASTM Method
D1293-95 A or B”
Board
Updated “D1293-95” to “D1293-95 A or B” and
“October 26, 1984” to “1995”
611.102(b) “ASTM,”
“ASTM Method
D1293-99 A or B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D1688-95 A or C”
Board
Updated “D1688-90 A or C” to “D1688-95 A or C” and
“March 15, 1990” to “1995”
611.102(b) “ASTM,”
“ASTM Method
D1688-02 A or C”
Board
Added the reference to the new method
61
611.102(b) “ASTM,”
“ASTM Method
D2036-91 A or B”
Board
Updated “D2036-91 A or B” to “D2036-98 A or B” and
“September 15, 1991” to “1998”
611.102(b) “ASTM,”
“ASTM Method
D2036-06 A or B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D2972-97 B or C”
Board
Updated “D2972-93 B or C” to “D2972-97 B or C” and
“1993” to “1997”
611.102(b) “ASTM,”
“ASTM Method
D2972-03 B or C”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3223-97”
Board
Updated “D3223-91” to “D3223-97” and “September 23,
1991” to “1997”
611.102(b) “ASTM,”
“ASTM Method
D3223-02”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3559-03 D”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3645-97 B”
Board
Corrected “1993” to “1997”
611.102(b) “ASTM,”
“ASTM Method
D3645-03 B”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3649-98a”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3697-02”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3859-98 A”
Board
Updated “D3859-93 A” to “D3859-98 A” and “1993” to
“1998”
611.102(b) “ASTM,”
“ASTM Method
D3859-03 A”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D3972-02”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D4107-98”
Board
Added the reference to the new method
62
611.102(b) “ASTM,”
“ASTM Method
D4327-97”
Board
Updated “D4327-91” to “D4327-97” and “October 15,
1991” to “1997”
611.102(b) “ASTM,”
“ASTM Method
D4327-03”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D4785-00a”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D5174-02”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D5317-93”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D5317-98”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D5673-05”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D6508-00(2005)e2”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D6919-03”
Board
Added the reference to the new method
611.102(b) “ASTM,”
“ASTM Method
D6888-04”
Board
Added the reference to the new method
611.102(b) “Bran &
Luebbe,” “Industrial
Method #129-71W”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(b) “Bran &
Luebbe,” “Technicon
Methods: Method
#380-75WE”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(b)
“Environmental
Resources Center”
Board
Added the source for and reference to the new method
611.102(b) “ERDA
Health and Safety
Laboratory,” “HASL
Procedure Manual”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
63
611.102(b) “Industrial
Test Systems, Inc.”
Board
Added the source for and reference to the new method
611.102(b) “NTIS,”
“Kaleda Automated
. . . Cyanide”
Board
Corrected “And” to loser-case “and”
611.102(b) “NTIS,”
“Technical Notes on
Drinking Water
Methods” Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition’ added information relating to
the on-line availability of the document
611.102(b) “Standard
Methods Online”
Board
Added the on-line source for and reference to the new
method
611.102(b) “USEPA,”
“OGWDW,” “Method
317.0”
Board
Changed “USEPA Method 317.0” to USEPA OGWDW
Methods, Method 317.0”
611.102(b) “USEPA,”
“OGWDW,” “Method
326.0”
Board
Changed “USEPA Method 326.0” to USEPA OGWDW
Methods, Method 326.0”
611.102(b) “USEPA,”
“OGWDW,” “Method
327.
Board
Changed “USEPA Method 327.0” to USEPA OGWDW
Methods, Method 327.0”; changed “Section 611.381” to
“Sections 611.381 and 611.531”
611.102(b) “USEPA,”
“OGWDW,” “Method
515.4”
Board
Changed “USEPA Method 515.4” to USEPA OGWDW
Methods, Method 515.4”
611.102(b) “USEPA,”
“OGWDW,” “Method
531.2”
Board
Changed “USEPA Method 531.2” to USEPA OGWDW
Methods, Method 531.2”
611.102(b) “USEPA,”
“OGWDW,” “Method
552.3”
Board
Changed “USEPA Method 552.3” to USEPA OGWDW
Methods, Method 552.3”; changed “Section 611.381” to
“Sections 611.381 and 611.645”
611.102(b) “USEPA,”
“OGWDW,” “Method
1622 (05)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
611.102(b) “USEPA,”
“OGWDW,” “Method
1622 (01)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
611.102(b) “USEPA,”
“OGWDW,” “Method
1622 (99)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
611.102(b) “USEPA,”
“OGWDW,” “Method
1623 (05)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
611.102(b) “USEPA,”
“OGWDW,” “Method
1623 (01)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
64
611.102(b) “USEPA,”
“OGWDW,” “Method
1623 (99)”
Board
Changed “USEPA Method 1622 (05)” to USEPA
OGWDW Methods, Method 1622 (05)”
611.102(b) “USEPA,”
“ORD,” “NERL,”
“USEPA Method
200.5”
Board
Added the reference to the new method
611.102(b) “Waters
Corporation”
Board
Added “or 508-482-2131, fax: 508-482-3625”
611.102(c), “40 CFR
3.2”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(c), “40 CFR
3.3”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(c), “40 CFR
3.10”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(c), “40 CFR
3.2000”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.102(c), “40 CFR
136.3(a)”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition to include March 12, 2007
amendments
611.102(c), “appendix
B to 40 CFR 136”
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350(b)
“maximum
permissible
concentration” Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350(b) “method
detection limit” Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350(b) “90th
percentile” Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350(b) “practical
quantitation limit”
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350(b) “small
system” Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.350 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.351(b)(3)(D)
Board
Removed the past effective date “as of July 12, 2001”
and the offsetting comma
611.351(e)(2)
Board
Added “the appropriate of” before “the following
timeframes”
65
611.351(e)(2)(A)
Board
Changed to capitalized “For”; changed the ending comma
to a semicolon; added the ending conjunction “or”
611.351(e)(2)(B)
Board
Changed to capitalized “For”
611.351 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.353 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.354(b)(1)
Board
Added “that is” before “required to commence”
611.354 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.355(a)(1) Board
note
Board
Removed the obsolete Board note
611.355(b)(2)
Board
Changed “do each of the following” to “complete the
public education tasks according to the following
requirements”
611.355(b)(4)
Board
Changed “it” to “a NTNCWS supplier”; changed “a
NTNCWS supplier” to “it”; changed “as follows” to “as
in . . . Section, subject to the limitation set forth in . . .
this Section”
611.355(b)(4)(A)
Board
Added “the NTNCWS supplier must”
611.355(b)(4)(B)
Board
Added “the NTNCWS supplier must”
611.355(b)(5)
Board
Changed “contained in” to “set forth in”
611.355 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.356(a)(1)
Board
Changed “sample site” to “sampling site”
611.356(a)(3)(A)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(3)(B)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(3)(C)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(3)(D)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(3)(E)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(A)(i)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(A)(ii)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(A)(iii)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
66
611.356(a)(4)(A)(iv)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(B)(i)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(B)(ii)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(B)(iii)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(A)(i)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(A)(ii)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(a)(4)(C)
Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(b)(5)(C)
Board
Changed “sample site” to “sampling site”
611.356(d)(4)(F)(ii)
Board note
Board
Added explanation of the movement of text to subsection
(d)(4)(H)
611.356(d)(4)(H)
Board note
Board
Added “(d)(4)(H) and”; added “the last sentence of 40
CFR 141.86(d)(4)(vi)(B) and”; updated the citation to the
Code of Federal Regulations
to the most recent edition
611.356(g)(6)(B)
Board
Changed “sample site” to “sampling site”
611.356 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.357(d)(1)
Board
Changed “State” to “Agency”
611.357(e)(2)(B)
Board
Changed “the following” to “that it has fulfilled the
conditions set forth in . . . this Section . . ., subject to the
conditions of . . . this Section”
611.357 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.358 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.359(a)(2)(C)
Board
Removed the unnecessary date from the citation to the
Code of Federal Regulations
, which is incorporated by
reference with a date in Section 611.102
611.359(a) Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.359(b) Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.359(c) Board
note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.360(a)(2)(A)
Board
Changed “sample site” to “sampling site”
67
611.360(a)(2)(B)
Board
Changed “sample sites” to “sampling sites”
611.360(e)(2)(C)
Board
Corrected “611.354(b)” to “611.354(c)”
611.360 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.381(b)(1)(B)(i)
Bard note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 6251, including explanation of USEPA approval
as an equivalent method
611.381(b)(1)(D)(i)
Board note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 4500-ClO
2
, including explanation of USEPA
approval as an equivalent method
611.381(c)(1) Board
note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 4500-Cl and Method 4500-ClO
2
, including
explanation of USEPA approval as an equivalent method
611.381(d)(3)(A)
Board note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 5310, including explanation of USEPA approval
as an equivalent method
611.381(d)(4)(A)
Board note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 5310, including explanation of USEPA approval
as an equivalent method
611.381(d)(4)(B)
Board note
Board
Added explanation of reference to
Standard Methods
,
21st edition instead of Standard Methods Online for
Method 5910, including explanation of USEPA approval
as an equivalent method
611.381 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.526 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.531(b)
Board
Removed “from Standard Methods . . . 18th and 19th
editions)”
611.531(b)(1)(A)
Board
Removed the colon and “Method 4500-Cl D”
611.531(b)(1)(A)(i)
Board
Added “Standard Methods, . . . Method 4500-Cl D”
611.531(b)(2)(A)
Board
Removed the colon and “Method 4500-Cl D”
611.531(b)(2)(A)(i)
Board
Added “Standard Methods, . . . Method 4500-Cl D”
611.531 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
68
611.600 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition (twice), including a
Federal
Register
citation for later amendments
611.611(a)
Board
Removed the obsolete parenthetical sentences “This
document also contains approved . . . until July 1, 1996.
These methods are not available for use after July 1,
1996.” even though it still appears in the corresponding
federal text
611.611(a)(3)(A)
Board
Corrected “D2460-90” to “D2460-97”
611.611(a)(8)(D)
Board
Corrected “ASTM D6919-03” to “ASTM Method
D6919-03”
611.611(a)(15)(B)(ii)
Board
Added the entry for “3500-Mg B” from the 20th edition
of
Standard Methods
611.611(a)(15)(B)(iii) Board
Moved the entry for “3500-Mg B” from the 20th edition
of
Standard Methods
to subsection (a)(15)(B)(ii)
611.611(a)(21)
Board
Changed “pH” to “pH: Electrometric”
611.611(a)(21)(A)
Board
Moved “electrometric” to subsection (a)(21) and
removed the old subsection; renumbered old subsection
(a)(21)(A)(i) to subsection (a)(21)(A); added “USEPA
Inorganic Methods, Method 150.2”
611.611(a)(21)(B)
Board
Moved “USEPA Inorganic Methods: Method 150.2” to
renumbered subsection (a)(21)(A) and removed old
subsection (a)(21)(B)
611.611(a)(23)(C)
Board
Corrected “D859-95” to “D859-94”
611.611 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.612(f)(2)(A)(i)
Board
Added citation to the 21st edition of
Standard Methods
based on March 12,
611.612 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition (twice), including a
Federal
Register
citation for later amendments
611.645 preamble
Board
Added the formerly omitted sentence from 40 C.F.R.
141.24(e) relating to
Technical Notes on Drinking Water
Methods
, including incorporation of the USEPA guidance
by reference
611.645 “2,4-D”
Board
Added “OGWDW Methods, Method” before “515.4”
611.645 “2,4,5-TP
(Silvex)”
Board
Added “OGWDW Methods, Method” before “515.4”
611.645 “alachlor”
Board
Changed the asterisk to the numeric footnote designation
“
1
”
611.645 “atrazine”
Board
Changed the asterisk to the numeric footnote designation
“
1
”
611.645 “carbofuran”
Board
Added “OGWDW Methods, Method” before “531.2”
69
611.645 “dalapon”
Board
Added “OGWDW Methods, Method” before “515.4”;
added “OGWDW Methods, Method” before “552.3”
611.645 “dinoseb”
Board
Added “OGWDW Methods, Method” before “515.4”
611.645 “dalapon”
Board
Added “OGWDW Methods, Method” before “531.2”
611.645 “pentachloro-
phenol”
Board
Added “OGWDW Methods, Method” before “515.4”
611.645 “simazine”
Board
Changed the asterisk to the numeric footnote designation
“
1
”
611.645 note 1
Board
Changed the asterisk to the numeric footnote designation
“
1
”
611.645 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.720(a)(3)(A)(i)
Board
Changed “D2460-90” to “D2460-97”
711.720(c)(1)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
711.720(c)(2)
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition
611.720 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.802 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.884 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.1004(a)
Board
Added “OGWDW Methods,” before “Method 1623”;
added “OGWDW Methods,” before “Method 1622”
611.1004 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
611.1007(c)(1)(A)
Board
Added “OGWDW Methods,” before “Method 1623”
611.1007(c)(1)(B)
Board
Added “OGWDW Methods,” before “Method 1622”
611.1007(c)(1)(C)
Board
Added “OGWDW Methods,” before “Method 1623”
611.1007(c)(1)(D)
Board
Added “OGWDW Methods,” before “Method 1622”
611.1007(c)(1)(E)
Board
Added “OGWDW Methods,” before “Method 1623”
611.1007(c)(1)(F)
Board
Added “OGWDW Methods,” before “Method 1622”
611.1007 Board note
Board
Updated the citation to the
Code of Federal Regulations
to the most recent edition, including a
Federal Register
citation for later amendments
70
I, John T. Therriault, Assistant Clerk of the Illinois Pollution Control Board, certify that
the Board adopted the above opinion on August 7, 2008, by a vote of 4-0.
____________________________________
John T. Therriault, Assistant Clerk
Illinois Pollution Control Board