TITLE 35: ENVIRONMENTAL PROTECTION

SUBTITLE G: WASTE DISPOSAL

CHAPTER I: POLLUTION CONTROL BOARD

SUBCHAPTER c: HAZARDOUS WASTE OPERATING REQUIREMENTS

PART 728

LAND DISPOSAL RESTRICTIONS

SUBPART A: GENERAL

Section

728.101

728.102

728.103

728.104

728.105

728.106

Purpose, Scope, and Applicability

Definitions

Dilution Prohibited as a Substitute for Treatment

Treatment Surface Impoundment Exemption

Procedures for Case-by-Case Extensions to an Effective Date

Petitions to Allow Land Disposal of a Waste Prohibited undcrPursuant

to Subpart C

?

728.107

?

Testing, Tracking, and Recordkeeping Requirements for Generators,

Treaters, and Disposal Facilities

?

728.108?

Landfill and Surface Impoundment Disposal Restrictions (Repealed)

?

728.109?

Special Rules for Characteristic Wastes

SUBPART B: SCHEDULE FOR LAND DISPOSAL PROHIBITION AND ESTABLISHMENT OF

TREATMENT STANDARDS

Section

728.110

728.111

728.112

728.113

728.114

SUBPART C:

First Third (Repealed)

Second Third (Repealed)

Third Third (Repealed)

Newly Listed Wastes

Surface Impoundment Exemptions

PROHIBITION ON LAND DISPOSAL

Section

?

728.120?

Waste-Specific Prohibitions: Dyes and Pigments Production Wastes

?

728.130

?

Waste-Specific Prohibitions: Wood Preserving Wastes

?

728.131

?

Waste-Specific Prohibitions: Dioxin-Containing Wastes

?

728.132

?

Waste-Specific Prohibitions: Soils Exhibiting the Toxicity

Characteristic for Metals and Containing PCBs

728.133

Waste-Specific

Prohibitions:

Chlorinated Aliphatic Wastes

728.134

Waste-Specific

Prohibitions: Toxicity Characteristic Metal Wastes

728.135

Waste-Specific

Prohibitions:

Petroleum Refining Wastes

728.136

Waste-Specific

Prohibitions: Inorganic Chemical Wastes

728.137

Waste-Specific

Prohibitions: Ignitable and Corrosive Characteristic

Wastes Whose Treatment Standards Were Vacated

?

728.138?

Waste-Specific Prohibitions: Newly-Identified Organic Toxicity

Characteristic Wastes and Newly-Listed Coke By-Product and Chlorotoluene

Production Wastes

?

728.139?

Waste-Specific Prohibitions: Spent Aluminum Potliners and Carbamate

Wastes

SUBPART D: TREATMENT STANDARDS

Section

728.140

?

Applicability of Treatment Standards

---

728.141

728.142

728.143

728.144

728.145

728.146

728.148

728.149

Treatment Standards Expressed as Concentrations in Waste Extract

Treatment Standards Expressed as Specified Technologies

Treatment Standards Expressed as Waste Concentrations

Adjustment of Treatment Standard

Treatment Standards for Hazardous Debris

Alternative Treatment Standards Based on HTMR

Universal Treatment Standards

Alternative LDR Treatment Standards for Contaminated Soil

SUBPART E: PROHIBITIONS ON STORAGE

Section

?

728.150

?

Prohibitions on Storage of Restricted Wastes

?

728.?

?

ke

A Toxicity Characteristic Leaching Procedure (TCLP)

(Repealed)

728.Append-i-xAPPENDIX B Treatment Standards (As concentrations in the Treatment

Residual Extract) (Repealed)

728.ApperldxAPPENDIX C List of Halogenated Organic Compounds Regulated under

Section 728.132

728.Append-i-HAPPENDIX D Wastes Excluded from Lab Packs

728.AppcndixAPPENDIX E Organic Lab Packs (Repealed)

728.Append-iHAPPENDIX F Technologies to Achieve Deactivation of Characteristics

728.Append-i-HAPPENDIX G Federal Effective Dates

728.Append-i-xAPPENDIX H National Capacity LDR Variances for UIC Wastes

728.Append-i-xAPPENDIX I EP Toxicity Test Method and Structural Integrity Test

728.Aplaend-i-HAPPENDIX J Recordkeeping, Notification, and Certification

Requirements (Repealed)

728.Append,tHAPPENDIX K Metal-Bearing Wastes Prohibited from Dilution in a

Combustion Unit According to Section 728.103(c)

728.Tab1oTABLE A Constituent Concentrations in Waste Extract (CCWE)

728.Tab1oTABLE B Constituent Concentrations in Wastes (CCW)

728.Tab1oTABLE C Technology Codes and Description of Technology-Based Standards

728.Tab1oTABLE D Technology-Based Standards by RCRA Waste Code

728.Tab1oTABLE E Standards for Radioactive Mixed Waste

728.Tab1oTABL F Alternative Treatment Standards for Hazardous Debris

728.Tab1oTABLE G Alternative Treatment Standards Based on HTMR

728.Tab1oTABLE H Wastes Excluded from CCW Treatment Standards

728.TabloTABLE I Generator Paperwork Requirements

728.TablcTABLE T Treatment Standards for Hazardous Wastes

728.TabloTABLE U Universal Treatment Standards (UTS)

AUTHORITY: Implementing Sections 7.2 and 22.4 and authorized by Section 27 of

the Environmental Protection Act [415 ILCS 5/7.2, 22.4, and 27].

SOURCE: Adopted in R87-5 at 11 Ill. Reg. 19354, effective Nov.November 12,

1987; amended in R87-39 at 12 Ill. Reg. 13046, effective July 29, 1988; amended

in R89-1 at 13 Ill. Reg. 18403, effective Nov.November 13, 1989; amended in R89-

9 at 14 Ill. Reg. 6232, effective April 16, 1990; amended in R90-2 at 14 Ill.

Reg. 14470, effective August 22, 1990; amended in R90-10 at 14 Ill. Reg. 16508,

effective Scpt.,September 25, 1990; amended in R90-11 at 15 Ill. Reg. 9462,

effective June 17, 1991; amended in R90-11 at 15 Ill. Reg. 11937, effective

August 12, 1991; amendment withdrawn at 15 Ill. Reg. 14716, October 11, 1991;

amended in R91-13 at 16 Ill. Reg. 9619, effective June 9, 1992; amended in R92-

10 at 17 Ill. Reg. 5727, effective March 26, 1993; amended in R93-4 at 17 Ill.

Reg. 20692, effective Nov.November 22, 1993; amended in R93-16 at 18 Ill. Reg.

6799, effective April 26, 1994; amended in R94-7 at 18 Ill. Reg. 12203,

---

effective July 29, 1994; amended in R94-17 at 18 Ill. Reg. 17563, effective

Nov November 23, 1994; amended in R95-6 at 19 Ill. Reg. 9660, effective June 27,

1995; amended in R95-20 at 20 Ill. Reg. 11100, effective August 1, 1996; amended

in R96-10/R97-3/R97-5 at 22 Ill. Reg. 783, effective December 16, 1997; amended

in R98-12 at 22 Ill. Reg. 7685, effective April 15, 1998; amended in R97-21/R98-

3/R98-5 at 22 Ill. Reg. 17706, effective Scpt.September 28, 1998; amended in

R98-21/R99-2/R99-7 at 23 Ill. Reg. 1964, effective January 19, 1999; amended in

R99-15 at 23 Ill. Reg. 9204, effective July 26, 1999; amended in R00-13 at 24

Ill. Reg. 9623, effective June 20, 2000; amended in R01-3 at 25 Ill. Reg. 1296,

effective January 11, 2001; amended in R01-21/R01-23 at 25 Ill. Reg. 9181,

effective July 9, 2001; amended in R02-1/R02-12/R02-17 at 26 Ill. Reg. 6687,

effective April 22, 2002; amended in R03-18 at 27 Ill. Reg. 13045, effective

July 17, 2003; amended in R05-8 at 29 Ill. Reg. 6049, effective April 13, 2005;

amended in R06-5/R06-6/R06-7 at 30 In. Reg. 3800, effective February 23, 2006;

amended in R07 5/R07 7506-16/R06-17/R06-18 at 323

.

1

?

Reg ?

1254, effective

, effective

SUBPART A: GENERAL

Section 728.102?

Definitions

When used in this Part, the following terms have the meanings given below. All

other terms have the meanings given under 35 Ill. Adm. Code 702.110, 720.110, or

721.102 through 721.104.

"Agency" means the Illinois Environmental Protection Agency.

"Board" means the Illinois Pollution Control Board.

"CERCLA" means the Comprehensive Environmental Response, Compensation, and

Liability Act of 1980 (42 USC 9601 et seq.)

"Debris" means solid material exceeding a 60 mm particle size that is intended

for disposal and that is. is a manufactured object; plant or animal matter; or

natural geologic material. However, the following materials are not debris:

any material for which a specific treatment standard is provided in Subpart D of

this Part, namely lead acid batteries, cadmium batteries, and radioactive lead

solids; process residuals, such as smelter slag and residues from the treatment

of waste, wastewater, sludges, or air emission residues; and intact containers

of hazardous waste that are not ruptured and that retain at least 75 percent of

their original volume. A mixture of debris that has not been treated to the

standards provided by Section 728.145 of this Part and other material is subject

to regulation as debris if the mixture is comprised primarily of debris, by

volume, based on visual inspection.

"End of pipe" refers to thc point where effluent is discharged to thc

cnvironmcnt.

"Halogenated organic compounds" or "HOCs" means those compounds having a carbon-

halogen bond that are listed under Appendix C of this Part.

"Hazardous constituent or constituents" means those constituents listed in

Appendix H to 35 Ill. Adm. Code 721.

I-

-u p -

I,.

Zs

ZI

---

"Hazardous debris" means debris that contains a hazardous waste listed in

Subpart D of 35 Ill. Adm. Code 721 or that exhibits a characteristic of

hazardous waste identified in Subpart C of 35 Ill. Adm. Code 721. Any

deliberate mixing of prohibited waste with debris that changes its treatment

classification (i.e., from waste to hazardous debris) is not allowed under the

dilution prohibition in Section 728.103.

"Inorganic metal-bearing waste" is one for which USEPA has established treatment

standards for metal hazardous constituents that does not otherwise contain

significant organic or cyanide content, as described in Section 728.103(b)(1),

and which is specifically listed in Appendix K of this Part.

"Land disposal" means placement in or on the land, except in a corrective action

management unit or staging pile, and "land disposal" includes, but is not

limited to, placement in a landfill, surface impoundment, waste pile, injection

well, land treatment facility, salt dome formation, salt bed formation,

underground mine or cave, or placement in a concrete vault or bunker intended

for disposal purposes.

"Land disposal restriction" or "LDR" is a restriction imposed on the land

disposal of a hazardous waste pursuant to this Part or 40 CFR 738. The land

disposal of hazardous waste is generally prohibited, except where the activity

constituting land disposal is specfically allowed, pursuant to this Part or 40

CFR 738.

BOARD NOTE: The Board added this definition based on the preamble discussions

at 51 Fed. Reg. 40572, 40573-74 (Nov.November 7, 1986) and 53 Fed. Reg. 28118,

28119-20 (July 26, 1988). The USEPA publication "Terms of Environment Glossary,

Abbreviations, and Acronyms" (December 1997), USEPA, Communications, Education,

and Public Affairs, EPA 175/B-97-001, defines "land disposal restrictions" as

follows: "Rules that require hazardous wastes to be treated before disposal on

land to destroy or immobilize hazardous constituents that might migrate into

soil and ground water."

"Nonwastewaters" are wastes that do not meet the criteria for "wastewaters" in

this Section.

"Polychlorinated biphenyls" or "PCBs" are halogenated organic compounds defined

in accordance with federal 40 CFR 761.3 (Definitions), incorporated by reference

in 35 Ill. Adm. Code 720.111(b).

"ppm" means parts per million.

"RCRA corrective action" means corrective action taken under 35 Ill. Adm. Code

724.200 or 725.193, federal 40 CFR 264.100 or 265.93, or similar regulations in

other states with RCRA programs authorized by USEPA pursuant to 40 CFR 271.

"Soil" means unconsolidated earth material composing the superficial geologic

strata (material overlying bedrock), consisting of clay, silt, sand, or gravel

size particles, as classified by the United States Natural Resources

Conservation Service, or a mixture of such materials with liquids, sludges, or

solids that is inseparable by simple mechanical removal processes and which is

made up primarily of soil by volume based on visual inspection. Any deliberate

mixing of prohibited waste with debris that changes its treatment classification

(i.e., from waste to hazardous debris) is not allowed under the dilution

prohibition in Section 728.103.

---

"Underlying hazardous constituent" means any constituent listed in Table U of

this Part, "Universal Treatment Standards (UTS)," except fluoride, selenium,

sulfides, vanadium, and zinc, that can reasonably be expected to be present at

the point of generation of the hazardous waste at a concentration above the

constituent-specific UTS treatment standard.

"USEPA" or "U.S. EPA" means the United States Environmental Protection Agency.

"Wastewaters" are wastes that contain less than one percent by weight total

organic carbon (TOC) and less than one percent by weight total suspended solids

(TSS).

Section

(Source:

728.104Amended

?

at

Treatment

32 Ill. Reg.Surface

Impoundment

—, effective

Exemption

?

a)

?

Wastes that are otherwise prohibited from land disposal under this Part

may be treated in a surface impoundment or series of impoundments provided that

all of the following conditions are fulfilled:

1)?

Treatment of such wastes occurs in the impoundments;

2)?

The following conditions are met:

A)

Sampling and testing. For wastes with treatment standards in Subpart D or

prohibition levels in Subpart C, the residues from treatment are analyzed, as

specified in Section 728.107 or 728.132, to determine if they meet the

applicable treatment standards or, where no treatment standards have been

established for the waste, the applicable prohibition levels. The sampling

method, specified in the waste analysis plan under 35 Ill. Adm. Code 724.113 or

725.113, must be designed such that representative samples of the sludge and the

supernatant are tested separately rather than mixed to form homogeneous samples.

B)

Removal. The following treatment residues (including any liquid waste)

must be removed at least annually: residues that do not meet the treatment

standards promulgated under Subpart D of this Part; residues that do not meet

the prohibition levels established under Subpart C of this Part or imposed by

federal statute (where no treatment standards have been established); residues

that are from the treatment of wastes prohibited from land disposal under

Subpart C of this Part (where no treatment standards have been established and

no prohibition levels apply); or residues from managing listed wastes that are

not delisted under 35 Ill. Adm. Code 720.122.

?

If the volume of liquid flowing

through the impoundment or series of impoundments annually is greater than the

volume of the impoundment or impoundments, this flow-through constitutes removal

of the supernatant for the purpose of this requirement.

C)

Subsequent management. Treatment residues must not be placed in any other

surface impoundment for subsequent management.

D)

Recordkeeping. Sampling, testing, and recordkeeping provisions of 35 Ill.

Adm. Code 724.113 or 725.113 apply;

3)?

The impoundment meets the design requirements of 35 Ill. Adm. Code

724.321(c) or 725.321(a) even though the unit may not be new, expanded or a

---

replacement, and must be in compliance with applicable groundwater monitoring

requirements of Subpart F of 35 Ill. Adm. Code 724 or Subpart F of this Part 35

Ill. Adm. Code 725, unless any of the following conditions is fulfilled:

A)?

The impoundment is exempted pursuant to 35 Ill. Adm. Code 724.321(d) or

(e), or to 35 Ill. Adm. Code 725.321(c) or (d);

B)?

Upon application by the owner or operator, the Agency has by permit

provided that the requirements of this Part do not apply on the basis that the

surface impoundment fulfills all of the following conditions:

i)

The impoundment has at least one liner, for which there is no evidence

that such liner is leaking;

ii)

The impoundment is located more than one-quarter mile from an underground

source of drinking water; and

iii)

The impoundment is in compliance with generally applicable groundwater

monitoring requirements for facilities with permits; or

C)?

Upon application by the owner or operator, the Board has, pursuant to

Subpart D of 35 Ill. Adm. Code 104, granted an adjusted standard from the

requirements of this Part. The justification for such an adjusted standard must

be a demonstration that the surface impoundment is located, designed, and

operated so as to assure that there will be no migration of any hazardous

constituent into groundwater or surface water at any future time; and

4)?

The owner or operator submits to the Agency a written certification that

the requirements of subsection (a)(3) of this Section have been met. The

following certification is required:

I certify under penalty of law that the requirements of 35 Ill. Adm. Code

728.104(a) (3) have been met for all surface impoundments being used to treat

restricted wastes. I believe that the submitted information is true, accurate,

and complete. I am aware that there are significant penalties for submitting

false information, including the possibility of fine and imprisonment.

b)

?

Evaporation of hazardous constituents as the principal means of treatment

is not considered to be a treatment for purposes of an exemption under this

Section.

Section

(Source:

728.107Amended ?

at

Testing,

32 Ill. Reg.Tracking,

and

?

,

Recordkeeping

effective ?

Requirements for

Generators, Treaters, and Disposal Facilities

a)?

Requirements for generators.

1)

?

A generator of a hazardous waste must determine if the waste has to be

treated before it can be land disposed. This is done by determining if the

hazardous waste meets the treatment standards in Section 728.140, 728.145, or

728.149. This determination can be made concurrently with the hazardous waste

determination required in 35 Ill. Adm. Code 722.111, in either of two ways:

testing the waste or using knowledge of the waste. If the generator tests the

waste, testing determines the total concentration of hazardous constituents or

the concentration of hazardous constituents in an extract of the waste obtained

using Method 1311 (Toxicity Characteristic Leaching Procedure) in "Test Methods

---

for Evaluating Solid Waste, Physical/Chemical Methods," USEPA publication number

EPA-530/SW-846, incorporated by reference in 35 Ill. Adm. Code 720.111(a),

depending on whether the treatment standard for the waste is expressed as a

total concentration or concentration of hazardous constituent in the waste

extract. (Alternatively, the generator must send the waste to a RCRA-permitted

hazardous waste treatment facility, where the waste treatment facility must

comply with the requirements of 35 Ill. Adm. Code 724.113 and subsection (b) of

this Section.) In addition, some hazardous wastes must be treated by particular

treatment methods before they can be land disposed and some soils are

contaminated by such hazardous wastes. These treatment standards are also found

in Section 728.140 and Table T of this Part, and are described in detail in

Table C of this Part. These wastes and soils contaminated with such wastes do

not need to be tested (however, if they are in a waste mixture, other wastes

with concentration level treatment standards must be tested). If a generator

determines that it is managing a waste or soil contaminated with a waste that

displays a hazardous characteristic of ignitability, corrosivity, reactivity, or

toxicity, the generator must comply with the special requirements of Section

728.109 in addition to any applicable requirements in this Section.

2)?

If the waste or contaminated soil does not meet the treatment standard or

if the generator chooses not to make the determination of whether its waste must

be treated, the generator must send a one-time written notice to each treatment

or storage facility receiving the waste with the initial shipment of waste to

each treatment or storage facility, and the generator must place a copy of the

one-time notice in the file. The notice must include the information in column

"728.107(a) (2)" of the Generator Paperwork Requirements Table in Table I of this

Part. (Alternatively, if the generator chooses not to make the determination of

whether the waste must be treated, the notification must include the USEPA

hazardous waste numbers and manifest number of the first shipment, and it must

include the following statement: "This hazardous waste may or may not be

subject to the LDR treatment standards. The treatment facility must make the

determination.") No further notification is necessary until such time that the

waste or facility changes, in which case a new notification must be sent and a

copy placed in the generator's file.

A)

included, signed by an authorized representative:

I ccrtify undcr penalty of law that I personally have examined this contaminated

is marked "reserved" by USEPA. This statement maintains structural c nsistency

with USEPA rules.

3)

?

If the waste or contaminated soil meets the treatment standard at the

original point of generation, the waste generator must do the following:

A)?

With the initial shipment of waste to each treatment, storage, or disposal

facility, the generator must send a one-time written notice to each treatment,

storage, or disposal facility receiving the waste, and place a copy in its own

file. The notice must include the information indicated in column

---

"728.107(a)(3)" of the Generator Paperwork Requirements Table in Table I of this

Part and the following certification statement, signed by an authorized

representative:

I certify under penalty of law that I personally have examined and am familiar

with the waste through analysis and testing or through knowledge of the waste to

support this certification that the waste complies with the treatment standards

specified in Subpart D of 35 Ill. Adm. Code 728. I believe that the information

I submitted is true, accurate, and complete. I am aware that there are

significant penalties for submitting a false certification, including the

possibility of a fine and imprisonment.

B)

For contaminated soil, with the initial shipment of wastes to each

treatment, storage, or disposal facility, the generator must send a one-time

written notice to each facility receiving the waste and place a copy in the

file. The notice must include the information in the column headed "(a)(3)" in

Table I of this Part.

C)

If the waste changes, the generator must send a new notice and

certification to the receiving facility and place a copy in its files. A

generator of hazardous debris excluded from the definition of hazardous waste

under 35 Ill. Adm. Code 721.103(f) is not subject to these requirements.

4)

For reporting, tracking and recordkeeping when exceptions allow certain

wastes or contaminated soil that do not meet the treatment standards to be land

disposed, there are certain exemptions from the requirement that hazardous

wastes or contaminated soil meet treatment standards before they can be land

disposed. These include, but are not limited to, case-by-case extensions under

Section 728.105, disposal in a no-migration unit under Section 728.106, or a

national capacity variance or case-by-case capacity variance under Subpart C of

this Part. If a generator's waste is so exempt, then with the initial shipment

of waste, the generator must send a one-time written notice to each land

disposal facility receiving the waste. The notice must include the information

indicated in column "728.107(a) (4)" of the Generator Paperwork Requirements

Table in Table I of this Part. If the waste changes, the generator must send a

new notice to the receiving facility, and place a copy in its file.

5)

If a generator is managing and treating prohibited waste or contaminated

soil in tanks, containers, or containment buildings regulated under 35 Ill. Adm.

Code 722.134 to meet applicable LDR treatment standards found at Section

728.140, the generator must develop and follow a written waste analysis plan

that describes the procedures it will carry out to comply with the treatment

standards. (Generators treating hazardous debris under the alternative

treatment standards of Table F of this Part, however, are not subject to these

waste analysis requirements.) The plan must be kept on site in the generator's

records, and the following requirements must be met:

A)

The waste analysis plan must be based on a detailed chemical and physical

analysis of a representative sample of the prohibited wastes being treated, and

contain all information necessary to treat the wastes in accordance with the

requirements of this Part, including the selected testing frequency;

B)

Such plan must be kept in the facility's on-site files and made available

to inspectors; and

---

C)?

Wastes shipped off-site pursuant to this subsection (a)(5) of this Section

must comply with the notification requirements of subsection (a)(3) of this

Section.

6)

If a generator determines that the waste or contaminated soil is

restricted based solely on its knowledge of the waste, all supporting data used

to make this determination must be retained on-site in the generator's files.

If a generator determines that the waste is restricted based on testing this

waste or an extract developed using Method 1311 (Toxicity Characteristic

Leaching Procedure) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846, all waste

analysis data must be retained on-site in the generator's files.

7) If a generator determines that it is managing a prohibited waste that is

excluded from the definition of hazardous or solid waste or which is exempt from

Subtitle C regulation under 35 Ill. Adm. Code 721.102 through 721.106 subsequent

to the point of generation (including deactivated characteristic hazardous

wastes that are managed in wastewater treatment systems subject to the CWA, as

specified at 35 Ill. Adm. Code 721.104(a)(2); that are CWA-equivalent; or that

are managed in an underground injection well regulated under 35 Ill. Adm. Code

730), the generator must place a one-time notice stating such generation,

subsequent exclusion from the definition of hazardous or solid waste or

exemption from RCRA Subtitle C regulation, and the disposition of the waste in

the generating facility's on-site file.

8)

A generator must retain a copy of all notices, certifications, waste

analysis data, and other documentation produced pursuant to this Section on-site

for at least three years from the date that the waste that is the subject of

such documentation was last sent to on-site or off-site treatment, storage, or

disposal. The three-year record retention period is automatically extended

during the course of any unresolved enforcement action regarding the regulated

activity or as requested by the Agency. The requirements of this subsection

(a) (8) apply to solid wastes even when the hazardous characteristic is removed

prior to disposal, or when the waste is excluded from the definition of

hazardous or solid waste under 35 Ill. Adm. Code 721.102 through 721.106, or

exempted from RCRA Subtitle C regulation, subsequent to the point of generation.

9)

If a generator is managing a lab pack containing hazardous wastes and

wishes to use the alternative treatment standard for lab packs found at Section

728.142(c), the generator must fulfill the following conditions:

A)?

With the initial shipment of waste to a treatment facility, the generator

must submit a notice that provides the information in column "Section

728.107(a)(9)" in the Generator Paperwork Requirements Table of Table I of this

Part and the following certification. The certification, which must be signed

by an authorized representative and must be placed in the generator's files,

must say the following:

I certify under penalty of law that I personally have examined and am familiar

with the waste and that the lab pack contains only wastes that have not been

excluded under Appendix D to 35 Ill. Adm. Code 728 and that this lab pack will

be sent to a combustion facility in compliance with the alternative treatment

standards for lab packs at 35 Ill. Adm. Code 728.142(c). I am aware that there

are significant penalties for submitting a false certification, including the

possibility of fine or imprisonment.

---

.,

B)

No further notification is necessary until such time as the wastes in the

lab pack change, or the receiving facility changes, in which case a new notice

and certification must be sent and a copy placed in the generator's file.

C)

If the lab pack contains characteristic hazardous wastes (D001-D043),

underlying hazardous constituents (as defined in Section 728.102(i)) need not be

determined.

D) The generator must also comply with the requirements in subsections (a)(6)

and (a)(7) of this Section.

10) Small quantity generators with tolling agreements pursuant to 35 Ill. Adm.

Code 722.120(e) must comply with the applicable notification and certification

requirements of subsection (a) of this Section for the initial shipment of the

waste subject to the agreement. Such generators must retain on-site a copy of

the notification and certification, together with the tolling agreement, for at

least three years after termination or expiration of the agreement. The three-

year record retention period is automatically extended during the course of any

unresolved enforcement action regarding the regulated activity or as requested

by the Agency.

b)?

The owner or operator of a treatment facility must test its wastes

according to the frequency specified in its waste analysis plan, as required by

35 Ill. Adm. Code 724.113 (for permitted TSDs) or 725.113 (for interim status

facilities). Such testing must be performed as provided in subsections (b)(1),

(b)(2), and (b)(3) of this Section.

1)

For wastes or contaminated soil with treatment standards expressed in the

waste extract (TCLP), the owner or operator of the treatment facility must test

an extract of the treatment residues using Method 1311 (Toxicity Characteristic

Leaching Procedure) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846, to assure

that the treatment residues extract meets the applicable treatment standards.

2)

For wastes or contaminated soil with treatment standards expressed as

concentrations in the waste, the owner or operator of the treatment facility

must test the treatment residues (not an extract of such residues) to assure

that the treatment residues meet the applicable treatment standards.

3)

A one-time notice must be sent with the initial shipment of waste or

contaminated soil to the land disposal facility. A copy of the notice must be

placed in the treatment facility's file.

A)

No further notification is necessary until such time that the waste or

receiving facility changes, in which case a new notice must be sent and a copy

placed in the treatment facility's file.

B)

The one-time notice must include the following requirements :

i) USEPA hazardous waste number and manifest number of first shipment;

ii)

The waste is subject to the LDRs. The constituents of concern for F001

through F005 and F039 waste and underlying hazardous constituents in

characteristic wastes, unless the waste will be treated and monitored for all

constituents. If all constituents will be treated and monitored, there is no

need to put them all on the LDR notice;

---

iii)

The notice must include the applicable wastewater/ nonwastewater category

(see Section 728.102(d) and (f)) and subdivisions made within a waste code based

on waste-specific criteria (such as D003 reactive cyanide);

iv)

Waste analysis data (when available);

v)

For contaminated soil subject to LDRs as provided in Section 728.149(a),

the constituents subject to treatment as described in Section 728.149(d) and the

following statement, "this contaminated soil (does/does not) contain listed

hazardous waste and (does/does not) exhibit a characteristic of hazardous waste

and (is subject to/complies with) the soil treatment standards as provided by

Section 728.149(c)"; and

vi)

A certification is needed (see applicable Section for exact wording).

4)?

The owner or operator of a treatment facility must submit a certification

signed by an authorized representative with the initial shipment of waste or

treatment residue of a restricted waste to the land disposal facility.

?

The

certification must state as follows:

I certify under penalty of law that I have personally examined and am

familiar with the treatment technology and operation of the treatment process

used to support this certification. Based on my inquiry of those individuals

immediately responsible for obtaining this information, I believe that the

treatment process has been operated and maintained properly so as to comply with

the treatment standards specified in 35 Ill. Adm. Code 728.140 without

impermissible dilution of the prohibited waste. I am aware there are

significant penalties for submitting a false certification, including the

possibility of fine and imprisonment.

A certification is also necessary for contaminated soil and it must state

as follows:

I certify under penalty of law that I have personally examined and am

familiar with the treatment technology and operation of the treatment process

used to support this certification and believe that it has been maintained and

operated properly so as to comply with treatment standards specified in 35 Ill.

Adm. Code 728.149 without impermissible dilution of the prohibited wastes. I am

aware there are significant penalties for submitting a false certification,

including the possibility of fine and imprisonment.

A)

A copy of the certification must be placed in the treatment facility's on-

site files. If the waste or treatment residue changes, or the receiving

facility changes, a new certification must be sent to the receiving facility,

and a copy placed in the treatment facility's file.

B)

Debris excluded from the definition of hazardous waste under 35 Ill. Adm.

Code 721.103(c) 721.103(f) (i.e., debris treated by an extraction or destruction

technology listed in Table F of this Part and debris that the Agency has

determined does not contain hazardous waste) is subject to the notification and

certification requirements of subsection (d) of this Section rather than the

certification requirements of this subsection (b)(4).

C)

For wastes with organic constituents having treatment standards expressed

as concentration levels, if compliance with the treatment standards is based in

part or in whole on the analytical detection limit alternative specified in

---

Section 728.140(d), the certification must be signed by an authorized

representative and must state as follows:

I certify under penalty of law that I have personally examined and am

familiar with the treatment technology and operation of the treatment process

used to support this certification. Based on my inquiry of those individuals

immediately responsible for obtaining this information, I believe that the

nonwastewater organic constituents have been treated by combustion units as

specified in Table C to 35 Ill. Adm. Code 728. I have been unable to detect the

nonwastewater organic constituents, despite having used best good faith efforts

to analyze for such constituents. I am aware that there are significant

penalties for submitting a false certification, including the possibility of

fine and imprisonment.

D)

For characteristic wastes that are subject to the treatment standards in

Section 728.140 and Table T of this Part (other than those expressed as a

required method of treatment) or Section 728.149 and which contain underlying

hazardous constituents, as defined in Section 728.102(i); if these wastes are

treated on-site to remove the hazardous characteristic; and that are then sent

off-site for treatment of underlying hazardous constituents, the certification

must state as follows:

I certify under penalty of law that the waste has been treated in

accordance with the requirements of 35 Ill. Adm. Code 728.140 and Table T of

Section 728.149 of that Part to remove the hazardous characteristic. This

decharacterized waste contains underlying hazardous constituents that require

further treatment to meet treatment standards. I am aware that there are

significant penalties for submitting a false certification, including the

possibility of fine and imprisonment.

E)

For characteristic wastes that contain underlying hazardous constituents,

as defined in Section 728.102(i), that are treated on-site to remove the

hazardous characteristic and to treat underlying hazardous constituents to

levels in Section 728.148 and Table U of this Part universal treatment

standards, the certification must state as follows:

I certify under penalty of law that the waste has been treated in

accordance with the requirements of 35 Ill. Adm. Code 728.140 and Table T of

that Part to remove the hazardous characteristic and that underlying hazardous

constituents, as defined in 35 Ill. Adm. Code 728.102(i), have been treated on-

site to meet the universal treatment standards of 35 Ill. Adm. Code 728.148 and

Table U of that Part. I am aware that there are significant penalties for

submitting a false certification, including the possibility of fine and

imprisonment.

5)

If the waste or treatment residue will be further managed at a different

treatment, storage, or disposal facility, the treatment, storage, or disposal

facility that sends the waste or treatment residue off-site must comply with the

notice and certification requirements applicable to generators under this

Section.

6)

Where the wastes are recyclable materials used in a manner constituting

disposal subject to the provisions of 35 Ill. Adm. Code 726.120(b), regarding

treatment standards and prohibition levels, the owner or operator of a treatment

facility (i.e., the recycler)

?

civing facility

wastes the owner or operator of the recycling facility must submit must, for the

---

initial shipment of waste, prepare a one-time certification described in

subsection (b)(4) of this Section and a notice that includes the information

listed in subsection (b) (3) of this Section (except the manifest number) to the

Agency. The certification and notification must be placed in the facility's on-

site files. If the waste or the receiving facility changes, a new certification

and notification must be prepared and placed in the on-site files. The In

addition, the owner or operator of the recycling facility also must keep records

of the name and location of each entity receiving the hazardous waste-derived

product.

c)?

Except where the owner or operator is disposing of any waste that is a

recyclable material used in a manner constituting disposal pursuant to 35 Ill.

Adm. Code 726.120(b), the owner or operator of any land disposal facility

disposing any waste subject to restrictions under this Part must do the

following:

1)

Maintain in its files copies of the notice and certifications specified in

subsection (a) or (b) of this Section.

2)

Test the waste or an extract of the waste or treatment residue developed

using Method 1311 (Toxicity Characteristic Leaching Procedure4- in "Test Methods

for Evaluating Solid Waste, Physical/Chemical Methods," USEPA publication number

EPA-530/SW-846,846) to assure that the waste or treatment residue is in

compliance with the applicable treatment standards set forth in Subpart D of

this Part. Such testing must be performed according to the frequency specified

in the facility's waste analysis plan as required by 35 Ill. Adm. Code 724.113

or 35 Ill. Adm. Code 725.113.

3)

Where the owner or operator is disposing of any waste that is subject to

the prohibitions under Section 728.133(f) but not subject to the prohibitions

set forth in Section 728.132, the owner or operator must ensure that such waste

is the subject of a certification according to the requirements of Section

728.108 prior to disposal in a landfill or surface impoundment unit, and that

such disposal is in accordance with the requirements of Section 728.105(h)(2).

The same requirement applies to any waste that is subject to the prohibitions

under Section 728.133(f) and also is subject to the statutory prohibitions in

the codified prohibitions in Section 728.139 or Section 728.132.

4)

Where the owner or operator is disposing of any waste that is a recyclable

material used in a manner constituting disposal subject to the provisions of 35

Ill. Adm. Code 726.120(b), the owner or operator is not subject to subsections

(c)(1) through (c)(3) of this Section with respect to such waste.

d)?

A generator or treater that first claims that hazardous debris is excluded

from the definition of hazardous waste under 35 Ill. Adm. Code 721.103(c)

721.103(f) (i.e., debris treated by an extraction or destruction technology

provided by Table F of this Part, and debris that has been delisted) is subject

to the following notification and certification requirements:

1)?

A one-time notification must be submitted to the Agency including the

following information:

A)

The name and address of the RCRA Subtitle D (municipal solid waste

landfill) facility receiving the treated debris;

B)

A description of the hazardous debris as initially generated, including

the applicable USEPA hazardous waste numbers; and

---

C)

?

For debris excluded under 35 Ill. Adm. Code 721.103(e)(1), the technology

from Table F of this Part used to treat the debris.

2) The notification must be updated if the debris is shipped to a different

facility and, for debris excluded under 35 Ill. Adm. Code 721.102(c)(1)

721.102(f)(1), if a different type of debris is treated or if a different

technology is used to treat the debris.

3)

For debris excluded under 35 Ill. Adm. Code 721.102(c)(1) 721.102(f)(1),

the owner or operator of the treatment facility must document and certify

compliance with the treatment standards of Table F of this Part, as follows:

A)

Records must be kept of all inspections, evaluations, and analyses of

treated debris that are made to determine compliance with the treatment

standards;

B)

Records must be kept of any data or information the treater obtains during

treatment of the debris that identifies key operating parameters of the

treatment unit; and

C)

For each shipment of treated debris, a certification of compliance with

the treatment standards must be signed by an authorized representative and

placed in the facility's files. The certification must state as follows:

I certify under penalty of law that the debris has been treated in accordance

with the requirements of 35 Ill. Adm. Code 728.145. I am aware that there are

significant penalties for making a false certification, including the

possibility of fine and imprisonment.

e)?

A generator or treater that first receives a determination from USEPA or

the Agency that a given contaminated soil subject to LDRs, as provided in

Section 728.149(a), no longer contains a listed hazardous waste and a generator

or treater that first determines that a contaminated soil subject to LDRs, as

provided in Section 728.149(a), no longer exhibits a characteristic of hazardous

waste must do the following:

1)

Prepare a one-time only documentation of these determinations including

all supporting information; and

2)

Maintain that information in the facility files and other records for a

minimum of three years.

(Source: Amended at 32 Ill. Reg.

, effective

Section 728.109?

Special Rules for Characteristic Wastes

a)?

The initial generator of a solid waste must determine each USEPA hazardous

waste number (waste code) applicable to the waste in order to determine the

applicable treatment standards under Subpart D of this Part. This determination

may be made concurrently with the hazardous waste determination required in

Section 722.111. For purposes of this Part, the waste must carry the waste code

for any applicable listing under Subpart D of 35 Ill. Adm. Code 721. In

addition, the waste must carry one or more of the waste codes under Subpart C of

35 Ill. Adm. Code 721 where the waste exhibits a characteristic, except in the

case when the treatment standard for the listed waste operates in lieu of the

treatment standard for the characteristic waste, as specified in subsection (b)

---

of this Section. If the generator determines that its waste displays a

characteristic of hazardous waste (and the waste is not D001 nonwastewaters

treated by CMBST, RORGS, or POLYM of Table C to this Part), the generator must

determine the underlying hazardous constituents (as defined at Section

728.102(i)) in the characteristic waste.

b)

Where a prohibited waste is both listed under Subpart D of 35 Ill. Adm.

Code 721 and exhibits a characteristic of hazardous waste under Subpart C of 35

Ill. Adm. Code 721, the treatment standard for the waste code listed in Subpart

D of 35?

Adm. Code 721 will operate in lieu of the standard for the waste

code under Subpart C of 35 Ill. Adm. Code 721, provided that the treatment

standard for the listed waste includes a treatment standard for the constituent

that causes the waste to exhibit the characteristic. Otherwise, the waste must

meet the treatment standards for all applicable listed and characteristic waste

codes.

c)

In addition to any applicable standards determined from the initial point

of generation, no prohibited waste that exhibits a characteristic under Subpart

C of 35 Ill. Adm. Code 721 must be land disposed, unless the waste complies with

the treatment standards under Subpart D of this Part.

d)

A waste that exhibits a characteristic of hazardous waste under Subpart C

of 35 Ill. Adm. Code 721 is also subject to Section 728.107 requirements, except

that once the waste is no longer hazardous, a one-time notification and

certification must be placed in the generator's or treater's on-site files and

sent to the Agency, cx

?

.*

this cction. The notification and certification that is placed in the

generator's or treater's files must be updated if the process or operation

generating the waste changes or if the RCRA Subtitle D (municipal solid waste

landfill) facility receiving the waste changes. However, thc generator or

tr atcr nccd only notify thc Agency on an annual basis if such–

change

occur.

sent to thc Agcnc

C.

thc y ar, but no later than December 31.

1)?

The notification must include the following information:

A)

The name and address of the RCRA Subtitle D (municipal solid waste

landfill) facility receiving the waste shipment; and

B)

A description of the waste as initially generated, including the

applicable USEPA hazardous waste numbers, the treatability groups, and the

underlying hazardous constituents (as defined in Section 728.102(i)), unless the

waste will be treated and monitored for all underlying hazardous constituents.

If all underlying hazardous constituents will be treated and monitored, there is

no requirement to list any of the underlying hazardous constituents on the

notice.

2)?

The certification must be signed by an authorized representative and must

state the language found in Section 728.107(b)(4). If treatment removes the

characteristic but does not meet standards applicable to underlying hazardous

constituents, then the certification found in Section 728.107(b)(4)(D) applies.

3)

nonhazardous waste injection well, and for which compliance with thc tr atmcnt

standards set forth in Section 728.118 and Table U to this Bart for underlying

hazardous constituents is achieved through pollution prevention that meets the

---

in CWA equivalent treatment,

- - -

A)?

A description of the pollution prevention mechanism and when it was

implemented, if alr dy complete;

D)

prevention;

C)

Thc mass of ach underlying hazardous constituent that must be removed,

adjusted to reflect variations in mars due to normal operating conditions, and

D)

Thc mass rcduction of ach underlying haz

achieved.

For a dccharactcrizcd waste managed on site in a wastewater tr atmcnt

be monitored annually. Monitoring results must be kept in on site files for

five y arc.

f)

system subject to the federal Cl n Water Act (CWA) for which all underlying

kept in on site files.

Section

(Source:

728.Tab1cTABLE

Amended at 32

CIll. ?

Reg.Technology ?

,

Codes

effective

and Description

?

of Technology-

Based Standards

Technology

Code Description of Technology-Based Standard

ADGAS Venting of compressed gases into an absorbing or reacting media (i.e.,

solid or liquid) -- venting can be accomplished through physical release

utilizing valves or piping; physical penetration of the container; or

penetration through detonation.

AMLGM Amalgamation of liquid, elemental mercury contaminated with radioactive

materials utilizing inorganic reagents such as copper, zinc, nickel, gold, and

sulfur that result in a nonliquid, semi-solid amalgam and thereby reducing

potential emissions of elemental mercury vapors to the air.

BIODG Biodegradation of organics or non-metallic inorganics (i.e., degradable

inorganics that contain the elements of phosphorus, nitrogen, and sulfur) in

units operated under either aerobic or anaerobic conditions such that a

surrogate compound or indicator parameter has been substantially reduced in

concentration in the residuals (e.g., total organic carbon (TOC) can often be

---

used as an indicator parameter for the biodegradation of many organic

constituents that cannot be directly analyzed in wastewater residues).

CARBN Carbon adsorption (granulated or powdered) of non-metallic inorganics,

organo-metallics, or organic constituents, operated so that a surrogate compound

or indicator parameter has not undergone breakthrough (e.g., total organic

carbon (TOC) can often be used as an indicator parameter for the adsorption of

many organic constituents that cannot be directly analyzed in wastewater

residues). Breakthrough occurs when the carbon has become saturated with the

constituent (or indicator parameter) and substantial change in adsorption rate

associated with that constituent occurs.

CHOXD Chemical or electrolytic oxidation utilizing the following oxidation

reagents (or waste reagents) or combinations or reagents:

1)

hypochlorite (e.g., bleach);

2) chlorine;

3) chlorine dioxide;

4)

ozone or UV (ultraviolet light) assisted ozone;

5)

peroxides;

6)

persulfates;

7)

perchlorates;

8)

permanganates; or

9)

other oxidizing reagents of equivalent efficiency, performed in units

operated so that a surrogate compound or indicator parameter has been

substantially reduced in concentration in the residuals (e.g., total organic

carbon (TOC) can often be used as an indicator parameter for the oxidation of

many organic constituents that cannot be directly analyzed in wastewater

residues). Chemical oxidation specifically includes what is commonly referred

to as alkaline chlorination.

CHRED Chemical reduction utilizing the following reducing reagents (or waste

reagents) or combinations of reagents:

1) sulfur dioxide;

2)

sodium, potassium, or alkali salts of sulfites, bisulfites,

metabisulfites, and polyethylene glycols (e.g., NaPEG and KPEG);

3) sodium hydrosulfide;

4)

ferrous salts; or

5)

other reducing reagents of equivalent efficiency, performed in units

operated such that a surrogate compound or indicator parameter has been

substantially reduced in concentration in the residuals (e.g., total organic

halogens (TOX) can often be used as an indicator parameter for the reduction of

many halogenated organic constituents that cannot be directly analyzed in

---

wastewater residues). Chemical reduction is commonly used for the reduction of

hexavalent chromium to the trivalent state.

CMBST High temperature organic destruction technologies, such as combustion in

incinerators, boilers, or industrial furnaces operated in accordance with the

applicable requirements of Subpart 0 of 35 Ill. Adm. Code 724, Subpart 0 of 35

Ill. Adm. Code 725, or Subpart H of 35 Ill. Adm. Code 726, and in other units

operated in accordance with applicable technical operating requirements; and

certain non-combustive technologies, such as the Catalytic Extraction Process.

DEACT Deactivation to remove the hazardous characteristics of a waste due to its

ignitability, corrosivity, or reactivity.

FSUBS Fuel substitution in units operated in accordance with applicable

technical operating requirements.

HLVIT Vitrification of high-level mixed radioactive wastes in units in

compliance with all applicable radioactive protection requirements under control

of the federal Nuclear Regulatory Commission.

IMERC Incineration of wastes containing organics and mercury in units operated

in accordance with the technical operating requirements of Subpart 0 of 35 Ill.

Adm. Code 724 or Subpart 0 of 35 Ill. Adm. Code 725. All wastewater and

nonwastewater residues derived from this process must then comply with the

corresponding treatment standards per waste code with consideration of any

applicable subcategories (e.g., high or low mercury subcategories).

INCIN Incineration in units operated in accordance with the technical operating

requirements of Subpart 0 of 35 Ill. Adm. Code 724 or Subpart 0 of 35 Ill. Adm.

Code 725.

LLEXT Liquid-liquid extraction (often referred to as solvent extraction) of

organics from liquid wastes into an immiscible solvent for which the hazardous

constituents have a greater solvent affinity, resulting in an extract high in

organics that must undergo either incineration, reuse as a fuel, or other

recovery or reuse and a raffinate (extracted liquid waste) proportionately low

in organics that must undergo further treatment as specified in the standard.

MACRO Macroencapsulation with surface coating materials such as polymeric

organics (e.g., resins and plastics) or with a jacket of inert inorganic

materials to substantially reduce surface exposure to potential leaching media.

Macroencapsulation specifically does not include any material that would be

classified as a tank or container according to 35 Ill. Adm. Code 720.110.

NEUTR Neutralization with the following reagents (or waste reagents) or

combinations of reagents:

1) acids;

2)

bases; or

3)

water (including wastewaters) resulting in a pH greater than two but less

than 12.5 as measured in the aqueous residuals.

NLDBR No land disposal based on recycling.

---

POLYM Formation of complex high-molecular weight solids through polymerization

of monomers in high-TOC D001 nonwastewaters that are chemical components in the

manufacture of plastics.

PRECP Chemical precipitation of metals and other inorganics as insoluble

precipitates of oxides, hydroxides, carbonates, sulfides, sulfates, chlorides,

fluorides, or phosphates. The following reagents (or waste reagents) are

typically used alone or in combination:

1)

lime (i.e., containing oxides or hydroxides of calcium or magnesium);

2)

caustic (i.e., sodium or potassium hydroxides);

3)

soda ash (i.e., sodium carbonate);

4)

sodium sulfide;

5)

ferric sulfate or ferric chloride;

6)

alum; or

7)

sodium sulfate. Additional flocculating, coagulation, or similar reagents

or processes that enhance sludge dewatering characteristics are not precluded

from use.

RBERY Thermal recovery of beryllium.

RCGAS Recovery or reuse of compressed gases including techniques such as

reprocessing of the gases for reuse or resale; filtering or adsorption of

impurities; remixing for direct reuse or resale; and use of the gas as a fuel

source.

RCORR Recovery of acids or bases utilizing one or more of the following recovery

technologies:

1)

distillation (i.e., thermal concentration);

2) ion exchange;

3)

resin or solid adsorption;

4)

reverse osmosis; or

5)

incineration for the recovery of acid

Note: this does not preclude the use of other physical phase separation or

concentration techniques such as decantation, filtration (including

ultrafiltration), and centrifugation, when used in conjunction with the above

listed recovery technologies.

RLEAD Thermal recovery of lead in secondary lead smelters.

RMERC Retorting or roasting in a thermal processing unit capable of volatilizing

mercury and subsequently condensing the volatilized mercury for recovery. The

retorting or roasting unit (or facility) must be subject to one or more of the

following:

---

a)

A federal national emissions standard for hazardous air pollutants

(NESHAP) for mercury (subpart E of 40 CFR 61);

b)

A best available control technology (BACT) or a lowest achievable emission

rate (LAER) standard for mercury imposed pursuant to a prevention of significant

deterioration (PSD) permit (including 35 Ill. Adm. Code 201 through 203); or

c)

A state permit that establishes emission limitations (within meaning of

Section 302 of the Clean Air Act) for mercury, including a permit issued

pursuant to 35 Ill. Adm. Code 201. All wastewater and nonwastewater residues

derived from this process must then comply with the corresponding treatment

standards per waste code with consideration of any applicable subcategories

(e.g., high or low mercury subcategories).

RMETL Recovery of metals or inorganics utilizing one or more of the following

direct physical or removal technologies:

1)

ion exchange;

2)

resin or solid (i.e., zeolites) adsorption;

3) reverse osmosis;

4)

chelation or solvent extraction;

5)

freeze crystallization;

6)

ultrafiltration; or

7)

simple precipitation (i.e., crystallization)

Note: this does not preclude the use of other physical phase separation or

concentration techniques such as decantation, filtration (including

ultrafiltration), and centrifugation, when used in conjunction with the above

listed recovery technologies.

RORGS Recovery of organics utilizing one or more of the following technologies:

1)

Distillation;

2)

thin film evaporation;

3)

steam stripping;

4)

carbon adsorption;

5)

critical fluid extraction;

6)

liquid-liquid extraction;

7)

precipitation or crystallization (including freeze crystallization); or

8)

chemical phase separation techniques (i.e., addition of acids, bases,

demulsifiers, or similar chemicals).

Note: This does not preclude the use of other physical phase separation

techniques such as decantation, filtration (including ultrafiltration), and

---

.

4

centrifugation, when used in conjunction with the above listed recovery

technologies.

RTHRM Thermal recovery of metals or inorganics from nonwastewaters in units

defined as cement kilns, blast furnaces, smelting, melting and refining

furnaces, combustion devices used to recover sulfur values from spent sulfuric

acid and "other devices" determined by the Agency pursuant to 35 Ill. Adm. Code

720.110, the definition of "industrial furnace."

RZINC Resmelting in high temperature metal recovery units for the purpose of

recovery of zinc.

STABL Stabilization with the following reagents (or waste reagents) or

combinations of reagents:

1)

Portland cement; or

2)

lime or pozzolans (e.g., fly ash and cement kiln dust) -- this does not

preclude the addition of reagents (e.g., iron salts, silicates, and clays)

designed to enhance the set or cure time or compressive strength, or to overall

reduce the leachability of the metal or inorganic.

SSTRP Steam stripping of organics from liquid wastes utilizing direct

application of steam to the wastes operated such that liquid and vapor flow

rates, as well as, temperature and pressure ranges, have been optimized,

monitored, and maintained. These operating parameters are dependent upon the

design parameters of the unit, such as, the number of separation stages and the

internal column design. Thus, resulting in a condensed extract high in organics

that must undergo either incineration, reuse as a fuel, or other recovery or

reuse and an extracted wastewater that must undergo further treatment as

specified in the standard.

WETOX Wet air oxidation performed in units operated such that a surrogate

compound or indicator parameter has been substantially reduced in concentration

in the residuals (e.g., total organic carbon (TOC) can often be used as an

indicator parameter for the oxidation of many organic constituents that cannot

be directly analyzed in wastewater residues).

WTRRX Controlled reaction with water for highly reactive inorganic or organic

chemicals with precautionary controls for protection of workers from potential

violent reactions as well as precautionary controls for potential emissions of

toxic or ignitable levels of gases released during the reaction.

Note 1:

?

When a combination of these technologies (i.e., a treatment train)

is specified as a single treatment standard, the order of application is

specified in Table T to this Part by indicating the five letter technology code

that must be applied first, then the designation "fb." (an abbreviation for

"followed by"), then the five letter technology code for the technology that

must be applied next, and so on.

Note 2:

?

When more than one technology (or treatment train) are specified as

alternative treatment standards, the five letter technology codes (or the

treatment trains) are separated by a semicolon (;) with the last technology

preceded by the word "OR." This indicates that any one of these BDAT

technologies or treatment trains can be used for compliance with the standard.

BOARD NOTE: Derived from Table I in 40 CFR 268.42 (2005) (2007).

---

(Source: Amended at 32 Ill. Reg.

, effective

Section 728.TabloTABLE, F?

Alternative Treatment Standards For Hazardous

Debris

a)

Hazardous debris must be treated by either the standards indicated in this

Table F or by the waste-specific treatment standards for the waste contaminating

the debris. The treatment standards must be met for each type of debris

contained in a mixture of debris types, unless the debris is converted into

treatment residue as a result of the treatment process. Debris treatment

residuals are subject to the waste-specific treatment standards for the waste

contaminating the debris.

b)

Definitions. For the purposes of this Table F, the following terms are

defined as follows:

"Clean debris surface" means the surface, when viewed without

magnification, must be free of all visible contaminated soil and hazardous waste

except that residual staining from soil and waste consisting of light shadows,

slight streaks, or minor discolorations, and soil and waste in cracks, crevices,

and pits may be present provided that such staining and waste and soil in

cracks, crevices, and pits must be limited to no more than five percent of each

square inch of surface area.

"Contaminant restriction" means that the technology is not BDAT for that

contaminant. If debris containing a restricted contaminant is treated by the

technology, the contaminant must be subsequently treated by a technology for

which it is not restricted in order to be land disposed (and excluded from

Subtitle C regulation).

"Dioxin-listed wastes" means wastes having any of USEPA hazardous waste

numbers F020, F021, F022, F023, F026, or F027.

c)

Notes. In this Table F, the following text is to be read in conjunction

with the tabulated text where the appropriate notations appear:

1 Acids, solvents, and chemical reagents may react with some debris and

contaminants to form hazardous compounds. For example, acid washing of cyanide-

contaminated debris could result in the formation of hydrogen cyanide. Some

acids may also react violently with some debris and contaminants, depending on

the concentration of the acid and the type of debris and contaminants. Debris

treaters should refer to the safety precautions specified in Material Safety

Data Sheets for various acids to avoid applying an incompatible acid to a

particular debris/contaminant combination. For example, concentrated sulfuric

acid may react violently with certain organic compounds, such as acrylonitrile.

2 If reducing the particle size of debris to meet the treatment standards

results in material that no longer meets the 60 mm minimum particle size limit

for debris, such material is subject to the waste-specific treatment standards

for the waste contaminating the material, unless the debris has been cleaned and

separated from contaminated soil and waste prior to size reduction. At a

minimum, simple physical or mechanical means must be used to provide such

cleaning and separation of nondebris materials to ensure that the debris surface

is free of caked soil, waste, or other nondebris material.

---

3 Thermal desorption is distinguished from thermal destruction in that the

primary purpose of thermal desorption is to volatilize contaminants and to

remove them from the treatment chamber for subsequent destruction or other

treatment.

4 The demonstration of "equivalent technology" undcrpursuant to Section

728.142(b) must document that the technology treats contaminants subject to

treatment to a level equivalent to that required by the performance and design

and operating standards for other technologies in this table such that residual

levels of hazardous contaminants will not pose a hazard to human health and the

environment absent management controls.

5 Any soil, waste, and other nondebris material that remains on the debris

surface (or remains mixed with the debris) after treatment is considered a

treatment residual that must be separated from the debris using, at a minimum,

simple physical or mechanical means. Examples of simple physical or mechanical

means are vibratory or trommel screening or water washing. The debris surface

need not be cleaned to a "clean debris surface" as defined in subsection (b) of

this Section when separating treated debris from residue; rather, the surface

must be free of caked soil, waste, or other nondebris material. Treatment

residuals are subject to the waste-specific treatment standards for the waste

contaminating the debris.

Technology descriptionPerformance or design and operating standard

Contaminant restrictionsA. Extraction Technologies:1. Physical Extractiona.

Abrasive Blasting: Removal of contaminated debris surface layers using water or

air pressure to propel a solid media (e.g., steel shot, aluminum oxide grit,

plastic beads).Glass, Metal, Plastic, Rubber: Treatment to a clean debris

surface.

Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Removal of at least 0.6 cm

of the surface layer; treatment to a clean debris surface.All Debris: None.b.

Scarification, Grinding, and Planing: Process utilizing striking piston heads,

saws, or rotating grinding wheels such that contaminated debris surface layers

are removed.Same as aboveSame as abovec. Spalling: Drilling or chipping holes

at appropriate locations and depth in the contaminated debris surface and

applying a tool that exerts a force on the sides of those holes such that the

surface layer is removed. The surface layer removed remains hazardous debris

subject to the debris treatment standards.Same as aboveSame as aboved.

Vibratory Finishing: Process utilizing scrubbing media, flushing fluid, and

oscillating energy such that hazardous contaminants or contaminated debris

surface layers are removed.lSame as aboveSame as abovee. High Pressure Steam

and Water Sprays: Application of water or steam sprays of sufficient

temperature, pressure, residence time, agitation, surfactants, and detergents to

remove hazardous contaminants from debris surfaces or to remove contaminated

debris surface layersSame as aboveSame as above.2. Chemical Extractiona. Water

Washing and Spraying: Application of water sprays or water baths of sufficient

temperature, pressure, residence time, agitation, surfactants, acids, bases, and

detergents to remove hazardous contaminants from debris surfaces and surface

pores or to remove contaminated debris surface layers.All Debris: Treatment to

a clean debris surface; Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood:

Debris must be no more than 1.2 cm (1/2 inch) in one dimension (i.e., thickness

limit,2 except that this thickness limit may be waived under an "Equivalent

Technology" approval undcrpursuant to Section 728.142(b);4 debris surfaces must

be in contact with water solution for at least 15 minutesBrick, Cloth, Concrete,

Paper, Pavement, Rock, Wood: Contaminant must be soluble to at least five

percent by weight in water solution or five percent by weight in emulsion; if

debris is contaminated with a dioxin-listed waste,3 an "Equivalent Technology"

---

approval undcrpursuant to Section 728.142(b) must be obtained.4b. Liquid Phase

Solvent Extraction: Removal of hazardous contaminants from debris surfaces and

surface pores by applying a nonaqueous liquid or liquid solution that causes the

hazardous contaminants to enter the liquid phase and be flushed away from the

debris along with the liquid or liquid solution while using appropriate

agitation, temperature, and residence time.lSame as aboveBrick, Cloth, Concrete,

Paper, Pavement, Rock, Wood: Same as above, except that contaminant must be

soluble to at least five percent by weight in the solvent.c. Vapor Phase

Solvent Extraction: Application of an organic vapor using sufficient agitation,

residence time, and temperature to cause hazardous contaminants on contaminated

debris surfaces and surface pores to enter the vapor phase and be flushed away

with the organic vapor.lSame as above, except that brick, cloth, concrete,

paper, pavement, rock and wood surfaces must be in contact with the organic

vapor for at least 60 minutes.Same as above.3. Thermal Extractiona. High

Temperature Metals Recovery: Application of sufficient heat, residence time,

mixing, fluxing agents, or carbon in a smelting, melting, or refining furnace to

separate metals from debris.For refining furnaces, treated debris must be

separated from treatment residuals using simple physical or mechanical means,5

and, prior to further treatment, such residuals must meet the waste-specific

treatment standards for organic compounds in the waste contaminating the

debris.Debris contaminated with a dioxin-listed waste:2 Obtain an "Equivalent

Technology" approval undcrpursuant to Section 728.142(b).4b. Thermal

Desorption: Heating in an enclosed chamber under either oxidizing or

nonoxidizing atmospheres at sufficient temperature and residence time to

vaporize hazardous contaminants from contaminated surfaces and surface pores and

to remove the contaminants from the heating chamber in a gaseous exhaust

gas.3All Debris: Obtain an "Equivalent Technology" approval

? *pursuant to

Section 728.142(b);4 treated debris must be separated from treatment residuals

using simple physical or mechanical means,5 and, prior to further treatment,

such residue must meet the waste-specific treatment standards for organic

compounds in the waste contaminating the debris.

Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more

than 10 cm (4 inches) in one dimension (i.e., thickness limit),2 except that

this thickness limit may be waived under the "Equivalent Technology" approvalAll

Debris: Metals other than mercury.B. Destruction Technologies:1. Biological

Destruction (Biodegradation): Removal of hazardous contaminants from debris

surfaces and surface pores in an aqueous solution and

CC^C

biodegradation of organic or nonmetallic inorganic compounds (i.e., inorganics

that contain phosphorus, nitrogen, or sulfur) in units operated under either

aerobic or anaerobic conditions.All Debris: Obtain an "Equivalent Technology"

approval undcrpursuant to Section 728.142(b);4 treated debris must be separated

from treatment residuals using simple physical or mechanical means,5 and, prior

to further treatment, such residue must meet the waste-specific treatment

standards for organic compounds in the waste contaminating the debris.

Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more

than 1.2 cm (1/2 inch) in one dimension (i.e., thickness limit),2 except that

this thickness limit may be waived under the "Equivalent Technology" approvalAll

Debris: Metal contaminants.2. Chemical Destructiona. Chemical Oxidation:

Chemical or electrolytic oxidation utilizing the following oxidation reagents

(or waste reagents) or combination of reagents: (1) hypochlorite (e.g.,

bleach); (2) chlorine; (3) chlorine dioxide; (4) ozone or UV (ultraviolet light)

assisted ozone; (5) peroxides; (6) persulfates; (7) perchlorates; (8)

permanganates; or (9) other oxidizing reagents of equivalent destruction

efficiency.) Chemical oxidation specifically includes what is referred to as

alkaline chlorination.All Debris: Obtain an "Equivalent Technology" approval

underpursuant to 35 Ill. Adm. Code.142(b);4 treated debris must be separated

from treatment residuals using simple physical or mechanical means,5 and, prior

---

to further treatment, such residue must meet the waste-specific treatment

standards for organic compounds in the waste contaminating the debris.

Brick, Cloth, Concrete, Paper, Pavement, Rock, Wood: Debris must be no more

than 1.2 cm (1/2 inch) in one dimension (i.e., thickness limit),2 except that

this thickness limit may be waived under the "Equivalent Technology" approvalAll

Debris: Metal contaminants.b. Chemical Reduction: Chemical reaction utilizing

the following reducing reagents (or waste reagents) or combination of reagents:

(1) sulfur dioxide; (2) sodium, potassium, or alkali salts of sulfites,

bisulfites, and metabisulfites, and polyethylene glycols (e.g., NaPEG and KPEG);

(3) sodium hydrosulfide; (4) ferrous salts; or (5) other reducing reagents of

equivalent efficiency.lSame as aboveSame as above.3. Thermal Destruction:

Treatment in an incinerator operating in accordance with Subpart 0 of 35 Ill.

Adm. Code 724 or Subpart 0 of 35 Ill. Adm. Code 725; a boiler or industrial

furnace operating in accordance with Subpart H of 35 Ill. Adm. Code 726, or

other thermal treatment unit operated in accordance with Subpart X of 35 Ill.

Adm. Code 724, or Subpart P of 35 Ill. Adm. Code 725, but excluding for purposes

of these debris treatment standards Thermal Desorption units.Treated debris must

be separated from treatment residuals using simple physical or mechanical

means,5 and, prior to further treatment, such residue must meet the waste-

specific treatment standards for organic compounds in the waste contaminating

the debris.Brick, Concrete, Glass, Metal, Pavement, Rock, Metal: Metals other

than mercury, except that there are no metal restrictions for vitrification.

Debris contaminated with a dioxin-listed waste.3 Obtain an "Equivalent

Technology" approval „pursuant to Section 728.142(b),4 except that this

requirement does not apply to vitrification.C. Immobilization Technologies:1.

Macroencapsulation: Application of surface coating materials such as polymeric

organics (e.g., resins and plastics) or use of a jacket of inert inorganic

materials to substantially reduce surface exposure to potential leaching

media.Encapsulating material must completely encapsulate debris and be resistant

to degradation by the debris and its contaminants and materials into which it

may come into contact after placement (leachate, other waste, microbes).None.2.

Microencapsulation: Stabilization of the debris with the following reagents (or

waste reagents) such that the leachability of the hazardous contaminants is

reduced: (1) Portland cement; or (2) lime/ pozzolans (e.g., fly ash and cement

kiln dust). Reagents (e.g., iron salts, silicates, and clays) may be added to

enhance the set/cure time or compressive strength, or to reduce the leachability

of the hazardous constituents.2Leachability of the hazardous contaminants must

be reduced.None.3. Sealing: Application of an appropriate material that

adheres tightly to the debris surface to avoid exposure of the surface to

potential leaching media. When necessary to effectively seal the surface,

sealing entails pretreatment of the debris surface to remove foreign matter and

to clean and roughen the surface. Sealing materials include epoxy, silicone,

and urethane compounds, but paint may not be used as a sealantSealing must avoid

exposure of the debris surface to potential leaching media and sealant must be

resistant to degradation by the debris and its contaminants and materials into

which it may come into contact after placement (leachate, other waste,

microbes).None.

BOARD NOTE: Derived from Table 1 to 40 CFR 268.45 (2005).

Section

(Source:

728.TabloTABLE,

Amended at 32

TIll.

?

Reg.

?

Treatment

--,

Standards

effective

for

?

Hazardous Wastes

Note: The treatment standards that heretofore appeared in tables in Sections

728.141, 728.142, and 728.143 have been consolidated into this table.

Waste Code

---

Waste Description and Treatment or Regulatory Subcategoryl

Regulated Hazardous ConstituentWastewatersNonwastewatersCommon NameCAS2

NumberConcentration3 in mg/1; or Technology Code4Concentration5 in mg/kg-S-

unless noted as " mg/1 TCLP"; or Technology Code4

D0019

Ignitable Characteristic Wastes, except for the 35 Iii. Adm. Code 721.121(a)(1)

High TOC Subcategory.

NANADEACT and meet Section 728.148 standards8; or RORGS; or CMBSTDEACT and meet

Section 728.148 standards8; or RORGS; or CHEST

D0019

High TOC Ignitable Characteristic Liquids Subcategory based on 35 Ill. Adm. Code

721.121(a)(1) - Greater than or equal to 10 percent total organic carbon.

(Note: This subcategory consists of nonwastewaters only.)

NANANARORGS; CMBST; or POLYM

D0029

Corrosive Characteristic Wastes.

NANADEACT and meet Section 728.148 standards8DEACT and meet Section 728.148

standards8

D002, D004, D005, D006, D007, D008, D009, D010, D011

Radioactive high level wastes generated during the reprocessing of fuel rods.

(Note: This subcategory consists of nonwastewaters only.)

Corrosivity (pH)NANAHLVITArsenic7440-38-2NAHLVITBarium7440-39-

3NAHLVITCadmium7440-43-9NAHLVITChromium (Total)7440-47-3NAHLVITLead7439-92-

1NAHLVITMercury7439-97-6NAHLVITSelenium7782-49-2NAHLVITSilver7440-22-4NAHLVIT

D0039

Reactive Sulfides Subcategory based on 35 Ill. Adm. Code 721.123(a)(5).

NANADEACTDEACT

D0039

Explosive subcategory based on 35 Ill. Adm. Code 721.123(a)(6), (a)(7), and

(a)(8).

NANADEACT and meet Section 728.148 standards8DEACT and meet Section 728.148

standards8

D0039

Unexploded ordnance and other explosive devices that have been the subject of an

emergency response.

NANADEACTDEACT

D0039

Other Reactives Subcategory based on 35 Ill. Adm. Code 721.123(a)(1).

---

NANADEACT and meet Section 728.148 standards8DEACT and meet Section 728.148

standards8

D0039

Water Reactive Subcategory based on 35 Ill. Adm. Code 721.123(a)(2), (a)(3), and

(a)(4).

(Note: This subcategory consists of nonwastewaters only.)

NANANADEACT and meet Section 728.148 standards8

D0039

Reactive Cyanides Subcategory based on 35 Ill. Adm. Code 721.123(a)(5).

Cyanides (Total)757-12-5--590Cyanides (Amenable)757-12-50.8630

D0049

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for arsenic based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Arsenic7440-38-21.4 and meet Section 728.148 standards85.0 mg/1 TCLP and meet

Section 728.148 standards8

D0059

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for barium based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Barium7440-39-31.2 and meet Section 728.148 standards821 mg/1 TCLP and meet

Section 728.148 standards8

D0069

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for cadmium based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Cadmium7440-43-90.69 and meet Section 728.148 standards80.11 mg/1 TCLP and meet

Section 728.148 standards8

D0069

Cadmium-Containing Batteries Subcategory.

(Note: This subcategory consists of nonwastewaters only.)

Cadmium7440-43-9NARTHRM

D0069

Radioactively contaminated cadmium-containing batteries.

---

(Note: This subcategory consists of nonwastewaters only.)

Cadmium7440-43-9NAMacroencapsulation in accordance with Section 728.145

D0079

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for chromium based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 III.

Adm. Code 720.111(a).

Chromium (Total)7440-47-32.77 and meet Section 728.148 standards80.60 mg/1 TCLP

and meet Section 728.148 standards8

D0089

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for lead based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Lead7439-92-10.69 and meet Section 728.148 standards80.75 mg/1 TCLP and meet

Section 728.148 standards8

D0089

Lead Acid Batteries Subcategory

(Note: This standard only applies to lead acid batteries that are identified as

RCRA hazardous wastes and that are not excluded elsewhere from regulation under

the land disposal restrictions of this Part or exempted under other regulations

(see 35 Ill. Adm. Code 726.180). This subcategory consists of nonwastewaters

only.)

Lead7439-92-1NARLEAD

D0089

Radioactive Lead Solids Subcategory

(Note: These lead solids include, but are not limited to, all forms of lead

shielding and other elemental forms of lead. These lead solids do not include

treatment residuals such as hydroxide sludges, other wastewater treatment

residuals, or incinerator ashes that can undergo conventional pozzolanic

stabilization, nor do they include organo-lead materials that can be incinerated

and stabilized as ash. This subcategory consists of nonwastewaters only.)

Lead7439-92-1NAMACRO

D0099

Nonwastewaters that exhibit, or are expected to exhibit, the characteristic of

toxicity for mercury based on Method 1311 (Toxicity Characteristic Leaching

Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical

Methods," USEPA publication number EPA-530/SW-846, incorporated by reference in

35 Ill. Adm. Code 720.111(a); and contain greater than or equal to 260 mg/kg

total mercury that also contain organics and are not incinerator residues.

(High Mercury-Organic Subcategory)

Mercury7439-97-6NAIMERC; or RMERC

---

D0099

Nonwastewaters that exhibit, or are expected to exhibit, the characteristic of

toxicity for mercury based on Method 1311 (Toxicity Characteristic Leaching

Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical

Methods," USEPA publication number EPA-530/SW-846, incorporated by reference in

35 Ill. Adm. Code 720.111(a); and contain greater than or equal to 260 mg/kg

total mercury that are inorganic, including incinerator residues and residues

from RMERC. (High Mercury-Inorganic Subcategory)

Mercury7439-97-6NARMERC

D0099

Nonwastewaters that exhibit, or are expected to exhibit, the characteristic of

toxicity for mercury based on Method 1311 (Toxicity Characteristic Leaching

Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical

Methods," USEPA publication number EPA-530/SW-846, incorporated by reference in

35 Ill. Adm. Code 720.111(a); and contain less than 260 mg/kg total mercury.

(Low Mercury Subcategory)

Mercury7439-97-6NA0.20 mg/1 TCLP and meet Section 728.148 standards8

D0099

All other nonwastewaters that exhibit, or are expected to exhibit, the

characteristic of toxicity for mercury based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a); and contain less than

260 mg/kg total mercury and that are not residues from RMERC. (Low Mercury

Subcategory)

Mercury7439-97-6NA0.025 mg/1 TCLP and meet Section 728.148 standards8

D0099

All D009 wastewaters.

Mercury7439-97-60.15 and meet Section 728.148 standards8NA

D0099

Elemental mercury contaminated with radioactive materials.

(Note: This subcategory consists of nonwastewaters only.)

Mercury7439-97-6NAAMLGM

D0099

Hydraulic oil contaminated with Mercury Radioactive Materials Subcategory.

(Note: This subcategory consists of nonwastewaters only.)

Mercury7439-97-6NAIMERC

D0099

Radioactively contaminated mercury-containing batteries.

(Note: This subcategory consists of nonwastewaters only.)

---

Mercury7439-97-6NAMacroencapsulation in accordance with Section 728.145

D0109

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for selenium based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Selenium7782-49-20.825.7 mg/1 TCLP and meet Section 728.148 standards8

D0119

Wastes that exhibit, or are expected to exhibit, the characteristic of toxicity

for silver based on Method 1311 (Toxicity Characteristic Leaching Procedure

(TCLP)) in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,"

USEPA publication number EPA-530/SW-846, incorporated by reference in 35 Ill.

Adm. Code 720.111(a).

Silver7440-22-40.430.14 mg/1 TCLP and meet Section 728.148 standards8

D0119

Radioactively contaminated silver-containing batteries.

(Note: This subcategory consists of nonwastewaters only.)

Silver7440-22-4NAMacroencapsulation in accordance with Section 728.145

D0129

Wastes that are TC for endrin based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Endrin72-20-8BIODG; or CMBST0.13 and meet Section 728.148 standards8Endrin

aldehyde7421-93-4BIODG; or CMBST0.13 and meet Section 728.148 standards8

D0139

Wastes that are TC for lindane based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

-BHC319-84-6CARBN; or CMBST0.066 and meet Section 728.148 standards8-BHC319-85-

7CARBN; or CMBST0.066 and meet Section 728.148 standards8-BHC319-86-8CARBN; or

CMBST0.066 and meet Section 728.148 standards8?-BHC (Lindane)58-89-9CARBN; or

CMBST0.066 and meet Section 728.148 standards8

D0149

Wastes that are TC for methoxychlor based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Methoxychlor72-43-5WETOX or CMBST0.18 and meet Section 728.148 standards8

D0159

---

Wastes that are TC for toxaphene based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Toxaphene8001-35-2BIODG or CMBST2.6 and meet Section 728.148 standards8

D0169

Wastes that are TC for 2,4-D (2,4-dichlorophenoxyacetic acid) based on Method

1311 (Toxicity Characteristic Leaching Procedure (TCLP)) in "Test Methods for

Evaluating Solid Waste, Physical/Chemical Methods," USEPA publication number

EPA-530/SW-846, incorporated by reference in 35 Ill. Adm. Code 720.111(a).

2,4-D (2,4-dichlorophenoxyacetic acid)94-75-7CHOXD; BIODG; or CMBST10 and meet

Section 728.148 standards8

D0179

Wastes that are TC for 2,4,5-TP (Silvex) based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

2,4,5-TP (Silvex)93-72-1CHOXD or CMBST7.9 and meet Section 728.148 standards8

D0189

Wastes that are TC for benzene based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Benzene71-43-20.14 and meet Section 728.148 standards810 and meet Section

728.148 standards8

D0199

Wastes that are TC for carbon tetrachloride based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Carbon tetrachloride56-23-50.057 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0209

Wastes that are TC for chlordane based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Chlordane ( and isomers)57-74-90.0033 and meet Section 728.148 standards80.26

and meet Section 728.148 standards8

D0219

Wastes that are TC for chlorobenzene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

---

Chlorobenzene108-90-70.057 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0229

Wastes that are TC for chloroform based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Chloroform67-66-30.046 and meet Section 728.148 standards86.0 and meet Section

728.148 standards8

D0239

Wastes that are TC for o-cresol based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

o-Creso195-48-70.11 and meet Section 728.148 standards85.6 and meet Section

728.148 standards8

D0249

Wastes that are TC for m-cresol based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

m-Cresol

(difficult to distinguish from p-cresol)108-39-40.77 and meet Section 728.148

standards85.6 and meet Section 728.148 standards8

D0259

Wastes that are TC for p-cresol based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

p-Cresol

(difficult to distinguish from m-cresol)106-44-50.77 and meet Section 728.148

standards85.6 and meet Section 728.148 standards8

D0269

Wastes that are TC for cresols (total) based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Cresol-mixed isomers (Cresylic acid)

(sum of o-, m-, and p-cresol concentrations)1319-77-30.88 and meet Section

728.148 standards811.2 and meet Section 728.148 standards8

D0279

Wastes that are TC for p-dichlorobenzene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

---

p-Dichlorobenzene (1,4-Dichlorobenzene)106-46-70.090 and meet Section 728.148

standards86.0 and meet Section 728.148 standards8

D0289

Wastes that are TC for 1,2-dichloroethane based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

1,2-Dichloroethane107-06-20.21 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0299

Wastes that are TC for 1,1-dichloroethylene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

1,1-Dichloroethylene75-35-40.025 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0309

Wastes that are TC for 2,4-dinitrotoluene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

2,4-Dinitrotoluene121-14-20.32 and meet Section 728.148 standards8140 and meet

Section 728.148 standards8

D0319

Wastes that are TC for heptachlor based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Heptachlor76-44-80.0012 and meet Section 728.148 standards80.066 and meet

Section 728.148 standards8Heptachlor epoxide1024-57-30.016 and meet Section

728.148 standards80.066 and meet Section 728.148 standards8

D0329

Wastes that are TC for hexachlorobenzene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Hexachlorobenzene118-74-10.055 and meet Section 728.148 standards810 and meet

Section 728.148 standards8

D0339

Wastes that are TC for hexachlorobutadiene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Hexachlorobutadiene87-68-30.055 and meet Section 728.148 standards85.6 and meet

Section 728.148 standards8

---

D0349

Wastes that are TC for hexachloroethane based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Hexachloroethane67-72-10.055 and meet Section 728.148 standards830 and meet

Section 728.148 standards8

D0359

Wastes that are TC for methyl ethyl ketone based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Methyl ethyl ketone78-93-30.28 and meet Section 728.148 standards836 and meet

Section 728.148 standards8

D0369

Wastes that are TC for nitrobenzene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Nitrobenzene98-95-30.068 and meet Section 728.148 standards814 and meet Section

728.148 standards8

D0379

Wastes that are TC for pentachlorophenol based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Pentachlorophenol87-86-50.089 and meet Section 728.148 standards87.4 and meet

Section 728.148 standards8

D0389

Wastes that are TC for pyridine based on Method 1311 (Toxicity Characteristic

Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid Waste,

Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Pyridine110-86-10.014 and meet Section 728.148 standards816 and meet Section

728.148 standards8

D0399

Wastes that are TC for tetrachloroethylene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Tetrachloroethylene127-18-40.056 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0409

---

Wastes that are TC for trichloroethylene based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Trichloroethylene79-01-60.054 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

D0419

Wastes that are TC for 2,4,5-trichlorophenol based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

2,4,5-Trichloropheno195-95-40.18 and meet Section 728.148 standards87.4 and meet

Section 728.148 standards8

D0429

Wastes that are TC for 2,4,6-trichlorophenol based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

2,4,6-Trichlorophenol88-06-20.035 and meet Section 728.148 standards87.4 and

meet Section 728.148 standards8

D0439

Wastes that are TC for vinyl chloride based on Method 1311 (Toxicity

Characteristic Leaching Procedure (TCLP)) in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a).

Vinyl chloride75-01-40.27 and meet Section 728.148 standards86.0 and meet

Section 728.148 standards8

F001, F002, F003, F004 & F005

F001, F002, F003, F004, or F005 solvent wastes that contain any combination of

one or more of the following spent solvents: acetone, benzene, n-butyl alcohol,

carbon disulfide, carbon tetrachloride, chlorinated fluorocarbons,

chlorobenzene, o-cresol, m-cresol, p-cresol, cyclohexanone, o-dichlorobenzene,

2-ethoxyethanol, ethyl acetate, ethyl benzene, ethyl ether, isobutyl alcohol,

methanol, methylene chloride, methyl ethyl ketone, methyl isobutyl ketone,

nitrobenzene, 2-nitropropane, pyridine, tetrachloroethylene, toluene, 1,1,1-

trichloroethane, 1,1,2-trichloroethane, 1,1,2-trichloro-1,2,2-trifluoroethane,

trichloroethylene, trichloromonofluoromethane, or xylenes (except as

specifically noted in other subcategories). See further details of these

listings in 35 Ill. Adm. Code 721.131.

Acetone67-64-10.28160Benzene71-43-20.1410n-Butyl alcohol71-36-35.62.6Carbon

disulfide75-15-03.8NACarbon tetrachloride56-23-50.0576.0Chlorobenzene108-90-

70.0576.0o-Creso195-48-70.115.6m-Cresol

(difficult to distinguish from p-cresol)108-39-40.775.6p-Cresol

(difficult to distinguish from m-cresol)106-44-50.775.6Cresol-mixed isomers

(Cresylic acid)

(sum of o-, m-, and p-cresol concentrations)1319-77-30.8811.2Cyclohexanone108-

94-10.36NAo-Dichlorobenzene95-50-10.0886.0Ethyl acetate141-78-60.3433Ethyl

benzene100-41-40.05710Ethyl ether60-29-70.12160Isobutyl alcohol78-83-

---

15.6170Methano167-56-15.6NAMethylene chloride75-9-20.08930Methyl ethyl ketone78-

93-30.2836Methyl isobutyl ketone108-10-10.1433Nitrobenzene98-95-

30.06814Pyridine110-86-10.01416Tetrachloroethylene127-18-40.0566.0Toluene108-88-

30.080101,1,1-Trichloroethane71-55-60.0546.01,1,2-Trichloroethane79-00-

50.0546.01,1,2-Trichloro-1,2,2-trifluoroethane76-13-10.05730Trichloroethylene79-

01-60.0546.0Trichloromonofluoromethane75-69-40.02030Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230

F001, F002, F003, F004 & F005

F003 and F005 solvent wastes that contain any combination of one or more of the

following three solvents as the only listed F001 through F005 solvents: carbon

disulfide, cyclohexanone, or methanol. (Formerly Section 728.141(c)).

Carbon disulfide75-15-03.84.8 mg/1 TCLPCyclohexanone108-94-10.360.75 mg/1

TCLPMethano167-56-15.60.75 mg/1 TCLP

F001, F002, F003, F004 & F005

F005 solvent waste containing 2-Nitropropane as the only listed F001 through

F005 solvent.

2-Nitropropane79-46-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

F001, F002, F003, F004 & F005

F005 solvent waste containing 2-Ethoxyethanol as the only listed F001 through

F005 solvent.

2-Ethoxyethano1110-80-5BIODG; or CMBSTCMBST

F006

Wastewater treatment sludges from electroplating operations except from the

following processes: (1) Sulfuric acid anodizing of aluminum; (2) tin plating

on carbon steel; (3) zinc plating (segregated basis) on carbon steel; (4)

aluminum or zinc-aluminum plating on carbon steel; (5) cleaning or stripping

associated with tin, zinc, and aluminum plating on carbon steel; and (6)

chemical etching and milling of aluminum.

Cadmium7440-43-90.690.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

F007

Spent cyanide plating bath solutions from electroplating operations.

Cadmium7440-43-9NA0.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

F008

Plating bath residues from the bottom of plating baths from electroplating

operations where cyanides are used in the process.

Cadmium7440-43-9NA0.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

---

F009

Spent stripping and cleaning bath solutions from electroplating operations where

cyanides are used in the process.

Cadmium7440-43-9NA0.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

F010

Quenching bath residues from oil baths from metal heat-treating operations where

cyanides are used in the process.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.86NA

FOil

Spent cyanide solutions from salt bath pot cleaning from metal heat-treating

operations.

Cadmium7440-43-9NA0.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Tota1)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

F012

Quenching wastewater treatment sludges from metal heat-treating operations where

cyanides are used in the process.

Cadmium7440-43-9NA0.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Lead7439-92-

10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSilver7440-22-4NA0.14 mg/1

TCLP

F019

Wastewater treatment sludges from the chemical conversion coating of aluminum,

except from zirconium phosphating in aluminum can washing when such phosphating

is an exclusive conversion coating process.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPCyanides (Total)757-12-

51.2590Cyanides (Amenable)757-12-50.8630

F020, F021, F022, F023, F026

Wastes (except wastewater and spent carbon from hydrogen chloride purification)

from the production or manufacturing use (as a reactant, chemical intermediate,

or component in a formulating process) of: (1) tri- or tetrachlorophenol, or of

intermediates used to produce their pesticide derivatives, excluding wastes from

the production of Hexachlorophene from highly purified 2,4,5-trichlorophenol

(i.e., F020); (2) pentachlorophenol, or of intermediates used to produce its

derivatives (i.e., F021); (3) tetra-, penta-, or hexachlorobenzenes under

alkaline conditions (i.e., F022) and wastes (except wastewater and spent carbon

from hydrogen chloride purification) from the production of materials on

equipment previously used for the production or manufacturing use (as a

reactant, chemical intermediate, or component in a formulating process) of: (1)

tri- or tetrachlorophenols, excluding wastes from equipment used only for the

production of Hexachlorophene from highly purified 2,4,5-trichlorophenol (F023)

---

or (2) tetra-, penta-, or hexachlorobenzenes under alkaline conditions (i.e.,

F026).

HxCDDs (All Hexachlorodibenzo-p-dioxins)NA0.0000630.001HxCDFs (All

Hexachlorodibenzofurans)55684-94-10.0000630.001PeCDDs (All Pentachlorodibenzo-p-

dioxins)36088-22-90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-

40.0000350.001Pentachloropheno187-86-50.0897.4TCDDs (All Tetrachlorodibenzo-p-

dioxins)41903-57-50.0000630.001TCDFs (All Tetrachlorodibenzofurans)55722-27-

50.0000630.0012,4,5-Trichloropheno195-95-40.187.42,4,6-Trichloropheno188-06-

20.0357.42,3,4,6-Tetrachloropheno158-90-20.0307.4

F024

Process wastes, including but not limited to, distillation residues, heavy ends,

tars, and reactor clean-out wastes, from the production of certain chlorinated

aliphatic hydrocarbons by free radical catalyzed processes. These chlorinated

aliphatic hydrocarbons are those having carbon chain lengths ranging from one to

and including five, with varying amounts and positions of chlorine substitution.

(This listing does not include wastewaters, wastewater treatment sludges, spent

catalysts, and wastes listed in 35 Ill. Adm. Code 721.131 or 721.132.)

All F024 wastesNACMBST11CMBST112-Chloro-1,3-butadiene126-99-80.0570.283-

Chloropropylene107-05-10.036301,1-Dichloroethane75-34-30.0596.01,2-

Dichloroethane107-06-20.216.01,2-Dichloropropane78-87-50.8518cis-1,3-

Dichloropropylene10061-01-50.03618trans-1,3-Dichloropropylene10061-02-

60.03618bis(2-Ethylhexyl) phthalate117-81-70.2828Hexachloroethane67-72-

10.05530Chromium (Total)7440-47-32.770.60 mg/1 TCLPNickel7440-02-03.9811 mg/1

TCLP

F025

Condensed light ends from the production of certain chlorinated aliphatic

hydrocarbons by free radical catalyzed processes. These chlorinated aliphatic

hydrocarbons are those having carbon chain lengths ranging from one up to and

including five, with varying amounts and positions of chlorine substitution.

F025 -- Light Ends Subcategory.

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-30.0466.01,2-

Dichloroethane107-06-20.216.01,1-Dichloroethylene75-35-40.0256.0Methylene

chloride75-9-20.089301,1,2-Trichloroethane79-00-50.0546.0Trichloroethylene79-01-

60.0546.0Vinyl chloride75-01-40.276.0

F025

Spent filters and filter aids, and spent desiccant wastes from the production of

certain chlorinated aliphatic hydrocarbons by free radical catalyzed processes.

These chlorinated aliphatic hydrocarbons are those having carbon chain lengths

ranging from one to and including five, with varying amounts and positions of

chlorine substitution. F025 -- Spent Filters/Aids and Desiccants Subcategory.

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-

30.0466.0Hexachlorobenzene118-74-10.05510Hexachlorobutadiene87-68-

30.0555.6Hexachloroethane67-72-10.05530Methylene chloride75-9-20.089301,1,2-

Trichloroethane79-00-50.0546.0Trichloroethylene79-01-60.0546.0Vinyl chloride75-

01-40.276.0

F027

Discarded unused formulations containing tri-, tetra-, or pentachlorophenol or

discarded unused formulations containing compounds derived from these

chlorophenols. (This listing does not include formulations containing

---

hexachlorophene synthesized from prepurified 2,4,5-trichiorophenol as the sole

component.)

HxCDDs (All Hexachlorodibenzo-p-dioxins)NA0.0000630.001HxCDFs (All

Hexachlorodibenzofurans)55684-94-10.0000630.001PeCDDs (All Pentachlorodibenzo-p-

dioxins)36088-22-90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-

40.0000350.001Pentachloropheno187-86-50.0897.4TCDDs (All Tetrachlorodibenzo-p-

dioxins)41903-57-50.0000630.001TCDFs (All Tetrachlorodibenzofurans)55722-27-

50.0000630.0012,4,5-Trichloropheno195-95-40.187.42,4,6-Trichloropheno188-06-

20.0357.42,3,4,6-Tetrachloropheno158-90-20.0307.4

F028

Residues resulting from the incineration or thermal treatment of soil

contaminated with USEPA hazardous waste numbers F020, F021, F023, F026, and

F027.

HxCDDs (All Hexachlorodibenzo-p-dioxins)NA0.0000630.001HxCDFs (All

Hexachlorodibenzofurans)55684-94-10.0000630.001PeCDDs (All Pentachlorodibenzo-p-

dioxins)36088-22-90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-

40.0000350.001Pentachloropheno187-86-50.0897.4TCDDs (All Tetrachlorodibenzo-p-

dioxins)41903-57-50.0000630.001TCDFs (All Tetrachlorodibenzofurans)55722-27-

50.0000630.0012,4,5-Trichloropheno195-95-40.187.42,4,6-Trichloropheno188-06-

20.0357.42,3,4,6-Tetrachloropheno158-90-20.0307.4

F032

Wastewaters (except those that have not come into contact with process

contaminants), process residuals, preservative drippage, and spent formulations

from wood preserving processes generated at plants that currently use or have

previously used chlorophenolic formulations (except potentially cross-

contaminated wastes that have had the F032 waste code deleted in accordance with

35 Ill. Adm. Code 721.135 or potentially cross-contaminated wastes that are

otherwise currently regulated as hazardous wastes (i.e., F034 or F035), where

the generator does not resume or initiate use of chlorophenolic formulations).

This listing does not include K001 bottom sediment sludge from the treatment of

wastewater from wood preserving processes that use creosote or penta-

chlorophenol.

Acenaphthene83-32-90.0593.4Anthracene120-12-70.0593.4Benz(a)anthracene56-55-

30.0593.4Benzo(b)fluoranthene (difficult to distinguish from benzo(k)

fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to distinguish from

benzo(b) fluoranthene)207-08-90.116.8Benzo(a)pyrene50-32-80.0613.4Chrysene218-

01-90.0593.4Dibenz(a,h)anthracene53-70-30.0558.22-4-Dimethyl pheno1105-67-

90.03614Fluorene86-73-70.0593.4Hexachlorodibenzo-p-dioxinsNA0.000063 or

CMBST110.001 or CMBST11HexachlorodibenzofuransNA0.000063 or CMBST110.001 or

CMBST1lIndeno (1,2,3-c,d) pyrene193-39-50.00553.4Naphthalene91-20-

30.0595.6Pentachlorodibenzo-p-dioxinsNA0.000063 or CMBST110.001 or

CMBST11PentachlorodibenzofuransNA0.000035 or CMBST110.001 or

CMBST11Pentachloropheno187-86-50.0897.4Phenanthrene85-01-80.0595.6Pheno1108-95-

20.0396.2Pyrene129-00-00.0678.2Tetrachlorodibenzo-p-dioxinsNA0.000063 or

CMBST110.001 or CMBST11TetrachlorodibenzofuransNA0.000063 or CMBST110.001 or

CMBST112,3,4,6-Tetrachloropheno158-90-20.0307.42,4,6-Trichloropheno188-06-

20.0357.4Arsenic7440-38-21.45.0 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLP

F034

Wastewaters (except those that have not come into contact with process

contaminants), process residuals, preservative drippage, and spent formulations

---

from wood preserving processes generated at plants that use creosote

formulations. This listing does not include K001 bottom sediment sludge from

the treatment of wastewater from wood preserving processes that use creosote or

pentachlorophenol.

Acenaphthene83-32-90.0593.4Anthracene120-12-70.0593.4Benz(a)anthracene56-55-

30.0593.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Benzo(a)pyrene50-32-

80.0613.4Chrysene218-01-90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Fluorene86-

73-70.0593.4Indeno (1,2,3-c,d) pyrene193-39-50.00553.4Naphthalene91-20-

30.0595.6Phenanthrene85-01-80.0595.6Pyrene129-00-00.0678.2Arsenic7440-38-21.45.0

mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1 TCLP

F035

Wastewaters (except those that have not come into contact with process

contaminants), process residuals, preservative drippage, and spent formulations

from wood preserving processes that are generated at plants that use inorganic

preservatives containing arsenic or chromium. This listing does not include

K001 bottom sediment sludge from the treatment of wastewater from wood

preserving processes that use creosote or pentachlorophenol.

Arsenic7440-38-21.45.0 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1 TCLP

F037

Petroleum refinery primary oil/water/solids separation sludge -- Any sludge

generated from the gravitational separation of oil/water/solids during the

storage or treatment of process wastewaters and oily cooling wastewaters from

petroleum refineries. Such sludges include, but are not limited to, those

generated in: oil/water/solids separators; tanks, and impoundments; ditches,

and other conveyances; sumps; and stormwater units receiving dry weather flow.

Sludge generated in stormwater units that do not receive dry weather flow,

sludges generated from non-contact once-through cooling waters segregated for

treatment from other process or oily cooling waters, sludges generated in

aggressive biological treatment units as defined in 35 Ill. Adm. Code

721.131(b) (2) (including sludges generated in one or more additional units after

wastewaters have been treated in aggressive biological treatment units) and K051

wastes are not included in this listing.

Acenaphthene83-32-90.059NAAnthracene120-12-70.0593.4Benzene71-43-

20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-80.0613.4bis(2-

Ethylhexyl) phthalate117-81-70.2828Chrysene218-01-90.0593.4Di-n-butyl

phthalate84-74-20.05728Ethylbenzene100-41-40.05710Fluorene86-73-

70.059NANaphthalene91-20-30.0595.6Phenanthrene85-01-80.0595.6Pheno1108-95-

20.0396.2Pyrene129-00-00.0678.2Toluene108-88-30.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Chromium (Total)7440-

47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Lead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

F038

Petroleum refinery secondary (emulsified) oil/water/solids separation sludge or

float generated from the physical or chemical separation of oil/water/solids in

process wastewaters and oily cooling wastewaters from petroleum refineries.

Such wastes include, but are not limited to, all sludges and floats generated

in: induced air floatation (IAF) units, tanks, and impoundments, and all

sludges generated in DAF units. Sludges generated in stormwater units that do

not receive dry weather flow, sludges generated from non-contact once-through

---

cooling waters segregated for treatment from other process or oily cooling

waters, sludges, and floats generated in aggressive biological treatment units

as defined in 35 Ill. Adm. Code 721.131(b)(2) (including sludges and floats

generated in one or more additional units after wastewaters have been treated in

aggressive biological units) and F037, K048, and K051 are not included in this

listing.

Benzene71-43-20.1410Benzo(a)pyrene50-32-80.0613.4bis(2-Ethylhexyl) phthalate117-

81-70.2828Chrysene218-01-90.0593.4Di-n-butyl phthalate84-74-

20.05728Ethylbenzene100-41-40.05710Fluorene86-73-70.059NANaphthalene91-20-

30.0595.6Phenanthrene85-01-80.0595.6Pheno1108-95-20.0396.2Pyrene129-00-

00.0678.2Toluene108-88-30.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Chromium (Total)7440-

47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Lead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

F039

Leachate (liquids that have percolated through land disposed wastes) resulting

from the disposal of more than one restricted waste classified as hazardous

under Subpart D of this Part. (Leachate resulting from the disposal of one or

more of the following USEPA hazardous wastes and no other hazardous wastes

retains its USEPA hazardous waste numbers: F020, F021, F022, F026, F027, or

F028.).

Acenaphthylene208-96-80.0593.4Acenaphthene83-32-90.0593.4Acetone67-64-

10.28160Acetonitrile75-05-85.6NAAcetophenone96-86-20.0109.72-

Acetylaminofluorene53-96-30.059140Acrolein107-02-80.29NAAcrylonitrile107-13-

10.2484Aldrin309-00-20.0210.0664-Aminobipheny192-67-10.13NAAniline62-53-

30.8114o-Anisidine (2-methoxyaniline)90-04-00.0100.66Anthracene120-12-

70.0593.4Aramite140-57-80.36NA-DHC319-84-60.000140.066-BHC319-85-70.000140.066-

BHC319-86-80.0230.066?-BHC58-89-90.00170.066Benzene71-43-

20.1410Benz(a)anthracene56-55-30.0593.4Benzo(b)fluoranthene (difficult to

distinguish from benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene

(difficult to distinguish from benzo(b)fluoranthene)207-08-

90.116.8Benzo(g,h,i)perylene191-24-20.00551.8Benzo(a)pyrene50-32-

80.0613.4Bromodichloromethane75-27-40.3515Methyl bromide (Bromomethane)74-83-

90.11154-Bromophenyl phenyl ether101-55-30.05515n-Butyl alcohol71-36-

35.62.6Butyl benzyl phthalate85-68-70.017282-sec-Butyl-4,6-dinitrophenol

(Dinoseb)88-85-70.0662.5Carbon disulfide75-15-03.8NACarbon tetrachloride56-23-

50.0576.0Chlordane ( and isomers)57-74-90.00330.26p-Chloroaniline106-47-

80.4616Chlorobenzene108-90-70.0576.0Chlorobenzilate510-15-60.10NA2-Chloro-1,3-

butadiene126-99-80.057NAChlorodibromomethane124-48-10.05715Chloroethane75-00-

30.276.0bis(2-Chloroethoxy)methane111-91-10.0367.2bis(2-Chloroethyl)ether111-44-

40.0336.0Chloroform67-66-30.0466.0bis(2-Chloroisopropyl)ether39638-32-

90.0557.2p-Chloro-m-creso159-50-70.01814Chloromethane (Methyl chloride)74-87-

30.19302-Chloronaphthalene91-58-70.0555.62-Chloropheno195-57-80.0445.73-

Chloropropylene107-05-10.03630Chrysene218-01-90.0593.4p-Cresidine120-71-

80.0100.66o-Creso195-48-70.115.6m-Cresol

(difficult to distinguish from p-cresol)108-39-40.775.6p-Cresol

(difficult to distinguish from m-cresol)106-44-50.775.6Cyclohexanone108-94-

10.36NA1,2-Dibromo-3-chloropropane96-12-80.1115Ethylene dibromide (1,2-

Dibromoethane)106-93-40.02815Dibromomethane74-95-30.11152,4-D (2,4-

Dichlorophenoxyacetic acid)94-75-70.7210o,pl-DDD53-19-00.0230.087p,p1-DDD72-54-

80.0230.087o,p1-DDE3424-82-60.0310.087p,p'-DDE72-55-90.0310.087o,p1-DDT789-02-

60.00390.087p,p'-DDT50-29-30.00390.087Dibenz(a,h)anthracene53-70-

30.0558.2Dibenz(a,e)pyrene192-65-40.061NAm-Dichlorobenzene541-73-10.0366.0o-

Dichlorobenzene95-50-10.0886.0p-Dichlorobenzene106-46-

---

70.0906.0Dichlorodifluoromethane75-71-80.237.21,1-Dichloroethane75-34-

30.0596.01,2-Dichloroethane107-06-20.216.01,1-Dichloroethylene75-35-

40.0256.0trans-1,2-Dichloroethylene156-60-50.054302,4-Dichloropheno1120-83-

20.044142,6-Dichloropheno187-65-00.044141,2-Dichloropropane78-87-50.8518cis-1,3-

Dichloropropylene10061-01-50.03618trans-1,3-Dichloropropylene10061-02-

60.03618Dieldrin60-57-10.0170.132,4-Dimethylaniline (2,4-xylidine)95-68-

10.0100.66Diethyl phthalate84-66-20.20282-4-Dimethyl pheno1105-67-

90.03614Dimethyl phthalate131-11-30.04728Di-n-butyl phthalate84-74-20.057281,4-

Dinitrobenzene100-25-40.322.34,6-Dinitro-o-creso1534-52-10.281602,4-

Dinitropheno151-28-50.121602,4-Dinitrotoluene121-14-20.321402,6-

Dinitrotoluene606-20-20.5528Di-n-octyl phthalate117-84-00.01728Di-n-

propylnitrosamine621-64-70.40141,4-Dioxane123-91-112.0170Diphenylamine

(difficult to distinguish from diphenylnitrosamine)122-39-

40.92NADiphenylnitrosamine (difficult to distinguish from diphenylamine)86-30-

60.92NA1,2-Diphenylhydrazine122-66-70.087NADisulfoton298-04-40.0176.2Endosulfan

I939-98-80.0230.066Endosulfan I133213-6-50.0290.13Endosulfan sulfate1031-07-

80.0290.13Endrin72-20-80.00280.13Endrin a1dehyde7421-93-40.0250.13Ethyl

acetate141-78-60.3433Ethyl cyanide (Propanenitrile)107-12-00.24360Ethyl

benzene100-41-40.05710Ethyl ether60-29-70.12160bis(2-Ethylhexyl) phthalate117-

81-70.2828Ethyl methacrylate97-63-20.14160Ethylene oxide75-21-80.12NAFamphur52-

85-70.01715Fluoranthene206-44-00.0683.4Fluorene86-73-70.0593.4Heptachlor76-44-

80.00120.0661,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-

HpCDD)35822-46-90.0000350.00251,2,3,4,6,7,8-Heptachlorodibenzofuran

(1,2,3,4,6,7,8-HpCDF)67562-39-40.0000350.00251,2,3,4,7,8,9-

Heptachlorodibenzofuran (1,2,3,4,7,8,9-HpCDF)55673-89-70.0000350.0025Heptachlor

epoxide1024-57-30.0160.066Hexachlorobenzene118-74-10.05510Hexachlorobutadiene87-

68-30.0555.6Hexachlorocyclopentadiene77-47-40.0572.4HxCDDs (All

Hexachlorodibenzo-p-dioxins)NA0.0000630.001HxCDFs (All

Hexachlorodibenzofurans)55684-94-10.0000630.001Hexachloroethane67-72-

10.05530Hexachloropropylene1888-71-70.03530Indeno (1,2,3-c,d) pyrene193-39-

50.00553.41odomethane74-88-40.19651sobutyl alcohol78-83-15.61701sodrin465-73-

60.0210.066Isosafrole120-58-10.0812.6Kepone143-50-

80.00110.13Methacrylonitrile126-98-70.2484Methano167-56-15.6NAMethapyrilene91-

80-50.0811.5Methoxychlor72-43-50.250.183-Methylcholanthrene56-49-50.0055154,4-

Methylene bis(2-chloroaniline)101-14-40.5030Methylene chloride75-09-

20.08930Methyl ethyl ketone78-93-30.2836Methyl isobutyl ketone108-10-

10.1433Methyl methacrylate80-62-60.14160Methyl methansulfonate66-27-

30.018NAMethyl parathion298-00-00.0144.6Naphthalene91-20-30.0595.62-

Naphthylamine91-59-80.52NAp-Nitroaniline100-01-60.02828Nitrobenzene98-95-

30.068145-Nitro-o-toluidine99-55-80.3228p-Nitropheno1100-02-70.1229N-

Nitrosodiethylamine55-18-50.4028N-Nitrosodimethylamine62-75-90.40NAN-Nitroso-di-

n-butylamine924-16-30.4017N-Nitrosomethylethylamine10595-95-60.402.3N-

Nitrosomorpholine59-89-20.402.3N-Nitrosopiperidine100-75-40.01335N-

Nitrosopyrrolidine930-55-20.013351,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin

(1,2,3,4,6,7,8,9-0CDD)3268-87-90.0000630.0025Parathion56-38-20.0144.6Total PCBs

(sum of all PCB isomers, or all Aroclors)1336-36-30.1010Pentachlorobenzene608-

93-50.05510PeCDDs (All Pentachlorodibenzo-p-dioxins)36088-22-

90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-

40.0000350.001Pentachloronitrobenzene82-68-80.0554.8Pentachloropheno187-86-

50.0897.4Phenacetin62-44-20.08116Phenanthrene85-01-80.0595.6Pheno1108-95-

20.0396.21,3-Phenylenediamine108-45-20.0100.66Phorate298-02-20.0214.6Phthalic

anhydride85-44-90.055NAPronamide23950-58-50.0931.5Pyrene129-00-

00.0678.2Pyridine110-86-10.01416Safrole94-59-70.08122Silvex (2,4,5-TP)93-72-

10.727.92,4,5-T93-76-50.727.91,2,4,5-Tetrachlorobenzene95-94-30.05514TCDDs (All

Tetrachlorodibenzo-p-dioxins)41903-57-50.0000630.001TCDFs (All

Tetrachlorodibenzofurans)55722-27-50.0000630.0011,1,1,2-Tetrachloroethane630-20-

60.0576.01,1,2,2-Tetrachloroethane79-34-60.0576.0Tetrachloroethylene127-18-

---

40.0566.02,3,4,6-Tetrachloropheno158-90-20.0307.4Toluene108-88-

30.08010Toxaphene8001-35-20.00952.6Bromoform (Tribromomethane)75-25-

20.63151,2,4-Trichlorobenzene120-82-10.055191,1,1-Trichloroethane71-55-

60.0546.01,1,2-Trichloroethane79-00-50.0546.0Trichloroethylene79-01-

60.0546.0Trichloromonofluoromethane75-69-40.020302,4,5-Trichloropheno195-95-

40.187.42,4,6-Trichloropheno188-06-20.0357.41,2,3-Trichloropropane96-18-

40.85301,1,2-Trichloro-1,2,2-trifluoroethane76-13-10.05730tris(2,3-

Dibromopropyl) phosphate126-72-70.11NAVinyl chloride75-01-40.276.0Xylenes-mixed

isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Antimony7440-36-

01.91.15 mg/1 TCLPArsenic7440-38-21.45.0 mg/1 TCLPBarium7440-39-31.221 mg/1

TCLPBeryllium7440-41-70.82NACadmium7440-43-90.690.11 mg/1 TCLPChromium

(Total)7440-47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Cyanides

(Amenable)757-12-50.86NAFluoride16964-48-835NALead7439-92-10.690.75 mg/1

TCLPMercury7439-97-60.150.025 mg/1 TCLPNicke17440-02-03.9811 mg/1

TCLPSelenium7782-49-20.825.7 mg/1 TCLPSilver7440-22-40.430.14 mg/1

TCLPSulfide8496-25-814NAThallium7440-28-01.4NAVanadium7440-62-24.3NA

K001

Bottom sediment sludge from the treatment of wastewaters from wood preserving

processes that use creosote or pentachlorophenol.

Naphthalene91-20-30.0595.6Pentachloropheno187-86-50.0897.4Phenanthrene85-01-

80.0595.6Pyrene129-00-00.0678.2Toluene108-88-30.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Lead7439-92-10.690.75

mg/1 TCLP

K002

Wastewater treatment sludge from the production of chrome yellow and orange

pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K003

Wastewater treatment sludge from the production of molybdate orange pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K004

Wastewater treatment sludge from the production of zinc yellow pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K005

Wastewater treatment sludge from the production of chrome green pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1

TCLPCyanides (Total)757-12-51.2590

K006

Wastewater treatment sludge from the production of chrome oxide green pigments

(anhydrous).

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K006

---

Wastewater treatment sludge from the production of chrome oxide green pigments

(hydrated).

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.69NA

K007

Wastewater treatment sludge from the production of iron blue pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1

TCLPCyanides (Total)757-12-51.2590

K008

Oven residue from the production of chrome oxide green pigments.

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K009

Distillation bottoms from the production of acetaldehyde from ethylene.

Chloroform67-66-30.0466.0

K010

Distillation side cuts from the production of acetaldehyde from ethylene.

Chloroform67-66-30.0466.0

K011

Bottom stream from the wastewater stripper in the production of acrylonitrile.

Acetonitrile75-05-85.638Acrylonitrile107-13-10.2484Acrylamide79-06-

11923Benzene71-43-20.1410Cyanide (Total)57-12-51.2590

K013

Bottom stream from the acetonitrile column in the production of acrylonitrile.

Acetonitrile75-05-85.638Acrylonitrile107-13-10.2484Acrylamide79-06-

11923Benzene71-43-20.1410Cyanide (Total)57-12-51.2590

K014

Bottoms from the acetonitrile purification column in the production of

acrylonitrile.

Acetonitrile75-05-85.638Acrylonitrile107-13-10.2484Acrylamide79-06-

11923Benzene71-43-20.1410Cyanide (Total)57-12-51.2590

K015

Still bottoms from the distillation of benzyl chloride.

Anthracene120-12-70.0593.4Benzal chloride98-87-30.0556. 0Benzo(b)fluoranthene

(difficult to distinguish from benzo(k)fluoranthene)205-99-

20.116.8Benzo(k)fluoranthene (difficult to distinguish from

benzo(b)fluoranthene)207-08-90.116.8Phenanthrene85-01-80.0595.6Toluene108-88-

30.08010Chromium (Total)7440-47-32.770.60 mg/1 TCLPNicke17440-02-03.9811 mg/1

TCLP

K016

Heavy ends or distillation residues from the production of carbon tetrachloride.

---

Hexachlorobenzene118-74-10.05510Hexachlorobutadiene87-68-

30.0555.6Hexachlorocyclopentadiene77-47-40.0572.4Hexachloroethane67-72-

10.05530Tetrachloroethylene127-18-40.0566.0

K017

Heavy ends (still bottoms) from the purification column in the production of

epichlorohydrin.

bis(2-Chloroethyl)ether111-44-40.0336.01,2-Dichloropropane78-87-50.85181,2,3-

Trichloropropane96-18-40.8530

K018

Heavy ends from the fractionation column in ethyl chloride production.

Chloroethane75-00-30.276.0Chloromethane74-87-30.19NA1,1-Dichloroethane75-34-

30.0596.01,2-Dichloroethane107-06-20.216.0Hexachlorobenzene118-74-

10.05510Hexachlorobutadiene87-68-30.0555.6Hexachloroethane67-72-

10.05530Pentachloroethane76-01-7NA6.01,1,1-Trichloroethane71-55-60.0546.0

K019

Heavy ends from the distillation of ethylene dichloride in ethylene dichloride

production.

bis(2-Chloroethyl)ether111-44-40.0336.0Chlorobenzene108-90-

70.0576.0Chloroform67-66-30.0466.0p-Dichlorobenzene106-46-70.090NA1,2-

Dichloroethane107-06-20.216.0Fluorene86-73-70.059NAHexachloroethane67-72-

10.05530Naphthalene91-20-30.0595.6Phenanthrene85-01-80.0595.61,2,4,5-

Tetrachlorobenzene95-94-30.055NATetrachloroethylene127-18-40.0566.01,2,4-

Trichlorobenzene120-82-10.055191,1,1-Trichloroethane71-55-60.0546.0

K020

Heavy ends from the distillation of vinyl chloride in vinyl chloride monomer

production.

1,2-Dichloroethane107-06-20.216.01,1,2,2-Tetrachloroethane79-34-

60.0576.0Tetrachloroethylene127-18-40.0566.0

K021

Aqueous spent antimony catalyst waste from fluoromethanes production.

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-30.0466.0Antimony7440-36-

01.91.15 mg/1 TCLP

K022

Distillation bottom tars from the production of phenol or acetone from cumene.

Toluene108-88-30.08010Acetophenone96-86-20.0109.7Diphenylamine (difficult to

distinguish from diphenylnitrosamine)122-39-40.9213Diphenylnitrosamine

(difficult to distinguish from diphenylamine)86-30-60.9213Pheno1108-95-

20.0396.2Chromium (Total)7440-47-32.770.60 mg/1 TCLPNicke17440-02-03.9811 mg/1

TCLP

K023

Distillation light ends from the production of phthalic anhydride from

naphthalene.

---

Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)100-21-

00.05528Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)85-

44-90.05528

K024

Distillation bottoms from the production of phthalic anhydride from naphthalene.

Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)100-21-

00.05528Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)85-

44-90.05528

K025

Distillation bottoms from the production of nitrobenzene by the nitration of

benzene.

NANALLEXT fb SSTRP fb CARBN; or CMBSTCMBST

K026

Stripping still tails from the production of methyl ethyl pyridines.

NANACMBSTCMBST

K027

Centrifuge and distillation residues from toluene diisocyanate production.

NANACARBN; or CMBSTCMBST

K028

Spent catalyst from the hydrochlorinator reactor in the production of 1,1,1-

trichloroethane.

1,1-Dichloroethane75-34-30.0596.0trans-1,2-Dichloroethylene156-60-

50.05430Hexachlorobutadiene87-68-30.0555.6Hexachloroethane67-72-

10.05530Pentachloroethane76-01-7NA6.01,1,1,2-Tetrachloroethane630-20-

60.0576.01,1,2,2-Tetrachloroethane79-34-60.0576.0Tetrachloroethylene127-18-

40.0566.01,1,1-Trichloroethane71-55-60.0546.01,1,2-Trichloroethane79-00-

50.0546.0Cadmium7440-43-90.69NAChromium(Total)7440-47-32.770.60 mg/1

TCLPLead7439-92-10.690.75 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLP

K029

Waste from the product steam stripper in the production of 1,1,1-

trichloroethane.

Chloroform67-66-30.0466.01,2-Dichloroethane107-06-20.216.01,1-

Dichloroethylene75-35-40.0256.01,1,1-Trichloroethane71-55-60.0546.0Vinyl

chloride75-01-40.276.0

K030

Column bodies or heavy ends from the combined production of trichloroethylene

and perchloroethylene.

o-Dichlorobenzene95-50-10.088NAp-Dichlorobenzene106-46-

70.090NAHexachlorobutadiene87-68-30.0555.6Hexachloroethane67-72-

10.05530Hexachloropropylene1888-71-7NA30Pentachlorobenzene608-93-

5NA10Pentachloroethane76-01-7NA6.01,2,4,5-Tetrachlorobenzene95-94-

30.05514Tetrachloroethylene127-18-40.0566.01,2,4-Trichlorobenzene120-82-10.05519

K031

---

By-product salts generated in the production of MSMA and cacodylic acid.

Arsenic7440-38-21.45.0 mg/1 TCLP

K032

Wastewater treatment sludge from the production of chlordane.

Hexachlorocyclopentadiene77-47-40.0572.4Chlordane ( and ? isomers)57-74-

90.00330.26Heptachlor76-44-80.00120.066Heptachlor epoxide1024-57-30.0160.066

K033

Wastewater and scrub water from the chlorination of cyclopentadiene in the

production of chlordane.

Hexachlorocyclopentadiene77-47-40.0572.4

K034

Filter solids from the filtration of hexachlorocyclopentadiene in the production

of chlordane.

Hexachlorocyclopentadiene77-47-40.0572.4

K035

Wastewater treatment sludges generated in the production of creosote.

Acenaphthene83-32-9NA3.4Anthracene120-12-7NA3.4Benz(a)anthracene56-55-

30.0593.4Benzo(a)pyrene50-32-80.0613.4Chrysene218-01-90.0593.4o-Creso195-48-

70.115.6m-Cresol

(difficult to distinguish from p-cresol)108-39-40.775.6p-Cresol

(difficult to distinguish from m-cresol)106-44-50.775.6Dibenz(a,h)anthracene53-

70-3NA8.2Fluoranthene206-44-00.0683.4Fluorene86-73-7NA3.41ndeno(1,2,3-

cd)pyrene193-39-5NA3.4Naphthalene91-20-30.0595.6Phenanthrene85-01-

80.0595.6Pheno1108-95-20.0396.2Pyrene129-00-00.0678.2

K036

Still bottoms from toluene reclamation distillation in the production of

disulfoton.

Disulfoton298-04-40.0176.2

K037

Wastewater treatment sludges from the production of disulfoton.

Disulfoton298-04-40.0176.2Toluene108-88-30.08010

K038

Wastewater from the washing and stripping of phorate production.

Phorate298-02-20.0214.6

K039

Filter cake from the filtration of diethylphosphorodithioic acid in the

production of phorate.

NANACARBN; or CMBSTCMBST

K040

---

Wastewater treatment sludge from the production of phorate.

Phorate298-02-20.0214.6

K041

Wastewater treatment sludge from the production of toxaphene.

Toxaphene8001-35-20.00952.6

K042

Heavy ends or distillation residues from the distillation of tetrachlorobenzene

in the production of 2,4,5-T.

o-Dichlorobenzene95-50-10.0886.0p-Dichlorobenzene106-46-

70.0906.0Pentachlorobenzene608-93-50.055101,2,4,5-Tetrachlorobenzene95-94-

30.055141,2,4-Trichlorobenzene120-82-10.05519

K043

2,6-Dichlorophenol waste from the production of 2,4-D.

2,4-Dichloropheno1120-83-20.044142,6-Dichloropheno1187-65-00.044142,4,5-

Trichloropheno195-95-40.187.42,4,6-Trichloropheno188-06-20.0357.42,3,4,6-

Tetrachloropheno158-90-20.0307.4Pentachloropheno187-86-

50.0897.4Tetrachloroethylene127-18-40.0566.0HxCDDs (All Hexachlorodibenzo-p-

dioxins)NA0.0000630.001HxCDFs (All Hexachlorodibenzofurans)55684-94-

10.0000630.001PeCDDs (All Pentachlorodibenzo-p-dioxins)36088-22-

90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-40.0000350.001TCDDs

(All Tetrachlorodibenzo-p-dioxins)41903-57-50.0000630.001TCDFs (All

Tetrachlorodibenzofurans)55722-27-50.0000630.001

K044

Wastewater treatment sludges from the manufacturing and processing of

explosives.

NANADEACTDEACT

K045

Spent carbon from the treatment of wastewater containing explosives.

NANADEACTDEACT

K046

Wastewater treatment sludges from the manufacturing, formulation and loading of

lead-based initiating compounds.

Lead7439-92-10.690.75 mg/1 TCLP

K047

Pink or red water from TNT operations.

NANADEACTDEACT

K048

Dissolved air flotation (DAF) float from the petroleum refining industry.

---

Benzene71-43-20.1410Benzo(a)pyrene50-32-80.0613.4bis(2-Ethylhexyl) phthalate117-

81-70.2828Chrysene218-01-90.0593.4Di-n-butyl phthalate84-74-

20.05728Ethylbenzene100-41-40.05710Fluorene86-73-70.059NANaphthalene91-20-

30.0595.6Phenanthrene85-01-80.0595.6Pheno1108-95-20.0396.2Pyrene129-00-

00.0678.2Toluene108-88-330.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Chromium (Total)7440-

47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Lead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

K049

Slop oil emulsion solids from the petroleum refining industry.

Anthracene120-12-70.0593.4Benzene71-43-20.1410Benzo(a)pyrene50-32-

80.0613.4bis(2-Ethylhexyl) phthalate117-81-70.2828Carbon disulfide75-15-

03.8NAChrysene2218-01-90.0593.42,4-Dimethylpheno1105-67-90.036NAEthylbenzene100-

41-40.05710Naphthalene91-20-30.0595.6Phenanthrene85-01-80.0595.6Pheno1108-95-

20.0396.2Pyrene129-00-00.0678.2Toluene108-88-30.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Cyanides (Total)757-

12-51.2590Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

K050

Heat exchanger bundle cleaning sludge from the petroleum refining industry.

Benzo(a)pyrene50-32-80.0613.4Pheno1108-95-20.0396.2Cyanides (Total)757-12-

51.2590Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.69NANicke17440-

02-0NAll mg/1 TCLP

K051

API separator sludge from the petroleum refining industry.

Acenaphthene83-32-90.059NAAnthracene120-12-70.0593.4Benz(a)anthracene56-55-

30.0593.4Benzene71-43-20.1410Benzo(a)pyrene50-32-80.0613.4bis(2-Ethylhexyl)

phthalate117-81-70.2828Chrysene2218-01-90.0593.4Di-n-butyl phthalate105-67-

90.05728Ethylbenzene100-41-40.05710Fluorene86-73-70.059NANaphthalene91-20-

30.0595.6Phenanthrene85-01-80.0595.6Pheno1108-95-20.0396.2Pyrene129-00-

00.0678.2Toluene108-88-30.0810Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Cyanides (Total)757-

12-51.2590Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

K052

Tank bottoms (leaded) from the petroleum refining industry.

Benzene71-43-20.1410Benzo(a)pyrene50-32-80.0613.4o-Creso195-48-70.115.6m-Cresol

(difficult to distinguish from p-cresol)108-39-40.775.6p-Cresol

(difficult to distinguish from m-cresol)106-44-50.775.62,4-Dimethylpheno1105-67-

90.036NAEthylbenzene100-41-40.05710Naphthalene91-20-30.0595.6Phenanthrene85-01-

80.0595.6Pheno1108-95-20.0396.2Toluene108-88-30.0810Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Chromium (Total)7440-

47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Lead7439-92-

10.69NANicke17440-02-0NAll mg/1 TCLP

K060

Ammonia still lime sludge from coking operations.

---

Benzene71-43-20.1410Benzo(a)pyrene50-32-80.0613.4Naphthalene91-20-

30.0595.6Pheno1108-95-20.0396.2Cyanides (Total)757-12-51.2590

K061

Emission control dust or sludge from the primary production of steel in electric

furnaces.

Antimony7440-36-0NA1.15 mg/1 TCLPArsenic7440-38-2NA5.0 mg/1 TCLPBarium7440-39-

3NA21 mg/1 TCLPBeryllium7440-41-7NA1.22 mg/1 TCLPCadmium7440-43-90.690.11 mg/1

TCLPChromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1

TCLPMercury7439-97-6NA0.025 mg/1 TCLPNicke17440-02-03.9811 mg/1

TCLPSelenium7782-49-2NA5.7 mg/1 TCLPSilver7440-22-4NA0.14 mg/1 TCLPThallium7440-

28-0NA0.20 mg/1 TCLPZinc7440-66-6NA4.3 mg/1 TCLP

K062

Spent pickle liquor generated by steel finishing operations of facilities within

the iron and steel industry (SIC Codes 331 and 332).

Chromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1

TCLPNicke17440-02-03.98NA

K069

Emission control dust or sludge from secondary lead smelting - Calcium sulfate

(Low Lead) Subcategory.

Cadmium7440-43-90.690.11 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLP

K069

Emission control dust or sludge from secondary lead smelting - Non-Calcium

sulfate (High Lead) Subcategory.

NANANARLEAD

K071

K071 (Brine purification muds from the mercury cell process in chlorine

production, where separately prepurified brine is not used) nonwastewaters that

are residues from RMERC.

Mercury7439-97-6NA0.20 mg/1 TCLP

K071

K071 (Brine purification muds from the mercury cell process in chlorine

production, where separately prepurified brine is not used) nonwastewaters that

are not residues from RMERC.

Mercury7439-97-6NA0.025 mg/1 TCLP

K071

All K071 wastewaters.

Mercury7439-97-60.15NA

K073

Chlorinated hydrocarbon waste from the purification step of the diaphragm cell

process using graphite anodes in chlorine production.

---

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-30.0466.0Hexachloroethane67-

72-10.05530Tetrachloroethylene127-18-40.0566.01,1,1-Trichloroethane71-55-

60.0546.0

K083

Distillation bottoms from aniline production.

Aniline62-53-30.8114Benzene71-43-20.1410Cyclohexanone108-94-10.36NADiphenylamine

(difficult to distinguish from diphenylnitrosamine)122-39-

40.9213Diphenylnitrosamine (difficult to distinguish from diphenylamine)86-30-

60.9213Nitrobenzene98-95-30.06814Pheno1108-95-20.0396.2Nicke17440-02-03.9811

mg/1 TCLP

K084

Wastewater treatment sludges generated during the production of veterinary

pharmaceuticals from arsenic or organo-arsenic compounds.

Arsenic7440-38-21.45.0 mg/1 TCLP

K085

Distillation or fractionation column bottoms from the production of

chlorobenzenes.

Benzene71-43-20.1410Chlorobenzene108-90-70.0576.0m-Dichlorobenzene541-73-

10.0366.0o-Dichlorobenzene95-50-10.0886.0p-Dichlorobenzene106-46-

70.0906.0Hexachlorobenzene118-74-10.05510Total PCBs

(sum of all PCB isomers, or all Aroclors)1336-36-30.1010Pentachlorobenzene608-

93-50.055101,2,4,5-Tetrachlorobenzene95-94-30.055141,2,4-Trichlorobenzene120-82-

10.05519

K086

Solvent wastes and sludges, caustic washes and sludges, or water washes and

sludges from cleaning tubs and equipment used in the formulation of ink from

pigments, driers, soaps, and stabilizers containing chromium and lead.

Acetone67-64-10.28160Acetophenone96-86-20.0109.7bis(2-Ethylhexyl) phthalate117-

81-70.2828n-Butyl alcohol71-36-35.62.6Butylbenzyl phthalate85-68-

70.01728Cyclohexanone108-94-10.36NAo-Dichlorobenzene95-50-10.0886.0Diethyl

phthalate84-66-20.2028Dimethyl phthalate131-11-30.04728Di-n-butyl phthalate84-

74-20.05728Di-n-octyl phthalate117-84-00.01728Ethyl acetate141-78-

60.3433Ethylbenzene100-41-40.05710Methano167-56-15.6NAMethyl ethyl ketone78-93-

30.2836Methyl isobutyl ketone108-10-10.1433Methylene chloride75-09-

20.08930Naphthalene91-20-30.0595.6Nitrobenzene98-95-30.06814Toluene108-88-

30.080101,1,1-Trichloroethane71-55-60.0546.0Trichloroethylene79-01-

60.0546.0Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Chromium (Total)7440-

47-32.770.60 mg/1 TCLPCyanides (Total)757-12-51.2590Lead7439-92-10.690.75 mg/1

TCLP

K087

Decanter tank tar sludge from coking operations.

Acenaphthylene208-96-80.0593.4Benzene71-43-20.1410Chrysene218-01-

90.0593.4Fluoranthene206-44-00.0683.41ndeno(1,2,3-cd)pyrene193-39-

50.00553.4Naphthalene91-20-30.0595.6Phenanthrene85-01-80.0595.6Toluene108-88-

30.08010Xylenes-mixed isomers

---

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Lead7439-92-10.690.75

mg/1 TCLP

K088

Spent potliners from primary aluminum reduction.

Acenaphthene83-32-90.0593.4Anthracene120-12-70.0593.4Benz(a)anthracene56-55-

30.0593.4Benzo(a)pyrene50-32-80.0613.4Benzo(b)fluoranthene205-99-

20.116.8Benzo(k)fluoranthene207-08-90.116.8Benzo(g,h,i)perylene191-24-

20.00551.8Chrysene218-01-90.0593.4Dibenz(a,h)anthracene53-70-

30.0558.2Fluoranthene206-44-00.0683.4Indeno(1,2,3 c,d)pyrcncIndcno(1,2,31, 2, 3-

cd)pyrene

193-39-50.00553.4Phenanthrene85-01-80.0595.6Pyrene129-00-00.0678.2Antimony7440-

36-01.91.15 mg/1 TCLPArsenic7440-38-21.426.1 mg/lBarium7440-39-31.221 mg/1

TCLPBeryllium7440-41-70.821.22 mg/1 TCLPCadmium7440-43-90.690.11 mg/1

TCLPChromium (Total)7440-47-32.770.60 mg/1 TCLPLead7439-92-10.690.75 mg/1

TCLPMercury7439-97-60.150.025 mg/1 TCLPNicke17440-02-03.9811 mg/1

TCLPSelenium7782-49-20.825.7 mg/1 TCLPSilver7440-22-40.430.14 mg/1 TCLPCyanide

(Total)757-12-51.2590Cyanide (Amenable)757-12-50.8630Fluoride16984-48-835NA

K093

Distillation light ends from the production of phthalic anhydride from ortho-

xylene.

Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)100-21-

00.05528Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)85-

44-90.05528

K094

Distillation bottoms from the production of phthalic anhydride from ortho-

xylene.

Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)100-21-

00.05528Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)85-

44-90.05528

K095

Distillation bottoms from the production of 1,1,1-trichloroethane.

Hexachloroethane67-72-10.05530Pentachloroethane76-01-70.0556.01,1,1,2-

Tetrachloroethane630-20-60.0576.01,1,2,2-Tetrachloroethane79-34-

60.0576.0Tetrachloroethylene127-18-40.0566.01,1,2-Trichloroethane79-00-

50.0546.0Trichloroethylene79-01-60.0546.0

K096

Heavy ends from the heavy ends column from the production of 1,1,1-

trichloroethane.

m-Dichlorobenzene541-73-10.0366.0Pentachloroethane76-01-70.0556.01,1,1,2-

Tetrachloroethane630-20-60.0576.01,1,2,2-Tetrachloroethane79-34-

60.0576.0Tetrachloroethylene127-18-40.0566.01,2,4-Trichlorobenzene120-82-

10.055191,1,2-Trichloroethane79-00-50.0546.0Trichloroethylene79-01-60.0546.0

K097

Vacuum stripper discharge from the chlordane chlorinator in the production of

chlordane.

---

Chlordane ( and isomers)57-74-90.00330.26Heptachlor76-44-80.00120.066Heptachlor

epoxide1024-57-30.0160.066Hexachlorocyclopentadiene77-47-40.0572.4

K098

Untreated process wastewater from the production of toxaphene.

Toxaphene8001-35-20.00952.6

K099

Untreated wastewater from the production of 2,4-D.

2,4-Dichlorophenoxyacetic acid94-75-70.7210HxCDDs (All Hexachlorodibenzo-p-

dioxins)NA0.0000630.001HxCDFs (All Hexachlorodibenzofurans)55684-94-

10.0000630.001PeCDDs (All Pentachlorodibenzo-p-dioxins)36088-22-

90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-40.0000350.001TCDDs

(All Tetrachlorodibenzo-p-dioxins)41903-57-50.0000630.001TCDFs (All

Tetrachlorodibenzofurans)55722-27-50.0000630.001

K100

Waste leaching solution from acid leaching of emission control dust or sludge

from secondary lead smelting.

Cadmium7440-43-90.690.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPLead7439-92-10.690.75 mg/1 TCLP

K101

Distillation tar residues from the distillation of aniline-based compounds in

the production of veterinary pharmaceuticals from arsenic or organo-arsenic

compounds.

o-Nitroaniline88-74-40.2714Arsenic7440-38-21.45.0 mg/1 TCLPCadmium7440-43-

90.69NALead7439-92-10.69NAMercury7439-97-60.15NA

K102

Residue from the use of activated carbon for decolorization in the production of

veterinary pharmaceuticals from arsenic or organo-arsenic compounds.

o-Nitropheno188-75-50.02813Arsenic7440-38-21.45.0 mg/1 TCLPCadmium7440-43-

90.69NALead7439-92-10.69NAMercury7439-97-60.15NA

K103

Process residues from aniline extraction from the production of aniline.

Aniline62-53-30.8114Benzene71-43-20.14102,4-Dinitropheno151-28-

50.12160Nitrobenzene98-95-30.06814Pheno1108-95-20.0396.2

K104

Combined wastewater streams generated from nitrobenzene or aniline production.

Aniline62-53-30.8114Benzene71-43-20.14102,4-Dinitropheno151-28-

50.12160Nitrobenzene98-95-30.06814Pheno1108-95-20.0396.2Cyanides (Total)757-12-

51.2590

K105

Separated aqueous stream from the reactor product washing step in the production

of chlorobenzenes.

---

Benzene71-43-20.1410Chlorobenzene108-90-70.0576.02-Chloropheno195-57-80.0445.70-

Dichlorobenzene95-50-10.0886.0p-Dichlorobenzene106-46-70.0906.0Pheno1108-95-

20.0396.22,4,5-Trichloropheno195-95-40.187.42,4,6-Trichloropheno188-06-20.0357.4

K106

K106 (wastewater treatment sludge from the mercury cell process in chlorine

production) nonwastewaters that contain greater than or equal to 260 mg/kg total

mercury.

Mercury7439-97-6NARMERC

K106

K106 (wastewater treatment sludge from the mercury cell process in chlorine

production) nonwastewaters that contain less than 260 mg/kg total mercury that

are residues from RMERC.

Mercury7439-97-6NA0.20 mg/1 TCLP

K106

Other K106 nonwastewaters that contain less than 260 mg/kg total mercury and are

not residues from RMERC.

Mercury7439-97-6NA0.025 mg/1 TCLP

K106

All K106 wastewaters.

Mercury7439-97-60.15NA

K107

Column bottoms from product separation from the production of 1,1-

dimethylhydrazine (UDMH) from carboxylic acid hydrazides.

NANACMBST; or CHOXD fb CARBN; or BIODG fb CARBNCMBST

K108

Condensed column overheads from product separation and condensed reactor vent

gases from the production of 1,1-dimethylhydrazine (UDMH) from carboxylic acid

hydrazides.

NANACMBST; or CHOXD fb CARBN; or BIODG fb CARBNCMBST

K109

Spent filter cartridges from product purification from the production of 1,1-

dimethylhydrazine (UDMH) from carboxylic acid hydrazides.

NANACMBST; or CHOXD fb CARBN; or BIODG fb CARBNCMBST

K110

Condensed column overheads from intermediate separation from the production of

1,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides.

NANACMBST; or CHOXD fb CARBN; or BIODG fb CARBNCMBST

K111

Product washwaters from the production of dinitrotoluene via nitration of

toluene.

---

2,4-Dinitrotoluene121-1 1121 14 20.321402,G2

0.321402,6-Dinitrotoluene606-20-20.5528

K112

Reaction by-product water from the drying column in the production of

toluenediamine via hydrogenation of dinitrotoluene.

NANACMBST; or CHOXD fb CARBN; or BIODG fb CARBNCMBST

K113

Condensed liquid light ends from the purification of toluenediamine in the

production of toluenediamine via hydrogenation of dinitrotoluene.

NANACARBN; or CMBSTCMBST

K114

Vicinals from the purification of toluenediamine in the production of

toluenediamine via hydrogenation of dinitrotoluene.

NANACARBN; or CMBSTCMBST

K115

Heavy ends from the purification of toluenediamine in the production of

toluenediamine via hydrogenation of dinitrotoluene.

Nicke17440-02-03.9811 mg/1 TCLPNANACARBN; or CMBSTCMBST

K116

Organic condensate from the solvent recovery column in the production of toluene

diisocyanate via phosgenation of toluenediamine.

NANACARBN; or CMBSTCMBST

K117

Wastewater from the reactor vent gas scrubber in the production of ethylene

dibromide via bromination of ethene.

Methyl bromide (Bromomethane)74-83-90.1115Chloroform67-66-30.0466.0Ethylene

dibromide (1,2-Dibromoethane)106-93-40.02815

K118

Spent absorbent solids from purification of ethylene dibromide in the production

of ethylene dibromide via bromination of ethene.

Methyl bromide (Bromomethane)74-83-90.1115Chloroform67-66-30.0466.0Ethylene

dibromide (1,2-Dibromoethane)106-93-40.02815

K123

Process wastewater (including supernates, filtrates, and washwaters) from the

production of ethylenebisdithiocarbamic acid and its salts.

NANACMBST; or CHOXD fb (BIODG or CARBN)CMBST

K124

Reactor vent scrubber water from the production of ethylenebisdithiocarbamic

acid and its salts.

---

NANACMBST; or CHOXD fb (BIODG or CARBN)CMBST

K125

Filtration, evaporation, and centrifugation solids from the production of

ethylenebisdithiocarbamic acid and its salts.

NANACMBST; or CHOXD fb (BIODG or CARBN)CMBST

K126

Baghouse dust and floor sweepings in milling and packaging operations from the

production or formulation of ethylenebisdithiocarbamic acid and its salts.

NANACMBST; or CHOXD fb (BIODG or CARBN)CMBST

K131

Wastewater from the reactor and spent sulfuric acid from the acid dryer from the

production of methyl bromide.

Methyl bromide (Bromomethane)74-83-90.1115

K132

Spent absorbent and wastewater separator solids from the production of methyl

bromide.

Methyl bromide (Bromomethane)74-83-90.1115

K136

Still bottoms from the purification of ethylene dibromide in the production of

ethylene dibromide via bromination of ethene.

Methyl bromide (Bromomethane)74-83-90.1115Chloroform67-66-30.0466.0Ethylene

dibromide (1,2-Dibromoethane)106-93-40.02815

K141

Process residues from the recovery of coal tar, including, but not limited to,

collecting sump residues from the production of coke or the recovery of coke by-

products produced from coal. This listing does not include K087 (decanter tank

tar sludge from coking operations).

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-2-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-

90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Indeno(1,2,3-cd)pyrene193-39-

50.00553.4

K142

Tar storage tank residues from the production of coke from coal or from the

recovery of coke by-products produced from coal.

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-

90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Indeno(1,2,3-cd)pyrene193-39-

50.00553.4

---

K143

Process residues from the recovery of light oil, including, but not limited to,

those generated in stills, decanters, and wash oil recovery units from the

recovery of coke by-products produced from coal.

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-90.0593.4

K144

Wastewater sump residues from light oil refining, including, but not limited to,

intercepting or contamination sump sludges from the recovery of coke by-products

produced from coal.

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-

90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2

K145

Residues from naphthalene collection and recovery operations from the recovery

of coke by-products produced from coal.

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Chrysene218-01-90.0593.4Dibenz(a,h)anthracene53-70-

30.0558.2Naphthalene91-20-30.0595.6

K147

Tar storage tank residues from coal tar refining.

Benzene71-43-20.1410Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-

90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Indeno(1,2,3-cd)pyrene193-39-

50.00553.4

K148

Residues from coal tar distillation, including, but not limited to, still

bottoms.

Benz(a)anthracene56-55-30.0593.4Benzo(a)pyrene50-32-

80.0613.4Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Chrysene218-01-

90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Indeno(1,2,3-cd)pyrene193-39-

50.00553.4

K149

Distillation bottoms from the production of - (or methyl-) chlorinated toluenes,

ring-chlorinated toluenes, benzoyl chlorides, and compounds with mixtures of

these functional groups. (This waste does not include still bottoms from the

distillations of benzyl chloride.)

---

Chlorobenzene108-90-70.0576.0Chloroform67-66-30.0466.0Chloromethane74-87-

30.1930p-Dichlorobenzene106-46-70.0906.0Hexachlorobenzene118-74-

10.05510Pentachlorobenzene608-93-50.055101,2,4,5-Tetrachlorobenzene95-94-

30.05514Toluene108-88-30.08010

K150

Organic residuals, excluding spent carbon adsorbent, from the spent chlorine gas

and hydrochloric acid recovery processes associated with the production of - (or

methyl-) chlorinated toluenes, ring-chlorinated toluenes, benzoyl chlorides, and

compounds with mixtures of these functional groups.

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-30.0466.0Chloromethane74-87-

30.1930p-Dichlorobenzene106-46-70.0906.0Hexachlorobenzene118-74-

10.05510Pentachlorobenzene608-93-50.055101,2,4,5-Tetrachlorobenzene95-94-

30.055141,1,2,2- Tetrachloroethane79-34-50.0576.0Tetrachloroethylene127-18-

40.0566.01,2,4-Trichlorobenzene120-82-10.05519

K151

Wastewater treatment sludges, excluding neutralization and biological sludges,

generated during the treatment of wastewaters from the production of - (or

methyl-) chlorinated toluenes, ring-chlorinated toluenes, benzoyl chlorides, and

compounds with mixtures of these functional groups.

Benzene71-43-20.1410Carbon tetrachloride56-23-50.0576.0Chloroform67-66-

30.0466.0Hexachlorobenzene118-74-10.05510Pentachlorobenzene608-93-

50.055101,2,4,5-Tetrachlorobenzene95-94-30.05514Tetrachloroethylene127-18-

40.0566.0Toluene108-88-30.08010

K156

Organic waste (including heavy ends, still bottoms, light ends, spent solvents,

filtrates, and decantates) from the production of carbamates and carbamoyl

oximes.10

Acetonitrile75-05-85.61.8Acetophenone-9-6-98-86-2

98 86 20.0109.70 0109.7Aniline62-53-30.8114Benomy117804-35-20.0561.4Benzene71-

43-20.1410Carbary163-25-210.0060.14Carbenzadim10605-21-70.0561.4Carbofuran1563-

66-20.0060.14Carbosulfan55285-14-80.0281.4Chlorobenzene108-90-

70.0576.0Chloroform67-66-30.0466.0o-Dichlorobenzene95-50-10.0886.0Methomy116752-

77-50.0280.14Methylene chloride75-09-20.08930Methyl ethyl ketone78-93-

30.2836Naphthalene91-20-30.0595.6Pheno1108-95-20.0396.2Pyridine110-86-

10.01416Toluene108-88-30.08010Triethylamine121-44-80.0811.5

K157

Wastewaters (including scrubber waters, condenser waters, washwaters, and

separation waters) from the production of carbamates and carbamoyl oximes.

Carbon tetrachloride56-23-50.0576.0Chloroform67-66-30.0466.0Chloromethane74-87-

30.1930Methomy116752-77-50.0280.14Methylene chloride75-09-20.08930Methyl ethyl

ketone78-93-30.2836Pyridine110-86-10.01416Triethylamine121-44-80.0811.5

K158

Baghouse dusts and filter/separation solids from the production of carbamates

and carbamoyl oximes.

Benomy117804-35-20.0561.4Benzene71-43-20.1410Carbenzadim10605-21-

70.0561.4Carbofuran1563-66-20.0060.14Carbosulfan55285-14-80.0281.4Chloroform67-

66-30.0466.0Methylene chloride75-09-20.08930Pheno1108-95-20.0396.2

---

K159

Organics from the treatment of thiocarbamate wastes.10

Benzene71-43-20.1410Butylate2008-41-50.0421.4EPTC (Eptam)759-94-

40.0421.4Molinate2212-67-10.0421.4Pebulate1114-71-20.0421.4Vernolate1929-77-

70.0421.4

K161

Purification solids (including filtration, evaporation, and centrifugation

solids), baghouse dust and floor sweepings from the production of

dithiocarbamate acids and their salts.

Antimony7440-36-01.91.1511Arsenic7440-38-21.45.011Carbon disulfide75-15-

03.84.811Dithiocarbamates (total)137-30-40.02828Lead7439-92-

10.690.7511Nicke17440-02-03.981111Selenium7782-49-20.825.711

K169

Crude oil tank sediment from petroleum refining operations.

Benz(a)anthracene56-55-30.0593.4Benzene71-43-20.1410Benzo(g,h,i)perylene191-24-

20.00551.8Chrysene218-01-90.0593.4Ethyl benzene100-41-40.05710Fluorene86-73-

70.0593.4Naphthalene91-20-30.0595.6Phenanthrene81-05-80.0595.6Pyrene129-00-

00.0678.2Toluene (Methyl Benzene)108-88-30.08010Xylenes (Total)1330-20-70.3230

K170

Clarified slurry oil sediment from petroleum refining operations.

Benz(a)anthracene56-55-30.0593.4Benzene71-43-20.1410Benzo(g,h,i)perylene191-24-

20.00551.8Chrysene218-01-90.0593.4Dibenz(a,h)anthracene53-70-30.0558.2Ethyl

benzene100-41-40.05710Fluorene86-73-70.0593.4Indeno(1,2,3,-cd)pyrene193-39-

50.00553.4Naphthalene91-20-30.0595.6Phenanthrene81-05-80.0595.6Pyrene129-00-

00.0678.2Toluene (Methyl Benzene)108-88-30.08010Xylenes (Tota11330-20-70.3230

K171

Spent hydrotreating catalyst from petroleum refining operations, including guard

beds used to desulfurize feeds to other catalytic reactors. (This listing does

not include inert support media.)

Benz(a)anthracene56-55-30.0593.4Benzene71-43-20.1410Chrysene218-01-

90.0593.4Ethyl benzene100-41-40.05710Naphthalene91-20-30.0595.6Phenanthrene81-

05-80.0595.6Pyrene129-00-00.0678.2Toluene (Methyl Benzene)108-88-30.08010Xylenes

(Total)1330-20-70.3230Arsenic7740-38-21.45 mg/1 TCLPNicke17440-02-03.9811.0 mg/1

TCLPVanadium7440-62-24.31.6 mg/1 TCLPReactive sulfidesNADEACTDEACT

K172

Spent hydrorefining catalyst from petroleum refining operations, including guard

beds used to desulfurize feeds to other catalytic reactors. (This listing does

not include inert support media.)

Benzene71-43-20.1410Ethyl benzene100-41-40.05710Toluene (Methyl Benzene)108-88-

30.08010Xylenes (Total)1330-20-70.3230Antimony7740-36-01.91.15 mg/1

TCLPArsenic7740-38-21.45 mg/1 TCLPNicke17440-02-03.9811.0 mg/1 TCLPVanadium7440-

62-24.31.6 mg/1 TCLPReactive SulfidesNADEACTDEACT

K174

---

Wastewater treatment sludge from the production of ethylene dicholoride or vinyl

choloride monomer.

1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDD)35822-46-

90.000035 or CMBST110.0025 or CMBST111,2,3,4,6,7,8-Heptachlorodibenzofuran

(1,2,3,4,6,7,8-HpCDF)67562-39-40.000035 or CMBST110.0025 or

CMBST111,2,3,4,7,8,9-Heptachlorodibenzofuran (l,2,3,4,7,8,9-HpCDF)55673-89-

70.000035 or CMBST110.0025 or CMBST11A11 hexachlorodibenzo-p-dioxins

(HxCDDs)34465-46-80.000063 or CMBST110.001 or CMBST11A11 hexachlorodibenzofurans

(HxCDFs)55684-94-10.000063 or CMBST110.001 or CMBST111,2,3,4,6,7,8,9-

Octachlorodibenzo-p-dioxin (1,2,3,4,6,7,8,9-0CDD)3268-87-90.000063 or

CMBST110.005 or CMBST111,2,3,4,6,7,8,9-Octachlorodibenzofuran (1,2,3,4,6,7,8,9-

OCDF)39001-02-00.000063 or CMBST110.005 or CMBST11A11 pentachlorodibenzo-p-

dioxins (PeCDDs)36088-22-90.000063 or CMBST110.001 or CMBST11A11

pentachlorodibenzofurans (PeCDFs)30402-15-40.000035 or CMBST110.001 or

CMBST11A11 tetrachlorodibenzo-p-dioxins (TCDDs)41903-57-50.000063 or

CMBST110.001 or CMBST11A11 tetrachlorodibenzofurans (TCDFs)55722-27-50.000063 or

CMBST110.001 or CMBST1lArsenic7440-36-01.45.0 mg/1 TCLP

K175

Wastewater treatment sludge from the production of vinyl choloride monomer using

mercuric chloride catalyst in an acetylene-based process.

Mercury127439-97-6NA0.025 mg/1 TCLPPH12NApH ? 6.0

K175

All K175 wastewaters.

Mercury7439-97-60.15NA

K176

Baghouse filters from the production of antimony oxide, including filters from

the production of intermediates e.g., antimony metal or crude antimony oxide).

Antimony7440-36-01.91.15 mg/1 TCLPArsenic7440-38-21.45.0 mg/1 TCLPCadmium7440-

43-90.690.11 mg/1 TCLPLead7439-92-10.690.75 mg/1 TCLPMercury7439-97-60.150.025

mg/1 TCLP

K177

Slag from the production of antimony oxide that is speculatively accumulated or

disposed, including slag from the production of intermediates (e.g., antimony

metal or crude antimony oxide).

Antimony7440-36-01.91.15 mg/1 TCLPArsenic7440-38-21.45.0 mg/1 TCLPLead7439-92-

10.690.75 mg/1 TCLP

K178

Residues from manufacturing and manufacturing-site storage of ferric chloride

from acids formed during the production of titanium dioxide using the chloride-

ilmenite process.

1,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-HpCDD)35822-46-

90.000035 or CMBST110.0025 or CMBST111,2,3,4,6,7,8-Heptachlorodibenzofuran

(1,2,3,4,6,7,8-HpCDF)67562-39-40.000035 or CMBST110.0025 or

CMBST111,2,3,4,7,8,9-Heptachlorodibenzofuran (l,2,3,4,7,8,9-HpCDF)55673-89-

70.000035 or CMBST110.0025 or CMBST11HxCDDs (All Hexachlorodibenzo-p-

dioxins)34465-46-80.000063 or CMBST110.001 or CMBST11HxCDFs (All

---

Hexachlorodibenzofurans)55684-94-10.000063 or CMBST110.001 or

CMBST111,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin (1,2,3,4,6,7,8,9-0CDD)3268-87-

90.000063 or CMBST110.005 or CMBST111,2,3,4,6,7,8,9-Octachlorodibenzofuran

(OCDF)39001-02-00.000063 or CMBST110.005 or CMBST11PeCDDs (All

Pentachlorodibenzo-p-dioxins)36088-22-90.000063 or CMBST110.001 or CMBST11PeCDFs

(All Pentachlorodibenzofurans)30402-15-40.000035 or CMBST110.001 or CMBST11TCDDs

(All Tetrachlorodibenzo-p-dioxins)41903-57-50.000063 or CMBST110.001 or

CMBST11TCDFs (All Tetrachlorodibenzofurans)55722-27-50.000063 or CMBST110.001 or

CMBST11Thallium7440-28-01.40.20 mg/1 TCLP

K181

Nonwastewaters from the production of dyes or pigments (including nonwastewaters

commingled at the point of generation with nonwastewaters from other processes)

that, at the point of generation, contain mass loadings of any of the

constituents identified in Section 721.132(c) which are equal to or greater than

the corresponding Section 721.132(c) levels, as determined on a calendar-year

basis.

Aniline62-53-30.8114o-Anisidine (2-methoxyaniline)90-04-00.0100.664-

Chloroaniline106-47-80.4616p-Cresidine120-71-80.0100.662,4-Dimethylaniline (2,4-

xylidine)95-68-10.0100.661,2-Phenylenediamine95-54-5CMBST; or CHOXD fb (BIODG or

CARBN); or BIODG fb CARBNCMBST; or CHOXD fb (BIODG or CARBN); or BIODG fb

CARBN1,3-Phenylenediamine108-45-20.0100.66

P001

Warfarin, & salts, when present at concentrations greater than 0.3 percent.

Warfarin81-81-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P002

1-Acetyl-2-thiourea.

1-Acetyl-2-thiourea591-08-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P003

Acrolein.

Acrolein107-02-80.29CMBST

P004

Aldrin.

Aldrin309-00-20.0210.066

P005

Allyl alcohol.

Allyl alcohol107-18-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P006

Aluminum phosphide.

Aluminum phosphide20859-73-8CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

P007

5-Aminomethyl-3-isoxazolol.

5-Aminomethyl-3-isoxazolol2763-96-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

---

P008

4-Aminopyridine.

4-Aminopyridine504-24-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P009

Ammonium picrate.

Ammonium picrate131-74-8CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or

CMBST

P010

Arsenic acid.

Arsenic7440-38-21.45.0 mg/1 TCLP

P011

Arsenic pentoxide.

Arsenic7440-38-21.45.0 mg/1 TCLP

P012

Arsenic trioxide.

Arsenic7440-38-21.45.0 mg/1 TCLP

P013

Barium cyanide.

Barium7440-39-3NA21 mg/1 TCLPCyanides (Total)757-12-51.2590Cyanides

(Amenable)757-12-50.8630

P014

Thiophenol (Benzene thiol).

Thiophenol (Benzene thio1)108-98-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P015

Beryllium dust.

Beryllium7440-41-7RMETL;or RTHRMRMETL; or RTHRM

P016

Dichloromethyl ether (Bis(chloromethyl)ether).

Dichloromethyl ether542-88-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P017

Bromoacetone.

Bromoacetone598-31-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P018

Brucine.

Brucine357-57-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

---

P020

2-sec-Butyl-4,6-dinitrophenol (Dinoseb).

2-sec-Butyl-4,6-dinitrophenol (Dinoseb)88-85-70.0662.5

P021

Calcium cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P022

Carbon disulfide.

Carbon disulfide75-15-03.8CMBSTCarbon disulfide; alternate6 standard for

nonwastewaters only75-15-0NA4.8 mg/1 TCLP

P023

Chloroacetaldehyde.

Chloroacetaldehyde107-20-0(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

P024

p-Chloroaniline.

p-Chloroaniline106-47-80.4616

P026

1-(o-Chlorophenyl)thiourea.

1-(o-Chlorophenyl)thiourea5344-82-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P027

3-Chloropropionitrile.

3-Chloropropionitrile542-76-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P028

Benzyl chloride.

Benzyl chloride100-44-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P029

Copper cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P030

Cyanides (soluble salts and complexes).

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P031

Cyanogen.

Cyanogen460-19-5CHOXD; WETOX; or CMBSTCHOXD; WETOX; or CMBST

P033

---

Cyanogen chloride.

Cyanogen chloride506-77-4CHOXD; WETOX; or CMBSTCHOXD; WETOX; or CMBST

P034

2-Cyclohexy1-4,6-dinitrophenol.

2-Cyclohexy1-4,6-dinitropheno1131-89-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P036

Dichlorophenylarsine.

Arsenic7440-38-21.45.0 mg/1 TCLP

P037

Dieldrin.

Dieldrin60-57-10.0170.13

P038

Diethylarsine.

Arsenic7440-38-21.45.0 mg/1 TCLP

P039

Disulfoton.

Disulfoton298-04-40.0176.2

PO40

0,0-Diethyl-0-pyrazinyl-phosphorothioate.

0,0-Diethyl-0-pyrazinylphosphorothioate297-97-2CARBN; or CMBSTCMBST

PO41

Diethyl-p-nitrophenyl phosphate.

Diethyl-p-nitrophenyl phosphate311-45-5CARBN; or CMBSTCMBST

PO42

Epinephrine.

Epinephrine51-43-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

PO43

Diisopropylfluorophosphate (DFP).

Diisopropylfluorophosphate (DFP)55-91-4CARBN; or CMBSTCMBST

PO44

Dimethoate.

Dimethoate60-51-5CARBN; or CMBSTCMBST

PO45

Thiofanox.

---

Thiofanox39196-18-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

PO46

,-Dimethylphenethylamine.

,-Dimethylphenethylamine122-09-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

PO47

4,6-Dinitro-o-cresol.

4,6-Dinitro-o-creso1543-52-10.28160

PO47

4,6-Dinitro-o-cresol salts.

NANA(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

PO48

2,4-Dinitrophenol.

2,4-Dinitropheno151-28-50.12160

PO49

Dithiobiuret.

Dithiobiuret541-53-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P050

Endosulfan.

Endosulfan I939-98-80.0230.066Endosulfan I133213-6-50.0290.13Endosulfan

sulfate1031-07-80.0290.13

P051

Endrin.

Endrin72-20-80.00280.13Endrin aldehyde7421-93-40.0250.13

P054

Aziridine.

Aziridine151-56-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P056

Fluorine.

Fluoride (measured in wastewaters only)16964-48-835ADGAS fb NEUTR

P057

Fluoroacetamide.

Fluoroacetamide640-19-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P058

Fluoroacetic acid, sodium salt.

Fluoroacetic acid, sodium salt62-74-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

---

P059

Heptachlor.

Heptachlor76-44-80.00120.066Heptachlor epoxide1024-57-30.0160.066

P060

Isodrin.

Isodrin465-73-60.0210.066

P062

Hexaethyl tetraphosphate.

Hexaethyl tetraphosphate757-58-4CARBN; or CMBSTCMBST

P063

Hydrogen cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P064

Isocyanic acid, ethyl ester.

Isocyanic acid, ethyl ester624-83-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P065

P065 (mercury fulminate) nonwastewaters, regardless of their total mercury

content, that are not incinerator residues or are not residues from RMERC.

Mercury7439-97-6NAIMERC

P065

P065 (mercury fulminate) nonwastewaters that are either incinerator residues or

are residues from RMERC; and contain greater than or equal to 260 mg/kg total

mercury.

Mercury7339-97-6NARMERC

P065

P065 (mercury fulminate) nonwastewaters that are residues from RMERC and contain

less than 260 mg/kg total mercury.

Mercury7439-97-6NA0.20 mg/1 TCLP

P065

P065 (mercury fulminate) nonwastewaters that are incinerator residues and

contain less than 260 mg/kg total mercury.

Mercury7439-97-6NA0.025 mg/1 TCLP

P065

All P065 (mercury fulminate) wastewaters.

Mercury7439-97-60.15NA

P066

---

Methomyl.

Methomy116752-77-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P067

2-Methyl-aziridine.

2-Methyl-aziridine75-55-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P068

Methyl hydrazine.

Methyl hydrazine

60-34-4CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED, or CMBST

P069

2-Methyllactonitrile.

2-Methyllactonitrile

75-86-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P070

Aldicarb.

Aldicarb116-06-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P071

Methyl parathion.

Methyl parathion298-00-00.0144.6

P072

1-Naphthy1-2-thiourea.

1-Naphthy1-2-thiourea86-88-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P073

Nickel carbonyl.

Nicke17440-02-03.9811 mg/1 TCLP

P074

Nickel cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Nicke17440-02-

03.9811 mg/1 TCLP

P075

Nicotine and salts.

Nicotine and salts54-11-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P076

Nitric oxide.

Nitric oxide10102-43-9ADGASADGAS

P077

---

p-Nitroaniline.

p-Nitroaniline100-01-60.02828

P078

Nitrogen dioxide.

Nitrogen dioxide10102-44-0ADGASADGAS

P081

Nitroglycerin.

Nitroglycerin55-63-0CHOXD; CHRED; CARBN; BIODG or CMBSTCHOXD; CHRED; or CMBST

P082

N-Nitrosodimethylamine.

N-Nitrosodimethylamine62-75-90.402.3

P084

N-Nitrosomethylvinylamine.

N-Nitrosomethylvinylamine4549-40-0(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P085

Octamethylpyrophosphoramide.

Octamethylpyrophosphoramide152-16-9CARBN; or CMBSTCMBST

P087

Osmium tetroxide.

Osmium tetroxide20816-12-ORMETL; or RTHRMRMETL; or RTHRM

P088

Endothall.

Endothal1145-73-3(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

P089

Parathion.

Parathion56-38-20.0144.6

P092

P092 (phenyl mercuric acetate) nonwastewaters, regardless of their total mercury

content, that are not incinerator residues or are not residues from RMERC.

Mercury7439-97-6NAIMERC; or RMERC

P092

P092 (phenyl mercuric acetate) nonwastewaters that are either incinerator

residues or are residues from RMERC; and still contain greater than or equal to

260 mg/kg total mercury.

Mercury7439-97-6NARMERC

---

P092

P092 (phenyl mercuric acetate) nonwastewaters that are residues from RMERC and

contain less than 260 mg/kg total mercury.

Mercury7439-97-6NA0.20 mg/1 TCLP

P092

P092 (phenyl mercuric acetate) nonwastewaters that are incinerator residues and

contain less than 260 mg/kg total mercury.

Mercury7439-97-6NA0.025 mg/1 TCLP

P092

All P092 (phenyl mercuric acetate) wastewaters.

Mercury7439-97-60.15NA

P093

Phenylthiourea.

Phenylthiourea103-85-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P094

Phorate.

Phorate298-02-20.0214.6

P095

Phosgene.

Phosgene75-44-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P096

Phosphine.

Phosphine7803-51-2CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

P097

Famphur.

Famphur52-85-70.01715

P098

Potassium cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P099

Potassium silver cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Silver7440-22-

40.430.14 mg/1 TCLP

P101

Ethyl cyanide (Propanenitrile).

---

Ethyl cyanide (Propanenitrile)107-12-00.24360

P102

Propargyl alcohol.

Propargyl alcohol107-19-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P103

Selenourea.

Selenium7782-49-20.825.7 mg/1 TCLP

P104

Silver cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630Silver7440-22-

40.430.14 mg/1 TCLP

P105

Sodium azide.

Sodium azide26628-22-8CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or CMBST

P106

Sodium cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P108

Strychnine and salts.

Strychnine and salts57-24-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P109

Tetraethyldithiopyrophosphate.

Tetraethyldithiopyrophosphate3689-24-5CARBN; or CMBSTCMBST

P110

Tetraethyl lead.

Lead7439-92-10.690.75 mg/1 TCLP

P111

Tetraethylpyrophosphate.

Tetraethylpyrophosphate107-49-3CARBN; or CMBSTCMBST

P112

Tetranitromethane.

Tetranitromethane509-14-8CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or

CMBST

P113

Thallic oxide.

---

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

P114

Thallium selenite.

Selenium7782-49-20.825.7 mg/1 TCLP

P115

Thallium (I) sulfate.

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

P116

Thiosemicarbazide.

Thiosemicarbazide79-19-6(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

P118

Trichloromethanethiol.

Trichloromethanethiol75-70-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

P119

Ammonium vanadate.

Vanadium (measured in wastewaters only)7440-62-24.3STABL

P120

Vanadium pentoxide.

Vanadium (measured in wastewaters only)7440-62-24.3STABL

P121

Zinc cyanide.

Cyanides (Total)757-12-51.2590Cyanides (Amenable)757-12-50.8630

P122

Zinc phosphide Zn3P2, when present at concentrations greater than 10 percent.

Zinc Phosphide1314-84-7CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

P123

Toxaphene.

Toxaphene8001-35-20.00952.6

P127

Carbofuran.

Carbofuran1563-66-20.0060.14

P128

Mexacarbate.

Mexacarbate315-18-40.0561.4

P185

---

Tirpate.10

Tirpate26419-73-80.0560.28

P188

Physostigimine salicylate.

Physostigmine salicylate57-64-70.0561.4

P189

Carbosulfan.

Carbosulfan55285-14-80.0281.4

P190

Metolcarb.

Metolcarb1129-41-50.0561.4

P191

Dimetilan.10

Dimetilan644-64-40.0561.4

P192

Isolan.10

Isolan119-38-00.0561.4

P194

Oxamyl.

0xamy123135-22-00.0560.28

P196

Manganese dimethyldithiocarbamates (total).

Dithiocarbamates (total)NA0.02828

P197

Formparanate.10

Formparanate17702-57-70.0561.4

P198

Formetanate hydrochloride.

Formetanate hydrochloride23422-53-90.0561.4

P199

Methiocarb.

Methiocarb2032-65-70.0561.4

P201

Promecarb.

---

Promecarb2631-37-00.0561.4

P202

m-Cumenyl methylcarbamate.

m-Cumenyl methylcarbamate64-00-60.0561.4

P203

Aldicarb sulfone.

Aldicarb sulfone1646-88-40.0560.28

P204

Physostigmine.

Physostigmine57-47-60.0561.4

P205

Ziram.

Dithiocarbamates (total)NA0.02828

U001

Acetaldehyde.

Acetaldehyde75-07-0(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U002

Acetone.

Acetone67-64-10.28160

U003

Acetonitrile.

Acetonitrile75-05-85.6CMBSTAcetonitrile; alternate6 standard for nonwastewaters

only75-05-8NA38

U004

Acetophenone.

Acetophenone98-86-20.0109.7

U005

2-Acetylaminofluorene.

2-Acetylaminofluorene53-96-30.059140

U006

Acetyl chloride.

Acetyl chloride75-36-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U007

Acrylamide.

Acrylamide79-06-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

---

U008

Acrylic acid.

Acrylic acid79-10-7(WETOX or CHOXD)

fb

CARBN; or CMBSTCMBST

U009

Acrylonitrile.

Acrylonitrile107-13-10.2484

U010

Mitomycin C.

Mitomycin C50-07-7(WETOX or CHOXD) fb

CARBN; or CMBSTCMBST

U011

Amitrole.

Amitrole61-82-5(WETOX or CHOXD)

fb CARBN; or CMBSTCMBST

U012

Aniline.

Aniline62-53-30.8114

U014

Auramine.

Auramine492-80-8(WETOX or CHOXD)

fb

CARBN; or CMBSTCMBST

U015

Azaserine.

Azaserine115-02-6(WETOX or CHOXD)

fb

CARBN; or CMBSTCMBST

U016

Benz(c)acridine.

Benz(c)acridine225-51-4(WETOX or CHOXD)

fb

CARBN; or CMBSTCMBST

U017

Benzal chloride.

Benzal chloride98-87-3(WETOX or CHOXD) fb

CARBN; or CMBSTCMBST

U018

Benz(a)anthracene.

Benz(a)anthracene56-55-30.0593.4

U019

Benzene.

Benzene71-43-20.1410

UO20

---

Benzenesulfonyl chloride.

Benzenesulfonyl chloride98-09-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO21

Benzidine.

Benzidine92-87-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO22

Benzo(a)pyrene.

Benzo(a)pyrene50-32-80.0613.4

UO23

Benzotrichloride.

Benzotrichloride98-07-7CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or

CMBST

UO24

bis(2-Chloroethoxy)methane.

bis(2-Chloroethoxy)methane111-91-10.0367.2

UO25

bis(2-Chloroethyl)ether.

bis(2-Chloroethyl)ether111-44-40.0336.0

UO26

Chlornaphazine.

Chlornaphazine494-03-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO27

bis(2-Chloroisopropyl)ether.

bis(2-Chloroisopropyl)ether39638-32-90.0557.2

UO28

bis(2-Ethylhexyl)phthalate.

bis(2-Ethylhexyl)phthalate117-81-70.2828

UO29

Methyl bromide (Bromomethane).

Methyl bromide (Bromomethane)74-83-90.1115

UO30

4-Bromophenyl phenyl ether.

4-Bromophenyl phenyl ether101-55-30.05515

UO31

n-Butyl alcohol.

---

n-Butyl alcohol71-36-35.62.6

UO32

Calcium chromate.

Chromium (Total)7440-47-32.770.60 mg/1 TCLP

UO33

Carbon oxyfluoride.

Carbon oxyfluoride353-50-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO34

Trichloroacetaldehyde (Chloral).

Trichloroacetaldehyde (Chloral)75-87-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO35

Chlorambucil.

Chlorambuci1305-03-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

UO36

Chlordane.

Chlordane ( and isomers)57-74-90.00330.26

UO37

Chlorobenzene.

Chlorobenzene108-90-70.0576.0

UO38

Chlorobenzilate.

Chlorobenzilate510-15-60.10CMBST

UO39

p-Chloro-m-cresol.

p-Chloro-m-cresol59-50-70.01814

U041

Epichlorohydrin (1-Chloro-2,3-epoxypropane).

Epichlorohydrin (1-Chloro-2,3-epoxypropane)106-89-8(WETOX or CHOXD) fb CARBN; or

CMBSTCMBST

U042

2-Chloroethyl vinyl ether.

2-Chloroethyl vinyl ether110-75-80.062CMBST

U043

Vinyl chloride.

---

Vinyl chloride75-01-40.276.0

U044

Chloroform.

Chloroform67-66-30.0466.0

U045

Chloromethane (Methyl chloride).

Chloromethane (Methyl chloride)74-87-30.1930

U046

Chloromethyl methyl ether.

Chloromethyl methyl ether107-30-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U047

2- Chloronaphthalene.

2-Chloronaphthalene91-58-70.0555.6

U048

2-Chlorophenol.

2-Chloropheno195-57-80.0445.7

U049

4-Chloro-o-toluidine hydrochloride.

4-Chloro-o-toluidine hydrochloride3165-93-3(WETOX or CHOXD) fb CARBN; or

CMBSTCMBST

U050

Chrysene.

Chrysene218-01-90.0593.4

U051

Creosote.

Naphthalene91-20-30.0595.6Pentachloropheno187-86-50.0897.4Phenanthrene85-01-

80.0595.6Pyrene129-00-00.0678.2Toluene108-88-30.08010Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230Lead7439-92-10.690.75

mg/1 TCLP

U052

Cresols (Cresylic acid).

o-Creso195-48-70.115.6m-Cresol (difficult to distinguish from p-cresol)108-39-

40.775.6p-Cresol (difficult to distinguish from m-cresol)106-44-50.775.6Cresol-

mixed isomers (Cresylic acid)

(sum of o-, m-, and p-cresol concentrations)1319-77-30.8811.2

U053

Crotonaldehyde.

---

Crotonaldehyde4170-30-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U055

Cumene.

Cumene98-82-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U056

Cyclohexane.

Cyclohexane110-82-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U057

Cyclohexanone.

Cyclohexanone108-94-10.36CMBSTCyclohexanone; alternate6 standard for

nonwastewaters on1y108-94-1NA0.75 mg/1 TCLP

U058

Cyclophosphamide.

Cyclophosphamide50-18-0CARBN; or CMBSTCMBST

U059

Daunomycin.

Daunomycin20830-81-3(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U060

DDD.

o,p'-DDD53-19-00.0230.087p,p'-DDD72-54-80.0230.087

U061

DDT.

o,pl-DDT789-02-60.00390.087p,p1-DDT50-29-30.00390.087o,p'-DDD53-19-

00.0230.087p,p'-DDD72-54-80.0230.087o,p1-DDE3424-82-60.0310.087p,pl-DDE72-55-

90.0310.087

U062

Diallate.

Diallate2303-16-4(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U063

Dibenz(a,h)anthracene.

Dibenz(a,h)anthracene53-70-30.0558.2

U064

Dibenz(a,i)pyrene.

Dibenz(a,i)pyrene189-55-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U066

1,2-Dibromo-3-chloropropane.

---

1,2-Dibromo-3-chloropropane96-12-80.1115

U067

Ethylene dibromide (1,2-Dibromoethane).

Ethylene dibromide (1,2-Dibromoethane)106-93-40.02815

U068

Dibromomethane.

Dibromomethane74-95-30.1115

U069

Di-n-butyl phthalate.

Di-n-butyl phthalate84-74-20.05728

U070

o-Dichlorobenzene.

o-Dichlorobenzene95-50-10.0886.0

U071

m-Dichlorobenzene.

m-Dichlorobenzene541-73-10.0366.0

U072

p-Dichlorobenzene.

p-Dichlorobenzene106-46-70.0906.0

U073

3,3'-Dichlorobenzidine.

3,3 I

-Dichlorobenzidine91-94-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U074

1,4-Dichloro-2-butene.

cis-1,4-Dichloro-2-butene1476-11-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBSTtrans-

1,4-Dichloro-2-butene764-41-0(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U075

Dichlorodifluoromethane.

Dichlorodifluoromethane75-71-80.237.2

U076

1,1-Dichloroethane.

1,1-Dichloroethane75-34-30.0596.0

U077

1,2-Dichloroethane.

---

1,2-Dichloroethane107-06-20.216.0

U078

1,1-Dichloroethylene.

1,1-Dichloroethy1ene75-35-40.0256.0

U079

1,2-Dichloroethylene.

trans-1,2-Dichloroethylene156-60-50.05430

U080

Methylene chloride.

Methylene chloride75-09-20.08930

U081

2,4-Dichlorophenol.

2,4-Dichloropheno1120-83-20.04414

U082

2,6-Dichlorophenol.

2,6-Dichloropheno187-65-00.04414

U083

1,2-Dichloropropane.

1,2-Dichloropropane78-87-50.8518

U084

1,3-Dichloropropylene.

cis-1,3-Dichloropropylene10061-01-50.03618trans-1,3-Dichloropropylene10061-02-

60.03618

U085

1,2:3,4-Diepoxybutane.

1,2:3,4-Diepoxybutanel464-53-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U086

N,N'-Diethylhydrazine.

N,N'-Diethylhydrazine1615-80-1CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED;

or CMBST

U087

0,0-Diethyl-S-methyldithiophosphate.

0,0-Diethyl-S-methyldithiophosphate3288-58-2CARBN; or CMBSTCMBST

U088

Diethyl phthalate.

---

Diethyl phthalate84-66-20.2028

U089

Diethyl stilbestrol.

Diethyl stilbestrol56-53-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U090

Dihydrosafrole.

Dihydrosafrole94-58-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U091

3,3'-Dimethoxybenzidine.

3,3'-Dimethoxybenzidine119-90-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U092

Dimethylamine.

Dimethylamine124-40-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U093

p-Dimethylaminoazobenzene.

p-Dimethylaminoazobenzene60-11-70.13CMBST

U094

7,12-Dimethylbenz(a)anthracene.

7,12-Dimethylbenz(a)anthracene57-97-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U095

3,3'-Dimethylbenzidine.

3,3'-Dimethylbenzidine119-93-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U096

, -Dimethyl benzyl hydroperoxide.

, -Dimethyl benzyl hydroperoxide80-15-9CHOXD; CHRED; CARBN; BIODG; or

CMBSTCHOXD; CHRED; or CMBST

U097

Dimethylcarbamoyl chloride.

Dimethylcarbamoyl chloride79-44-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U098

1,1-Dimethylhydrazine.

1,1-Dimethylhydrazine57-14-7CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or

CMBST

U099

1,2-Dimethylhydrazine.

---

1,2-Dimethylhydrazine540-73-8CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED;

or CMBST

U101

2,4-Dimethylphenol.

2,4-Dimethylpheno1105-67-90.03614

U102

Dimethyl phthalate.

Dimethyl phthalate131-11-30.04728

U103

Dimethyl sulfate.

Dimethyl sulfate77-78-1CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or

CMBST

U105

2,4-Dinitrotoluene.

2,4-Dinitrotoluene121-14-20.32140

U106

2,6-Dinitrotoluene.

2,6-Dinitrotoluene606-20-20.5528

U107

Di-n-octyl phthalate.

Di-n-octyl phthalate117-84-00.01728

U108

1,4-Dioxane.

1,4-Dioxane123-91-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST1,4-Dioxane;

alternate6 standard for nonwastewaters only123-91-112.0170

U109

1,2-Diphenylhydrazine.

1,2-Diphenylhydrazine122-66-7CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED;

or CMBST1,2-Diphenylhydrazine; alternate6 standard for wastewaters only122-66-

70.087NA

U110

Dipropylamine.

Dipropylaminei42-84-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U111

Di-n-propylnitrosamine.

Di-n-propylnitrosamine621-64-70.4014

U112

---

Ethyl acetate.

Ethyl acetate141-78-60.3433

U113

Ethyl acrylate.

Ethyl acrylate140-88-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U114

Ethylenebisdithiocarbamic acid salts and esters.

Ethylenebisdithiocarbamic acidlll-54-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U115

Ethylene oxide.

Ethylene oxide75-21-8(WETOX or CHOXD) fb CARBN; or CMBSTCHOXD; or CMBSTEthylene

oxide; alternate6 standard for wastewaters only75-21-80.12NA

U116

Ethylene thiourea.

Ethylene thiourea96-45-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U117

Ethyl ether.

Ethyl ether60-29-70.12160

U118

Ethyl methacrylate.

Ethyl methacrylate97-63-20.14160

U119

Ethyl methane sulfonate.

Ethyl methane sulfonate62-50-0(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U120

Fluoranthene.

Fluoranthene206-44-00.0683.4

U121

Trichloromonofluoromethane.

Trichloromonofluoromethane75-69-40.02030

U122

Formaldehyde.

Formaldehyde50-00-0(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U123

---

Formic acid.

Formic acid64-18-6(WETCX or CHOXD) fb CARBN; or CMBSTCMBST

U124

Furan.

Furan110-00-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U125

Furfural.

Furfura198-01-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U126

Glycidylaldehyde.

Glycidylaldehyde765-34-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U127

Hexachlorobenzene.

Hexachlorobenzene118-74-10.05510

U128

Hexachlorobutadiene.

Hexachlorobutadiene87-68-30.0555.6

U129

Lindane.

-BHC319-84-60.000140.066-BHC319-85-70.000140.066-BHC319-86-80.0230.066?-BHC

(Lindane)58-89-90.00170.066

U130

Hexachlorocyclopentadiene.

Hexachlorocyclopentadiene77-47-40.0572.4

U131

Hexachloroethane.

Hexachloroethane67-72-10.05530

U132

Hexachlorophene.

Hexachlorophene70-30-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U133

Hydrazine.

Hydrazine302-01-2CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD; CHRED; or CMBST

U134

Hydrogen fluoride.

---

Fluoride (measured in wastewaters only)16964?

48 87664-39 335a

35ADGAS fb NEUTR; or NEUTR

U135

Hydrogen sulfide.

Hydrogen sulfide7783-06-4CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

U136

Cacodylic acid.

Arsenic7440-38-21.45.0 mg/1 TCLP

U137

C C

1-ndeneIndenol(1,2,3-cd)pyrene.

3-ndeneIndenol(1,2,3 c,do_d)pyrene

Indcno(1,2,3 c,d)pyrcnc193-39-50.00553.4

U138

Iodomethane.

Iodomethane74-88-40.1965

U140

Isobutyl alcohol.

Isobutyl alcohol78-83-15.6170

U141

Isosafrole.

Isosafrole120-58-10.0812.6

U142

Kepone.

Kepone143-50-80.00110.13

U143

Lasiocarpine.

Lasiocarpine303-34-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U144

Lead acetate.

Lead7439-92-10.690.75 mg/1 TCLP

U145

Lead phosphate.

Lead7439-92-10.690.75 mg/1 TCLP

U146

---

Lead subacetate.

Lead7439-92-10.690.75 mg/1 TCLP

U147

Maleic anhydride.

Maleic anhydride108-31-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U148

Maleic hydrazide.

Maleic hydrazide123-33-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U149

Malononitrile.

Malononitrile109-77-3(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U150

Melphalan.

Melphalanl48-82-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U151

U151 (mercury) nonwastewaters that contain greater than or equal to 260 mg/kg

total mercury.

Mercury7439-97-6NARMERC

U151

U151 (mercury) nonwastewaters that contain less than 260 mg/kg total mercury and

that are residues from RMERC only.

Mercury7439-97-6NA0.20 mg/1 TCLP

U151

U151 (mercury) nonwastewaters that contain less than 260 mg/kg total mercury and

that are not residues from RMERC only.

Mercury7439-97-6NA0.025 mg/1 TCLP

U151

All U151 (mercury) wastewater.

Mercury7439-97-60.15NA

U151

Elemental Mercury Contaminated with Radioactive Materials.

Mercury7439-97-6NAAMLGM

U152

Methacrylonitrile.

Methacrylonitrile126-98-70.2484

---

U153

Methanethiol.

Methanethio174-93-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U154

Methanol.

Methano167-56-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBSTMethanol; alternate6 set

of standards for both wastewaters and nonwastewaters67-56-15.60.75 mg/1 TCLP

U155

Methapyrilene.

Methapyrilene91-80-50.0811.5

U156

Methyl chlorocarbonate.

Methyl chlorocarbonate79-22-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U157

3-Methylcholanthrene.

3-Methylcholanthrene56-49-50.005515

U158

4,4'-Methylene bis(2-chloroaniline).

4,4'-Methylene bis(2-chloroaniline)101-14-40.5030

U159

Methyl ethyl ketone.

Methyl ethyl ketone78-93-30.2836

U160

Methyl ethyl ketone peroxide.

Methyl ethyl ketone peroxide1338-23-4CHOXD; CHRED; CARBN; BIODG; or CMBSTCHOXD;

CHRED; or CMBST

U161

Methyl isobutyl ketone.

Methyl isobutyl ketone108-10-10.1433

U162

Methyl methacrylate.

Methyl methacrylate80-62-60.14160

U163

N-Methyl-N'-nitro-N-nitrosoguanidine.

---

N-Methyl-N'-nitro-N-nitrosoguanidine70-25-7(WETOX or CHOXD) fb CARBN; or

CMBSTCMBST

U164

Methylthiouracil.

Methylthiouraci156-04-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U165

Naphthalene.

Naphthalene91-20-30.0595.6

U166

1,4-Naphthoquinone.

1,4-Naphthoquinone130-15-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U167

1-Naphthylamine.

1-Naphthylamine134-32-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U168

2-Naphthylamine.

2-Naphthylamine91-59-80.52CMBST

U169

Nitrobenzene.

Nitrobenzene98-95-30.06814

U170

p-Nitrophenol.

p-Nitropheno1100-02-70.1229

U171

2-Nitropropane.

2-Nitropropane79-46-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U172

N-Nitrosodi-n-butylamine.

N-Nitrosodi-n-butylamine924-16-30.4017

U173

N-Nitrosodiethanolamine.

N-Nitrosodiethanolamine1116-54-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U174

N-Nitrosodiethylamine.

N-Nitrosodiethylamine55-18-50.4028

---

U176

N-Nitroso-N-ethylurea.

N-Nitroso-N-ethylurea759-73-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U177

N-Nitroso-N-methylurea.

N-Nitroso-N-methylurea684-93-5(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U178

N-Nitroso-N-methylurethane.

N-Nitroso-N-methylurethane615-53-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U179

N-Nitrosopiperidine.

N-Nitrosopiperidine100-75-40.01335

U180

N-Nitrosopyrrolidine.

N-Nitrosopyrrolidine930-55-20.01335

U181

5-Nitro-o-toluidine.

5-Nitro-o-toluidine99-55-80.3228

U182

Paraldehyde.

Paraldehydel23-63-7(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U183

Pentachlorobenzene.

Pentachlorobenzene608-93-50.05510

U184

Pentachloroethane.

Pentachloroethane76-01-7(WETOX or CHOXD) fb CARBN; or

CMBSTCMBSTPentachloroethane; alternate6 standards for both wastewaters and

nonwastewaters76-01-70.0556.0

U185

Pentachloronitrobenzene.

Pentachloronitrobenzene82-68-80.0554.8

U186

1,3-Pentadiene.

1,3-Pentadiene504-60-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

---

U187

Phenacetin.

Phenacetin62-44-20.08116

U188

Phenol.

Pheno1108-95-20.0396.2

U189

Phosphorus sulfide.

Phosphorus sulfide1314-80-3CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

U190

Phthalic anhydride.

Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)100-21-

00.05528Phthalic anhydride (measured as Phthalic acid or Terephthalic acid)85-

44-90.05528

U191

2-Picoline.

2-Picoline109-06-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U192

Pronamide.

Pronamide23950-58-50.0931.5

U193

1,3-Propane sultone.

1,3-Propane sultone1120-71-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U194

n-Propylamine.

n-Propylamine107-10-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U196

Pyridine.

Pyridine110-86-10.01416

U197

p-Benzoquinone.

p-Benzoquinone

106-51-4(WETOX or CHOXD) fb CAREN; or CMBSTCMBST

U200

Reserpine.

---

Reserpine50-55-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U201

Resorcinol

Resorcino1.108-46-3(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U202

Saccharin and salts.

Saccharin81-07-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U203

Safrole.

Safrole94-59-70.08122

U204

Selenium dioxide.

Selenium7782-49-20.825.7 mg/1 TCLP

U205

Selenium sulfide.

Selenium7782-49-20.825.7 mg/1 TCLP

U206

Streptozotocin.

Streptozotocin18883-66-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U207

1,2,4,5-Tetrachlorobenzene.

1,2,4,5-Tetrachlorobenzene95-94-30.05514

U208

1,1,1,2-

Tetrachloroethane.

1,1,1,2-Tetrachloroethane630-20-60.0576.0

U209

1,1,2,2-Tetrachloroethane.

1,1,2,2-Tetrachloroethane79-34-50.0576.0

U210

Tetrachloroethylene.

Tetrachloroethylene127-18-40.0566.0

U211

Carbon tetrachloride.

Carbon tetrachloride56-23-50.0576.0

U213

---

Tetrahydrofuran.

Tetrahydrofuran109-99-9(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U214

Thallium (I) acetate.

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

U215

Thallium (I) carbonate.

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

U216

Thallium (I) chloride.

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

U217

Thallium (I) nitrate.

Thallium (measured in wastewaters only)7440-28-01.4RTHRM; or STABL

U218

Thioacetamide.

Thioacetamide62-55-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U219

Thiourea.

Thiourea62-56-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U220

Toluene.

Toluene108-88-30.08010

U221

Toluenediamine.

Toluenediamine25376-45-8CARBN; or CMBSTCMBST

U222

o-Toluidine hydrochloride.

o-Toluidine hydrochloride636-21-5(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U223

Toluene diisocyanate.

Toluene diisocyanate26471-62-5CARBN; or CMBSTCMBST

U225

Bromoform (Tribromomethane).

---

Bromoform (Tribromomethane)75-25-20.6315

U226

1,1,1-Trichloroethane.

1,1,1-Trichloroethane71-55-60.0546.0

U227

1,1,2-Trichloroethane.

1,1,2-Trichloroethane79-00-50.0546.0

U228

Trichloroethylene.

Trichloroethylene79-01-60.0546.0

U234

1,3,5-Trinitrobenzene.

1,3,5-Trinitrobenzene99-35-4(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U235

tris-(2,3-Dibromopropy1)-phosphate.

tris-(2,3-Dibromopropyl)-phosphatel26-72-70.110.10

U236

Trypan Blue.

Trypan Blue72-57-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U237

Uracil mustard.

Uracil mustard66-75-1(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U238

Urethane (Ethyl carbamate).

Urethane (Ethyl carbamate)51-79-6(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U239

Xylenes.

Xylenes-mixed isomers

(sum of o-, m-, and p-xylene concentrations)1330-20-70.3230

U240

2,4-D (2,4-Dichlorophenoxyacetic acid).

2,4-D (2,4-Dichlorophenoxyacetic acid)94-75-70.72102,4-D (2,4-

Dichlorophenoxyacetic acid) salts and estersNA(WETOX or CHOXD) fb CARBN; or

CMBSTCMBST

U243

Hexachloropropylene.

---

Hexachloropropylene1888-71-70.03530

U244

Thiram.

Thiram137-26-8(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U246

Cyanogen bromide.

Cyanogen bromide506-68-3CHOXD; WETOX; or CMBSTCHOXD; WETOX; or CMBST

U247

Methoxychlor.

Methoxychlor72-43-50.250.18

U248

Warfarin, & salts, when present at concentrations of 0.3 percent or less.

Warfarin81-81-2(WETOX or CHOXD) fb CARBN; or CMBSTCMBST

U249

Zinc phosphide, Zn3P2, when present at concentrations of 10 percent or less.

Zinc Phosphide1314-84-7CHOXD; CHRED; or CMBSTCHOXD; CHRED; or CMBST

U271

Benomyl.

Benomy117804-35-20.0561.4

U278

Bendiocarb.

Bendiocarb22781-23-30.0561.4

U279

Carbaryl.

Carbaryl63-25-20.0060.14

U280

Barban.

Barban101-27-90.0561.4

U328

o-Toluidine.

o-Toluidine95-53-4CMBST; or CHOXD fb (BIODG or CARBN); or BIODG fb CARBNCMBST

U353

p-Toluidine.

p-Toluidine106-49-0CMBST; or CHOXD fb (BIODG or CARBN); or BIODG fb CARBNCMBST

U3S9

---

2-Ethoxyethanol.

2-Ethoxyethano1110-80-5CMBST; or CHOXD fb (BIODG or CAREN); or BIODG fb

CARBNCMBST

U364

Bendiocarb pheno1.10

Bendiocarb pheno122961-82-60.0561.4

U367

Carbofuran phenol.

Carbofuran phenol

1563-38-80.0561.4

U372

Carbendazim.

Carbendazim10605-21-70.0561.4

U373

Propham.

Propham122-42-90.0561.4

U387

Prosulfocarb.

Prosulfocarb52888-80-90.0421.4

U389

Triallate.

Triallate2303-17-50.0421.4

U394

A2213.10

A221330558-43-10.0421.4

U395

Diethylene glycol, dicarbamate.10

Diethylene glycol, dicarbamate5952-26-10.0561.4

U404

Triethylamine.

Triethylamine101-44-80.0811.5

U409

Thiophanate-methyl.

Thiophanate-methyl23564-05-80.0561.4

U410

---

Thiodicarb.

Thiodicarb59669-26-00.0191.4

U411

Propoxur.

Propoxur114-26-10.0561.4

Notes:

1?

The waste descriptions provided in this table do not replace waste

descriptions in 35 Ill. Adm. Code 721. Descriptions of Treatment or Regulatory

Subcategories are provided, as needed, to distinguish between applicability of

different standards.

2?

CAS means Chemical Abstract Services. When the waste code or regulated

constituents are described as a combination of a chemical with its salts or

esters, the CAS number is given for the parent compound only.

3?

Concentration standards for wastewaters are expressed in mg/1 and are

based on analysis of composite samples.

4?

All treatment standards expressed as a Technology Code or combination of

Technology Codes are explained in detail in Table C of this Part, "Technology

Codes and Descriptions of Technology-Based Standards." "fb" inserted between

waste codes denotes "followed by," so that the first-listed treatment is

followed by the second-listed treatment. A semicolon (;) separates alternative

treatment schemes.

5

?

Except for Metals (EP or TCLP) and Cyanides (Total and Amenable), the

nonwastewater treatment standards expressed as a concentration were established,

in part, based on incineration in units operated in accordance with the

technical requirements of Subpart 0 of 35 Ill. Adm. Code 724 or Subpart 0 of 35

Ill. Adm. Code 725 or based on combustion in fuel substitution units operating

in accordance with applicable technical requirements. A facility may comply

with these treatment standards according to provisions in Section 728.140(d).

All concentration standards for nonwastewaters are based on analysis of grab

samples.

6

?

Where an alternate treatment standard or set of alternate standards has

been indicated, a facility may comply with this alternate standard, but only for

the Treatment or Regulatory Subcategory or physical form (i.e., wastewater or

nonwastewater) specified for that alternate standard.

7?

Both Cyanides (Total) and Cyanides (Amenable) for nonwastewaters are to be

analyzed using Method 9010C or 9012B, in "Test Methods for Evaluating Solid

Waste, Physical or Chemical Methods," USEPA publication number EPA-530/SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a), with a sample size of

10 grams and a distillation time of one hour and 15 minutes.

8?

These wastes, when rendered non-hazardous and then subsequently managed in

CWA or CWA-equivalent systems, are not subject to treatment standards. (See

Section 728.101(c)(3) and (c)(4).)

9?

These wastes, when rendered non-hazardous and then subsequently injected

in a Class I SDWA well, are not subject to treatment standards. (See 35 Ill.

Adm. Code 738.101(d).)

---

10?

The treatment standard for this waste may be satisfied by either meeting

the constituent concentrations in the table in this Section or by treating the

waste by the specified technologies: combustion, as defined by the technology

code CMBST at Table C, for nonwastewaters; and biodegradation, as defined by the

technology code BIODG; carbon adsorption, as defined by the technology code

CARBN; chemical oxidation, as defined by the technology code CHOXD; or

combustion, as defined as technology code CMBST, at Table C, for wastewaters.

11?

For these wastes, the definition of CMBST is limited to any of the

following that have obtained a determination of equivalent treatment under

Section 728.142(b): (1) combustion units operating under 35 Ill. Adm. Code 726,

(2) combustion units permitted under Subpart 0 of 35 Ill. Adm. Code 724, or (3)

combustion units operating under Subpart 0 of 35 Ill. Adm. Code 725.

12?

Disposal of USEPA hazardous waste number K175 waste that has complied with

all applicable Section 728.140 treatment standards must also be

macroencapsulated in accordance with Table F of this Part, unless the waste is

placed in either of the following types of facilities:

a)

A RCRA Subtitle C monofill containing only K175 wastes that meet all

applicable 40 CFR 268.40 treatment standards; or

b)

A dedicated RCRA Subtitle C landfill cell in which all other wastes being

co-disposed are at pH-16.0.

BOARD NOTE: Derived from table to 40 CFR 268.40 (2005) (2007).

NA?

means not applicable.

(Source: Amended at 32 Ill. Reg. ?

--, effective ?

)

Section 728.Tab1oTABLE U ? Universal Treatment Standards (UTS)

Regulated Constituent-Common NameCAS1 No.Wastewater Standard Concentration2 (in

mg/12 )Nonwastewater Standard Concentration3 (in mg/kg;- unless noted as "mg/1

TCLP")Acenaphthylene208-96-80.0593.4Acenaphthene83-32-90.0593.4Acetone67-64-

10.28160Acetonitrile75-05-85.638Acetophenone96-86-20.0109.72-

Acetylaminofluorene53-96-30.059140Acrolein107-02-80.29NAAcrylamide79-06-

11923Acrylonitrile107-13-10.2484Aldicarb sulfone61646-88-40.0560.28Aldrin309-00-

20.0210.0664-Aminobipheny192-67-10.13NAAniline62-53-30.8114o-Anisidine (2-

methoxyaniline)90-04-00.0100.66Anthracene120-12-70.0593.4Aramite140-57-80.36NA-

BHC319-84-60.000140.066-BHC319-85-70.000140.066-BHC319-86-80.0230.066?-BHC58-89-

90.00170.066Barban6101-27-90.0561.4Bendiocarb622781-23-30.0561.4Benomy1617804-

35-20.0561.4Benz(a)anthracene56-55-30.0593.4Benzal chloride98-87-

30.0556.0Benzene71-43-20.1410Benzo(b)fluoranthene (difficult to distinguish from

benzo(k)fluoranthene)205-99-20.116.8Benzo(k)fluoranthene (difficult to

distinguish from benzo(b)fluoranthene)207-08-90.116.8Benzo(g,h,i)perylene191-24-

20.00551.8Benzo(a)pyrene50-32-80.0613.4Bromodichloromethane75-27-40.3515Methyl

bromide (Bromomethane)74-83-90.11154-Bromophenyl phenyl ether101-55-30.05515n-

Butyl alcohol71-36-35.62.6Butylate62008-41-50.0421.4Butyl benzyl phthalate85-68-

70.017282-sec-Buty1-4,6-dinitrophenol (Dinoseb)88-85-70.0662.5Carbary1663-25-

20.0060.14Carbenzadim610605-21-70.0561.4Carbofuran61563-66-20.0060.14Carbofuran

pheno161563-38-80.0561.4Carbon disulfide75-15-03.84.8 mg/1 TCLPCarbon

tetrachloride56-23-50.0576.0Carbosulfan655285-14-80.0281.4Chlordane (? and ?

isomers)57-74-90.00330.26p-Chloroaniline106-47-80.4616Chlorobenzene108-90-

70.0576.0Chlorobenzilate510-15-60.10NA2-Chloro-1,3-butadiene126-99-80.0570.28p-

---

Chloro-m-creso159-50-70.01814Chlorodibromomethane124-48-10.05715Chloroethane75-

00-30.276.0bis(2-Chloroethoxy)methane111-91-10.0367.2bis(2-Chloroethyl)ether111-

44-40.0336.02-Chloroethyl vinyl ether110-75-80.062NAChloroform67-66-

30.0466.0bis(2-Chloroisopropyl)ether39638-32-90.0557.2Chloromethane (Methyl

chloride)74-87-30.19302-Chloronaphthalene91-58-70.0555.62-Chloropheno195-57-

80.0445.73-Chloropropylene107-05-10.03630Chrysene218-01-90.0593.4p-Cresidine120-

71-80.0100.66o-Creso195-48-70.115.6m-Cresol (difficult to distinguish from p-

cresol)108-39-40.775.6p-Cresol (difficult to distinguish from m-cresol)106-44-

50.775.6m-Cumenyl methylcarbamate664-00-60.0561.4Cyclohexanone108-94-10.360.75

mg/1 TCLPo,p'-DDD53-19-00.0230.087p,p'-DDD72-54-80.0230.087o,p'-DDE3424-82-

60.0310.087p,pl-DDE72-55-90.0310.087o,p'-DDT789-02-60.00390.087p,p1-DDT50-29-

30.00390.087Dibenz(a,h)anthracene53-70-30.0558.2Dibenz(a,e)pyrene192-65-

40.061NA1,2-Dibromo-3-chloropropane96-12-80.11151,2-Dibromoethane/Ethylene

dibromide106-93-40.02815Dibromomethane74-95-30.1115m-Dichlorobenzene541-73-

10.0366.0o-Dichlorobenzene95-50-10.0886.0p-Dichlorobenzene106-46-

70.0906.0Dichlorodifluoromethane75-71-80.237.21,1-Dichloroethane75-34-

30.0596.01,2-Dichloroethane107-06-20.216.01,1-Dichloroethylene75-35-

40.0256.0trans-1,2-Dichloroethylene156-60-50.054302,4-Dichloropheno1120-83-

20.044142,6-Dichloropheno187-65-00.044142,4-Dichlorophenoxyacetic acid/2,4-D94-

75-70.72101,2-Dichloropropane78-87-50.8518cis-1,3-Dichloropropylene10061-01-

50.03618trans-1,3-Dichloropropylene10061-02-60.03618Dieldrin60-57-

10.0170.13Diethyl phthalate84-66-20.2028p-Dimethylaminoazobenzene60-11-

70.13NA2,4-Dimethylaniline (2,4-xylidine)95-68-10.0100.662,4-Dimethyl pheno1105-

67-90.03614Dimethyl phthalate131-11-30.04728Di-n-butyl phthalate84-74-

20.057281,4-Dinitrobenzene100-25-40.322.34,6-Dinitro-o-creso1534-52-10.281602,4-

Dinitropheno151-28-50.121602,4-Dinitrotoluene121-14-20.321402,6-

Dinitrotoluene606-20-20.5528Di-n-octyl phthalate117-84-00.01728Di-n-

propylnitrosamine621-64-70.40141,4-Dioxane123-91-112.0170Diphenylamine

(difficult to distinguish from diphenylnitrosamine)122-39-

40.9213Diphenylnitrosamine (difficult to distinguish from diphenylamine)86-30-

60.92131,2-Diphenylhydrazine122-66-70.087NADisulfoton298-04-

40.0176.2Dithiocarbamates (total)6137-30-40.02828Endosulfan 1959-98-

80.0230.066Endosulfan I133213-65-90.0290.13Endosulfan sulfate1031-07-

80.0290.13Endrin72-20-80.00280.13Endrin aldehyde7421-93-40.0250.13EPTC6759-94-

40.0421.4Ethyl acetate141-78-60.3433Ethyl benzene100-41-40.05710Ethyl cyanide

(Propanenitrile)107-12-00.24360Ethylene oxide75-21-80.12NAEthyl ether60-29-

70.12160bis(2-Ethylhexyl) phthalate117-81-70.2828Ethyl methacrylate97-63-

20.14160Famphur52-85-70.01715Fluoranthene206=44-00.0683.4Fluorene86-73-

70.0593.4Formetanate hydrochloride623422-53-90.0561.4Heptachlor76-44-

80.00120.0661,2,3,4,6,7,8-Heptachlorodibenzo-p-dioxin (1,2,3,4,6,7,8-

HpCDD)35822-46-90.0000350.00251,2,3,4,6,7,8-Heptachlorodibenzofuran

(1,2,3,4,6,7,8-HpCDF)67562-39-40.0000350.00251,2,3,4,7,8,9-

Heptachlorodibenzofuran (1,2,3,4,7,8,9-HpCDF)55673-89-70.0000350.0025Heptachlor

epoxide1024-57-30.0160.066Hexachlorobenzene118-74-10.05510Hexachlorobutadiene87-

68-30.0555.6Hexachlorocyclopentadiene77-47-40.0572.4HxCDDs (All

Hexachlorodibenzo-p-dioxins)NA0.0000630.001HxCDFs (All

Hexachlorodibenzofurans)55684-94-10.0000630.001Hexachloroethane67-72-

10.05530Hexachloropropylene1888-71-70.03530Indeno (1,2,3-c,d) pyrene193-39-

50.00553.41odomethane74-88-40.19651sobutyl alcohol78-83-15.61701sodrin465-73-

60.0210.0661sosafrole120-58-10.0812.6Kepone143-50-

00.00110.13Methacrylonitrile126-98-70.2484Methano167-56-15.60.75 mg/1

TCLPMethapyrilene91-80-50.0811.5Methiocarb62032-65-70.0561.4Methomy1616752-77-

50.0280.14Methoxychlor72-43-50.250.183-Methylcholanthrene56-49-50.0055154,4-

Methylene bis(2-chloroaniline)101-14-40.5030Methylene chloride75-09-

20.08930Methyl ethyl ketone78-93-30.2836Methyl isobutyl ketone108-10-

10.1433Methyl methacrylate80-62-60.14160Methyl methansulfonate66-27-

30.018NAMethyl parathion298-00-00.0144.6Metolcarb61129-41-

---

50.0561.4Mexacarbate6315-18-40.0561.4Molinate62212-67-10.0421.4Naphthalene91-20-

30.0595.62-Naphthylamine91-59-80.52NAo-Nitroaniline88-74-40.2714p-

Nitroaniline100-01-60.02828Nitrobenzene98-95-30.068145-Nitro-o-toluidine99-55-

80.3228o-Nitropheno188-75-50.02813p-Nitropheno1100-02-70.1229N-

Nitrosodiethylamine55-18-50.4028N-Nitrosodimethylamine62-75-90.402.3N-Nitroso-

di-n-butylamine924-16-30.4017N-Nitrosomethylethylamine10595-95-60.402.3N-

Nitrosomorpholine59-89-20.402.3N-Nitrosopiperidine100-75-40.01335N-

Nitrosopyrrolidine930-55-20.013351,2,3,4,6,7,8,9-Octachlorodibenzo-p-dioxin

(1,2,3,4,6,7,8,9-0CDD)3268-87-90.0000630.0051,2,3,4,6,7,8,9-

Octachlorodibenzofuran (1,2,3,4,6,7,8,9-0CDF)39001-02-

00.0000630.0050xamy1623135-22-00.0560.28Parathion56-38-20.0144.6Total PCBs (sum

of all PCB isomers, or all Aroclors)81336-36-30.1010Pebulate61114-71-

20.0421.4Pentachlorobenzene608-93-50.05510PeCDDs (All Pentachlorodibenzo-p-

dioxins)36088-22-90.0000630.001PeCDFs (All Pentachlorodibenzofurans)30402-15-

40.0000350.001Pentachloroethane76-01-70.0556.0Pentachloronitrobenzene82-68-

80.0554.8Pentachloropheno187-86-50.0897.4Phenacetin62-44-20.08116Phenanthrene85-

01-80.0595.6Pheno1108-95-20.0396.21,3-Phenylenediamine108-45-

20.0100.66Phorate298-02-20.0214.6Phthalic acid100-21-00.05528Phthalic

anhydride85-44-90.05528Physostigmine657-47-60.0561.4Physostigmine salicylate657-

64-70.0561.4Promecarb62631-37-00.0561.4Pronamide23950-58-50.0931.5Propham6122-

42-90.0561.4Propoxur6114-26-10.0561.4Prosulfocarb652888-80-90.0421.4Pyrene129-

00-00.0678.2Pyridine110-86-10.01416Safrole94-59-70.08122Silvex (2,4,5-TP)93-72-

10.727.91,2,4,5-Tetrachlorobenzene95-94-30.05514TCDDs (All Tetrachlorodibenzo-p-

dioxins)41903-57-50.0000630.001TCDFs (All Tetrachlorodibenzofurans)55722-27-

50.0000630.0011,1,1,2-Tetrachloroethane630-20-60.0576.01,1,2,2-

Tetrachloroethane79-34-50.0576.0Tetrachloroethylene127-18-40.0566.02,3,4,6-

Tetrachloropheno158-90-20.0307.4Thiodicarb659669-26-00.0191.4Thiophanate-

methy1623564-05-80.0561.4Toluene108-88-30.08010Toxaphene8001-35-

20.00952.6Triallate62303-17-50.0421.4Tribromomethane (Bromoform)75-25-

20.63151,2,4-Trichlorobenzene120-82-10.055191,1,1-Trichloroethane71-55-

60.0546.01,1,2-Trichloroethane79-00-50.0546.0Trichloroethylene79-01-

60.0546.0Trichloromonofluoromethane75-69-40.020302,4,5-Trichloropheno195-95-

40.187.42,4,6-Trichloropheno188-06-20.0357.42,4,5-Trichlorophenoxyacetic

acid/2,4,5-T93-76-50.727.91,2,3-Trichloropropane96-18-40.85301,1,2-Trichloro-

1,2,2-trifluoroethane76-13-10.05730Triethylamine6101-44-80.0811.5tris-(2,3-

Dibromopropyl) phosphate126-72-70.110.10Vernolate61929-77-70.0421.4Vinyl

chloride75-01-40.276.0Xylenes-mixed isomers (sum of o-, m-, and p-xylene

concentrations)1330-20-70.3230Antimony7440-36-01.91.15 mg/1 TCLPArsenic7440-38-

21.45.0 mg/1 TCLPBarium7440-39-31.221 mg/1 TCLPBeryllium7440-41-70.821.22 mg/1

TCLPCadmium7440-43-90.690.11 mg/1 TCLPChromium (Total)7440-47-32.770.60 mg/1

TCLPCyanides (Total)457-12-51.2590Cyanides (Amenable)457-12-

50.8630Fluoride516984-48-835NALead7439-92-10.690.75 mg/1 TCLPMercury-

Nonwastewater from Retort7439-97-6NA0.20 mg/1 TCLPMercury-All Others7439-97-

60.150.025 mg/1 TCLPNicke17440-02-03.9811 mg/1 TCLPSelenium77782-49-20.825.7

mg/1 TCLPSilver7440-22-40.430.14 mg/1 TCLPSulfide18496-25-814NAThallium7440-28-

01.40.20 mg/1 TCLPVanadium57440-62-24.31.6 mg/1 TCLPZinc57440-66-62.614.3 mg/1

TCLP

1?

CAS means Chemical Abstract Services. When the waste code or regulated

constituents are described as a combination of a chemical with its salts or

esters, the CAS number is given for the parent compound only.

2?

Concentration standards for wastewaters are expressed in mg/1 are based on

analysis of composite samples.

3?

Except for metals (EP or TCLP) and cyanides (total and amenable), the

nonwastewater treatment standards expressed as a concentration were established,

in part, based on incineration in units operated in accordance with the

4

---

technical requirements of Subpart 0 of 35 Ill. Adm. Code 724 or Subpart 0 of 35

M. Adm. Code 725 or on combustion in fuel substitution units operating in

accordance with applicable technical requirements. A facility may comply with

these treatment standards according to provisions in Section 728.140(d). All

concentration standards for nonwastewaters are based on analysis of grab

samples.

4?

Both Cyanides (Total) and Cyanides (Amenable) for nonwastewaters are to be

analyzed using Method 9010C or 9012B, in "Test Methods for Evaluating Solid

Waste, Physical/Chemical Methods," USEPA publication number EPA-530/ SW-846,

incorporated by reference in 35 Ill. Adm. Code 720.111(a), with a sample size of

10 grams and a distillation time of one hour and 15 minutes.

5

?

These constituents are not "underlying hazardous constituents" in

characteristic wastes, according to the definition at Section 728.102(i).

6?

This footnote corresponds with footnote 6 to the table to 40 CFR

268.48(a), which has already expired by its own terms. This statement maintains

structural consistency with the corresponding federal regulations.

7?

This constituent is not an underlying hazardous constituent, as defined at

Section 728.102(i), because its UTS level is greater than its TC level. Thus, a

treated selenium waste would always be characteristically hazardoahazardous

unless it is treated to below its characteristic level.

8

?

This standard is temporarily deferred for soil exhibiting a hazardous

characteristic due to USEPA hazardous waste numbers D004 through D011 only.

Note: NA means not applicable.

BOARD NOTE: Derived from table to 40 CFR 268.48(a) (2005) (2007).

(Source: Amended at 32 Ill. Reg.

ILLINOIS RECI T R

JCAR350728-0805697r01

?, effective ?

POLLUTION CONTROL BOARD

---

Insertion_

Delet-ien-

Moved from

Moved to

Style change

Format change

Moved deletion

Inserted cell

Deleted cell

Moved cell

Split/Merged cell

Padding cell

Document comparison done by DeltaView on Thursday, April 03, 2008 3:00:07 PM

Input:

Document 1

file://11Input/35-728-agencydisk(issue150.doc

Document 2

file://11Input/35-728-JCARr01(issue15).doc

Rendering set

Standard

Legend:

Statistics:

Count

Insertions

60

Deletions

121

Moved from

0

Moved to

0

Style change

0

Format changed

0

Total changes

181