1. 79-356
      2. 79-369
      3. 79-394
      4. 79-463
      5. 79-478
      6. 79-510
      7. 79-603
      8. 79.604
      9. —2 66—
      10. mailing lists; and
      11. (Board Note: Derived from 40 CFR 403.13(j) (1986))
      12. Section 310.721 Agency Review of FDF Requests
      13. (Board Note: Derived from 40 CFR 403.13(k) (1986))
      14. (1986).
      15. 79-673

ILLINOIS POLLUTION CONTROL BOARD
July
16,
1987
IN THE MATTER OF:
)
R86—44
PRETREATMENT REGULATIONS
)
FINAL ORDER.
ADOPTED RULE
ORDER OF THE BOARD
(by
3. Marlin):
On October
9,
1986,
the Board
opened this Docket for the
purpose of promulgating regulations establishing
a pretreatment
program pursuant to Section 13.3 of the Environmental Protection
Act (Act), as amended by P.A.
84—1320.
On March
25,
1987, the
Board proposed
amendments
for public comment.
In this Order
the
Board
is adopting amendments
to 35
Ill.
Adm.
Code
307 and 309,
and
a new 35
Ill. Adm. Code 310.
Section 13.3 of the Act requires the Board
to adopt
regulations which are “identical
in
substance” with federal
regulations promulgated by the United States Environmental
Protection Agency (USEPA)
to implement the pretreatment
requirements of
Sections 307 and 402 of the
Clean Water
Act
(CWA),
which was previously known as the Federal Water
Pollution
Control Act.
Section 13.3 creates
an abbreviated procedure
similar
to that provided by Sections 13(c)
and 22.4(a)
of the Act
for the UIC and RCRA programs.
Title VII of the Act and Sections
5 and 6.02 of the Administrative Procedure Act
(APA)
do not apply
to “identical
in
substance”
regulations adopted
to establish the
pretreatment program.
However, the Board
is required to provide
for
notice
and
public
comment
before
rules
are
filed
with
the
Secretary
of
State.
Because
Section
5
of
the
APA
does
not
apply,
the
proposed
rules
will
not
be
subject
to
second notice review by
the
Joint
Committee
on Administrative Rules
(JCAR).
The
Department
of
Energy
and
Natural
Resources
(DENR)
is allowed
to
conduct
an
economic
impact
study
(EcIS)
on
the
rules,
but
the
study
and
hearings
are
not
required
before
the
rules
are
filed.
On this same day the Board has adopted
an Opinion
supporting
this action.
The Board will delay
filing of the rules
until
after August
5,
1987,
to allow for motions
to reconsider by the
agencies
involved
in the authorization process.
The complete
text of the adopted amendments
is as
follows:
79.347

—2—
TITLE
35:
ENVIRONMENTAL PROTECTION
SUBTITLE
C:
WATER POLLUTION
CHAPTER
I:
POLLUTION CONTROL BOARD
PART 307
SEWER DISCHARGE CRITERIA
SUBPART A:
GENERAL PROVISIONS
Section
307.101
307.102
307.103
307.104
307.105
307
.~e3dooi
307.1002
307.1003
307.1005
307.1007
Preamble
(Renumbered)
General Requirements
(Renumbered)
Mercury (Renumbered)
Cyanide
(STORET number 00720)
(Renumbered)
Pretreatment Requirements (Repealed)
Preamble
Definitions
Test Procedures for Measurement
Toxic Pollutants
pH Limitations
under Continuous Monitoring
SUBPART B:
GENERAL AND SPECIFIC PRETREATMENT REQUIREMENTS
Section
307.~9~l10lGeneral and Specific Requirements
307.~Ga1102Mercury
307.~94llO3Cyanide +SPORE~rti~e~O9~9+
SUBPART
F:
DAIRY PRODUCTS PROCESSING
Section
307.1501
307.1502
307.1503
307.1504
307 .1505
307.1506
307.1507
307.1508
307.1509
307.1510
307.1511
307.1512
Receiving Stations
Fluid Products
Cultured Products
Butter
Cottage Cheese and Cultured Cream Cheese
Natural and Processed Cheese
Fluid Mix
for Ice Cream and other
Frozen Desserts
Ice Cream,
Frozen Desserts, Novelties and Other Dairy
Desserts
Condensed Milk
Dry Milk
Condensed
Whey
Dry Whey
SUBPART
G:
GRAIN
MILLS
Section
307.1601
307.1602
307.1603
307.1604
307.1605
307.1606
Corn Wet Milling
Corn Dry Milling
Normal Wheat
Flour Milling
Bulgur
Wheat
Flour
Milling
Normal
Rice
Milling
Parboiled
Rice
Milling
79-348

—3—
307.1607
307.1608
307.1609
307.1610
Animal Feed
Hot Cereal
Ready—to—eat Cereal
Wheat Starch
and Gluten
SUBPART
H:
CANNED AND PRESERVED FRUITS AND VEGETABLES
Section
307.1701
307.1702
307.1703
307.1704
307.1705
307.1706
307.1707
307.1708
Apple Juice
Apple Products
Citrus Products
Frozen Potato Products
Dehydrated Potato Products
Canned and Preserved Fruits
Canned and Preserved Vegetables
Canned
and Miscellaneous Specialties
SUBPART
I:
CANNED AND PRESERVED SEAFOOD
Section
307.1801
307.1815
Farm—raised Catfish
Fish Meal Processing Subcategory
SUBPART
3:
SUGAR PROCESSING
Section
307.1901
307.1902
307.1903
Beet Sugar Processing
Crystalline Cane Sugar Refining
Liquid Cane Sugar Refining
SUBPART K:
TEXTILE MILLS
Section
307.2000
307.2001
307.2002
307.2003
307.2004
307.2005
307.2006
307.2007
307.2008
307.2009
General Provisions
Wool Scouring
Wool Finishing
Low Water Use
Processing
Woven Fabric Finishing
Knit Fabric Finishing
Carpet Finishing
Stock and Yarn Finishing
Nonwoven Manufacturing
Felted Fabric Processing
SUBPART
L:
CEMENT MANUFACTURING
Section
307.2101
307. 2102
307.2103
Nonleaching
Leaching
Materials Storage Piles Runoff
Section
SUBPART
M:
FEEDLOTS
79-349

—4—
307.2201
307.2202
General
Ducks
SUBPART N:
ELECTROPLATING
Section
307.2300
307.2301
307.2302
307.2304
307.2305
307.2306
307.2307
307.2308
General Provisions
Electroplating of Common Metals
Electrqplating of Precious Metals
Anodizing
Coatings
Chemical Etching and Milling
Electroless Plating
Printed Circuit Boards
SUBPART 0:
ORGANIC CHEMICALS MANUFACTURING
Section
307.2402
Processes
with
Process
Water
Contact
only
as
Steam
Diluerit,
Quench
or
Vent
Gas
Absorbent
SUBPART
P:
INORGANIC CHEMICALS MANUFACTURING
Aluminum Chloride Production
Aluminum Sulfate Production
Calcium
Carbide
Production
Calcium Chloride Production
Calcium Oxide Production
Chlor—alkali Process
(Chlorine and Sodium
of
Potassium Hydroxide Production)
Hydrofluoric Acid Production
Hydrogen Peroxide Production
Potassium Metal Production
Potassium Dichromate Production
Potassium Sulfate Production
Sodium Bicarbonate Production
Sod
Sodi
ium Chloride Production
-
-.
Sod~umSulfite Production
Titanium Dioxide Production
Aluminum Fluoride Production
Ammonium Chloride Production
Borax Production
Boric Acid Production
Bromme Production
ium Carbonate Production
Calc
Calcium Hydroxide Production
~um Dicriromate and Sodium Sulfate Production
Section
307.2501
307.2502
307.2503
307.2504
307.2505
307.2506
307.2508
307.2509
307.2511
307.2512
307.2513
307.2514
307.2516
307.2517
307.2520
307.2522
307.2523
307.2524
307.2527
307.2528
307.2529
307.2530
307.2531
307.2533
307.2534
307.2535
307.2536
307.2538
307. 2540
Chrome Pigments Production
Carbon Monoxide and Byproduct Hydrogen Production
Chromic Acid Production
Copper Salts Production
Ferric Chloride Production
Fluorine Production
79-350

—5—
307.2541
307.2542
307.2543
307.2544
307.2545
307.2547
307.2549
307.2550
307.2551
307.2553
307.2554
307.2555
307.2560
307.2563
307.2564
307.2565
307.2566
307.2567
Section
307.2701
307.2702
307.2703
307.2704
307.2705
307.2706
307.2707
307.2708
307.2709
307.2710
307.2711
307.2712
307.2713
307.2714
307.2715
307.2716
307.2717
307.2718
307.2719
Hydrogen Production
Hydrogen Cyanide Production
Iodine Production
Lead Monoxide Production
Lithium Carbonate Production
Nickel Salts Production
Oxygen and Nitrogen Production
Potassium Chloride Production
Potassium Iodide Production
Silver Nitrate Production
Sodium Bisulfite Production
Sodium Fluoride Production
Stannic Oxide Production
Zinc Sulfate Production
Cadmium Pigments and Salts Production
Cobalt Salts Production
Sodium Chlorate Production
Zinc Chloride Production
SUBPART
R:
SOAP AND DETERGENTS
Soap Manufacturing by Batch Kettle
Fatty Acid Manufacturing by Fat Splitting
Soap Manufacturing by Fatty Acid Neutralization
Glycerine Concentration
Glycerine Distillation
Manufacture of Soap Flakes
and Powders
Manufacture of Bar
Soaps
Manufacture of Liquid Soaps
Oleum Sulfonation and Sulfation
Air—Sulfur Trioxide Sulfation and Sulfonation
Sulfur Trioxide Solvent and Vacuum Sulfonation
Sulfamic Acid Sulfation
Chlorosulfonic Acid Sulfation
Neutralization of Sulfuric Acid Esters
and Sulfonic
Acids
Manufacture of Spray Dried Detergents
Manufacture of Liquid Detergents
Manufacturing of Detergents by Dry Blending
Manufacture of Drum Dried Detergents
Manufacture of Detergent Bars and Cakes
SUBPART
5:
FERTILIZER MANUFACTURING
Section
307.2801
307.2802
307.2803
307.2804
307.2805
307.2806
307.2807
Phosphate
Ammonia
Urea
Amrnonium Nitrate
Nitric Acid
Ammoniuxn Sulfate Production
Mixed
and Blend
Fertilizer Production
79-351

—6—
SUBPART
T:
PETROLEUM REFINING
Section
307.2901
307.2902
307.2903
307.2904
307.2905
Topping
Cracking
Petrochemical
Lube
Integrated
SUBPART U:
IRON AND STEEL MANUFACTURING
Section
307.3000
307.3001
307.3002
307.3003
307.3004
307.3005
307.3006
307.3007
307.3008
307.3009
307.3010
307.3011
307.3012
General Provisions
Cokeinaking
Sintering
Ironma kIng
Steelmaking
Vacuum Degassing
Continuous Casting
Hot Forming
Salt Bath Descaling
Acid Pickling
Cold Forming
Alkaline Cleaning
Hot Coating
SUBPART V:
NONFERROUS METALS MANUFACTURING
Section
307.3100
307.3101
307.3102
307.3103
307.3104
307.3105
307.3106
307.3107
307.3108
307.3109
307.3110
307.3111
307.3112
307.3113
307.3114
307.3115
307.3116
307. 3117
307. 3118
307.3119
307.3120
307.3121
307.3122
307. 3123
307.3124
General Provisions
Bauxite Refining
Primary Aluminum Smelting
Secondary
Aluminum
Smelting
Primary
Copper
Smelting
Primary Electrolytic Copper Refining
Secondary Copper
Primary Lead
Primary Zinc
Metallurgical Acid Plants
Primary Tungsten
Primary Columbium—Tantalum
Secondary Silver
Secondary Lead
Primary Antimony
Primary Beryllium
Primary and Secondary Germanium and Gallium
Secondary Indium
Secondary Mercury
Primary Molybdenum and Rhenium
Secondary Molybdenum
and Vanadium
Primary Nickel
and Cobalt
Secondary Nickel
Primary Precious Metals
and Mercury
Secondary
Precious
Metals
79-352

—7—
307.3125
307.3126
307.3127
307.3128
307.3129
307.3130
307.3131
Primary
Rare
Earth
Metals
Secondary Tantalum
Secondary Tin
Primary and Secondary Titanium
Secondary Tungsten and Cobalt
Secondary Uranium
Primary Zirconium and Hafnium
SUBPART
X:
STEAM ELECTRIC POWER GENERATING
Section
307. 3301
Section
307.3401
307.3402
307.3403
307.3404
307.3405
307.3406
307.3407
Section
307.3500
307.3501
307.3502
307.3503
307.3504
307.3505
307.3506
307.3507
307.3508
307.3509
Steam Electric Power Generating
SUBPART
Y:
FERROALLOY MANUFACTURING
Open Electric Furnaces With Wet Air Pollution Control
Devices
Covered Electric Furnaces and Other Smelting
Operations with Wet Air Pollution Control Devices
Slag Processing
Covered Calcium Carbide Furnaces With Wet Air
Pollution Control Devices
Other Calcium Carbide Furnaces
Electrolytic Manganese Products
Electrolytic Chromium
SUBPART
Z:
LEATHER TANNING AND FINISHING
General Provisions
Hair Pulp, Chrome Tan, Retan—Wet Finish
Hair Save,
Chrome Tan, Retan—Wet Finish
Hair Save or Pulp, Non—Chrome Tan, Retan—Wet Finish
Retan—Wet Finish—Sides
No
Beamhouse
Through—the—Blue
Shearl
ing
Pigskin
Retan—Wet Finish—Splits
SUBPART BA:
GLASS MANUFACTURING
Section
307.3601
307.3602
307.3603
307.3604
307.3605
307.3606
307.3607
307.3608
307. 3610
307. 3611
Insulation Fiberglass
Sheet Glass Manufacturing
Rolled Glass Manufacturing
Plate Glass Manufacturing
Float Glass Manufacturing
Automotive Glass Tempering
Automotive Glass Laminating
Glass Container Manufacturing
Glass Tubing
(Danner) Manufacturing
Television Picture Tube Envelope Manufacturing
79-353

—8—
307.3612
307.3613
Incandescent Lamp Envelope Manufacturing
Hand Pressed and Blown Glass Manufacturing
SUBPART BB:
ASBESTOS MANUFACTURING
Section
307.3701
307.3702
307.3703
307.3704
307.3705
307.3706
307.3707
307.3708
307.3709
307.3710
307
.
3711
Asbestos—Cement Pipe
Asbestos—Cement Sheet
Asbestos Paper
(Starch Binder)
Asbestos Paper
(Elastomeric Binder)
Asbestos Miliboard
Asbestos Roofing
Asbestos Floor Tile
Coating
or Finishing of Asbestos Textiles
Solvent Recovery
Vapor Absorption
Wet Dust Collection
SUBPART BC:
RUBBER MANUFACTURING
Section
307.3801
307.3802
307.3803
307.3804
307.3805
307.3806
307.3807
307.3808
307.3809
307.3810
307.3811
Tire and Inner Tube Plants
Emulsion Crumb Rubber
Solution Crumb Rubber
Latex Rubber
Small—Sized General Molded,
Extruded,
and Fabricated
Rubber Plants
Medium—Sized General Molded, Extruded,
and Fabricated
Rubber
Plants
Large—Sized General Molded, Extruded,
and Fabricated
Rubber Plants
Wet Digestion Reclaimed Rubber
Pan, Dry Digestion,
and Mechanical Reclaimed Rubber
Latex—Dipped, Latex—Extruded,
and Latex—Molded Rubber
Latex Foam
SUBPART BD:
TIMBER PRODUCTS PROCESSING
Section
307.3900
307.3901
307.3902
307.3903
307.3904
307.3905
307.3906
307.3907
307.3908
307.3909
307.3910
307.3911
307.3912
307.3913
307.3914
General Provisions
Barking
Veneer
Plywood
Dry Process Hardboard
Wet
Process
Hardboard
Wood
Preserving—Water
Borne
or
Nonpressure
Wood Preserving—Steam
Wood Preserving—Boultori
Wet Storage
Log Washing
Sawmills and Planing Mills
Finishing
Particleboard Manufacturing
Insulation
Board
79-354

—9—
307.3915
Wood Furniture and Fixture Production Without Water
Wash Spray Booth(s)
or Without Laundry Facilities
307.3916
Wood Furniture and Fixture Production with Water Wash
Spray Booth(s)
or With Laundry Facilities
SUBPART BE:
PULP,
PAPER AND PAPERBOARD
Section
307.4000
General Provisions
307.4001
Unbleached Kraft
307.4002
Semi—Chemical
307.4004
Unbleached Kraft—Neutral Sulfite Semi—Chemical
(Cross
Recovery)
307.4005
Paperboard From Wastepaper
307.4006
Dissolving Kraft
307.4007
Market Bleached Kraft
307.4008
BCT Bleached Kraft
307.4009
Fine Bleached Kraft
307.4010
Papergrade Sulfite
(Blow Pit Wash)
307.4011
Dissolving Sulfite Pulp
307.4012
Groundwood—Chemi—Mechanical
307.4013
Groundwood—Thermo—Mechanical
307.4014
Groundwood—CMN Papers
307.4015
Groundwood—Fine Papers
307.4016
Soda
307.4017
Deink
307.4018
Nonintegrated—Fine Papers
307.4019
Nonintegrated—Tissue
Papers
307.4020
Tissue From Wastepaper
307.4021
Papergrade Sulfite
(Drum Wash)
307.4022
Unbleached Kraft and Semi—Chemical
307.4023
Wastepaper—Molded Products
307.4024
Nonintegrated—Lightweight Papers
307.4025
Non3.ntegrated—Filter
and Nonwoven Papers
307.4026
Nonintegrated—Paperboard
SUBPART BF:
BUILDERS’ PAPER AND BOARD MILLS
Section
307.4101
Builder’s Paper
and Roofing Felt
SUBPART BG:
MEAT PRODUCTS
Section
307.4201
Simple Slaughterhouse
307.4202
Complex Slaughterhouse
307.4203
Low—Processing Packinghouse
307.4204
High—Processing Packinghouse
307.4205
Small Processor
307.4206
Meat Cutter
307.4207
Sausage and Luncheon Meats Processor
307.4208
Ham Processor
307.4209
Canned
Meats Processor
307.4210
Renderer
79-355

—10—
SUBPART BR:
METAL FINISHING
Section
307.4301
Metal Finishing
SUBPART BN:
PHARMACEUTICAL MANUFACTURING
Section
307.4900
307.4901
307.4902
307.4903
307.4904
307.4905
General Provisions
Fermentation Products
Extraction Products
Chemical Synthesis Products
Mixing/Compounding and Formulation
Research
SUBPART BR:
PAVING AND ROOFING MATERIALS
(TARS AND ASPHALT)
Section
307.5301
307.5302
307.5303
307.5304
Asphalt Emulsion
Asphalt Concrete
Asphalt Roofing
Linoleum and Printed Asphalt Felt
SUBPART BU:
PAINT FORMULATING
Section
307.5601
Oil—Base Solvent Wash Paint
SUBPART BV:
INK FORMULATING
Section
307.5701
Oil—Base Solvent Wash Ink
SUBPART CD:
PESTICIDE CHEMICALS
Section
307.6500
307.6501
307.6502
307.6503
307.6504
General Provisions
Organic Pesticide Chemicals Manufacturing
Metallo—Organic Pesticides Chemicals Manufacturing
Pesticide Chemicals Formulating and Packaging
Test Methods for Nonconventional Pesticide Pollutants
SUBPART CG:
CARBON BLACK MANUFACTURING
Section
307.6801
307.6802
307.6803
307.6804
Carbon Black Furnace Process
Carbon Black Thermal Process
Carbon Black ~ChanrielProcess
Carbon Black Lamp Process
SUBPART CJ:
BATTERY MANUFACTURING
Section
79-356

—11—
307.7100
307.7101
307.7102
307.7103
307.7104
307.7105
307. 7106
307.7107
General Provisions
Cadmium
Calcium
Lead
Leclanche
Lithium
Magnesium
Zinc
SUBPART CL:
PLASTICS MOLDING AND FORMING
Section
307.7300
307.7301
307.7302
307.7303
General
Provisions
Contact Cooling and Heating Water
Cleaning Water
Finishing Water
SUBPART CM:
METAL MOLDING AND CASTING
Section
307.7400
307.7401
307.7402
307.7403
307.7404
General Provisions
Aluminum Casting
Copper Casting
Ferrous Casting
Zinc Casting
SUBPART CN:
COIL COATING
Section
307.7500
307.7501
307.7502
307.7503
307.7504
Genera? Provisions
Steel Basis Material
Galvanized Basis Material
Aluminum Basis Material
Canmaking
SUBPART CO:
PORCELAIN ENAMELING
Section
307.7600
307.7601
307.7602
307.7603
307.7604
General Provisions
Steel
Basis Material
Cast Iron Basis Material
Aluminum Basis Material
Copper Basis Material
SUBPART CP:
ALUMINUM FORMING
Section
307.7700
307.7701
307.7702
307.7703
307.7704
307.7705
307.7706
General Provisions
Rolling With Neat Oils
Rolling With Emulsions
Extr usion
Forg ing
Drawing ~cithNeat Oils
Drawing With Emulsions or Soaps
79-357

—12—
General Provisions
_________
Copper
Forming
_________
Beryllium Copper
Forming
SUBPART CR:
ELECTRICAL AND ELECTRONIC COMPONENTS
Section
307.7901
Semiconductor
307.7902
Electronic Crystals
307.7903
Cathode Ray Tube
307.7904
Luminescent Materials
SUBPART CT:
NONFERROUS
METALS
FORMING
AND
METAL POWDERS
_________
General Provisions
_________
Lead—Tin—Bismuth
Forming
_________
Magnesium Forming
_________
Nickel—Cobalt Forming
_________
Precious
Metals
Forming
_________
Refractory Metals Forming
_________
Titanium
Forming
_________
Uranium
Forming
________
Zinc
Forming
_________
Zirconium—Hafnium
Forming
_________
Metal
Powders
Appendix
References
to Previous Rules
(Repealed)
AUTHORITY:
Implementing
Sections
13
and
13.3
and
authorized
by
Section
27
of
the
Environmental
Protection
Act,
as
amended
by
P.A.
84—1320, effective September
4,
1986
(Ill.
Rev.
Stat.
1985,
ch. 111 1/2, pars.
1013 and 1027, and Ill.
Rev.
Stat.
1986 Supp.,
ch.
111 1/2, par.
1013.3.
SOURCE:
Adopted
in
R70—5,
at
1
PCB
426,
March
31,
1971;
amended
in
R7l—14,
at
4
PCB
3,
March
7,
1972;
amended
in
R74—3,
at
19
PCB
182,
October
30,
1975;
amended
in
R74—l5,
16,
at
31
PCB
405,
at
2
Ill.
Reg.
no.
44,
page 151, effective November
2,
1978;
amended
in
R76—17,
at
31
PCB
713,
at
2
Ill.
Reg.
no.
45, page
101,
effective
November
5,
1978;
amended
in
R76—2l,
at
44
PCB
203,
at
6
Ill.
Reg.
563,
effective
December
24,
1981;
codified
at
6
Ill.
Reg.
7818;
amended
in
R82—5,
10,
at
54
PCB
411,
at
8
Ill. Reg.
1625, effective January 18,
1984;
amended
in R86—44
at
11
Ill.
Reg.
,
effective
SUBPART A:
GENERAL PROVISIONS
Section 307.101
Preamble
(Renumbered)
Section
307.7800
307.7801
307.7802
SUBPART CO:
COPPER FORMING
Section
307.8100
307.8101
307.8102
307.8103
307.8104
307.8105
307.8106
307.8107
307.8108
307.8109
307.8110
79-358

—13—
(Source:
Section 307.101
renumbered
to Section 307.1001 at
Ill.
Reg.
,
effective
)
Section
307.102
General
Requirements
(Renumbered)
(Source:
Section
307.102 renumbered
to
Section 307.1101 at
Ill. Reg.
,
effective
)
Section
307.103
Mercury
(Renumbered)
(Source:
Section 307.103 renumbered
to Section 307.1102
at
Ill.
Reg.
,
effective
Section
307.104
Cyanide
(STORET
number
00720)
(Renumbered)
(Source:
Section 307.104 renumbered to Section 307.1103 at
Ill.
Reg.
,
effective
)
Section 307.105
Pretreatment Requirements
(Repealed)
~
e~er~ ~e t~ereq
remert~ee~See*.~erte38
39~y
3~T~8
~i~d
~~4y
i’~e ~
~
el’~erqef~e any
4e3y ewned ~fee~eI~t
wer1~e may
ee1’~ge
any
e~en~
to
eue~
b4~e~yowned treeti~ent
we~ke 4n
vte~etten
e~
reg
et4ene prom
gated by t1~e
pt~re~an~
to
Geetton
9~9~+~+
e~ tI’~e?W~ w’~en e~e~
re~at~ens~eeeme e~eete7
(Source:
Repealed
at
Ill.
Reg.
effective
Section 307.~8~l00lPreamble
a)
This Part 3&~places certain restrictions on the types,
concentrations and quantities of contaminants which can
be discharged into sewer systems
in the State.
Bn~es~
ti~eeentrafy ~s e~eer~ytnd±eeted7a~ re~ereneesto
er ~Seet~en&1 are to ~
xdfft~
eede7
T~t~e35~
Benmente~ Preteet~en~Fee e~amp~e7
~Peet
399fl 4o 35
~
Adm~eode 3~97and ~‘Seet~ion3G9~9~to
35 ~H-~
Ad~-eode 3G7~G~
1)
Subpart
B includes standards
for
the discharge of
contaminants
to sewer systems.
These apply to
dischargers to publicly owned treatment works
(POTW’s)
and
to dischargers
to other
types
of
treatment works
as specified
in each Section.
2)
Subparts
F et seq.
include standards
for
the
discharge
of contaminants from certain
industrial
categories
into POTW’s.
b)
35 Ill.
Adm.
Code 310 specifies requirements for
pretreatment programs
for POTW’s.
79-359

—14—
c)
This Part incorporates by reference federal regulations.
1)
Such incorporations include no later
amendments
or
editions.
2)
Except where
the contrary is clearly indicated,
the
Board intends
to set forth all procedural
requirements
in full
in this Part and
35
Ill. Adm.
Code 310, and
to utilize only the definitions,
requirements
or standards from the incorporated
material.
3)
Except
where
the
contrary
is
clearly
indicated,
references
to other
federal
regulations within
incorporated material
are to be construed
as
referencing Board
regulations derived from the
referenced
material,
rather
than
the
other
federal
regulation.
(Source:
Section 307.1001 renumbered
from Section 307.101 and
amended at
Ill. Reg.
,
effective
)
Section 307.1002
Definitions
a)
The definitions of
35 Ill.
Adm. Code 301
do not apply to
this Part.
b)
The definitions of
35
Ill. Adm. Code 310 apply to this
Part.
(Source:
Added at
Ill.
Reg.
effective
)
Section 307.1003
Test Procedures
for Measurement
The Board incorporates by reference
40 CFR 136 and 401.13
(1986).
This incorporation includes no later
amendments or
editions.
(Source:
Added
at
Ill. Reg.
effective
)
Section 307.1005
Toxic Pollutants
The Board
incorporates by reference
40 CFR 401.15
(1986).
This
incorporation includes no later
amendments or
editions.
(Source:
Added
at
Ill. Reg.
effective
Section 307.1007
pH Limitations under Continuous Monitoring
a)
If
a person continuously measures the
pH of wastewater,
such person shall maintain the pH of the wastewater
79-360

—15—
within
the
range
set
forth
in the applicable standards,
except
for excursions within the following limitations:
1)
The
total
time
during
which
the
pH
values
are
outside
the
required
range
shall
not
exceed
7
hours
and
26 minutes
in any calendar month;
and
2)
No individual excursion shall exceed 60 minutes.
b)
An excursion
is
an unintentional and temporary incident.
(Source:
Added
at
Ill.
Reg.
effective
)
SUBPART
B:
GENERAL
AND SPECIFIC PRETREATMENT REQUIREMENTS
Section 307.3~~llOlGeneraland Specific Requirements
Any wastes d~oekergedte any sewer owned
by any m~n~e~pa~ty7
any
eet~nty7or any oeMtery 44etc4et
4n the State e~~
ohe~
meet
the
~o~ew~ng
er~tee4a~n edd~t4ento any eetab~4shedby the
~
eot~nty
or
sen4tery d4otr4et 4toe~i-
a+
I~qt~ds7eo~ds7or gases whieh by reason e~their
net~eeor q~ant~tymay ea~se~re
or exp~ee~onter ~e
~n~r~e~s
~n any other way te
SCWCC 57
treatment we~4t~~
stf~et~res
or
to
the
eperat4en
e~ treatment
works7
or
cause a safety ha?erd to
the
peesenne3 eperet~4ng
the
treatment
werk~7 or
cause
the
e~~uent~rem the
treatment werke to v~e~eteepp~eab~ee~~uentotndards
are pro
b~ted~
~3
So~~d
or v~seouswastes wh~ehcause ebstruet4en to the
f~ew~n sewers or
other
~nter~erenee wtth
the
proper
eperet~ono~any sewer or treatment works are
pcoM~4ted-
No person shall introduce the following types
of pollutants into
a
POTW:
a)
General
requirements.
1)
Pollutants
which
pass
through
the
POTW.
2)
Pollutants which interfere with the operation or
performance
of the POTW.
b)
Specific requirements.
1)
Pollutants which create
a fire or explosion hazard
within
the POTW.
2)
Pollutants which
would
cause safety hazards
to
the
personnel operating
the treatment works
79-361

—16—
3)
Pollutants which will cause corrosive damage
to the
POTW.
4)
Pollutants which would
be injurious
in any other
way to sewers, treatment works
or structures.
5)
Discharges with
a pH less than 5.0, unless
the POTW
is specifically designed
to accommodate such
discharges.
6)
Solid
or
viscous pollutants
in amounts which will
cause obstruction to the flow in the POTW resulting
in
interference.
7)
Any pollutant,
including oxygen demanding
pollutants,
at a flow rate or concentration which
will
cause
interference
with
the
POTW.
8)
Heat
in amounts which will inhibit biological
activity
in
the
POTW and interfere with the POTW.
9)
Heat
in amounts which results
in temperatures
in
the
influent
to
the
POTW
treatment
plant
in
excess
of
40 degrees
C
(104 degrees
F)
unless the Agency
approves alternate temperature limits
in
pretreatment plan.
10)
Pollutants
which would
cause
the effluent from the
treatment works
to violate applicable effluent
standards
(Source:
Section 307.1101 renumbered from Section 307.102
and
amended
at
Ill.
Reg.
,
effective
)
Section 307.~9ll02Mercury
a)
Except as provided below,
no person shall
cause
or allow
the concentration of mercury
in any discharge to a
publicly owned
or publicly regulated sewer
system
to
exceed
the following
level, subject
to the averaging
rule contained
in 35
Ill. Adm. Code 304.104(a):
STORET
CONCENTRATION
CONSTITUENT
NUMBER
mg/i
Mercury
71900
0.0005
b)
It shall
be
an exception
to paragraph subsection
(a)
if
the discharge
is to
a publicly owned
or publicly
regulated sewer system which is required
to
meet
a
limitation less stringent than the 0.0005 mg/l mercury
79-362

—17—
concentration
in
which
case
the discharge limitation
shall be the same as that applicable to the publicly
owned
or regulated sewer system to which it discharges.
c)
It shall
be an exception to paragraph subsection
(a)
if
all the following conditions are met:
1)
The discharger does not use mercury; or,
the
discharger uses mercury and this use cannot be
eliminated;
or, the discharger uses mercury only in
chemical analysis or
in laboratory or other
equipment and takes reasonable care
to avoid
contamination of wastewater;
and,
2)
The discharge mercury concentration is less than
0.003 mg/i,
as determined by application of the
averaging rules of
35 Ill.
Adm. Code 304.104(a);
and,
3)
The discharger
is providing the best degree of
treatment consistent with technological
feasibility,
economic
reasonableness and sound
engineering judgment.
This may include no
treatment for mercury;
and,
4)
The discharger has
an inspection and maintenance
program likely to reduce or
to prevent
an
increase
in the level
of mercury discharges.
d)
The discharge of wastes from medicinal or therapeutic
use of mercury, exclusive of laboratory
use,
shall be
exempt from the limitations
of paragraph subsection
(a)
e~th~eseet~enif all the following conditions are met:
1)
The total plant discharge is less than 227
g (one
half pound)
as Hg
in any year;
2)
This discharge
is
to
a public sewer
system; and
3)
The discharge does not,
alone
or
in conjunction
with other
sources, cause the effluent from the
sewer system or
treatment plant
to exceed 0.0005
mg/i of mercury.
e)
No person shall cause
or allow any discharge of mercury
to
a publicly owned or publicly regulated sewer
system
which, alone
or
in combination with other sources,
causes
a violation by the sewer
treatment plant
discharge
of the water quality standard
of 35
Iii.
Adm.
Code Fart
302
for mercury applicable
in the receiving
stream.
f)
For purposes
of permit
issuance the Agency may consider
application of the exception of paragraph subsection
(b)
79-363

—18—
or
(C)
to determine compliance with this Section.
The
Agency may impose permit conditions necessary or
required
to assure continued application of the
exception.
When paragraph subsection
(b)
or
(C)
applies,
the
Agency
may
impose
an
effluent
limitation
in
the permit which allows
the discharge of
a concentration
of mercury greater than 0.0005 mg/i but not more than
0.003 mg/i.
(Source:
Section 307.1102 renumbered from Section 307.103 and
amended at
Ill.
Reg.
,
effective
)
Section 307.~44ll03
Cyanide *SP9REP rtam~erO6~&+
a)
No waste
to any public
sewer system shall contain more
than
10 mg/l total cyanide
(STORET number 00720)
provided any sample tested
shall not release more than
2
mg/i
of cyanide when
tested at
a pH of 4.5 and at a
temperature of 662 degrees
C
(1502 degrees
F)
for
a
period
of
30 minutes, except as permitted by paragraph
subsection
(b).
b)
Upon application by a county, municipality, sanitary
district or public utility and approval by the Agency,
based upon determination by the Agency that
no violation
of
the effluent ee~ter~ao~th~schapter standards of
35
Iii. Adm.
Code
104 will result and that no hazard
to
workers
in such sewage works will result,
limited
additional
amounts of cyanide exceeding
the standards
in
paragraph subsection
(a) may be discharged
to the sewage
works of such county,
sanitary district, municipality or
public utility.
C)
Nothing
in this Section shall
be construed
as limiting
the authority of any county, municipality, sanitary
district or public
utility to
impose any more stringent
standards or
limitations on cyanide discharges
to
its
sewage works.
(Source:
Section 307.1103
renumbered from Section 307.104 and
amended at
Iii.
Reg.
,
effective
)
SUBPART F:
DAIRY PRODUCTS PROCESSING
Section 307.1501
Receiving Stations
a)
Applicability.
This Section applies to discharges
resulting from the operation
of receiving stations
engaged
in
the assembly and reshipment
of bulk milk for
the
use of manufacturing
or processing plants.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 405.11
(1986).
This incorporation
includes no
later
amendments or
editions.
79-364

—19—
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 405.14
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.16
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced
after
December
20,
1973.
(Source:
Added at 11 Ill. Reg.
effective
)
Section 307.1502
Fluid Products
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of market milk (ranging
from 3.5
fat
to fat—free),
flavored milk (chocolate
and
others)
and cream
(of various fat concentrations, plain
and whipped).
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 405.21
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 405.24
(1986).
This incorporation includes
no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
79-365

—20—
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 405.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation
of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced
after
December
20,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.1503
Cultured Products
a)
Applicability.
This Section applies
to discharge~.
resulting from the manufacture of cultured products,
including cultured skim milk (cultured buttermilk),
yoghurt,
sour cream and dips
of various
types.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 405.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 405.34
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POT~~
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.36
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
79-366

—21—
standards.
3)
“New
source” means any building., structure,
facility
or
installation
the
construction
of
which
commenced
after
December
20,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.1504
Butter
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of butter,
either by
churning or continuous process.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 405.41
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 405.44
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to
the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of
any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
20,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.1505
Cottage Cheese and Cultured Cream Cheese
a)
Applicability.
This Section applies to discharges
resulting
from
the manufacture
of
cottage cheese
and
79-367

—22—
cultured
cream
cheese.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 405.51
(1986).
This incorporation
includes
no later
amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 405.54
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.56
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
20,
1973.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.1506
Natural
and Processed Cheese
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of natural cheese
(hard
curd)
and processed cheese.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 405.61
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 405.64
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
79-368

—23—
incorporated by reference in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a
POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 405.66
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
20,
1973.
(Source:
Added
at ii Ill.
Reg.
effective
)
Section 307.1507
Fluid Mix
for
Ice Cream and
other Frozen
Desserts
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of fluid mixes
for ice
cream and other
frozen desserts for
later
freezing
in
other plants;
it does not include freezing of the
products as one of the affected operations.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 405.71
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates
by
reference
40 CFR 405.74
(1986).
This incorporation includes
no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 405.76
(1986).
This incorporation includes
no later
amendments or
editions.
79-369

—24—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or
installation the construction of which
commenced
after
December
20,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.1508
Ice Cream, Frozen Desserts, Novelties and
Other Dairy Desserts
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of
ice cream,
ice milk,
sherbert, water
ices, stick confections, frozen
novelties products, frozen desserts, melorine, pudding
and other dairy product base desserts.
If fluid mixes
prepared at another plant are employed,
the appropriate
values from Section 307.1507 should
be deducted
from the
limitations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 405.81
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 405.84
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 405.85
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
79-370

—25—
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after December
20, 1973.
(Source:
Added
at
ii
Ill.
Reg.
effective
Section 307.1509
Condensed Milk
a)
Applicability.
This Section applies to discharges
resulting from the manufacture
of condensed whole milk,
condensed skim milk,
sweetened condensed milk and
condensed butter milk.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 405.91
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 405.94
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POT~in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after December
20,
1973.
(Source:
Added
at
11
Iii.
Reg.
effective
)
Section 307.1510
Dry Milk
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of dry whole milk,
dry
skim milk and dry buttermilk.
79-371

—26—
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 405.101
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 405.104
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.106
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced
after
December 20,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.1511
Condensed Whey
a)
Applicability.
This Section applies to discharges
resulting
from the manufacture of condensed
sweet whey
and condensed acid whey.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 405.111
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 405.114
(1986).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
79-372

—27—
cause,
threaten or allow
the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 405.116
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation
of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
December
20,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.1512
Dry Whey
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of sweet
or acid dry
whey.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 405.121
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 405.124
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 405.126
(1986).
This
incorporation
includes
no
later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated
by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
79-373

—28—
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
20,
1973.
(Source:
Added at
11
Ill. Reg.
effective
)
SUBPART G:
GRAIN MILLS
Section
307.1601
Corn Wet Milling
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which shelled corn
is
steeped
in
a dilute solution of sufurous acid and then
processed by wet means
into such products
as animal
feed, regular and modified starches,
corn oil, corn
syrup and dextrose.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.11
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 406.14
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates
by
reference
40 CFR 406.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
4,
1973.
(Source:
Added
at 11 Ill.
Reg.
79-374

—29—
effective
Section 307.1602
Corn Dry Milling
a)
Applicability.
This Section applies to discharges
resulting from the process
in which shelled corn
is
washed and subsequently milled by dry processes into
such products as corn meal, grits,
flour, oil and animal
feed.
This Section does not apply to discharges from
subsequent manufacturing operations to produce expanded
or extruded feed or feed products.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 406.21
(1986).
This incorporation
includes
no
later
amendments
or
editions.
c)
Existing
sources:
1)
The Board incorporates by reference
40 CFR 406.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 406.26
(1986).
This
incorporation
includes
no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after December
4,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.1603
Normal Wheat Flour Milling
a)
Applicability.
This Section applies to discharges
resulting from the processes
in which wheat and other
grains are milled by dry processes into
flour
and
millfeed.
79-375

—30—
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.31
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 406.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 406.36
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a PQTW
in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after
December
4,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section
307.1604
Bulgur
Wheat
Flour
Milling
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which wheat
is parboiled,
dried and partially debranned
in the production of
bulgur.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.41
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 406.44
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
79-376

—31—
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 406.46
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after
December
4,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.1605
Normal Rice Milling
a)
Applicability.
This Section applies to discharges
resulting from the process
in which rice is cleaned and
milled
by dry processes.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.51
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 406.54
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge
of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The
Board
incorporates
by
reference
40
CFR
406.56
(1986).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-377

—32—
cause,
threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
4,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.1606
Parboiled Rice Milling
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which rice
is cleaned,
cooked
and dried before being milled.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 406.61
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 406.64
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 406.66
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
~j
“New source” means any building,
structure,
facility or
installation the construction
of which
commenced
after
December
4,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.1607
Animal
Feed
79-378

—33—
a)
Applicability.
This Section applies to discharges
resulting from the manufacturing
of animal feeds
(formula feed concentrate)
using primarily grain and
grain by—products which may be supplemented by proteins,
pharmaceuticals,
vitamins or mineral additives.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 406.71
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:,
These
sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 406.76
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after September
17,
1974.
(Source:
Added at
11
Ill. Reg.
effective
)
Section 307.1608
Hot Cereal
a)
Applicability.
This Section applies to discharges
resulting from the production of various breakfast
cereals from grains, principally wheat
and oats,
requiring cooking prior
to normal human consumption.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.81
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
These sources shall
comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 406.86
(1986).
This incorporation includes no later
amendments
or editions.
79-379

—34—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation
of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after September 17,
1974.
(Source:
Added
at 11
Ill. Reg.
effective
)
Section 307.1609
Ready—to—eat Cereal
a)
Applicability.
This Section applies
to discharges
resulting from the processing
of various grains and
other materials
(whole grain wheat,
rice,
corn grits,
oat flour, sugar
and minor
ingredients)
to produce
various breakfast cereals normally available for human
consumption without cooking.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.91
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 406.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after September
17,
1974.
(Source:
Added
at 11
Ill. Reg.
,
effective
Section 307.1610
Wheat Starch and Gluten
a)
Applicability.
This Section applies
to discharges
resulting from those
industrial
operations utilizing
wheat
flour
as
a
raw material
for production of wheat
79-380

—35—
starch and gluten
(protein) components through
conventional processes of physical
separation and
subsequent refinement.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 406.101
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 406.106
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after September
17,
1974.
(Source:
Added
at
11
Ill.
Reg.
effective
SUBPART
H:
CANNED AND PRESERVED FRUITS AND VEGETABLES
Section 307.1700
General
Provisions
Proration.
When
a plant
is subject
to limitations covering more
than one subcategory, the plant discharge limitation shall
be set
by proration limitations
for each subcategory based
on the total
raw material
covered by each subcategory.
(Source:
Added
at
Ill. Reg.
effective
)
Section 307.1701
Apple Juice
a)
Applicability.
This Section applies to discharges
resulting from the processing of apples
into apple
juice
or
apple cider.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.11
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
79-381

—36—
1)
The Board incorporates
by
reference 40 CFR 407.14
(1986).
This
incorporation includes no later
amendments or editions.
2)
No
person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 407.16
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after November
9,
1974.
(Source:
Added
at 11
Ill. Reg.
,
effective
)
Section 307.1702
Apple Products
a)
Applicability.
This Section applies
to discharges
resulting from the processing
of apples
into apple
products.
The processing
of apples into caustic peeled
or dehydrated products
is specifically excluded.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.21
(1986).
This incorporation
includes
no later amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 407.24
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New
sources:
79-382

—37—
1)
The Board incorporates by reference
40 CFR 407.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
9,
1974.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.1703
Citrus Products
a)
Applicability.
This Section applies to discharges
resulting from the processing
of citrus
into citrus
products.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.31
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 407.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
d)
New sources:
fl
The Board incorporates
by
reference 40 CFR 407.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
79-383

—38—
commenced after November
9,
1974.
(Source:
Added at
11
Ill. Reg.
effective
)
Section 307.1704
Frozen Potato Products
a)
Applicability.
This Section applies
to discharges
resulting from the processing
of white potatoes onto
frozen potato products.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.41
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
The Board incorporates by reference
40 CFR 407.44
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of
such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 407.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building, structure,
facility
or
installation
the
construction
of
which
commenced after November
9,
1974.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.1705
Dehydrated Potato Products
a)
Applicability.
This Section applies to discharges
resulting from the processing of white potatoes into
dehydrated potato products.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.51
(1986).
This incorporation
79-384

—39—
includes no later amendments
or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 407.54
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 407.56
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or
installation the construction of which
commenced after November
9,
1974.
(Source:
Added at 11
Ill.
Reg.
effective
Section 307.1706
Canned and Preserved
Fruits
a)
Applicability.
This Section applies to discharges
resulting
from the processing
of the following
fruit
products:
apricots; caneberries; sweet,
sour and brined
cherries; cranberries; dried
fruit; grape juice canning
and pressing;
olives; peaches; pears;
fresh
and
processed pickles, and pickle salting stations;
pineapples; plums;
raisins; strawberries; and
tomatoes.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 407.61
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 407.64
(1986).
This incorporation includes no
later
amendments
or editions.
79-385

—40—
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by
reference 40 CFR 407.66
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
~j
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
21,
1975.
(Source:
Added
at 11
Ill. Reg.
,
effective
)
Section 307.1707
Canned and Preserved Vegetables
a)
Applicability.
This Section applies
to discharges
resulting from the processing
of the following vegetable
products:
beets;
broccoli;
carrots; canned and frozen
corn; dehydrated onions and garlic; dehydrated
vegetables;
dry beans; lima beans; mushrooms;
canned
onions; peas;
sauerkraut canning and cutting;
snap
beans; spinach; squash; and canned potatoes.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.71
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 407.74
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(I) shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 407.76
79-386

—41
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after October
21,
1975.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.1708
Canned
and Miscellaneous Specialties
a)
Applicability.
This Section applies
to discharges
resulting from
the processing
of the following specialty
products:
added ingredients; baby food; corn,
potato
and tortilla chips; ethnic
foods;
jams and
jellies;
mayonnaise
and dressings;
soups;
and tomato—starch—
cheese canned
specialties.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 407.81
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 407.84
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 407.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow
the discharge of
any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
79-387

—42—
facility or
installation the construction of which
commenced after October
21,
1975.
(Source:
Added at
11
Ill.
Reg.
effective
SUBPART
I:
CANNED AND PRESERVED SEAFOOD
Section 307.1801
Farm—raised Catfish
a)
Applicability.
This Section applies to discharges
resulting from
the processing
of farm—raised catfish by
existing facilities which process more than 1362 kg
(3000
lbs)
of raw material per day on any day during
a
calendar year and all new sources.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 408.11
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 408.14
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 408.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 6,
1974.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.1815
Fish Meal Processing Subcategory
79-388

—43—
a)
Applicability.
This Section applies
to discharges
resulting from the processing of menhaden on the Gulf
and Atlantic Coasts and the processing of anchovy on the
West Coast
into fish meal,
oil and
solubles.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 408.151
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 408.154
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 408.156
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 30,
1975.
(Source:
Added
at 11
Ill.
Reg.
effective
SUBPART
J:
SUGAR PROCESSING
Section 307.1901
Beet Sugar Processing
a)
Applicability.
This Section applies
to discharges
resulting from any operation attendant to the processing
of sugar
beets
for the production of sugar.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 409.11
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
79-389

—44—
1)
The Board incorporates by reference
40 CFR 409.14
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 409.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation
the construction of which
commenced after August
22,
1973.
(Source:
Added
at
11
Ill.
Reg.
,
effective
)
Section 307.1902
Crystalline Cane Sugar Refining
a)
Applicability.
This Section applies
to discharges
resulting from the processing of raw cane sugar
into
crystalline refined sugar.
b)
Specialized
definitions.
The
Board
incorporates
by
reference 40 CFR 409.21
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 409.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
I)
The
Board
incorporates
by
reference
40
CFR
409.26
79-390

—45—
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
7,
1973.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.1903
Liquid Cane Sugar
Refining
a)
Applicability.
This Section applies to discharges
resulting
from
the processing
of raw cane sugar
into
liquid refined sugar.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 409.31
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 409.34
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates
by
reference 40 CFR 409.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of
any
contaminant to
a POT~in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation the construction of which
commenced after December
7,
1973.
79-391

—46—
(Source:
Added at
11 Ill.
Reg.
effective
)
SUBPART
K:
TEXTILE MILLS
Section 307.2000
General Provisions
a)
Applicability.
This Subpart applies
to any textile mill
or textile processing facility which introduces
or may
introduce process wastewater pollutants into
a POTW.
b)
General definitions.
The Board incorporates by
reference 40 CFR 410.01
(1986).
This incorporation
includes no later amendments
or editions.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2001
Wool Scouring
a)
Applicability.
This Section applies
to discharges
resulting from the following types
of textile mills:
wool scouring,
topmaking, and general cleaning
of raw
wool.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 410.11
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 410.14
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New
sources:
1)
The Board incorporates by reference
40 CFR 410.16
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation
of
such
standards.
3)
“New
source”
means
any
building,
structure,
79-392

—47—
facility or installation the construction of which
commenced after October
10,
1979.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.2002
Wool Finishing
a)
Applicability.
This Section applies
to discharges
resu1tin~from the following types of textile mills:
wool finishers,
including carbonizing, fulling, dyeing,
bleaching, rinsing,
fireproofing, and other such similar
processes.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 410.21
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 410.24
(1986).
This incorporation includes no later
amendments
or editions.
2)
No
person subject
to the pretreatment standards
incorporated
by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 410.26
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
10,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2003
Low Water
Use Processing
a)
Applicability.
This Section applies
to discharges
resulting from the following types of textile mills:
yarn manufacture, yarn texturizing,
unfinished fabric
79-393

—48—
manufacture,
fabric coating,
fabric laminating,
tire
cord and fabric dipping,
and carpet tuftin~and carpet
backing.
Rubberized or rubber coated fabrics regulated
by 40 CFR Part 428 are specifically excluded.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 410.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
~j
The Board incorporates
by
reference
40 CFR 410.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by
reference
40 CFR 410.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October 10,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.2004
Woven Fabric
Finishing
a)
Applicability.
This Section applies
to discharges
resulting
from
the following types of textile mills:
woven
fabric finishers, which may include any or all
of
the
following unit operations:
desizing, bleaching,
mercerizing, dyeing, printing,
resin treatment, water
proofing, flame proofing,
soil repellency application
and
a special finish application.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 410.41
(1986).
This incorporation
includes
no later
amendments
or editions.
79-394

—49—
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 410.44
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 410.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after October
10,
1979.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.2005
Knit Fabric Finishing
a)
Applicability.
This Section applies to discharges
resulting from the following types
of textile mills:
knit fabric finishers, which may include any or
all of
the following
unit operations:
bleaching, mercerizing,
dyeing,
printing, resin treatment,
water proofing, flame
proofing,
soil repellency application and
a special
finish application.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 410.51
(1986).
This incorporation
includes
no later amendments
or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 410.54
(1986).
This incorporation includes
rio
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
79.395

—50—
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 410.56
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction
of which
commenced after October
10,
1979.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.2006
Carpet Finishing
a)
Applicability.
This Section applies to discharges
resulting from the following types of textile mills:
carpet mills, which may include any or all
of the
following unit operations:
Bleaching, scouring,
carbonizing,
fulling, dyeing, printing,
resin treatment,
waterproofing, flameproofing,
soil repellency, looping,
and backing with foamed
and unfoamed latex and jute.
Carpet backing without other carpet manufacturing
operations
is included
in Subpart
C.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 410.61
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 410.64
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 410.66
(1986).
This incorporation includes no later
79-396

—51—
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October 10,
1979.
(Source:
Added at
11 Ill.
Reg.
effective
Section 307.2007
Stock and Yarn Finishing
a)
Applicability.
This Section applies to discharges
resulting from the following types of textile mills:
stock or yarn dyeing
or finishing, which may include any
or all
of the following unit operations and processes:
cleaning, scouring, bleaching, mercerizing, dyeing and
special
finishing.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 410.74
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 410.76
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced after October
10,
1979.
79-397

—52—
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2008
Nonwoven Manufacturing
a)
Applicability.
This Section applies to discharges
resulting from facilities that primarily manufacture
nonwoven
textile
products
of
wool,
cotton,
or
synthetics, singly or
as blends, by menchanical,
thermal, and/or adhesive bonding procedures.
Nonwoven
products produced by fulling and felting processes are
covered
in Section 307.2009
——
Felted Fabric Processing.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 410.84
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 410.86
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
10,
1979.
(Source:
Added
at 11
Ill. Reg.
effective
)
Section 307.2009
Felted Fabric Processing
a)
Applicability.
This Section applies
to discharges
resulting
from facilities that primarily manufacture
nonwoven products by employing
fulling and felting
operations as
a means of achieving
fiber bonding.
b)
Specialized definitions.
None.
79-398

—53—
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 410.94
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation
of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 410.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
10,
1979.
(Source:
Added at
11
Ill.
Reg.
effective
)
SUBPART
L:
CEMENT MANUFACTURING
Section 307.2101
Nonleaching
a)
Applicability.
This Section applies to discharges
resulting
from
the process
in which several mineral
ingredients
(limestone
or other
natural sources of
calcium carbonate, silica, alumina, and
iron together
with gypsum)
are used
in the manufacturing
of cement and
in which
kiln dust
is not contracted with water
as an
integral part of the process and water
is not used
in
wet scrubbers
to control
kiln stack emissions.
b)
Specialized definitions.
The Board incorporates by
reference 40
CFP. 411.11
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 411.14
(1986).
This incorporation includes no later
amendments
or editions.
79-399

—54—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 411.16
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
September
7,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2102
Leaching
a)
Applicability.
This Section applies to discharges
resulting from the process
in which several mineral
ingredients
(limestone or other natural sources of
calcium carbonate,
silica, alumina,
and
iron together
with gypsum)
are used inthe manufacturing
of cement and
in which kiln dust
is contacted with water
as an
integral part of the process
or water
is used in wet
scrubbers to control
kiln stack emissions.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 411.21
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 411.24
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
79.400

—55—
1)
The Board
incorporates by reference 40 CFR 411.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after September
7,
1973.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.2103
Materials Storage Piles Runoff
a)
Applicability.
This Section applies
to discharges
resulting from the runoff
of rainfall which derives from
the storage of materials including raw materials,
intermediate products,
finished products and waste
materials which are used in
or derived from the
manufacture of
cement under
either Section 307.2101
or
307.2102
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 411.31
(1986).
This incorporation
includes no
later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 411.34
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 411.36
(1986).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of
any
contaminant
to
a POTW
in violation of
such
79.401

—56—
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after September 7,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
)
SUBPART M:
FEEDLOTS
Section 307.2201
General
a)
Applicability.
This Section applies to discharges
resulting from feedlots
in the following
subcategories:
Beef cattle
——
open lots;
beef cattle
——
housed
lots;
dairy cattle
——
stall barn
(with milk
room);
dairy
——
free stall
barn
(with milking center);
dairy
——
cowyards (with milking center);
swine
——
open
dirt or pasture lots;
swine
——
housed, slotted
floor;
swine
—-
solid concrete
floor, open
or housed lot;
sheep
——
open lots;
sheep
——
housed
lots; horses
——
stables
(race tracks); chickens
——
broilers, housed; chickens
——
layers
(egg production), housed; chickens
——
layer
breeding
or replacement
stock; housed;
turkeys
——
open
lots;
turkeys
——
housed;
and
for
those feedlot
operations within
these subcategories as large or larger
than the capacities given below:
1,000 slaughter steers
and heifers;
700 mature dairy cattle (whether milkers or
dry cows);
2,500 swine weighing over 55 pounds;
10,000
sheep;
55,000 turkeys, 100,000 laying hens
or broilers
when facility has unlimited continuous flow watering
systems;
30,000 laying hens
or broilers when facility
has liquid manure handling system;
500 horses;
and 1,000
animal units from a combination of
slaughter steers and
heifers, mature dairy cattle,
swine over
55 pounds and
sheep.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 412.11
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing sources:
I)
The Board
incorporates by reference
40 CFR 412.14
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POT~in violation of
such
standards.
79.402

—57—
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 412.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
“New source” means any building, structure,
facility or installation
the construction of which
commenced after September 7,
1973.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.2202
Ducks
a)
Applicability.
This Section applies to discharges
resulting from feedlots for the following
subcategories:
Ducks
——
dry lot; ducks
——
wet lot; and
for those feedlot operations within these subcategories
as large or
larger than the capacities given below:
5,000 ducks.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 412.21
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 412.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 412.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
79-403

—58—
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after September
7, 1973.
(Source:
Added
at
11
Ill. Reg.
effective
SUBPART N:
ELECTROPLATING
Section 307.2300
General Provisions
a)
Applicability.
1)
This Subpart applies
to any electroplating
operations
in which metal
is electroplated on any
basis material and
to related metal
finishing
operations as set forth
in the various
Subparts,
whether
such operations are conducted
in
conjunction with electroplating,
independently or
as part of some other operation.
2)
Operations similar
to electroplating which are
specifically excepted from coverage of this Subpart
include:
A)
Electrowinning and electrorefining conducted
as a part of nonferrous metal
smelting and
refining
(Subpart V)
B)
Metal surface preparation and conversion
coating conducted
as
a part of coil coating
(Subpart CN)
C)
Metal surface preparation and immersion
plating
or electroless plating conducted
as
a
part of porcelain enameling
(Subpart CO);
and
D)
Electrodeposition of active electrode
materials,
electroimpregnation and
electroforming conducted
as
a part of battery
manufacturing (Subpart CJ).
3)
Metallic platemaking and gravure cylinder
preparation conducted within or
for printing and
publishing facilities,
and continuous strip
electroplating conducted within iron and
steel
manufacturing facilities are exempted
from the
pretreatment standards for existing sources set
forth in this Subpart.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 413.02
(1986),
as amended
at
51 Fed.
79.404

—59—
Reg.
40421, November
7,
1986.
This incorporation
includes
no later amendments
or editions.
c)
Monitoring requirements.
The Board
incorporates by
reference 40 CFR 413.03
(1986).
This incorporation
includes no later
amendments or editions.
d)
Compliance dates.
The Board incorporates by reference
40 CFR 413.01(a)
(1986).
This incorporation includes no
later amendments or editions.
e)
Integrated facilities.
The Board incorporates by
reference
40 CFR 413.04
(1986).
This incorporation
includes no later amendments or editions.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.2301
Electroplating of Common Metals
a)
Applicability.
This Section
applies to discharges
resulting from the process in which
a ferrous
or
nonferrous basis material
is electroplated with copper,
nickel, chromium,
zinc, tin,
lead,
cadmium,
iron,
aluminum or any combination of these.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 413.11
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
1)
The
Board
incorporates by reference 40 CFR 413.14
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2302
Electroplating of Precious Metals
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which
a ferrous
or
nonferrous
basis material
is plated with gold, silver,
iridium, palladium, platinum,
rhodium,
rutheniun or
any
79-405

—60—
combination of these.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 413.21
(1986).
This incorporation
includes
no later amendments or editions.
C)
Existing sources:
1)
The Board incorporates
by
reference
40 CFR 413.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
All
sources are regulated
as existing
sources.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2304
Anodizing
a)
Applicability.
This Section applies to discharges
resulting from the anodizing of
ferrous
or nonferrous
materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 413.41
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 413.44
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2305
Coatings
79-406
—61—
~j
Applicability.
This Section applies to discharges
resulting from the chromating, phosphating
or immersion
plating on ferrous
or nonferrous materials.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 413.51
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 413.54
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11 Ill. Reg.
effective
Section 307.2306
Chemical Etching and Milling
a)
Applicability.
This Section applies
to discharges
resulting from the chemical milling
or etching
of
ferrous
or nonferrous materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 413.61
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing
sources:
1)
The Board incorporates by reference
40 CFR 413.64
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
All
sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
79-407

—62—
Section 307.2307
Electroless Plating
a)
Applicability.
This
Section
applies
to
discharges
resulting from the electroless plating
of
a metallic
layer on
a metallic or nonmetallic substrate.
b)
Specialized
definitions.
The
Board
incorporates
by
reference
40
CFR
413.71
(1986).
This
incorporation
includes no later amendments
or editions.
c)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 413.74
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to a POTW
in violation of
such
standards.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2308
Printed Circuit Boards
a)
Applicability.
This Section applies to discharges
resulting from the manufacture
of printed circuit
boards,
including all manufacturing operations required
or used
to convert an insulating substrate
to
a finished
printed circuit board.
The provisions set forth
in
other Sections of
this Subpart are not applicable
to
the
manufacture of printed circuit boards.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 413.81
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 413.84
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to a POTW in violation of such
standards.
79-408

—63—
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
SUBPART 0:
ORGANIC CHEMICALS MANUFACTURING
Section 307.2402
Processes with Process Water Contact only as
Steam Diluent, Quench or Vent Gas Absorbent
a)
Applicability.
This Section applies to discharges of
process wastewater resulting from the manufacture of
butadiene by any process which includes the oxidative
dehydrogenation of butene.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 414.21
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 414.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after April
25,
1974.
(Source:
Added
at
11
Ill.
Reg.
effective
SUBPART
P:
INORGANIC CHEMICALS MANUFACTURING
Section 307.2500
General Provisions
Compliance dates.
The Board
incorporates by reference 40 CFR
415.01
(1986).
This incorporation includes
no later
amendments
or editions.
(Source:
Added
at
11
Ill.
Reg.
effective
79.409

—64—
Section 307.2501
~luminum Chloride Production
a)
Applicability.
This Section applies
to discharges
resulting from
the production of aluminum chloride.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates
by reference
40 CFP 415.14
(1086).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(I)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation
of such
standards.
d)
New sources:
All
sources are regulated
as existing
sources.
(Source:
Added
at
1.
Iii.
Beg.
effective
)
Section 307.2502
Aluminum Sulfate Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of aluminum sulfate.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFB
415.24
(3.986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation of such
standards.
d)
New sources:
3.)
The Eoard
incorporates by reference
40 CFP 415.26
(1986).
This incorporation includes
no later
amendments
or
editions.
2)
No person subject
to
the pretreatment standards
incorporated
by reference
in
subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a
POTW
in violation of such
79.410

—65—
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after July 24,
1980.
(Source:
Added at
11
Ill. Reg.
,
effective
Section 307.2503
Calcium Carbide Production
a)
Applicability.
This Section applies to discharges
resulting from the production of calcium carbide
in
uncovered furnaces.
b)
Specialized definitions.
None.
C)
Existing
sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 415.36
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of
any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at 11
Ill. Reg.
effective
Section 307.2504
Calcium Chloride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of calcium chloride by the
brine extraction process.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 415.41
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
79-411

—66—
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.46
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2505
Calcium Oxide Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of calcium oxide.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.56
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after July 24,
1980.
(Source:
Added at
11
Ill. Reg.
effective
Section 307.2506
Chlor—alkali Process
(Chlorine and Sodium or
Potassium Hydroxide Production)
a)
Applicability.
This Section applies to discharges
resulting
from the production of chlorine and sodium or
79-412

—67—
potassium hydroxide by the diaphragm cell process or by
the mercury cell process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.61
(1986).
This incorporation
includes no
later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 415.64
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(I) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 415.66
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section
307.2508
Hydrofluoric
Acid
Production
a)
Applicability.
This
Section
applies
to discharges
resulting
from
the production of hydrofluoric acid.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.86
(1986).
This incorporation includes no later
amendments or editions.
79-413

—68—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source:
Added at 11 Ill.
Reg.
effective
)
Section 307.2509
Hydrogen Peroxide Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of hydrogen peroxide by
the electrolytic process or by the oxidation of alkyl
hydroanthraquinones.
b)
Specialized
definitions.
The Board
incorporates by
reference 40 CFR 415.91
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with
the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2511
Potassium Metal Production
a)
Applicability.
This Section applies to discharges
resulting from the production of potassium metal.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR
415.116
(1986).
This
incorporation
includes
no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
79-414

—69—
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source~ Added
at
11 Ill. Reg.
effective
)
Section 307.2512
Potassium Dichromate Production
a)
Applicability.
This Section applies to discharges
resulting from the production of potassium dichromate.
b)
Specialized definitions.
None.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 415.124
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
3.)
The Board incorporates by reference 40 CPR 415.126
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminaritto
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at 11 Ill. Reg.
effective
Section 307.2513
Potassium Sulfate Production
a)
Applicability.
This Section applies
to discharges
resulting
from the production of potassium sulfate.
79-415

—70—
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.136
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.2514
Sodium Bicarbonate Production
a)
Applicability.
This Section applies to discharges
resulting from the production of sodium bicarbonate.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.146
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
July 24,
1980.
(Source:
Added at
11
Ill.
Reg.
79-416

—71—
effective
Section 307.2516
Sodium Chloride Production
a)
Applicability.
This Section applies to discharges
resulting from the production of sodium chloride by the
solution brine—mining process or by the solar
evaporation process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.161
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.166
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to
the pretreatment standards
incorporated
by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility
or
installation
the construction of which
commenced after July 24,
1980.
(Source:
Added at
13. Ill. Reg.
,
effective
)
Section 307.2517
Sodium Dichromate and
Sodium
Sulfate
Production
a)
Applicability.
This Section applies to discharges
resulting from the production of sodium dichromate and
by—product sodium sulfate.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.171
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
79-417

—72—
1)
The Board
incorporates by reference 40 CFR 415.176
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24, 1980.
(Source:
Added
at 11
Ill. Reg.
effective
Section 307.2520
Sodium Sulfite Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of sodium sulfite by
reacting sulfur dioxide with sodium carbonate.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.201
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 415.206
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2522
Titanium Dioxide Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of titanium dioxide by the
79-418

—73—
sulfate process,
the chloride process or the
simultaneous beneficiation—chlorination
(chloride—
ilmenite) process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.221
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.226
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2523
Aluminum Fluoride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of aluminum fluoride.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 415.231
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
These sources shall comply with
the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.2524
Ammonium Chloride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of
ammoniurn chloride by
79-419

—74—
the reaction of anhydrous ammonia with hydrogen chloride
gas or by the recovery process from Solvay process
wastes.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 415.241
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.2527
Borax Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of borax
by the ore mining
process or by the Trona process.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All
sources are regulated
as existing
sources.
(Source:
Added
at
11 Ill. Reg.
effective
)
Section 307.2528
Boric Acid Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of boric
acid from ore—
mined
borax
or from borax produced by the Trona process.
b)
Specialized definitions.
The Board
incorporates by
reference
40
CFR
415.281
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
79-420

—75—
effective
Section 307.2529
Bromine Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of bromine by the brine—
mining process or by the Trona process.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall
comply with the
general and
specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.296
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October 25,
1983.
(Source:
Added
at 11
Ill. Reg.
effective
)
Section 307.2530
Calcium Carbonate Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of calcium carbonate by
the milk of lime process
or by the recovery process from
Solvay process wastes.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 415.301
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
79-421

—76—
Section 307.2531
Calcium Hydroxide Production
a)
Applicability.
This Section applies to dischar~es
resulting from the production of calcium hydroxide by
the lime slaking process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.311
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.316
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POT~in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October •25,
1983.
(Source:
Added at 11
Ill.
Reg.
effective
Section 307.2533
Carbon Monoxide and Byproduct Hydrogen
Production
a)
Applicability.
This Section applies to discharges
resulting from the production of carbon monoxide and by-
product hydrogen by the reforming process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.331
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These
sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at 11
Ill.
Reg.
effective
79-422

—77—
Section 307.2534
Chrome Pigments Production
a)
Applicability.
This Section applies to discharges
resulting from the production of chrome pigments.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.341
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 415.344
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.346
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2535
Chromic Acid Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of chromic acid
in
facilities which also manufacture
sodium dichromate.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
79-423

—78—
1)
The Board
incorporates by reference
40 CFR 415.356
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2536
Copper Salts Production
a)
Applicability.
This Section applies
to discharges
resulting
from the production of copper salts,
including:
1)
Copper sulfate, copper
chloride, copper
iodide and
copper nitrate,
and
2)
Copper carbonate.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 415.361
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 415.364
(1986).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.366
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person
subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
79-424

—79—
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October 25,
1983.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.2538
Ferric Chloride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of ferric chloride from
pickle liquor.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.381
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 415.384
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.386
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2540
Fluorine Production
a.)
Applicability.
This Section applies
to discharges
resulting from the production of fluorine by the liquid
79-425

—80—
hydrofluoric acid electrolysis process.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.401
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference
40 CFR 415.406
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after October
25,
1983.
(Source:
Added at
11
Ill.
Reg.
effective
Section 307.2541
Hydrogen Production
a)
Applicability.
This Section applies to discharges
resulting from the production of hydrogen as
a refinery
by—product.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.411
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2542
Hydrogen Cyanide Production
a)
Applicability.
This Section applies
to discharges
resulting from the production
of hydrogen cyanide by the
Andrussow process.
79-426

—81
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.421
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.426
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 24,
1980.
(Source:
Added
at 11 Ill. Reg.
effective
Section 307.2543
Iodine Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of
iodine.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.431
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415. 436
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
79-427

—82—
facility
or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at 11
Ill. Reg.
effective
Section 307.2544
Lead Monoxide Production
a)
Applicability.
This Section applies to discharges
resulting from the production of lead monoxide.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.441
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 415.444
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.446
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added at
11
Ill.
Reg.
effective
Section 307.2545
Lithium Carbonate Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of lithium carbonate by
the Trona process
or from spodumene ore.
b)
Specialized definitions.
The
Board incorporates by
reference 40 CFR 415.451
(1986).
This incorporation
79-428

—83—
includes
no later amendments or editions.
C)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
All
sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.2547
Nickel Salts Production
a)
Applicability.
This Section applies
to discharges
resulting
from the production of nickel
salts,
including:
1)
Nickel
sulfate, nickel
chloride, nickel nitrate,
and nickel fluoborate,
and
2)
Nickel carbonate.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.471
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 415.474
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.476
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October 25,
1983.
79-429

—84
(Source:
Added at 11
Ill.
Req.
effective
Section 307.2549
Oxygen and Nitrogen Production
a)
Applicability.
This Section applies to discharges
resulting from the production of oxygen and nitrogen by
air liquification.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with
the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2550
Potassium Chloride Production
a)
Applicability.
This Section applies to discharges
resulting from the production of potassium chloride by
the Trona process or by the mining process.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.506
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2551
Potassium Iodide Production
79-430

—85—
a)
Applicability.
This Section applies to discharges
resulting from the production of potassium iodide.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.511
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
g~eral and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
a.t
11
Ill.
Reg.
effective
)
Section 307.2553
Silver Nitrate Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of silver nitrate.
b)
Specialized
definitions.
The Board incorporates by
reference 40 CFR 415.531
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 415.534
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.2554
Sodium Bisulfite Production
a)
Applicability.
This Section applies to discharges
resulting from the production of sodium bisulfite.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.541
(1986).
This incorporation
includes
no later amendments
or editions.
79-431

—86—
c)
Existing sources:
These sources shall comply with
the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 415.546
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after
July
24,
1980.
(Source:
Added
a.t 11
Ill.
Req.
effective
)
Section 307.2555
Sodium Fluoride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of sodium fluoride by the
anhydrous neutralization process or by the silico
fluoride process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.551
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 415.554
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.556
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
79-432

—87—
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill. Reg.
,
effective
)
Section 307.2560
Stannic Oxide Production
a)
Applicability.
This Section applies to discharges
resulting from the production of stannic oxide by the
reaction of tin metal with air
or oxygen.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.601
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference
40 CFR 415.606
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to a POT~in violation of such
standards.
3)
“New source”
means any building, structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added
a.t
11
Ill. Reg.
effective
)
Section 307.2563
Zinc Sulfate Production
a)
Applicability.
This Section applies
to discharges
resulting
from the production of
zinc sulfate.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 415.631
(1986).
This incorporation
includes no later
amendments
or editions.
C)
Existing sources:
These sources shall comply with the
79.433

—88—
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 415.636
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.2564
Cadmium Pigments and Salts Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of cadmium pigments and
salts including cadmium chloride, cadmium nitrate and
cadmium sulfate.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.641
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 415.644
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
I)
The Board
incorporates by reference 40 CFR 415.646
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
79.434

—89—
contaminant
to a POTW
in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
a.t 11
Ill.
Reg.
effective
Section 307.2565
Cobalt Salts Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of cobalt salts.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.651
(1986).
This incorporation
includes no later
amendments or
editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 415.654
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 415.656
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.2566
Sodium Chlorate Production
a)
Applicability.
This Section
applies to discharges
resulting from the production of sodium chlorate.
79-435

—90—
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 415.661
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 415.666
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
25,
1983.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2567
Zinc Chloride Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of
zinc chloride.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 415.671
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 415.674
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 415.676
(1986).
This incorporation includes
no later
amendments or editions.
79-436

—91
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
25,
1983.
(Source:
Added at 11
Ill. Reg.
effective
)
SUBPART
R:
SOAP AND DETERGENTS
Section 307.2701
Soap Manufacturing by Batch Kettle
a)
Applicability.
This Section applies
to discharges
resulting from operations in which neat soap is produced
through saponification of animal
and vegetable fats and
oils by boiling
in kettles.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.11
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 417.14
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 417.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
26,
1973.
79-437

—92—
(Source:
Added at 11
Ill.
Reg.
effective
Section 307.2702
Fatty Acid Manufacturing by Fat Splitting
a)
Applicability.
This Section applies to discharges
resulting from the splitting of fats
to fatty acids by
hydrolysis and the subsequent processing of
the fatty
acids
(e.g.,
refining and hydrogenation)
to produce a
suitable feed
material
for
manufacture
of
soap
by
fatty
acid neutralization.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.21
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 417.24
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 417.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced
after
December
26,
1973.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.2703
Soap Manufacturing by Fatty Acid
Neutralization
a)
Applicability.
This Section applies to discharges
resulting from the manufacturing of
neat soap by
neutralizing refined fatty acids with
an alkaline
79.438

—93—
material
in approximately stoichiemetric amounts
in
batch or continuous operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.31
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 417.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 417.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after December 26,
1973.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.2704
Glycerine Concentration
a)
Applicability.
This Section applies
to discharges
resulting from the concentration of sweet water
from
saponification or fat splitting
to approximately 60
to
80 percent crude glycerine content.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.41
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 417.44
(1986).
This incorporation includes no later
amendments or editions.
79.439

—94—
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference
40 CFR 417.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at 11 Ill.
Reg.
effective
Section 307.2705
Glycerine Distillation
a)
Applicability.
This Section applies
to discharges
resulting from the production of finished glycerine of
various grades
(e.g.,
tJSP)
through concentration from
crude glycerine by means of distillation.
b)
Specialized definitions.
The
Bo.ard incorporates by
reference 40 CFR 417.51
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 417.54
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
3.)
The Board
incorporates by reference
40 CFR 417.56
(1986).
This incorporation includes no later
amendments or editions.
79-440

—95—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December 26,
1973.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2706
Manufacture of Soap Flakes and Powders
a)
Applicability.
This Section applies
to discharges
resulting from all operations associated with the
manufacture of soap flakes
and powders, commencing with
the drying
of the neat soap
to and including packaging
of the finished flakes and powders.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.61
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 417.64
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POT~~Jin violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 417.66
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of
any
contaminant to
a POTW
in violation of
such
standards.
3)
“New source”
means any building, structure,
facility or
installation
the construction of which
commenced after December
26,
1973.
79-441

—96—
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.2707
Manufacture
of Bar
Soaps
a)
Applicability.
This Section applies to discharges
resulting from all operations associated with conversion
of neat soap to finished bar soaps,
including drying,
milling,
plodding, stamping and packaging.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.71
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 417.74
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
Cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 417.76
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.2708
Manufacture of Liquid Soaps
a)
Applicability.
This Section applies
to discharges
resulting from the blending
of ingredients employed
in
the manufacture of liquid soaps and the packaging
of
the
finished products.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.81
(1986).
This incorporation
79-442

—97—
includes no later amendments
or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 417.84
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 417.86
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December 26,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2709
Oleum Sulfonation and Sulfation
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of sulfonic acid and
sulfuric acid esters by means of sulfonation and
sulfatiori of raw materials,
including but not limited
to
petroleum derived alkyls, employing oleum
in
either
continuous or batch processes.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.91
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 417.94
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
79-443

—98—
cause,
threaten or
allow the discharge of any
contaminant to a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 417.96
tl986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2710
Air—Sulfur Trioxide Sulfation and Sulfonation
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of sulfonic acid
and
sulfuric acid esters by means of sulfation and
sulfonation employing air and sulfur trioxide
in either
continuous or batch processes.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.101
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 417.104
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 417.106
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
79-444

—99—
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2711
Sulfur Trioxide Solvent and Vacuum Sulfonation
a)
Applicability.
This Section applies
to discharges
resulting from the operations
in which undiluted
sulfur
trioxide and organic reactant are fed through a mixing
nozzle into a vacuum reactor where the sulfonation of
the organic reactant takes place.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.111
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 417.114
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 417.116
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at
11
Ill.
Rey.
effective
79-445

—100—
Section 307.2712
Sulfamic Acid Sulfation
a)
Applicability.
This Section applies to discharges
resulting from operations
in which sulfatnic acid
is
employed as the sulfating agent.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.121
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference 40 CFR 417.124
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to
a POTW
in violation
of
such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 417.126
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation
the construction
of which
commenced after December
26,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section
307.2713
Chlorosulfonic Acid Sulfation
a)
Applicability.
This Section applies
to discharges
resulting
from sulfation
of alcohols, alkylphenols and
alcohol ethoxylates utilizing chlorosulfonic
acid as
the
sulfating agent.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.131
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
79-446

—101—
1)
The Board
incorporates by reference
40 CFR 417.134
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in
subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by reference 40 CFR 417.136
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility
or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2714
Neutralization of Sulfuric Acid Esters and
Sulfonic Acids
a)
Applicability.
This Section applies
to discharges
resulting from the continuous
or batch neutralization of
sulfated and sulfonated alkylbenzenes, alcohols and
other materials to convert them to neutral salts.
b)
Specialized
definitions.
The Board
incorporates by
reference 40 CFR 417.141
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 417.144
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to
a POTW in violation of
such
standards.
79-447

—102—
d)
New sources:
1)
The Board incorporates by reference 40 CFR 417.146
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation
of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.2715
Manufacture of Spray Dried Detergents
a)
Applicability.
This Section applies
to discharges
resulting from all operations associated with
the
manufacture
of spray dried detergents,
including but not
limited
to assembly and storage of
raw materials,
crutching,
spray drying,
blending
(including tumble
spraying
or
additives)
and packaging.
b)
Specialized
definitions.
The Board incorporates by
reference 40 CFR 417.151
(1986).
This incorporation
includes no
later amendments or editions.
c)
Existing sources:
These sources shall comply with
the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board
incorporates by reference
40 CFR 417.156
(1986).
This incorporation includes
no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility
or installation the construction
of which
commenced after December
26,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
79.448

—103—
Section 307.2716
Manufacture of Liquid Detergents
a)
Applicability.
This Section applies
to discharges
resulting from all operations associated with the
manufacture of liquid detergents, commencing with the
blending of
ingredients, to and
including bottling or
packaging finished products.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.161
(1986).
This incorporation
includes_no_later amendments or editions.
C)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 417.166
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after December
26,
1973.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.2717
Manufacturing
of Detergents by Dry Blending
a)
Applicability.
This Section applies
to discharges
resulting from operations associated with the
manufacture
of detergents by means of the blending of
dry ingredients, including, but not limited
to, blending
and subsequent packaging.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.171
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing
sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
79.449

—104—
1)
The Board
incorporates by reference
40 CFR 417.176
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
26,
1973.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.2718
Manufacture of Drum Dried Detergents
a)
Applicability.
This Section applies to discharges
resulting
from operations associated with the
manufacture of detergents by drum drying,
including,
but
not limited
to, drying of formulations on heated drums
or
rollers, conversion of dried detergents
to powders
or
flakes and packaging
of finished products.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 417.181
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 417.186
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after December
26, 1973.
(Source:
Added
a.t
11
Ill.
Reg.
effective
Section 307.2719
Manufacture
of Detergent Bars and Cakes
79-450

—105—
a)
Applicability.
This Section applies
to discharges
resulting from operations associated with the
manufacture of detergent bars and cakes,
including,
but
not limited
to,
drying, milling, plodding, stamping and
packaging.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 417.191
(1986).
This incorporation
includes no later amendments
or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 417.194
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1) shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 417.196
(1986).
This incorporation includes
no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten
or
allow
the
discharge
of
any
contaminant
to
a POTW
in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced after
December
26, 1973.
(Source:
Added
at 11 Iii. Req.
effective
SUBPART
5:
FERTILIZER MANUFACTURING
Section 307.2801
Phosphate
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of sulfuric acid by
sulfur
burning, wet process phosphoric
acid, normal
superphosphate,
triple superphosphate and ammonium
phosphate.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 418.11
(1986).
This incorporation
79.45
1

—106—
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with
the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40
~rt
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility
or
installation the construction of which
commenced after December
7,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.2802
Ammonia
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of ammonia.
Discharges
attributable to shipping losses and cooling
tower
blowdown are excluded.
b)
~pecialized definitions.
The Board
incorporates by
reference 40 CFR 418.21
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
These
sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference
40 CFR 418.26
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
79.452

—107—
commenced after
December
7,
1973.
(Source:
Added
at
11
Ill. Req.
effective
Section 307.2803
Urea
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of urea.
Discharges
attributable to shipping losses
and precipitation runoff
from outside the battery limits of the urea
manufacturing operations and cooling
tower blowdown are
excluded
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 418.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 418.36
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced
after
December
7,
1973.
(Source:
Added at 11
Ill.
Reg.
effective
Section 307.2804
Ammoniuin Nitrate
a)
Applicability.
This Section applies to discharges
resulting from the maunfacture of
amnionium nitrate.
b)
These sources
shall comply with
the general
and
specific
pretreatment requirements of
Subpart
B.
(Source:
Added at
11
Ill.
Reg.
effective
Section 307.2805
Nitric Acid
79-453

—108—
a)
Applicability.
This Section applies
to discharges
resulting from production
of nitric acid
in
concentrations up to
68 percent.
Discharges from
shipping losses are excluded.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 418.51
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 418.56
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced
after December
7,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.2806
Ammonium Sulfate Production
a)
Applicability.
This Section applies to discharges
resulting
from the production of ammonium sulfate by the
synthetic process or by coke oven byproduct recovery.
This Section does not apply to
aminonium sulfate produced
as
a byproduct of caprolactam production.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 418.61
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 418.66
(1986).
This incorporation includes
no
later
amendments
or editions.
79-454

—109—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
~j
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
7,
1974.
(Source:
Added
at
11
Ill.
Reg.
,
effective
)
Section 307.2807
Mixed and Blend Fertilizer Production
a)
Applicability.
This Section applies
to discharges
resulting from the production of mixed
fertilizer
and
blend fertilizer.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 418.71
(1986).
This incorporation
includes
no later amendments
or editions.
C)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 418.76
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
7,
1974.
(Source:
Added
at
11
Ill.
Reg.
effective
)
SUBPART
T:
PETROLEUM REFINING
Section 307.2901
Topping
a)
Applicability.
This Section applies
to aiscnarges
from
any facility that produces petroleum products by the use
of topping and
catalytic reforming,
whether
or
not
the
facility includes any other
process
in addition
to
79.455

—110—
topping and catalytic reforming.
This Section does not
apply to facilities that include thermal processes
(coking, vis—breaking, etc.)
or
catalytic cracking.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 419.11
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 419.15
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 419.17
(1986).
This incorporation includes
no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation
of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
21, 1979.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2902
Cracking
a)
Applicability.
This Section applies
to discharges from
any facility that produces petroleum products by the use
of topping and cracking, whether
or not the facility
includes any process
in addition to topping
and
cracking.
This Section does not apply,
however,
to
facilities that include the processes specified
in
Sections 307.2903,
307.2904
and 307.2905.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 419.21
(1986).
This incorporation
includes
no
later
amendments
or
editions.
c)
Existing sources:
79-456

—111—
U
The Board incorporates by reference 40 CFR 419.25
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 419.27
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after December
21,
1979.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.2903
Petrochemical
a)
Applicability.
This Section applies to discharges from
any facility that produces petroleum products by the
use
of topping, cracking and petrochemical operations
whether
or not the facility includes any process
in
addition
to topping,
cracking and petrochemical
operations.
This Section does not apply, however,
to
facilities that include
the processes specified
in
Sections 307.2904
of 307.2905.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 419.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 419.35
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or
allow the discharge of any
79.457

—112—
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 419.37
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
~j
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
21,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.2904
Lube
a)
Applicability.
This Section applies
to discharges from
any facility that produces petroleum products by the use
of topping, cracking and lube oil manufacturing
processes, whether
or not the facility includes any
process
in addition
to topping, cracking
and lube oil
manufacturing processes.
The Section does not apply,
however, to facilities that include the processes
specified
in Sections 307.2903 and 307.2905.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 419.41
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 419.45
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 419.47
(1986).
This incorporation includes
no later
amendments or editions.
79.458

—113—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after December
21,
1979.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.2905
Integrated
a)
Applicability.
This Section applies
to discharges from
any
facility
that
produces
petroleum
products
by
the
use
of topping, cracking,
lube oil manufacturing processes
and petrochemical operations, whether or
not the
facility includes any process
in addition
to
topping,
cracking, lube oil manufacturing processes and
petrochemical operations.
b)
Specialized
definitions.
The
Board
incorporates by
reference 40 CFR 419.51
(1986).
This incorporation
includes
no later amendments
or editions.
C)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 419.55
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates
by
reference 40 CFR 419.57
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of
any
contaminant to
a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
79.459

—114—
commenced after December
21,
1979.
(Source:
Added
at
11
Ill. Reg.
effective
SUBPART
U:
IRON AND STEEL MANUFACTURING
Section 307.3000
General Provisions
a)
Applicability.
1)
This Subpart applies
to the introduction of
pollutants into a POTW resulting from production
operations in the iron and steel category.
2)
The Board incorporates by reference 40 CFR
420.01(b)
(1986).
This incorporation includes no
later
amendments or editions.
b)
General definitions.
The Board incorporates by
reference 40 CFR 420.02
(1986).
This incorporation
includes no
later amendments or
editions.
C)
Compliance dates.
The Board
incorporates by reference
40 CFR 420.05
(1986).
This incorporation includes no
later amendments
or editions.
d)
Calculation
of pretreatment standards.
The Board
incorporates by reference
40 CFR 420.04
(1986).
This
incorporation includes
no later amendments or
editions.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.3001
Cokemaking
a)
Applicability.
This Section applies
to discharges
resulting from byproduct and beehive cokemaking
operations.
b)
Specialized definitions.
The Board
incorporates by
reference
40
CFR
420.11
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 420.15
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standarcis
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
79-460

—115—
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 420.16
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after January
7,
1981.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.3002
Sintering
a)
Applicability.
This Section applies
to discharges
resulting from sintering operations conducted by the
heating
of iron bearing wastes (mill scale and dust from
blast furnaces and steelmaking
furnaces)
together
with
fine iron ore, limestone and coke fines
in
an
ignition
furnace
to produce an agglomerate
for charging
to the
blast furnace.
b)
Specialized definitions.
None.
C)
Existing sources:
1)
The Board
incorporates
by reference 40 CFR 420.25
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New
sources:
U
The Board incorporates by reference 40 CFR 420.26
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
79-461

—116—
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January
7,
1981.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.3003
Ironmaking
a)
Applicability.
This Section applies
to discharges
resulting from ironmaking operations
in which
iron ore
is reduced
to molten iron in
a blast furnace.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 420.31
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 420.35
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of
such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 420.36
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or
installation the construction of which
commenced after January
7,
1981.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3004
Steelmaking
a)
Applicability.
This Section applies
to discharges
79-462

—117—
resulting from steelmaking operations conducted
in basic
oxygen, open hearth or electric arc furnaces.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 420.41
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing
sources:
U
The Board incorporates
by
reference 40 CFR 420.45
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 420.46
(1986).
This incorporation includes no later
amendments
or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated
by
reference
in
subsection
(1)
shall
cause,
threaten
or
allow
the
discharge
of
any
contaminant
to
a POTI~in violation
of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January
7,
1981.
(Source:
Added at
11 Ill. Reg.
effective
)
Section 307.3005
Vacuum Degassing
a)
Applicability.
This Section applies to discharges
resulting from vacuum degassing operations conducted by
applying
a vacuum
to molten steel.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 420.55
(1986).
This incorporation includes no
later
amendments or
editions.
2)
No person
subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-463

—118—
cause,
threaten or allow
the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
U
The Board
incorporates
by
reference 40 CFR 420.56
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POT~IJ in violation
of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or
installation the construction of which
commenced after January
7,
1981.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.3006
Continuous Casting
a)
Applicability.
This Section applies
to discharges
resulting
from the continuous casting
of molten steel
into intermediate or semi—finished
steel products
through water cooled molds.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 420.65
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 420.66
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person
subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge
of any
contaminant to
a POTW
in violation of
such
79-464

—119—
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January
7,
1981.
(Source:
Added at
11
Ill.
Reg.
effective
Section 307.3007
Hot Forming
a)
Applicability.
This Section applies
to discharges
resulting
from
hot forming operations conducted
in
primary,
section, flat,
and pipe and tube mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 420.71
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 420.75
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
These sources shall comply with the
standards for existing sources.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.3008
Salt Bath Descaling
a)
Applicability.
This Section applies
to discharges
resulting from oxidizing
or reducing
salt bath descaling
operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 420.81
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference 40 CFR 420.85
(1986).
This incorporation includes
no later
amendments or
editions.
2
No person subject
to the pretreatment standards
79-465

—120—
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 420.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge
of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 7,
1981.
(Source:
Added
at
11
Ill.
Req.
,
effective
Section 307.3009
Acid Pickling
a)
Applicability.
This Section applies
to discharges
resulting from sulfuric acid, hydrochloric
acid or
combination acid pickling operations
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 420.91
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference 40 CFR 420.95
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 420.96
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-466

—121—
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after January 7,
1981.
(Source:
Added at
11 Ill.
Reg.
effective
)
Section 307.3010
Cold Forming
a)
Applicability.
This Section applies
to discharges
resulting from cold rolling and cold working
pipe and
tube operations in which unheated steel
is passed
through rolls or otherwise processed
to
reduce
its
thickness,
to produce
a smooth surface
or
to develop
controlled
mechanical
properties
in
the
steel.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 420.101
(1986).
This incorporation
includes
no later
amendments or
editions.
C)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 420.105
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The
Board
incorporates
by
reference
40
CFR
420.106
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause,
threaten
or
allow
the
discharge
of
any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction
of which
commenced after
January
7,
1981.
(Source:
Added
at 11
Ill.
Reg.
,
effective
79-467

—122—
Section 307.3011
Alkaline Cleaning
a)
Applicability.
This Section applies
to discharges
resulting from operations
in which steel
or steel
products are immersed
in alkaline cleaning baths to
remove mineral
or animal fats or oils from the steel,
and those rinse operations which follow such immersion.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 420.111
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing
sources:
These
sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3012
Hot Coating
a)
Applicability.
This Section applies
to discharges
resulting
from operations
in which
steel
is coated with
zinc,
terne metal or other
metals by the hot dip
process, and those rinsing operations associated with
that process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 420.121
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 420.125
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 420.126
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
79.468

—123—
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a
POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
January 7, 1981.
(Source:
Added
at 11
Ill.
Reg.
effective
)
SUBPART V:
NONFERROUS METALS MANUFACTURING
Section 307.3100
General Provisions
a)
Applicability.
This Subpart applies to any facility
producing primary metals from ore concentrates
or
recovering
secondary metals from recycle wastes which
introduces or may introduce pollutants into a POTW.
This Subpart applies only to alloying
or casting
of hot
metal directly from the nonferrous metals manufacturing
process without cooling.
Remelting followed by alloying
or
cooling
is included
in the aluminum forming,
nonferrous metals forming or metal molding and casting
categories.
c)
Monitoring requirements.
The Board
incorporates by
reference 40 CFR 421.3
(1986).
This incorporation
includes no later
amendments or
editions.
d)
Compliance dates.
The Board
incorporates by reference
40 CFR 421.4
(1986).
This incorporation includes no
later amendments
or editions.
(Source:
Added
at
11 111.
Reg.
effective
Section 307.3101
Bauxite Refining
a)
Applicability.
This Section applies
to discharges
resulting from the refining
of bauxite
to alumina by the
Bayer process
or by the combination process.
b)
Specialized definitions.
The Board incorporates by
reference
40
CFR
421.11
(1986).
This
incorporation
includes no later
amendments or
editions.
c)
Existing
sources:
These sources shall
comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
79-469

—124—
1)
The Board
incorporates by reference 40 CFR 421.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
Cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation
of such
standards.
3)
“New source”
means any building, structure,
facility or installation the construction
of which
commenced after June
27,
1984.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.3102
Primary Aluminum Smelting
a)
Applicability.
This Section applies
to discharges
resulting from the production of aluminum from alumina
by the Hall—Herloult process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.21
(1986).
This incorporation
includes no later amendments
or editions.
C)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.26
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after February 17,
1983.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3103
Secondary Aluminum Smelting
a)
Applicability.
This Section applies
to discharges
resulting from the
recovery, processing
and remelting
of
79-470

—125—
aluminum scrap
to produce metallic aluminum alloys.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.31
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 421.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at
11 Ill. Reg.
effective
Section 307.3104
Primary Copper Smelting
a)
Applicability.
This Section applies to discharges
resulting from the primary smelting of copper from ore
or ore concentrates.
Primary copper
smelting
includes,
but
is not limited
to,
roasting, converting,
leaching
if
preceded by
a pyrometallurgical
step, slag granulation
and dumping,
fire refining and
the casting
of products
from these operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.41
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
79-471

—126—
d)
New sources:
1)
The Board incorporates
by
reference 40 CFR 421.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3105
Primary Electrolytic Copper Refining
a)
Applicability.
This Section applies to discharges
resulting from the electrolytic refining
of primary
copper,
including,
but not limited
to, anode casting
performed
at refineries which
are not located on—site
with
a smelter, product casting and by—product recovery.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.51
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New
sources:
U
The Board
incorporates by reference 40 CFR 421.56
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation
the construction of which
commenced after
February 17,
1983.
(Source:
Added
at 11
Ill.
Reg.
effective
79-472

—127—
Section 307.3106
Secondary Copper
a)
Applicability.
This Section applies
to discharges
resulting from the recovery, processing
and remelting
of
new and used copper scrap and residues
to produce copper
metal
and copper
alloys;
but does not apply to
continuous rod casting.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.61
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing
sources:
1)
The Board incorporates by reference
40 CFR 421.65
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 ~rR 421.66
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after
February 17,
1983.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.3107
Primary Lead
a)
Applicability.
This Section applies
to discharges
resulting from
the production of lead at primary lead
smelters and refineries.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.71
(1986).
This incorporation
includes no
later amendments
or editions.
79.473

—128—
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 421.75
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 421.76
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3108
Primary Zinc
a)
Applicability.
This Section applies to discharges
resulting from the production of zinc by either
electrolytic
or pyrolytic means.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.81
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 421.85
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POT~in violation of
such
standards.
d)
New sources:
79.474

—129—
1)
The Board
incorporates by reference
40 CFR 421.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at
11 Ill.
Req.
effective
Section 307.3109
Metallurgical Acid Plants
a)
Applicability.
This Section applies to discharges
resulting from or associated with the manufacture of by-
product sulfuric acid at primary smelters, primary
copper
smelters, primary zinc facilities, primary lead
facilities
or primary molybdenum facilities,
including
associated
air pollution control
or gas—conditioning
systems
for sulfur
dioxide off—gases from
pyrometallurgical operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.91
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 421.95
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 421.96
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
79.475

—130—
contaminant
to a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at 11
Ill.
Req.
effective
)
Section 307.3110
Primary Tungsten
a)
Applicability.
This Section applies to discharges
resulting from the production of tungsten at primary
tungsten facilities.
b)
Specialized
definitions.
The Board
incorporates by
reference 40 CFR 421.101
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing
sources:
U
The Board
incorporates by reference
40 CFR 421.105
(1986).
This incorporation includes no later
amendments or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference
40 CFR 421.106
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after February 17,
1983.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3111
Primary Columbium—Tantalum
a)
Applicability.
This Section applies
to discharges
79.476

—131—
resulting from the production of
coluinbium or tantalum
by primary columbium—tantalum facilities.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.111
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates
by
reference 40 CFR 421.115
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 421.116
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after
February 17, 1983.
(Source:
Added at 11
Ill.
Req.
effective
)
Section 307.3112
Secondary Silver
a)
Applicability.
This Section applies
to discharges
resulting from the production of silver
from secondary
silver facilities processing photographic and
nonphotographic raw materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.121
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 421.125
(1986).
This incorporation includes no later
amendments
or editions.
79-477

—132—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
Cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference 40 CFR 421.126
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 17,
1983.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.3113
Secondary Lead
a)
Applicability.
This Section applies to discharges
resulting from the production of lead by secondary lead
facilities.
b)
Specialized
definitions.
The
Board
incorporates by
reference 40 CFR 421.131
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 421.135
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.136
(1986).
This incorporation includes no later
amendments
or editions.
79-478

—133—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
Cause,
threaten or allow
the discharge of any
contaminant to
a POTW
in violation of such
standards.
.~J
“New
source”
means
any
building,
structure,
facility or
installation
the construction of which
commenced after
February 17,
1983.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3114
Primary Antimony
a)
Applicability.
This Section applies to discharges
resulting from the production of antimony at primary
antimony facilities.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.141
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
These
sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New
sources:
1)
The Board
incorporates by reference 40 CFR 421.146
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after
June 27,
1984.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.3115
Primary Beryllium
a)
Applicability.
This Section applies
to discharges
resulting from the production of beryllium by primary
beryllium facilities processing beryllium ore
concentrates or beryllium hydroxide raw materials.
b)
Specialized definitions.
The Board
incorporates by
79-479

—134—
reference 40 CFR 421.151
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 421.156
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge
of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3116
Primary and Secondary Germanium and Gallium
a)
Applicability.
This Section applies
to discharges
resulting from the production of germanium or gallium
from primary or secondary germanium or gallium
facilities.
b)
Specialized
definitions.
The
Board
incorporates by
reference
40
CFR
421.181
(1986).
This
incorporation
includes no later amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 421.185
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of
such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.186
(1986).
This incorporation includes no later
amendments or editions.
79-480

—135—
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
3
“New source” means any building, structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added at 11
Ill. Reg.
effective
)
Section 307.3117
Secondary Indium
a)
Applicability.
This Section applies
to discharges
resulting from the production of
indium at secondary
indium facilities processing
spent electrolyte solutions
and scrap indium raw materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.191
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 421.195
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New
sources:
1)
The Board
incorporates by reference 40 CFR 421.196
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Req.
,
79-481

—136—
effective
Section 307.3118
Secondary Mercury
a)
Applicability.
This Section applies to discharges
resulting from
the production of mercury from secondary
mercury facilities processing recycled mercuric oxide
batteries and other mercury containing scrap raw
materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.201
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 421.206
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3119
Primary Molybdenum and Rhenium
a)
Applicability.
This Section applies
to discharges
resulting from the production of molybdenum and rhenium
facilities.
b)
Specialized
definitions.
The Board incorporates by
reference 40 CFR 421.211
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing
sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board
incorporates by reference
40 CFR 421.216
79-482

—137—
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.3120
Secondary Molybdenum and Vanadium
a)
Applicability.
This Section applies to discharges
resulting from the production of molybdenum or vanadium
by
secondary
molybdenum
or vanadium facilities.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.221
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
These sources shall comply with the
general
and
specific
pretreatment
requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 421.226
(1986).
This incorporation includes no later
amendments or editions.
2)
No person
subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building, structure,
facility or installation the construction of which
commenced
after June
27,
1984.
(Source:
Added
at
11
Ill. Req.
effective
)
Section 307.3121
Primary Nickel
and Cobalt
a)
Applicability.
This Section applies to discharges
resulting
from the production of nickel
or cobalt by
primary nickel or cobalt facilities processing ore
79-483

—138—
concentrate raw materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.131
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 421.236
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after June 27,
1984.
(Source:
Added
at 11 111.
Req.
effective
)
Section 307.3122
Secondary Nickel
a)
Applicability.
This Section applies
to discharges
resulting from the production of nickel by secondary
nickel facilities processing
slag,
spent acids or scrap
metal
raw materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.241
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 421.245
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
79-484

—139—
1)
The Board incorporates by reference
40 CFR 421.246
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after June 27,
1984.
(Source:
Added at 11
Ill.
Reg.
effective
Section
307.3123
Primary
Precious Metals and Mercury
a)
Applicability.
This Section applies
to discharges
resulting from the production of gold,
silver
or mercury
by primary precious metals and mercury facilities.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 421.251
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 421.256
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.3124
Secondary Precious Metals
a)
Applicability.
This Section applies
to discharges
resulting from the production of precious metals
at
79-485

—140—
secondary precious metals facilities.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.261
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference 40 CFR 421.265
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 421.266
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after June
27,
1984.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.3125
Primary Rare Earth Metals
a)
Applicability.
This Section applies to discharges
resulting
from
the
production
of rare earth metals and
mischmetal by primary rare earth metals facilities
processing rare earth metal
oxides, chlorides or
fluorides.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.271
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 421.275
(1986).
This incorporation includes
no later
amendments or editions.
79.486

—141—
~
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 421.276
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
KNew source” means any building, structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added at 11 Ill. Req.
effective
Section 307.3126
Secondary Tantalum
a)
Applicability.
This Section applies
to discharges
resulting
from
the
production
of tantalum at secondary
tantalum
facilities.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.281
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 421.286
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
79-487

—142—
commenced after June 27,
1984.
(Source:
Added at
11
Ill. Reg.
effective
Section 307.3127
Secondary Tin
a)
Applicability.
This Section applies to discharges
resulting
from the production of tin at secondary tin
facilities utilizing either pyrometallurgical
or
hydrometallurgical processes
to recover
tin from
secondary materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 421.291
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 421.295
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 421.296
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3128
Primary and Secondary Titanium
a)
Applicability.
This Section applies to discharges
resulting from the production of
titanium at primary or
secondary titanium facilities.
Facilities which
practice only vacuum distillation for
sponge
79-488

—143—
purification and which do not practice electrolytic
recovery of magnesium are exempt from regulations.
All
other primary and secondary titanium facilities are
covered by these regulations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.301
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CPR 421.305
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 421.306
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.3129
Secondary Tungsten and Cobalt
a)
Applicability.
This Section applies
to discharges
resulting from the production of
tungsten
or cobalt at
secondary
tungtsen
or
cobalt
facilities
processing
tungsten or or
tungsten carbide raw materials.
b)
Specialized definitions.
The Board
incorporates by
reference
40
CFR
421.311
(1986).
This
incorporation
includes
no later
amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 421.315
79-489

—144—
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.316
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3130
Secondary Uranium
a)
Applicability.
This Section applies
to discharges
resulting
from the production of uranium
(including
depleted uranium) by secondary uranium facilities.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.321
(1986).
This incorporation
includes
no
later
amendments
or
editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 421.326
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
79.490

—145—
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after June
27,
1984.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3131
Primary Zirconium and Hafnium
a)
Applicability.
This Section applies to discharges
resulting from the production of
zirconium or hafnium at
primary zirconium or hafnium facilities.
There are two
levels of pretreatment standards for existing
and new
sources.
Facilities which produce
zirconium or
zirconium/nickel alloys only by magnesium reduction of
zirconium dioxide
are subject only to the Subpart B
provisions.
All other
facilities are subject to this
Section.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 421.331
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates
by
reference 40 CFR 421.336
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after June 27,
1984.
(Source:
Added
at
11
Ill. Reg.
effective
SUBPART
X:
STEAM ELECTRIC POWER GENERATING
Section 307.3301
Steam Electric Power Generating
a)
Applicability.
This Section applies
to discharges
resulting from operation of
a generating
unit by an
establishment engaged primarily in the generation
of
electricity for distribution and sale which results
79.49 1

—146—
primarily from a process utilizing fossil—type fuel
(coal, oil or
gas)
or nuclear fuel
in conjunction with
with a thermal cycle employing the steam water system
as
the thermodynamic medium.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 423.11
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 423.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 423.17
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
14,
1980.
(Source:
Added
at 11
Ill.
Reg.
effective
SUBPART
Y:
FERROALLOY MANUFACTURING
Section 307.3401
Open Electric Furnaces With Wet Air Pollution
Control Devices
a)
Applicability.
This Section applies
to discharges
resulting from the smelting of ferroalloys
in open
electric
furnaces with wet air pollution control
devices.
This subcategory includes those electric
furnaces
of such construction or configuration that the
furnace off—gases are burned
above
the
furnace charge
level by air drawn
into
the system.
After combustion
the gases are cleaned
in
a wet air pollution control
device,
such as
a scrubber,
an electrostatic
79.492

—147—
precipitator with water
or other aqueous s~rays,etc.
The provisions of the Section are not applicable
to
noncontact cooling water
or
to those electric furnaces
which
are
covered,
closed,
sealed
or
semi—covered
and
in
which the furnace off—yases are not burned prior
to
collection (regulated
in Section 301.3402).
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 424.11
(1986).
This incorporation
includes no later amendments
or editions.
C)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates
by
reference
40 CFR 424.15
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
18,
1973.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.3402
Covered Electric Furnaces and Other Smelting
Operations with Wet Air Pollution Control
Devices
a)
Applicability.
This Section applies to discharges
resulting from the smelting of
ferroalloys
in covered
electric furnaces or other smelting operations, not
elsewhere_included
in this Subpart, with wet air
pollution control devices.
This subcategory includes
those electric furnaces of such construction or
configuration
(known
as
covered,
closed,
sealed,
semi—
covered
or
semi—closed
furnaces)
that
the
furnace
off—
gases
are
not
burned prior
to collection
and cleaning,
and which off—yases are cleaned after collection
in
a
wet air pollution control device such as
a scrubber,
“wet”
baghouse, etc.
This subcategory also includes
those non—electric furnace smelting operations,
such as
exothermic
(i.e.,
aluminothermic
or silicothermic)
smelting, ferromanganese refining,
etc.,
where
these
are
controlled
for
air pollution by wet air pollution
79.493

—148—
control devices.
This subcategory does not include
noncontact cooling water or
those furnaces which utilize
dry dust collection techniques,
such as dry baghouses.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 424.21
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 424.26
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
18,
1973.
(Source:
Added at 11 Ill.
Reg.
effective
)
Section 307.3403
Slag Processing
a)
Applicability.
This Section applies to discharges
resulting from slagprocessing in which:
1)
The residual metal values
in the furnace slag
are
recovered via concentration for
return
to the
furnace;
or
2)
The slag
is “shotted”
for further use.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 424.31
(1986).
This incorporation
includes no later
amendments or
editions.
C)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 424.36
(1986).
This incorporation includes no later
79-494

—149—
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or
installation the construction of which
commenced after October
18,
1973.
(Source:
Added at 11
Ill. Reg.
effective
)
Section 307.3404
Covered Calcium Carbide Furnaces With Wet Air
Pollution Control Devices
a)
Applicability.
This Section applies to discharges
resulting from the production of calcium carbide
in
covered electric furnaces which use wet air pollution
control devices.
This subcategory includes those
electric furnaces of such construction or configuration
(known as covered, closed, sealed, semi—covered or
semi—
closed furnaces)
that the furnace off—gases are not
burned prior
to collection and cleaning, and which off—
gases are cleaned after collection
in
a wet air
pollution control device such as a scrubber,
“wet”
baghouse, etc.
This subcategory does not include
noncontact Cooling water
or
those
furnaces which utilize
dry dust collection techniques,
such as dry baghouses.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 424.11
(1986).
This incorporation
includes no later
amendments
or editions.
C)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3405
Other
Calcium Carbide
Furnaces
a)
Applicability.
This Section applies to discharges
resulting from the production
of calcium carbide
in
those covered
furnaces which do not utilize wet air
pollution control methods.
Covered calcium carbide
furnaces using wet air pollution control devices are
regulated
in Section 307.3404.
Open
(uncovered) calcium
79.495

—150—
carbide furnaces are regulated
in Subpart
P,
Inorganic
Chemicals Manufacturing.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 424.51
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at 11 Ill.
Reg.
,
effective
)
Section 307.3406
Electrolytic Manganese Products
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of electrolytic manganese
products such as electrolytic manganese metal
or
electrolytic manganese dioxide.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 424.61
(1986).
This incorporation
includes no
later amendments
or editions.
C)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3407
Electrolytic Chromium
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of chromium metal by the
electrolytic process.
It does not apply to
the
manufacture
of chromium metal
by aluminothermic or other
methods.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 424.71
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing
sources:
These sources shall
comply with the
general
and specific pretreatment requirements of
Subpart
B.
79-496

—151—
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at 11
Ill.
Req.
,
effective
SUBPART
Z:
LEATHER TANNING AND FINISHING
Section 307.3500
General Provisions
a)
Applicability.
This Subpart applies
to any leather
tanning and finishing facility which introduces or may
introduce process wastewater pollutants into a POTW.
b)
General definitions.
The Board incorporates by
reference 40 CFR 425.02
(1986).
This incorporation
includes no later
amendments or
editions.
C)
Sulfide analytical method.
The Board
incorporates by
reference 40 CFR 425.03
(1986).
This incorporation
includes no later amendments or editions.
d)
Applicability of sulfide standards.
The Board
incorporates by reference
40 CFR 425.04
(1986).
This
incorporation includes
no later
amendments or editions.
e)
Compliance dates.
The Board
incorporates by reference
40 CFR 425.05
(1986).
This incorporation includes no
later
amendments or
editions.
f)
Monitoring requirements.
The Board
incorporates by
reference 40 CFR 425.06
(1986).
This incorporation
includes no later
amendments or
editions.
(Source:
Added
at
11
Ill. Reg.
effective
)
Section 307.3501
Hair Pulp,
Chrome Tan, Retan—Wet Finish
a)
Applicability.
This Section applies to discharges
resulting from any tannery which, either exclusively or
in addition to other unhairing
and tanning operations,
processes raw or cured cattle or cattle—like hides into
finished
leather by chemically dissolving the hide hair,
chrome tanning and
retan—wet finishing.
b)
Specialized definitions.
None.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 425.15
(1986).
This incorporation includes no later
amendments
or editions.
79.497

—152—
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by
reference
40 CFR 425.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced
after July 2,
1979.
(Source:
Added
at
11
Ill. Req.
effective
Section 307.3502
Hair Save, Chrome Tan, Retan—Wet Finish
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes raw or cured
cattle or cattle—like hides
into finished leather by
hair
save unhairing,
chrome tanning and retan—wet
finishing.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 425.25
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 425.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
79.498

—153—
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July 2, 1979.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.3503
Hair Save or Pulp, Non—Chrome Tan, Retan—Wet
Finish
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes raw or
cured
cattle
or cattle—like hides
into finished leather by
hair
save or pulp unhairing, vegetable tanning
or alum,
syntans, oils and other
agents
for tanning and retan—wet
finishing.
b)
Specialized definitions.
None.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 425.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference
40 CFR 425.36
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July
2,
1979.
(Source:
Added
at 11
Ill.
Reg.
effective
79-499

—154—
Section 307.3504
Retan—Wet Finish—Sides
a)
Applicability.
This Section applies to discharges
resulting from any tannery which processes previously
tanned hides
and skins
(grade side only)
into finished
leather by retan—wet finishing.
b)
Specialized definitions:
None.
C)
Existing
sources:
U
The Board incorporates by reference
40 CFR 425.45
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 425.46
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July
2,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3505
No Beamhouse
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes cattle hides,
sheepskins or
splits
(hair previously removed and
pickled)
into finished
leather by chrome or non—chrome
tanning,
and retan—wet finishing.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 425.55
79-500

—155—
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 425.56
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced after
July 2,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3506
Through—the—Blue
a)
Applicability.
This Section applies to discharges
resulting from any tannery which processes raw or cured
cattle
or cattle—like hides through the blue tanned
state by hair pulp unhairing and chrome tanning;
rio
retan—wet finishing
is performed.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 425.65
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of
any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 425.66
(1986).
This incorporation includes no later
79.501

—156—
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after July 2,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3507
Shearling
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes raw or cured
sheep or sheep—like
skins with the wool
or hair retained
into
finished leather by chrome tanning and retan—wet
finishing.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 425.75
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference
40 CFR 425.76
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after July
2,
1979.
(Source:
Added
at 11
Ill.
Reg.
79-502

—157—
effective
Section 307.3508
Pigskin
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes
raw or cured
pigskins into finished leather by chemically dissolving
or pulping the hair
and tanning with chrome, then retan—
wet finishing.
b)
Specialized definitions.
None
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 425.85
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 425.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of
any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after July 2,
1979.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.3509
Retan—Wet Finish—Splits
a)
Applicability.
This Section applies
to discharges
resulting from any tannery which processes previously
unhaired and
tanned splits into finished leather by
retan—wet finishing.
b)
Specialized definitions.
None.
c)
Existing sources:
79-503

—158—
1)
The Board incorporates by reference 40 CFR 425.95
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 425.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after July 2,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
SUBPART BA:
GLASS MANUFACTURING
Section 307.3601
Insulation Fiberglass
a)
Applicability.
This Section applies to discharges
resulting from the production of insulation fiberglass
in which molten glass
is either directly or
indirectly
made,
continuously fiberized and chemically bonded into
a wool—like material.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 426.11
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 426.16
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
79-504

—159—
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation
the construction of
which
commenced after August
22,
1973.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3602
Sheet Glass Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which several mineral
ingredients
(sand,
soda ash, limestone, dolomite, cullet
and other
ingredients)
are mixed, melted
in
a furnace,
and drawn vertically from
a melting
tank
to form sheet
glass.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.21
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
I)
The Board
incorporates by reference
40 CFR 426.24
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person
subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 426.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility
or installation the construction of which
commenced after October
17,
1973.
(Source:
Added
at
11
Iii.
Reg.
79-505

—160—
effective
)
Section 307.3603
Rolled Glass Manufacturing
a)
Applicability.
This Section applies to discharges
resulting from the process
in which several mineral
ingredients
(sand,
soda ash,
limestone, dolomite, cullet
and other
ingredients)
are mixed, melted
in
a furnace
and cooled by rollers
to form rolled glass.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 426.34
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 426.36
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to
the pretreatment standards
i.ncorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
October
17,
1973.
(Source:
Added
at 11
Ill.
Req.
effective
)
Section 307.3604
Plate Glass Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which several mineral
ingredients
(sand,
soda ash, limestone, dolomite, cullet
and other
ingredients)
are melted
in
a furnace, pressed
between
rollers and finally ground
and polished
to form
plate glass.
79-506

—161—
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.41
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 426.44
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 426.45
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
17,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3605
Float Glass Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which several mineral
ingredients
(sand,
soda ash, limestone, dolomite, cullet
and other
ingredients)
are mixed, melted
in
a furnace
and floated
on
a molten tin bath
to produce float glass.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.51
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 426.55
79-507

—162—
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
Eicorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
17,
1973.
(Source:
Added
at 11
Ill. Req.
effective
)
Section 307.3606
Automotive Glass Tempering
a)
Applicability.
This Section applies
to discharges
resulting from the processes in which glass
is cut and
then passed through
a series of processes that grind and
polish
the edges, bend the glass and then temper
the
glass
to produce side and back windows for automobiles.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.61
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing
sources:
1)
The Board
incorporates
by
reference
40 CFR 426.64
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 426.66
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
79.508

—163—
commenced after October
17,
1973.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3607
Automotive Glass Laminating
a)
Applicability.
This Section applies
to discharges
resulting from the processes which laminate
a plastic
sheet between two layers of glass,
or which prepare the
glass
for lamination such as cutting, bending and
washing,
to produce automobile windshields.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 426.71
(1986).
This incorporation
includes
no later amendments or
editions.
c)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New
sources:
U
The Board
incorporates by reference 40 CFR 426.76
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction of which
commenced after October
17,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3608
Glass Container Manufacturing
a)
Applicability.
This Section applies to discharges
resulting from the process by which raw materials are
melted
in
a furnace and mechanically processed
into
glass containers.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.81
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
79.509

—164—
d)
New sources:
U
The Board incorporates
by
reference 40 CFR 426.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after August
21,
1974.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.3610
Glass Tubing
(Danner) Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process by which raw materials are
melted
in
a furnace and glass tubing mechanically drawn
from the furnace horizontally by means of
the Danner
process, which requires the intermittent quenching
of
cullet.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.101
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 426.106
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation
the construction of which
commenced after August
21,
1974.
(Source:
Added at
11
Ill.
Req.
79-510

—165—
effective
Section 307.3611
Television Picture Tube Envelope Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process by which raw materials are
melted
in
a furnace and processed
into television
picture tube envelopes.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.111
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 426.116
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of
any
contaminant to
a POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or installation the construction of which
commenced after August
21,
1974.
(Source:
Added at
11
Ill.
Reg.
effective
)
Section 307.3612
Incandescent Lamp Envelope Manufacturing
a)
Applicability.
This Section applies to discharges
resulting from the processes by which:
1)
Raw materials are melted
in
a furnace and
mechanically processed
into incandescent lamp
envelopes;
or
2)
Incandescent lamp envelopes are etched with
hydrofluoric acid
to produce
frosted envelopes.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.121
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
79-511

—166—
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 426.126
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation
the construction of which
commenced after August
21,
1974.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.3613
Hand Pressed and Blown Glass Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from the process by which raw materials are
melted
in
a furnace and processed by hand
into pressed
or blown glassware.
This includes those plants which:
1)
Produce leaded glass and employ hydrofluoric acid
finishing techniques
2)
Produce non—leaded glass
and employ hydrofluoric
acid finishing techniques;
or
3)
Produce leaded
or non—leaded glass
and do not
employ hydrofluoric acid finishing techniques.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 426.131
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 426.136
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
79-512

—167—
contaminant
to
a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after August
21,
1974.
(Source:
Added
at
11
Ill.
Req.
effective
SUBPART BB:
ASBESTOS MANUFACTURING
Section 307.3701
Asbestos—Cement Pipe
a)
Applicability.
This Section applies
to discharges.
resulting from the process
in which asbestos, Portland
cement,
silica and other
ingredients are used
in the
manufacturing
of asbestos—cement pipe.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 427.11
(1986).
This incorporation
includes
rio later
amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 427.14
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 427.16
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility
or installation the construction of which
commenced after October
30,
1973.
(Source:
Added at
11
Ill.
Reg.
effective
79-513

—168—
Section 307.3702
Asbestos—Cement Sheet
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which asbestos, Portland
cement, silica
and other
ingredients
are used
in the
manufacturing
of asbestos—cement sheets.
Discharges
resulting_from_manufacture
of asbestos—cement sheet
laboratory tops are specifically excluded from the
provisions of this Section.
b)
Specialized definitions.
The
Board incorporates by
reference 40 CFR 427.21
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 427.24
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 427.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
~j
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
30,
1973.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.3703
Asbestos Paper
(Starch Binder)
a)
Applicability.
This Section applies to discharges
resulting from the process
in which asbestos, starch
binders and other
ingredients are used
in the
manufacture of
asbestos paper
(starch binder).
b)
Specialized definitions.
The Board
incorporates by
79-514

—169—
reference 40 CFR 427.31
(1986).
This incorporation
includes no
later amendments
or editions.
c)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 427.34
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten
or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 427.36
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
30,
1973.
(Source:
Added
at
11
Ill. Req.
effective
Section
307.3704
Asbestos Paper
(Elastomeric Binder)
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which asbestos,
elastomeric binder
and other
ingredients are used
in the
manufacture
of asbestos paper
(elastomeric binder).
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 427.41
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
U
The Board
incorporates by reference 40 CFR 427.44
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
79-515

—170—
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 427.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
30,
1973.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3705
Asbestos Millboard
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which asbestos
in
combination with various other materials such as cement,
starch, clay,
lime and mineral wool are used
in the
manufacture of asbestos millboard.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 427.51
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference 40 CFR 427.54
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 427.56
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-516

—171—
cause,
threaten or allow
the discharge of
any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after October
30,
1973.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3706
Asbestos Roofing
a)
Applicability.
This Section applies
to discharges
resulting from the process
in which asbestos paper
is
saturated with asphalt or coal
tar with the subsequent
application
of various surface treatments to produce
asbestos roofing products.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 427.61
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 427.64
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 427.66
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POT~in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction
of which
commenced after October
30,
1973.
(Source:
Added
at
11
Ill.
Reg.
effective
79.517

—172—
Section 307.3707
Asbestos Floor Tile
a)
Applicability.
This Section applies
to discharges
resulting
from the process
in which asbestos, polyvinyl
chloride resin, chemical stabilizers, limestone and
other
fillers are used
in the manufacture
of asbestos
floor
tile.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 427.71
(1986).
This incorporation
includes no later amendments
or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 427.74
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 427.76
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of
which
commenced after October
30,
1973.
(Source:
Added
at
11
Ill. Req.
effective
Section 307.3708
Coating
or Finishing
of Asbestos Textiles
a)
Applicability.
This Section applies
to discharges
resulting from the process of coating
or
impregnating
asbestos textiles with materials which impart specific
desired qualities
to the finished product.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 427.81
(1986).
This incorporation
includes no
later amendments or editions.
79.518

—173—
c)
Existing
sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 427.86
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building, structure,
facility or installation the construction of which
commenced after August
29, 1974.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3709
Solvent Recovery
a)
Applicability.
This Section applies
to discharges
resulting from the process
of solvent recovery
in the
manufacture of asbestos products.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 427.91
(1986).
This incorporation
includes
no later
amendments or
editions.
c)
Existing sources:
These
sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 427.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility
or
installation the construction of which
commenced
after August
29,
1974.
(Source:
Added
at
11
Ill.
Reg.
79.519

—174—
effective
)
Section 307.3710
Vapor Absorption
a)
Applicability.
This Section applies
to discharges
resulting from the removal
of volatilized organic
materials from atmospheric emissions by means of wet
scrubbers.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 427.101
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and
specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 427.106
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after August
29,
1974.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.3711
Wet Dust Collection
a)
Applicability.
This Section applies
to discharges
resulting from the removal
of dust (particulates)
from
atmospheric emissions by means of wet scrubbers.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 427.111
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
These
sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 427.116
(1986).
This incorporation includes
no later
79.520

—175—
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after August
29,
1974.
(Source:
Added at
11
Ill.
Req.
effective
SUBPART BC:
RUBBER MANUFACTURING
Section 307.3801
Tire and Inner Tube Plants
a)
Applicability.
This Section applies to discharges
resulting from the production of pneumatic tires and
inner tubes in tire and inner tube plants.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.11
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 428.16
(1986).
This incorporation includes no later
amendments or editions.
2~
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction
of which
commenced after December
18,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.3802
Emulsion Crumb Rubber
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of emulsion crumb rubber,
79-521

—176—
other
than acrylonitrilebutadiene rubber.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.21
(1986).
This incorporation
includes_no_later amendments
or editions.
C)
Existing sources:
These sources
shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
All sources are regulated as existing
sources.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.3803
Solution Crumb Rubber
a)
Applicability.
This Section applies
to di~charges
resulting from the manufacture of crumb rubber.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 428.31
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.3804
Latex Rubber
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of latex rubber.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 428.41
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 428.46
(1986).
This incorporation includes no later
amendments or
editions.
79.522

—177—
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation
the construction of which
commenced after December
18,
1979.
(Source:
Added at
11
Ill. Reg.
effective
)
Section 307.3805
Small—Sized General Molded, Extruded, and
Fabricated Rubber Plants
a)
Applicability.
This Section applies
to discharges
resulting
from the production of molded, extruded
or
fabricated
rubber products, foam rubber backing,
rubber
cement—dipped goods or retreaded tires by small—sized
plants.
Specifically excluded from this Section are
discharges resulting from the production of latex—based
products, tires and inner tubes,
and those discharges
from textile plants subject
to Subpart
K.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 428.51
(1986).
This incorporation
includes
no later amendments
or editions.
C)
Existing sources:
These sources
shall comply with the
general
and specific pretreatment requirements of
Subpart B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 428.56
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction
of which
commenced after December
18,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.3806
Medium—Sized General Molded,
Extruded,
and
Fabricated Rubber
Plants
79-523

—178—
a)
Applicability.
This Section applies
to discharges
resulting from the production of molded,
extruded or
fabricated rubber products, foam rubber backing,
rubber
cement—dipped goods or retreaded tires by medium—sized
plants.
Specifically excluded from this Section are
discharges resulting from the production of latex—based
products,
tires and inner
tubes, and discharges from
textile plants subject
to the provisions of Subpart
K.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 428.61
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources
shall comply with the
general and
specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 428.66
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
~ommenced after December
18,
1979.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3807
Large—Sized General Molded,
Extruded,
and
Fabricated Rubber Plants
a)
Applicability.
This Section applies to discharges
resulting
from the production of molded,
extruded
or
fabricated
rubber products, foam rubber backing,
rubber
cement—dipped goods or
retreaded tires by large—sized
plants.
Specifically excluded from this Section are
discharges resulting from the production of latex—based
products, tires and
inner tubes,
and discharges from
textile plants subject to Subpart
K.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.71
(1986).
This incorporation
includes
no later
amendments
or editions.
C)
Existing sources:
These
sources shall comply with the
79.524

—179—
general and specific pretreatment requirements of
Subpart B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 428.76
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after December
18,
1979.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.3808
Wet Digestion Reclaimed Rubber
a)
Applicability.
This Section applies
to discharges
resulting
from the production of reclaimed
rubber by use
of the wet digestion process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.81
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 428.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction of which
commenced after
December
18,
1979.
(Source:
Added
at 11
Ill.
Reg.
effective
79-525

—180—
Section 307.3809
Pan, Dry Digestion and Mechanical Reclaimed
Rubber
a)
Applicability.
This Section applies
to discharges
resulting from the production of reclaimed rubber except
when produced by the wet digestion process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.91
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 428.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
December 18,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3810
Latex—Dipped, Latex—Extruded and Latex—Molded
Rubber
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of latex—dipped, latex—
extruded or latex—molded products with the exception of
discharges from textile plants subject to Subpart K.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 428.101
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
These sources shall
comply with the
general
and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR
428.106
79-526

—181—
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after December
18,
1979.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.3811
Latex Foam
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of latex foam except for
discharges from textile plants subject
to Subpart K.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 428.111
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 428.116
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction of which
commenced after December
18,
1979.
(Source:
Added
at
11
Ill.
Reg.
effective
SUBPART BD:
TIMBER PRODUCTS PROCESSING
Section 307.3900
General Provisions
a)
Applicability.
This Subpart
applies
to any timber
79.527

—182—
products processing operation,
and any plant producing
insulation board with wood as the major
raw material,
which introduces or may introduce process wastewater
pollutants into a POTW.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 429.11
(1986).
This incorporation
includes
no later amendments or editions.
(Source:
Added at 11
Ill. Reg.
effective
)
Section 307.3901
Barking
a)
Applicability.
This Section applies
to discharges
resulting from the barking
of logs by plants
in SIC
(Standard Industrial Classification,
as defined
in
35
Ill.
Adm. Code 310.110)
major group 24, or from plants
producing
insulation board
(SIC group 2661)
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates
by
reference 40 CFR 429.25
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New
sources:
U
The Board incorporates by reference
40 CFR 429.26
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.3902
Veneer
79-528

—183—
a)
Applicability.
This Section applies
to discharges
resulting from any plant which manufactures veneer
and
does not store or hold raw materials in wet storage
conditions.
b)
Specialized
definitions.
None.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 429.35
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 429.36
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after October
31,
1979.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.3903
Plywood
a)
Applicability.
This
Section
applies
to
discharges
resulting from any plywood production plant
that does
not store or hold
raw materials
in wet storage
conditions.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 429.45
(1986).
This incorporation includes
no later
amendments
or editions.
79.529

—184—
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference 40 CFR 429.46
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
~j
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
)
Section 307.3904
Dry Process Hardboard
a)
Applicability.
This Section applies
to discharges
resulting from any plant which produces hardboard
products using
the dry matting process
for
forming the
board mat.
b)
Specialized definitions.
None.
c)
Existing
sources:
U
The Board
incorporates by reference
40 CFR 429.55
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 429.56
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
79.530

—185—
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
~j
“New source”
means any building, structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at
11
Ill. Req.
,
effective
Section 307.3905
Wet Process Hardboard
a)
Applicability.
This Section applies to discharges
resulting from any plant which produces hardboard
products using
the wet matting process for
forming the
board mat.
b)
Specialized
definitions.
None.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 429.65
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 429.66
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after
October
31,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3906
Wood Preserving—Water Borne or Nonpressure
a)
Applicability.
This Section applies
to discharges
79-531

—186—
resulting
from all nonpressure wood preserving treatment
processes or all pressure wood preserving treatment
processes employing water borne
inorganic salts.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board incorporates
by
reference
40 CFR 429.75
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference in subsection
(I)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New
sources:
I)
The Board incorporates b~yreference
40 CFR 429.76
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.3907
Wood Preserving—Steam
a)
Applicability.
This Section applies
to discharges
resulting from wood—preserving processes that use direct
steam impingement on wood
as the predominant
conditioning method;
processes that use the vapor
drying process as the predominant conditioning method;
direct steam conditioning processes that use the same
retort to treat both salt and oil type preservatives;
or steam conditioning processes which apply both salt
type and oil type preservatives to the same stock.
b)
Specialized
definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 429.85
79-532

—187—
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New
sources:
1)
The Board incorporates by reference 40 CFR 429.86
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in
violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3908
Wood Preserving—Boulton
a)
Applicability.
This Section applies
to discharges
resulting
from wood preserving operations which use
the
Boulton process
as the predominant method
of
conditioning stock.
b)
Specialized
definitions.
None.
c)
Existing
sources:
1)
The Board incorporates by reference
40 CFR 429.95
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shala
cause, threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d.)
New
sources:
1)
The
Board
incorporates
by
reference
40
CFR
429.96
(1986).
This incorporation includes no later
amendments
or
editions.
79-533

—188—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
31,
1979.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.3909
Wet Storage
a)
Applicability.
This Section applies to discharges
resulting from the storage of unprocessed wood,
i.e.,
the storage of logs or roundwood before or
after
removal
of bark
in self—contained bodies of water
(mill ponds
or
log ponds),
or
the storage of logs or roundwood
on land
during which water
is sprayed
or deposited intentionally
on the logs (wet decking).
b)
Specialized definitions.
None.
C)
Existing sources:
U
The
Board
incorporates by reference
40 CFR 429.105
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 429.106
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced
after
October
31,
1979.
79.534

—189—
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.3910
Log Washing
a)
Applicability.
This Section applies to discharges
resulting from the log washing process
in which water
under pressure
is applied to logs
for
the purpose of
removing
foreign material
from the surface of the
log
before further processing.
b)
Specialized
definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 429.115
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New
sources:
1)
The Board incorporates by reference 40 CFR 429.116
(1986).
This incorporation includes
no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.3911
Sawmills and Planing Mills
a)
Applicability.
This Section applies to discharges
resulting from the timber products processing procedures
that include all
or part of the following operations:
bark removal
(other
than hydraulic barking
as defined
in
Section
307.3901),
sawing,
resawing,
edging,
trimming,
planing
and
machining.
b)
Specialized definitions.
None.
79-535

—190—
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 429.125
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by
reference 40 CFR 429.126
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction
of which
commenced after October
31,
1979.
(Source:
Added at 11
Ill. Reg.
effective
)
Section 307.3912
Finishing
a)
Applicability.
This Section applies to discharges
resultin~from the drying, ~laning, dipping,
staining,
end_coating, moisture proofing, fabrication or by-
product utilization timber processing operations not
otherwise covered by specific guidelines and standards.
b)
Specialized definitions.
None.
C)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 429.135
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
79.536

—191—
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 429.136
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.3913
Particleboard Manufacturing
a)
Applicability.
This Section applies
to discharges
resulting from any plant which manufactures
particleboard.
b)
Specialized
definitions.
None.
c)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 429.145
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New
sources:
1)
The Board incorporates by reference
40 CFR 429.146
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
31,
1979.
79,537

—192—
(Source:
Added at
11 Ill.
Req.
effective
)
Section 307.3914
Insulation Board
a)
Applicability.
This Section applies
to discharges
resulting from plants which produce insulation board
using wood
as the primary raw material.
Specifically
excluded
from this Section
is the manufacture of
insulation board from the primary raw material
bagasse.
b)
Specialized definitions.
None.
C)
Existing sources:
U
The Board
incorporates by reference
40 CFR 429.155
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1.)
The Board
incorporates by reference
40 CFR 429.156
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
31, 1979.
(Source:
Added
at
11 Ill.
Reg.
effective
)
Section 307.3915
Wood Furniture and Fixture Production Without
Water Wash Spray Booth(s)
or Without Laundry
Facilities
a)
Applicability.
This
Section
applies
to
discharges
resulting from the manufacture of wood furniture and
fixtures
at establishments that:
1)
Do
not utilize water wash
spray booths
to collect
79-538

—193—
and contain the overspray from spray application of
finishing materials;
and
2)
Do not maintain on—site laundry facilities
for
fabric utilized
in various finishing operations.
b)
Specialized definitions.
None.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 429.165
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 429.166
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after October 31,
1979.
(Source:
Added
at
11
Ill. Req.
,
effective
Section 307.3916
Wood Furniture and Fixture Production with
Water Wash Spray Booth(s)
or With Laundry
Facilities
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of wood furniture and
fixtures at establishments that either:
1)
Utilize water wash
spray booths
to collect and
contain the overspray from spray application of
finishing materials;
or
2)
Utilize on—site laundry facilities for
fabric
utilized
in various finishing operations.
79-539

—194—
b)
Specialized definitions.
None.
C)
Existing sources:
U
The Board incorporates by reference 40 CFR 429.175
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 429.176
(1986).
This incorporation includes no
later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to a POTW in violation of such
standards.
~j,
“New source” means any building, structure,
facility or installation the construction of which
commenced after October
31,
1979.
(Source:
Added
at 11
Ill.
Req.
effective
)
SUBPART BE:
PULP,
PAPER AND PAPERBOARD
Section 307.4000
General Provisions
a)
Applicability.
This Subpart applies to any pulp,
paper
or paperboard mill which introduces
or may introduce
process wastewater
pollutants into
a POTW.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 430.01
(1986).
This incorporation
includes no later amendments or editions.
(Source:
Added at 11 Ill.
Reg.
effective
Section 307.4001
Unbleached Kraft
a)
Applicability.
This Section applies
to discharges
resulting from the production of pulp and paper
at
unbleached
,craft mills.
79.540

—195—
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.11
(1986).
This incorporation
includes
no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 430.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 430.17
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced after January
6,
1981.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.4002
Semi—Chemical
a)
Applicability.
This Section applies
to discharges
resulting from the
integrated production of pulp and
paper
at semi—chemical mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.21
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference
40 CFR 430.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
79-541

—196—
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates
by
reference 40 CFR 430.27
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after January
6,
1981.
(Source:
Added at
11
Ill.
Reg.
,
effective
Section 307.4004
Unbleached Kraft—Neutral Sulfite Semi—Chemical
(Cross Recovery)
a)
Applicability.
This Section applies to discharges
resulting from the production of pulp and paper
at
unbleached kraft—neutral sulfite semi—chemical
(cross
recovery)
mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.31
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 430.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates
by
reference 40 CFR 430.47
c1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-542

—197—
cause, threaten or allow the discharge of
any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January
6, 1981.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.4005
Paperboard From Wastepaper
a)
Applicability.
This Section
applies to discharges
resulting from the production of paperboard from
wastepaper.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.51
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 430.56
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
Contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 430.57
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.4006
Dissolving Kraft
79-543

—198—
a)
Applicability.
This Section applies to discharges
resulting from the production of dissolving pulp at
kraft mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.61
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 430.66
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
~àntaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates
by
reference 40 CFR 430.67
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January 6,
1981.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.4007
Market Bleached Kraft
a)
Applicability.
This Section applies
to discharges
resulting from the production of market pulp at bleached
kraft mills.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 430.71
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 430.76
(1986).
This incorporation includes no later
amendments
or editions.
79.544

—199—
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 430.77
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill. Req.
effective
)
Section 307.4008
BCT Bleached Kraft
a)
Applicability.
This Section applies
to discharges
resulting from the integrated production of paperboard,
coarse paper or tissue
paper
at bleached kraft mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.81
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 430.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 430.87
(1986).
This incorporation includes no later
amendments
or editions.
79-545

—200—
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
“New source” means any building, structure,
facility or installation the construction of which
commenced after January 6,
1981.
(Source:
Added at
11 Ill.
Reg.
,
effective
)
Section 307.4009
Fine Bleached Kraft
a)
Applicability.
This Section applies to discharges
resulting from the
integrated production
of pulp or fine
papers
at bleached kraft mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.91
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 430.96
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 430.97
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
“New source” means any building, structure,
facility or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
effective
79-546

—201—
Section 307.4010
Papergrade Sulfite
(Blow Pit Wash)
a)
Applicability.
This Section applies to discharges
resulting from the
integrated production of pulp and
paper
at papergrade sulfite mills, where blow pit pulp
washing techniques are used.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.101
(1986).
This incorporation
includes
no later amendments or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 430.106
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 430.107
(1986).
This incorporation includes
no
later
amendments or editions.
2)
No
person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January 6,
1981.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.4011
Dissolving Sulfite Pulp
a)
Applicability.
This Section applies
to discharges
resulting from the production of pulp at dissolving
sulfite mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.111
(1986).
This incorporation
includes no later
amendments
or editions.
c)
Existing
sources:
79-547

—202—
1)
The Board
incorporates by reference 40 CFR 430.116
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
Contaminant to
a POTW in violation of such
standards.
d)
New sources:
U
The Board incorporates
by
reference
40 CFR 430.117
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.4012
Groundwood—Chemi—Mechanical
a)
Applicability.
This Section applies
to discharges
resulting from the production of pulp and paper
at
groundwood chemi—mechanical mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.121
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.4013
Groundwood—Thermo—Mechanical
a)
Applicability.
This Section applies
to discharges
resulting from the production of pulp and paper
at
groundwood mills through the application of the thermo—
79-548

—203—
mechanical process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.131
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 430.136
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 430.137
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility
or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill. Reg.
effective
Section 307.4014
Groundwood—CMN Papers
a)
Applicability.
This Section applies to discharges
resulting from the integrated production of pulp and
coarse paper, molded pulp products and newsprint
at
groundwood mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.141
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 430.146
(1986).
This incorporation includes no later
amendments or editions.
79.549

—204—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 430.147
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation
the construction of which
commenced after January 6,
1981.
(Source:
Added
at
11
Ill. Req.
effective
Section 307.4015
Groundwood-Fine Papers
a)
Applicability.
This Section applies to discharges
resulting from the
integrated production of pulp and
fine paper
at groundwood mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.151
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 430.156
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 430.157
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
79.550

—205—
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at 11
Ill.
Req.
effective
Section 307.4016
Soda
a)
Applicability.
This Section applies
to discharges
resulting from the integrated
production of pulp and
paper
at soda mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.161
(1986).
This incorporation
includes no later
amendments or editions.
C)
Existing sources:
1)
The Board incorporates by reference 40 CFR 430.166
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 430.167
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction
of which
commenced after January
6,
1981.
(Source:
Added
at
11 Ill.
Reg.
effective
Section 307.4017
Deink
79.551

—206—
a)
Applicability.
This Section applies to discharges
resulting from
the integrated production of pulp and
paper
at deink mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.171
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 430.176
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference 40 CFR 430.177
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January 6,
1981.
(Source:
Added at
11
Ill. Req.
,
effective
Section 307.4018
Nonintegrated—Fine Papers
a)
Applicability.
This Section applies
to discharges
resulting from the production of fine paper
at
nonintegrated mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.181
(1986).
This incorporation
includes
no later
amendments or
editions.
C)
Existing sources:
U
The Board
incorporates by reference
40 CFR 430.186
(1986).
This incorporation includes
no later
79.552

—207—
amendments or editions.
2)
No person subject to the~pretreatmentstandards
incorporated by reference
in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference
40 CFR 430.187
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten
or allow
the discharge of
any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.4019
Nonintegrated—Tissue Papers
a)
Applicability.
This Section applies to discharges
resulting from the production of tissue papers at non—
integrated mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.191
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 430.196
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 430.197
(1986).
This incorporation includes no
later
amendments or editions.
79.553

—208—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 6,
1981.
(Source:
Added at
11
Ill. Req.
effective
Section 307.4020
Tissue From Wastepaper
a)
Applicability.
This Section applies
to discharges
resulting from the production of tissue paper
from
wastepaper without deinking
at secondary fiber mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.201
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 430.206
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
U
The Board
incorporates by reference
40 CFR 430.207
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person
subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility
or installation the construction of which
commenced after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
effective
79-554

—209—
Section 307.4021
Papergrade Sulfite
(Drum Wash)
a)
Applicability.
This Section applies to discharges
resulting from the integrated production of pulp and
paper
at papergrade sulfite mills, where vacuum or
pressure drums are used to wash pulp.
b)
Specialized definitions.
The Board incorporates by
re.ference 40 CFR 430.211
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The
Board
incorporates by reference
40 CFR 430.216.
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
U
The Board incorporates by reference 40 CFR 430.217
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility
or installation the construction of which
commenced after January
6,
1981.
(Source:
Added at
11
111.
Req.
effective
Section 307.4022
Unbleached Kraft and Semi—Chemical
a)
Applicability.
This Section applies
to discharges
resulting from the production of pulp and paper
at
combined unbleached
kraft and semi—chemical mills,
in
which the
spent semi—chemical cooking
liquor
is burned
within the unbleached
kraft chemical recovery system.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.221
(1986).
This incorporation
includes
no later amendments
or editions.
79-555

—210—
C)
Existing sources:
U
The Board incorporates by reference 40 CFR 430.226
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 430.227
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January
6, 1981.
(Source:
Added at
11 Ill.
Reg.
effective
Section 307.4023
Wastepaper—Molded Products
a)
Applicability.
This Section applies
to discharges
resulting from the production
of molded products from
wastepaper without deinking
at secondary fiber mills.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 430.231
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 430.236
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to
a POTW in violation of such
standards.
79-556

—211—
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 430.237
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of
which
commenced after January
6, 1981.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.4024
Nonintegrated—Lightweight Papers
a)
Applicability.
This Section applies
to discharges
resulting from the production of lightweight paper
at
nonintegrated mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.241
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 430.246
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 430.247
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of
any
contaminant to
a POTW
in violation of
such
standards.
3)
“New source” means any building,
structure,
79.557

—212—
facility or
installation the construction of which
commenced
after January
6,
1981.
(Source:
Added
at
11
Ill.
Req.
,
effective
)
Section 307.4025
Nonintegrated—Filter
and Nonwoven Papers
a)
Applicability.
This Section applies
to discharges
resulting from the production of filter
and nonwoven
papers at nonintegrated mills.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 430.251
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 430.256
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 430.257
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January
6,
1981.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.4026
Nonintegrated—Paperboard
a)
Applicability.
This Section applies to discharges
resulting from the production of ~aperboard at
nonintegrated mills.
The production of electrical
grades
of board
and matrix board
is not included
in this
Section.
79-558

—213—
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 430.261
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 430.266
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 430.267
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after January
6, 1981.
(Source:
Added
at
11
Ill.
Reg.
effective
SUBPART BF:
BUILDERS’ PAPER AND BOARD MILLS
Section 307.4101
Builder’s Paper and Roofing Felt
a)
Applicability.
This Section applies
to discharges
resulting from the production of builders’
paper
and
roofing felt from wastepaper.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 431.11
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 431.16
(1986).
This incorporation includes no later
amendments or
editions.
79-559

—214—
2)
No person subject to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 431.17
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
iacility or
installation the construction of which
commenced after January 6,
1981.
(Source:
Added at 11
Ill.
Req.
effective
)
SUBPART BG:
MEAT PRODUCTS
Section 307.4201
Simple Slaughterhouse
a)
Applicability.
This Section applies to discharges
resulting from the production of
red meat carcasses,
in
whole
or part,
by simple slaughterhouses.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 432.11
(1986).
This incorporation
includes no later amendments
or editions.
C)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 432.14
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
Incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
c5)
New
sources:
1)
The Board incorporates by reference
40 CFR 432.16
(1986).
This incorporation includes no later
79-560

—215—
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after October
29,
1973.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.4202
Complex Slaughterhouse
a)
Applicability.
This Section applies
to discharges
resulting from the production of red meat carcasses,
in
whole or part,
by complex
slaughterhouses.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 432.21
(1986).
This incorporation
includes
no later
amendments
or editions.
C)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 432.24
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to
a POTW in violation of
such
standards.
d)
New sources:
U
The Board incorporates by reference 40 CFR 432.26
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source1’ means any building,
structure,
facility or
installation
the construction of which
commenced after October
29,
1973.
(Source:
Added at
11
Ill.
Reg.
79-561

—216—
effective
)
Section 307.4203
Low—Processing Packinghouse
a)
Applicability.
This Section applies to discharges
resulting from the production of red meat carcasses in
whole or
part, by low—processing packinghouses.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 432.31
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 432.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow
the discharge of any
contaminant
to a POTW
in violation of such
standards.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 432.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after October
29,
1973.
(Source:
Added at
11
Ill. Req.
effective
)
Section 307.4204
High-Processing Packinghouse
a)
Applicability.
This Section applies
to discharges
resulting from the production of red meat carcasses,
in
whole
or part,
by high—processing packinghouses.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 432.41
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
79-562

—217—
1)
The Board incorporates by reference 40 CFR 432.44
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to a POTW in violation of
such
standards.
~j
New sources:
1)
The Board
incorporates by reference
40 CFR 432.46
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the Construction of which
commenced after October
29,
1973.
(Source:
Added at
11
Ill.
Reg.
,
effective
)
Section 307.4205
Small Processor
a)
Applicability.
This Section applies to discharges
resulting from the production of finished meat products
such as fresh meat cuts,
smoked products, canned
products, hams,
sausages, luncheon meats
or similar
products by
a small processor.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 432.51
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing sources:
These sources shall comply with
the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 432.56
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79.563

—218—
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after August 28,
1974.
(Source:
Added
at 11 Ill.
Req.
effective
)
Section 307.4206
Meat Cutter
a)
Applicability.
This Section applies
to discharges
resulting from the fabrication
or manufacture
of fresh
meat cuts such as steaks,
roasts,
chops, etc.
by a meat
cutter.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 432.61
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and
specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference
40 CFR 432.66
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after August 28,
1974.
(Source:
Added at
11
Ill.
Req.
effective
Section 307.4207
Sausage and Luncheon Meats Processor
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of fresh meat cuts,
sausage, bologna and other
luncheon meats
by
a sausage
and luncheon meat processor.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 432.71
(1986).
This incorporation
79.564

—219—
includes
no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference 40 CFR 432.76
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation
the construction of which
commenced after August
28, 1974.
(Source:
Added at
11
Ill.
Reg.
effective
Section 307.4208
Ham Processor
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture
of hams alone or
in
combination with other
finished
products by a ham
processor.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 432.81
(1986).
This incorporation
includes no
later amendments
or editions.
C)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements
of
Subpart
B.
d)
New sources:
1)
The Board incorporates by reference
40 CFR 432.86
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
79.565

—220—
commenced after August 28, 1974.
(Source:
Added at
11
Ill.
Req.
effective
)
Section 307.4209
Canned Meats Processor
a)
Applicability.
This Section applies
to discharges
resulting
from the manufacture of canned meats, alone or
in_combination_with any other
finished products,
by a
canned meats processor.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 432.91
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
d)
New sources:
U
The Board incorporates by reference 40 CFR 432.96
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after August
28,
1974.
(Source:
Added
at
11 Ill.
Reg.
effective
)
Section 307.4210
Renderer
a)
Applicability.
This Section applies
to discharges
resulting from the manufacture of meat meal, dried
animal by—product residues (tankage), animal
oils,
grease and tallow, perhaps
including hide curing, by
a
renderer.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 432.101
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
79-566

—221—
d)
New sources:
U
The Board
incorporates by reference 40 CFR 432.106
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after August
28,
1974.
(Source:
Added at
11
Ill.
Req.
effective
SUBPART BH:
METAL FINISHING
Section 307.4300
General Provisions
a)
Applicability.
Except
as provided
in subsections
(a)(3)
or
(a)(4), this Subpart applies
to discharges resulting
from plants which perform on any basis material any of
the six metal finishing operations listed
in subsection
(a)(l).
If any of
those six operations are present,
then this Subpart applies also
to discharges from the
forty process operations specified
in subsection
(a)(2).
1)
Six metal
finishing operations:
Electroplating,
electrolessplating, anodizing,
coating
(chromating,
phos~hatingand
coloring), chemical etching and
milling and printed circuit board manufacture.
2)
Forty additional process operations:
Cleaning,
machining, grinding, polishing,tumbling,
burnishing,
impact deformation, pressure
deformation, shearing, heat treating, thermal
cutting, welding, brazing,
soldering,
flame
spraying, sand blasting, other abrasive jet
machining, electric discharge machining,
electrochemical machining,
electron beam machining,
laser beam machining, plasma arc machining,
ultrasonic machining,
sintering, laminating, hot
dip coating,
sputtering, vapor plating, thermal
infusion, salt bath descaling,
solvent degreasing,
paint stripping, painting, electrostatic painting,
electropainting, vacuum metalizing,
assembly,
calibration, testing and mechanical plating.
3)
Exclusions:
This Subpart does not apply
if there
79-567

—222—
are pretreatment standards which
are effective and
applicable
for the following industrial categories:
A)
Nonferrous metal smelting and refinir~g
(Subpart V)
B)
Coil coating
(Subpart CN)
C)
Porcelain enameling
(Subpart CC)
D)
Battery manufacturing (Subpart CJ)
E)
Iron and steel
(Subpart U)
F)
Metal casting foundries
(Subpart CM)
G)
Aluminum forming
(Subpart CP)
H)
Copper
forming
(Subpart CQ)
I)
Plastic molding and
forming
(Subpart CL)
J)
Nonferrous
forming (Subpart CT);
and
K)
Electrical
and electronic components
(Subpart
CR).
4)
This Subpart does not apply
to:
A)
Metallic platemaking and gravure cylinder
preparation conducted within
or
for printing
and publishing
facilities; and
B)
Existing
indirect discharging job shops and
independent printed
circuit board
manufacturers which are covered by Subpart N.
b)
General definitions.
The Board incorporates by
reference 40 CFR 433.11
(1986),
as amended
at
51 Fed.
Req.
40421,
November
7,
1987.
This incorporation
includes
no later amendments
or editions.
c)
Monitoring requirements.
The Board
incorporates by
reference 40 CFR 433.12
(1986).
This incorporation
includes no later
amendments or editions.
(Source:
Added at
Ill.
Req.
effective
Section 307.4301
Metal Finishing
a)
Existing sources:
1)
The Board incorporates by reference
40 CFR 433.15
79-568

—223—
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
b)
New sources:
1)
The Board incorporates by reference 40 CFR 433.17
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after August
31, 1982.
(Source:
Added at
11
Ill.
Req.
effective
)
SUBPART BN:
PHARMACEUTICAL MANUFACTURING
Section 307.4900
General
Provisions
a)
Applicability.
This Subpart applies
to any
pharmaceutical manufacturing facility which introduces
or may introduce process wastewater pollutants
into
a
POT~.
b)
General definitions.
The Board incorporates by
reference
40 CFR 439.1
(1986).
This incorporation
includes
no later
amendments
or editions.
c)
Monitoring requirements.
The Board incorporates by
reference 40 CFR 439.2
(1986).
This incorporation
includes
no later amendments
or editions.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.4901
Fermentation Products
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of pharmaceuticals by
fermentation.
79.569

—224—
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 439.11
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 439.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
The Board
incorporates
by
reference
40 CFR 439.17
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
£ncorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
.~J
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after November
26,
1982.
(Source:
Added at 11
Ill.
Reg.
,
effective
Section 307.4902
Extraction Products
a)
Applicability.
This Section applies to discharges
resulting from the manufacture
of pharmaceuticals by
extraction.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 439.21
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
1)
The Board
incorporates
by
reference 40 CFR 439.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person
subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
79.570

—225—
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The
Board
incorporates
by
reference
40
CFR
439.27
(1986).
This
incorporation
includes
no
later
amendments
or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after November
26,
1982.
(Source:
Added
at
11
Ill. Reg.
,
effective
)
Section 307.4903
Chemical Synthesis Products
a)
Applicability.
This
Section
applies
to
discharges
resulting from the manufacture of pharmaceuticals by
chemical synthesis.
b)
Specialized definitions.
The Board
incorporates by
reference
40
CFR
439.31
(1986).
This
incorporation
includes
no later
amendments
or editions.
c)
Existing
sources:
1)
The
Board
incorporates
by
reference
40
CFR
439.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New
sources:
1)
The Board
incorporates by reference 40 CFR 439.37
(1986).
This incorporation includes no
later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
79.571

—226—
standards.
3)
“New
source”
means
any
building,
structure,
facility or installation the construction of which
commenced after November
26,
1982.
(Source:
Added at 11
Ill.
Reg.
effective
)
Section 307.4904
Mixing/Compounding and Formulation
a)
Applicability.
This Section applies
to discharges
resulting from mixing/compounding and formulation
operations of pharmaceutical products.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 439.41
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing
sources:
1)
The
Board
incorporates
by
reference
40
CFR
439.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a
POTW
in
violation
of
such
standards.
d)
New
sources:
1)
The
Board
incorporates
by
reference
40
CFR
439.47
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction
of which
commenced after November
26,
1982.
(Source:
Added
at 11
Ill.
Req.
effective
Section
307.4905
Research
a)
Applicability.
This Section applies
to discharges
resulting from pharmaceutical research.
79-572

—227—
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR
439.51
(1986).
This incorporation
includes no
later amendments
or editions.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 439.56
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference 40 CFR 439.57
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
26,
1982.
(Source:
Added
at
11
Ill.
Reg.
effective
)
SUBPART BR:
PAVING AND ROOFING MATERIALS
(TARS AND ASPHALT)
Section 307.5301
Asphalt Emulsion
a)
Applicability.
This Section applies to discharges
resulting from the production
of asphalt paving
and
roofing emulsions.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 443.11
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall
comply, with
the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
79.573

—228—
1)
The Board incorporates by reference 40 CFR 443.16
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
~j
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 10,
1975.
(Source:
Added
at
11
Ill. Req.
effective
Section 307.5302
Asphalt Concrete
a)
Applicability.
This Section applies to discharges
resulting from the production of asphalt concrete.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 443.21
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Existing
sources:
These sources shall comply with the
general and specific pretreatment requirements
of
Subpart
B.
ci)
New sources:
U
The Board incorporates by reference
40 CFR 443.26
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after January 10,
1975.
(Source:
Added
at 11
Ill. Req.
effective
Section 307.5303
Asphalt Roofing
a.)
Applicability.
This Section applies to discharges
resulting from
the production
of asphalt roofing
materials.
79.574

—229—
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 443.31
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
These sources shall
comply with the
general and
specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 443.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 10,
1975.
(Source:
Added
at 11
Ill.
Reg.
effective
)
Section 307.5304
Linoleum and Printed Asphalt Felt
a)
Applicability.
This Section applies
to discharges
resulting from the production of linoleum and printed
asphalt felt floor coverings.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 443.41
(1986).
This incorporation
includes no
later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 443.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POT~Jin violation of such
standards.
79-575

—230—
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced after January 10,
1975.
(Source:
Added
a.t
11
Ill. Req.
effective
)
SUBPART BU:
PAINT FORMULATING
Section 307.5601
Oil—Base Solvent Wash Paint
a)
Applicability.
This Section applies
to discharges
resulting from the production of oil—base paint where
the
tank cleaning
is performed using solvents.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 446.11
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates
by
reference
40 CFR 446.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No
person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
commenced after February 26,
1975.
(Source:
Added
a.t
11
Ill.
Req.
effective
)
SUBPART BV:
INK FORMULATING
Section 307.5701
Oil—Base Solvent Wash
Ink
a)
Applicability.
This Section applies
to discharges
resulting
from
the
production
of
oil—base
ink
where
the
tank washing
system uses solvents.
b)
Specialized
definitions.
The
Board
incorporates
by
reference 40 CFR 447.11
(1986).
This incorporation
includes no later amendments or editions.
79-576

—231—
C)
Existing sources:
These sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 447.16
(1986).
This incorporation includes no later
amendments
or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POT~ in
violation
of
such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
February 26,
1975.
(Source:
Added
at
11
Ill. Req.
,
effective
SUBPART CD:
PESTICIDE CHEMICALS
Section 307.6500
General Provisions
General definitions.
The Board incorporates by reference
40 CFR
455.10
(1986),
as amended at
51 Fed.
Reg.
44911,
December
15,
1986.
This incorporation includes no later
amendments
or
editions.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.6501
Organic Pesticide Chemicals Manufacturing
a)
Applicability.
U
The Board
incorporates by reference 40 CFR 455.20
(1986),
as amended
at
51 Fed.
Reg.
44911,
December
15,
1986.
This incorporation includes no later
amendments
or editions.
2)
This Section applies
to discharges resulting from
any plant which manufactures organic pesticide
chemicals,
as defined
in the materials incorporated
by reference
in subsection
(a)(l).
b)
Specialized
definitions.
The
Board
incorporates
by
reference
40 CFR 455.21
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing
sources:
These
sources
shall
comply
with
the
79.577

—232—
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at 11
Ill. Reg.
effective
Section 307.6502
Metallo—Or~anicPesticides Chemicals
Manufacturing
a)
Applicability.
This Section applies to discharges
resulting from the manufacture of metallo—organic active
ingredients containing mercury,
cadmium, arsenic
or
copper.
The manufacture of the intermediates used to
manufacture the active
ingredients are excluded
from
this Section.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 455.31
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing
sources:
These
sources
shall
comply
with
the
general and specific pretreatment requirements
of
Subpart
B.
ci)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added
at
11
Ill.
Req.
effective
Section 307.6503
Pesticide Chemicals Formulating
and Packaging
a)
Applicability.
This
Section
applies
to
discharges
resulting from all pesticide
formulating and packaging
operations.
b)
Specialized definitions.
None.
c)
Existing
sources:
These
sources
shall
comply
with
the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
All sources are regulated
as existing
sources.
(Source:
Added at 11
Ill.
Req.
effective
SUBPART CG:
CARBON BLACK MANUFACTURING
Section 307.6801
Carbon Black Furnace Process
79-578

—233—
a)
Applicability.
This Section applies
to discharges
resulting from production of carbon black by the furnace
process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 458.11
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
These sources shall
comply with the
general and
specific pretreatment requirements of
Subpart
B.
d)
New
sources:
1)
The
Board
incorporates
by
reference
40
CFR
458.16
(1986).
This incorporation includes
no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or
installation the construction of which
commenced after May 18,
1976.
(Source:
Added at
11 Ill. Req.
effective
Section 307.6802
Carbon Black Thermal Process
a)
Applicability.
This Section applies to discharges
resulting from the production of carbon black by the
thermal process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 458.21
(1986).
This incorporation
includes
no
later
amendments
or
editions.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The
Board
incorporates
by
reference
40
CFR
458.26
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
79-579

—234—
cause,
threaten or allow
the discharge of any
contaminant
to a POTW in violation
of
such
standards.
3)
“New source” means any building, structure,
facility or
installation
the construction of which
commenced after May 18,
1976.
(Source:
Added
a.t
11
Ill. Reg.
effective
)
Section 307.6803
Carbon Black Channel Process
a)
Applicability.
This Section applies
to discharges
resulting from the production of carbon black by the
channel process.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 458.31
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
These
sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
U
The Board
incorporates by reference
40 CFR 458.36
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after May 18,
1976.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.6804
Carbon Black Lamp Process
a)
Applicability.
This Section applies to discharges
resulting from the production of carbon black by the
lamp process.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 458.41
(1986).
This incorporation
includes no
later amendments
or
editions.
79-580

—235—
c)
Existing
sources:
These sources shall comply with the
general and
specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board incorporates by reference 40 CFR 458.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after May 18,
1976.
(Source:
Added
at
11 Ill.
Req.
effective
SUBPART CJ:
BATTERY MANUFACTURING
Section 307.7100
General Provisions
a)
Applicability.
This Subpart applies
to any battery
manufacturing plant which introduces or may introduce
process wastewater pollutants into
a POTW.
Battery
manufacturing operations regulated under this Subpart
are not subject to Subparts N or
AU.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 461.2
(1986).
This incorporation
includes no later amendments or editions.
C)
Monitoring requirements.
The Board
incorporates by
reference
40 CFR 461.3
(1986).
This incorporation
includes no later amendments or editions.
ci)
Compliance dates.
The Board
incorporates by reference
40 CFR 461.4
(1986).
This incorporation includes no
later
amendments or
editions.
(Source:
Added
at 11
Ill.
Req.
effective
)
Section 307.7101
Cadmium
a)
Applicability.
This Section applies
to discharges
resulting from the manufacturing
of cadmium anode
batteries.
79.581

—236—
b)
Specialized definitions.
None.
C)
Existing sources:
1)
The Board incorporates
by
reference
40 CFR 461.14
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
ci)
New sources:
U
The Board incorporates
by
reference
40 CFR 461.15
(1986).
This incorporation includes
no later
amendments or editions.
2)
No
person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
commenced after November
10,
1982.
(Source:
Added at
11
Ill.
Req.
,
effective
)
Section 307.7102
Calcium
a)
Applicability.
This
Section
applies
to
discharges
resulting from manufacturing calcium anode batteries.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with
the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board incorporates by reference
40 CFR 461.25
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
Cl)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
79-582

—237—
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
10,
1982.
(Source:
Added
at
11
Ill.
Reg.
effective
)
Section 307.7103
Lead
a)
Applicability.
This Section applies
to discharges
resulting from the manufacturing
of lead anode
batteries.
b)
Specialized definitions.
None._
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 461.34
(1986),
as amended
at
51 Fed. Req. 30816, August
28,
1986.
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 461.35
(1986),
as amended at
51 Fed. Req.
30816, August
28,
1986.
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced
after November
10, 1982.
(Source:
Added
a.t
11 Ill. Reg.
effective
Section 307.7104
Leclanche
a)
Applicability.
This Section applies to discharges
resulting from manufacturing Leclanche type batteries
79.583

—238—
(zinc anode batteries with acid electrolyte).
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 461.44
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates
by
reference
40 CFR 461.45
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced
after November
10,
1982.
(Source:
Added
a.t 11
Ill.
Req.
effective
Section 307.7105
Lithium
a)
Applicability.
This Section applies
to discharges
resulting from the manufacturing
of lithium anode
batteries.
b)
Specialized definitions.
None.
c)
Existing sources:
These sources shall comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 461.55
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
79-584

—239—
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction
of which
commenced after November
10,
1982.
(Source:
Added
at
11
Ill. Req.
effective
)
Section 307.7106
Magnesium
a)
Applicability.
This Section applies
to discharges
resulting from the manufacturing of magnesium anode
batteries.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board incorporates by reference 40 CFR 461.64
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board incorporates by reference
40 CFR 461.65
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
10,
1982.
(Source:
Added
a.t 11
Ill.
Req.
effective
Section 307.7107
Zinc
a)
Applicability.
This Section applies
to discharges
79.585

—240—
resulting from the manufacturing
of zinc anode
batter ies.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 461.74
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated
by reference in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to a POTW
in violation of such
standards.
ci)
New sources:
U
The Board incorporates by reference
40 CFR 461.75
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
~j
“New source” means any building, structure,
facility or
installation the construction of which
commenced after November
10, 1982.
(Source:
Added
at
11
Ill. Req.
effective
SUBPART CL:
PLASTICS MOLDING AND FORMING
Section 307.7300
General Provisions
a)
Applicability.
U
This Subpart applies
to any plastics molding and
forming process which introduces or may introduce
process wastewater pollutants into
a POTW.
Plastics molding and forming processes include
processes which blend, mold,
form
or otherwise
process plastic materials into intermediate or
final plastic products.
They include commonly
recognized processes such as extrusion, molding,
coating and laminating
thermoforming, calendering,
casting,
foaming cleaning and finishing.
2)
Plastics molding and
forming processes
(e.g.,
79-586

—241—
extrusion and pelletizin,g)
used by plastics resin
manufacturers
to process crude intermediate plastic
material
for shipment off—site are excluded from
this regulation
and regulated under
the organic
chemicals, plastics and synthetic fibers
category.
Plastics molding and forming processes
used by plastic resin manufacturers
to process
crude
intermediate plastic materials,
which are
further processed on—site
into intermediate or
final plastics products
in molding and forming
processes, are controlled by this Subpart.
3)
Processes that coat
a plastic material onto
a
substrate may fall within the definition
of
electroplating and metal finished
as defined
in
Subparts N or AU.
These coating processes
are
excluded from the electroplating and metal
finishing point source categories and are subject
to this Subpart.
4)
Coating of plastic material onto
a formed metal
substrate
is also covered by this Subpart and
is
not covered by the
specific metal
forming
guidelines such as aluminum forming, copper
forming
and nonferrous metals forming
(Subparts BP,
BQ,
and,
BT).
This Subpart applies only to
the coating
process;
the metal forming operations are subject
to the specific metal
forming regulation.
5)
Research and development laboratories that produce
plastic products using
a plastics molding and
forming process are subject
to this Subpart if the
plastics molding and
forming process discharges
process water.
The mass of plastic product
produced
in the plastics molding
and forming
process
is not considered when determining
the
applicability of this Subpart
to plastics molding
and forming processes at research and development
laboratories.
6)
Chemical and thermal reticulation processes for
polyurethane foam are not subject
to this
Subpart.
Water
used
in those processes is not
considered
to be process water
as defined
in this
regulation.
Processes used to further mold
or
form
the reticulated foam are subject, however,
to
this
regulation if they discharge process water.
7)
Processes used
to regenerate cellulose and
to
produce
a product
(e.g.,
rayon)
from the
regenerated cellulose are not subject
to
the
limitations and standards
in
this Subpart.
Processes that mold
or form cellulose derivatives
(e.g.,
cellulose acetate)
are subject
to this
79.587

—242—
Subpart
if they discharge process water.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 463.2
(1986).
This incorporation
includes no later
amendments or editions.
C)
Monitoring requirements.
The Board
incorporates by
reference 40 CFR 463.3
(1986).
This incorporation
includes no later amendments
or editions.
(Source:
Added at
11
Ill. Reg.
effective
)
Section 307.7301
Contact Cooling
and Heating Water
a)
Applicability.
This Section applies to introduction
into POTWs of pollutants resulting
from processes in the
contact cooling and heating water subcategory.
Processes
in the contact cooling
and heating water
subcategory are processes where process water comes
in
contact with plastic materials or plastic products
for
the purpose of heat transfer during plastics molding and
forming.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 463.11
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 463.15
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow
the discharge of any
contaminant to
a POTW in violation of
such
standards.
ci)
New sources:
U
The Board
incorporates
by
reference
40 CFR 463.16
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
fncorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
79-588

—243—
commenced after February 15, 1984.
(Source:
Added at
11 Ill.
Req.
effective
Section 307.7302
Cleaning Water
a)
Applicability.
TThis Section applies
to introduction
into POTW5 of pollutants resulting
from processes in the
cleaning water
subcategory.
Processes
in the cleaning
water__subcategory are processes where water comes
in
contact with the plastic product for the purpose of
cleaning the surface of the product and where water
comes
in contact with shaping equipment, such
as molds
and mandrels,
that contact the plastic material for
the
purpose of cleaning the equipment surfaces.
b)
Specialized definitions.
The Board incorporates by
reference
40 CFR 463.21
(1986).
This incorporation
includes no later
amendments or editions.
c)
Existing sources:
U
The Board
incorporates by reference 40 CFR 463.25
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 463.26
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten
or allow the discharge of any
contaminant
to
a P0Th in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after February 15,
1984.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.7303
Finishing Water
79-589

—244—
a)
Applicability.
This Section applies to introduction
into POTWs of pollutants resulting from processes in the
finishing water
subcategory.
Processes
in the finishing
water
subcategory are processes where water
comes
in
contact with the plastic product during finishing.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 463.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing
sources:
U
The Board
incorporates by reference
40 CFR 463.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
ci)
New sources:
U
The Board
incorporates by reference
40 CFR 463.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
February 15,
1984.
(Source:
Added at
11
Ill. Req.
effective
)
SUBPART CM:
METAL MOLDING AND CASTING
Section 307.7400
General Provisions
a)
Applicability.
This Subpart applies to metal molding
and casting facilities which introduce or may introduce
process wastewater
pollutants into a POTW.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 464.02
(1986).
This incorporation
includes no later
amendments or editions.
c)
Monitoring
requirements.
The Board incorporates by
79-590

—245—
reference 40 CFR 464.03
(1986).
This incorporation
includes no later amendments or editions.
d)
Compliance dates.
The Board incorporates by reference
40 CFR 464.04
(1986).
This incorporation includes no
later
amendments or editions.
(Source:
Added
a.t
11
Ill. Reg.
,
effective
)
Section 307.7401
Aluminum Casting
a)
Applicability.
This Section applies to discharges
resulting from aluminum casting operations,
as defined
in 40 CFR 464.02.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 464.11
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
U
The Board incorporates by reference 40 CFR 464.15
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
ci.)
New sources:
1)
The Board
incorporates by reference
40 CFR 464.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of
which
commenced after November
15,
1982.
(Source:
Added
at 11
Ill.
Req.
effective
)
Section 307.7402
Copper Casting
a)
Applicability.
This Section applies
to discharges
79.591

—246—
resulting from copper casting operations.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFR 464.21
(1986).
This incorporation
includes no later amendments or editions.
C)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 464.25
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of
such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 464.26
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or installation the construction of which
commenced after November
15,
1982.
(Source:
Added
at
11
Ill.
Req.
effective
)
Section 307.7403
Ferrous Casting
a)
Applicability.
This Section applies
to discharges
resulting from ferrous
casting operations.
b)
Specialized definitions.
The
Board incorporates by
reference 40 CFR 464.31
(1986).
This incorporation
includes
no later amendments or editions.
C)
Existing sources:
1)
The Board
incorporates
by
reference
40 CFR 464.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
79-592

—247—
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 464.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after November
15,
1982.
(Source:
Added
at
11
Ill.
Reg.
,
effective
)
Section 307.7404
Zinc Casting
a)
Applicability.
This Section applies to discharges
resulting from zinc casting
operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 464.41
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
U
The Board incorporates by reference
40 CFR 464.45
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board incorporates by reference
40 CFR 464.46
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
79.593

—248—
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
15,
1982.
(Source:
Added
at 11
Ill.
Reg.
effective
SUBPART CN:
COIL COATING
Section 307.7500
General Provisions
a)
Applicability.
This Subpart applies to any coil coating
facility or
to any canmaking facility which introduces
or may introduce process wastewater pollutants into
a
POTW.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 465.02
(1986).
This incorporation
includes
no later
amendments or
editions.
C)
Monitoring requirements.
The Board incorporates by
reference 40 CFR 465.03
(1986).
This incorporation
includes
no later amendments
or editions.
ci)
Compliance dates.
The Board
incorporates by reference
40 CFR 465.04
(1986).
This incorporation includes
no
later
amendments or editions.
(Source:
Added
at
11 Ill.
Reg.
effective
Section
307.7501
Steel Basis Material
a)
Applicability.
This Section applies
to discharges
resulting from coil coating
of steel
basis material
coils.
b)
Specialized definitions.
None.
c)
Existing sources:
U
The Board
incorporates by reference
40 CFR 465.14
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
79-594

—249—
1)
The Board incorporates by reference
40 CFR 465.15
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
January 12,
1981.
(Source:
Added
at 11
Ill.
Reg.
effective
Section 307.7502
Galvanized Basis Material
a)
Applicability.
This Section applies to discharges
resulting from coil coating of galvanized basis material
coils.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 465.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board incorporates by reference
40 CFR 465.25
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(I)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source”
means any building,
structure,
facility or installation the construction of which
commenced after
January 12,
1981.
79-595

—250—
(Source:
Added
at
11
Ill. Beg.
effective
Section 307.7503
Aluminum Basis Material
a)
Applicability.
This Section applies
to discharges
resulting
from coil coating of aluminum basis material
coils.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference
40 CFR 465.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 465.35
(1986).
This incorporation includes
no
later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation
of such
standards.
~j
“New source” means any building, structure,
facility or installation
the construction of which
commenced after
January 12,
1981.
(Source:
Added
at
11
Ill.
Reg.
effective
Section 307.7504
Canmaking
a)
Applicability.
This Section applies
to discharges
resulting from the manufacturing
of seamless can bodies,
which are washed.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFR 465.44
(1986).
This incorporation includes no later
79-596

—251—
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
jj
The Board
incorporates by reference
40 CFR 465.45
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten
or allow
the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after
February
10,
1983.
(Source:
Added
at
11
Ill. Beg.
effective
SUBPART
CC:
PORCELAIN ENAMELING
Section 307.7600
General
Provisions
a)
Applicability.
1)
Except
as provided
in
subsections
(a)(2)
or
(a)(3),
this Subpart applies to any porcelain enameling
facility which
introduces or may introduce process
wastewater pollutants
into
a POTW.
2)
Any existing porcelain enameling facility which
prepares
or coats
less than 1600 square meters per
day and which introduces less than 60,000 liters
per day of wastewater
into
a POTW is not controlled
by the pretreatment standards for existing sources
in this Subpart.
These sources shall
comply with
the general and specific pretreatment requirements
of Subpart
B.
3)
This Subpart does not apply to porcelain enameling
on precious metal
basis material.
b)
General definitions.
The Board
incorporates by
reference 40 CFR 466.02
(l~86). This incorporation
includes no later amendments
or editions.
79-597

—252—
c)
Monitoring requirements.
The Board
incorporates by
reference 40 CFB 466.03
(1986).
This incorporation
includes no later amendments
or editions.
ci)
Compliance dates.
The Board incorporates by reference
40 CFR 466.04
(1986).
This incorporation includes no
later amendments or editions.
(Source:
Added
at
11 Ill.
Reg.
effective
)
Section 307.7601
Steel
Basis Material
a)
Applicability.
This Section applies
to dischar~es
resulting from porcelain enameling on steel
basis
materials.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 466.14
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 466.15
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced
after January 27,
1981.
(Source:
Added
at
11 Ill.
Peg.
effective
Section 307.7602
Cast Iron Basis Material
a)
Applicability.
This Section applies
to discharges
resulting from porcelain enameling
of cast iron basis
79.598

—253—
materials.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFB 466.24
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFB 466.25
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow
the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation
the construction of which
commenced after
January 27,
1981.
(Source:
Added
at
11 Ill.
Req.
,
effective
)
Section 307.7603
Aluminum Basis Material
a)
Applicability.
This Section applies
to discharges
resulting from porcelain enameling
of aluminum basis
materials.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board incorporates by reference 40 CFR 466.34
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a P0Th
in violation of such
standards.
79-599

—254—
ci)
New sources:
1)
The Board
incorporates by reference
40 CFB 466.35
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after January 27,
1981.
(Source:
Added
at
11
Ill. Beg.
,
effective
)
Section 307.7604
Copper Basis Material
a)
Applicability.
This Section applies to discharges
resulting from porcelain enameling
of copper basis
materials.
b)
Specialized definitions.
None.
C)
Existing sources:
These
sources shall
comply with the
general and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 466.45
(1986).
This incorporation includes
no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
January 27,
1981.
(Source:
Added
at
11
Ill.
Beg.
,
effective
)
SUBPAB’I
CP:
ALUMINUM FORMING
Section 307.7700
General
Provisions
79-600

—255—
a)
Applicability.
1)
Aluminum forming
includes commonly recognized
forniin9 operations such as rolling, drawing,
extruding and
forging,
and related operations such
as heat treatment,
casting and surface
treatments.
Surface treatment of aluminum
is any
chemical
or electrochemnical
treatment applied
to
the
surface
of aluminum.
Such surface treatment
is
considered
to be
a part of aluminum forming
whenever
it is performed as
an
integral part of
aluminum forming.
For the purposes of
this
Subpart, surface treatment of aluminum
is
considered
to be
an integral part of aluminum
forming whenever
it
is performed
at the
same plant
site
at which aluminum
is formed
and such
operations
are not considered
for regulation under
the electroplating
and metal
finishing provisions
of Subparts N and AH.
Casting aluminum when
performed
as
an
integral part of aluminum
forming
and located
on—site
at
an aluminum
forming plant
is
considered
an aluminum forming operation and
is
covered under
this Subpart.
When aluminum forming
is performed on
the
same site
as primary aluminum
reduction
the casting
shall
be regulated by Subpart
CT (nonferrous metals)
if there
is no cooling
of
the aluminum prior
to casting.
If the aluminum
is
cooled
prior
to casting
then the casting shall
be
regulated
by this Subpart.
2)
This Subpart applies
to any aluminum forming
facility, except
for plants identified
under
subsection
(a)(3), which introduces or may
introduce pollutants into
a POTW.
3)
This Subpart applies
to
indirect discharging
aluminum
forming plants that extrude less than
3
million pounds of product per year and draw, with
emulsions
or
soaps, less than
1 million pounds per
year.
b)
General definitions.
The Board
incorporates by
reference
40 CFR 467.02
(1986).
This incorporation
includes
no later
amendments or editions.
c)
Monitoring
requirements.
The Board
incorporates by
reference
40 CFR 467.03
(1986).
This incorporation
includes no later
amendments or editions.
d)
Compliance dates.
The Board
incorporates by reference
40 CFB 467.04
(1986).
This incorporation includes
no
later amendments
or editions.
79.601

—256—
(Source:
Added
at
11
Ill.
Beg.
effective
)
Section 307.7701
Polling With Neat Oils
a)
Applicability.
This Section applies
to discharges
resulting from the core
and
the ancillary operations of
the rolling with neat oils subcategory.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFB 467.11
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 467.15
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(I)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board incorporates by reference 40 CFP 467.16
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation
the construction of which
commenced after November
22,
1982.
(Source:
Added
at
11
Ill.
Beg.
effective
)
Section 307.7702
Rolling With Emulsions
a)
Applicability.
This Section applies to discharges
resulting from the core and
the ancillary operations of
the rolling with emulsions subcategory.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 467.21
(1986).
This incorporation
includes no later
amendments
or editions.
79.602

—257—
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFB 467.25
(1986).
This
incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board incorporates by reference
40 CFR 467.26
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after November
22,
1982.
(Source:
Added
at
11
Ill.
Beg.
effective
Section 307.7703
Extrusion
a)
Applicability.
This Section applies
to discharges
resulting from the core and
the ancillary operations of
the extrusion subcategory.
b)
Specialized definitions.
The
Board
incorporates by
reference
40 CFR 467.31
(1986).
This incorporation
includes no later amendments or editions.
c)
Existing sources:
.)
The Board
incorporates by reference
40 CFR 467.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(I)
shall
cause, threaten
or allow the discharge of any
contaminant to
a
POTW
in violation of such
standards.
ci)
New sources:
79-603

—258—
1)
The Board
incorporates
by
reference 40 CFR 467.36
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
commenced
after
November
22,
1982.
(Source:
Added
at 11
Ill.
Peg.
effective
)
Section
307.7704
Forging
a)
Applicability.
This
Section
applies
to
discharges
resulting from the core of
the forging subcategory and
the
ancillary
operations.
b)
!pecialized
definitions.
The
Board
incorporates
by
reference 40 CFR 467.41
(1986).
This incorporation
includes no later amendments or
editions.
c)
Existing
sources:
1)
The Board
incorporates by reference 40 CFR 467.45
(1986).
This incorporation includes no later
amendments or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated
by
reference
in
subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New
sources:
1)
The
Board
incorporates
by
reference
40
CFR
467.46
(1986).
This
incorporation
includes
no
later
amendments
or
editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated
by
reference
in
subsection
(1)
shall
cause,
threaten
or
allow
the
discharge
of
any
contaminant
to
a POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
79.604

—259—
commenced after November 22,
1982.
(Source:
Added at
11
Ill. Peg.
effective
)
Section 307.7705
Drawing With Neat Oils
a)
Applicability.
This Section applies to discharges
resulting from the core of the drawing with neat oils
subcategory and
the ancillary operations.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 467.51
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFB 467.55
(1986).
This incorporation includes no later
amendments or editions.
2)
No
person
subject to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFP 467.56
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building,
structure,
facility or installation the construction of which
commenced after November
22,
1982.
(Source:
Added
at
11 Ill.
Peg.
effective
)
Section 307.7706
Drawing With Emulsions or Soaps
a)
Applicability.
This Section applies
to discharges
resulting
from the core and the ancillary operations of
the drawing with emulsions
or
soaps subcategory.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFR 467.61
(1986).
This incorporation
79.605

—260—
includes no later
amendments or editions.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFB 467.65
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 467.66
(1986).
This incorporation includes no
later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced after
November
22,
1982.
(Source:
Added at
11 Ill. Reg.
effective
)
SUBPART CQ:
COPPER FORMING
Section 307.7800
General Provisions
a)
Applicability.
1)
This Subpart applies to discharges
resulting from
the manufacture of formed cop~erand copper alloy
products.
The forming operations covered are hot
rolling, cold rolling, drawing, extrusion and
forging.
This Subpart does not regulate the
forming of precious metals.
(See Subpart CT).
The
casting of copper and copper alloys
is not covered
by this Subpart.
(See Subpart CM).
2)
The discharge allowance for drawing
spent lubricant
of
40 CFR 468.14(c)
and 468.15(c) are applicable
only to those plants that actually discharge the
drawing spent lubricant waste
stream at copper
forming sites.
No discharge allowance is
79-606

—261—
applicable or allowable where
these wastewaters are
hauled off—site
for disposal
or
are otherwise not
discharged
at copper forming sites.
b)
General definitions.
The Board incorporates by
reference
40 CFR 468.02
(1986).
This incorporation
includes
no later amendments or
editions.
c)
Monitoring requirements.
The Board
incorporates by
reference
40 CFR 468.03
(1986).
This incorporation
includes no later amendments or editions.
ci)
Compliance dates.
The Board
incorporates by reference
40 CFR 468.04
(1986).
This incorporation includes no
later amendments or
editions.
(Source:
Added
at
11
Ill.
Beg.
effective
)
Section 307.7801
Copper Forming
a)
Applicability.
This Section applies to discharges
resulting from the
forming
of copper
and copper
alloys
except beryllium copper
alloys.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFB 468.14
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFR 468.15
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
~J
“New source”
means any building, structure,
facility or
installation the construction of which
commenced after November
12,
1982.
79-607

—262—
(Source:
Added
at
11
Ill.
Beg.
effective
)
Section 307.7402
Beryllium Copper
Forming
a)
Applicability.
This Section applies
to discharges
resulting from the forming of beryllium copper alloys.
b)
Specialized
definitions.
None.
c)
Existing sources:
These sources shall
comply with the
general
and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
All sources are regulated as existing
sources.
(Source:
Added
at
11
Ill.
Beg.
effective
)
SUBPART CR:
ELECTRICAL AND ELECTRONIC COMPONENTS
Section 307.7901
Semiconductor
a)
Applicability.
This Section
applies to discharges
resulting from all
process operations associated with
the manufacture of semiconductors, except sputtering,
vapor deposition
and electroplating.
b)
Specialized definitions.
The Board
incorporates by
reference
40 CFB 469.12
(1986).
This incorporation
includes no later
amendments
or editions.
C)
Existing sources:
1)
The Board incorporates by reference 40 CFP 469.16
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference 40 CFB 469.18
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference in subsection
(I)
shall
79-608

—263—
cause,
threaten
or
allow the discharge of any
contaminant
to
a
POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
commenced
after
August
8,
1982.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section 307.7902
Electronic Crystals
a)
Applicability.
This Section applies
to discharges
resulting from
the manufacture of electronic crystals.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFB 469.22
(1986).
This incorporation
includes
no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 469.26
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
Tncorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFR 469.28
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person
subject to the pretreatment standards
incorporated by reference
in subsection
(I)
shall
cause, threaten or allow the discharge of any
contaminant to
a P0Th
in violation of
such
standards.
3)
“New source” means any building, structure,
facility or installation the construction of which
commenced
after August
8,
1982.
(Source:
Added
at
11
Ill.
Beg.
effective
)
Section 307.7903
Cathode Ray Tube
a)
Applicability.
This Section applies
to discharges
79.609

—264—
resulting
from the manufacture of cathode ray tubes.
b)
Specialized definitions.
The Board
incorporates by
reference 40 CFR 469.31
(1986).
This incorporation
includes no later amendments
or editions.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 469.34
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFP 469.36
11986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
March
9,
1983.
(Source:
Added
at
11 Ill. Beg.
effective
Section 307.7904
Luminescent Materials
a)
Applicability.
This
Section
applies
to
discharges
resulting
from
the
manufacture
of
luminescent
materials.
b)
Specialized definitions.
The Board incorporates by
reference 40 CFP 469.41
(1986).
This incorporation
includes no later
amendments or
editions.
c)
Existing sources:
These sources shall comply with the
general
and specific pretreatment requirements of
Subpart
B.
ci)
New sources:
1)
The Board
incorporates by reference
40 CFB
469.43
(1986).
This incorporation includes
no later
79-610

—2 65—
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in
subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after March
9,
1983.
(Source:
Added
at 11
Ill.
Reg.
effective
)
SUBPART CT:
NONFERROUS METALS FORMING AND METAL POWDERS
Section 307.8100
General
Provisions
a)
Applicability.
1)
This Subpart applies
to the introduction of
pollutants into
a POTW from the forming of
nonferrous metals
(including nonferrous
metal
alloys), except beryllium, copper
and
aluminum, and
their alloys.
Aluminum alloys are defined
as any
alloy in which aluminum
is the major constituent in
percent by weight.
Copper are defined
as any alloy
in which copper
is the major constituent
in percent
by weight except when copper
is alloyed with
precious
metals.
Any
copper—precious
metal
alloy
containing
30
percent
or
greater
precious
metal
is
considered
a
precious
metal
alloy
for
the
purpose
of this subpart.
Beryllium alloys are any alloy
in
which beryllium
is present at 0.1 percent or
greater.
This subpart applies
to:
A)
Forming operations,
including rolling (both
hot and cold), extruding
forging, drawing,
swaging, cladding and
tube reducing, and
B)
Ancillary operations performed
as an integral
part of the
forming
of these metals,
including
casting
for subsequent forming, heat
treatment,
surface treatment, alkaline
cleaning, solvent degreasi9, product testing,
surface coating,
sawing, grinding, tumbling,
burnishing
and wet air pollution control.
2)
This subpart also applies
to
introduction of
pollutants into
a POTW from mechanical metal powder
production operations, forming
of parts from metal
powders, and
associated ancillary operations of:
79-611

—2 66—
A)
Iron, copper
and aluminum and their alloys;
and
B)
The nonferrous metal
and their alloys
described
in subsection(a)(l).
This subpart
does not regulate the production of metal
powders by chemical means such as
precipitation.
The production of metal powder
as the final
step in refining metal
is
regulated under
nonferrous metals
manufacturing, Subpart
V.
3)
Surface
treatment
includes
any
chemical
or
electrocheinical
treatment
applied
to
the
surface
of
the
metal.
For
the
purposes
of
this
subpart,
surface treatment of metals
is considered
to be
an
integral part of the forming
of metals whenever
it
is perfomred at the same plant site
at which the
metals are formed.
Such surface treatment
operations are not regulated under
the
electroplating or metal
finishing regulations,
subparts
N or
AH.
4)
Casting
is covered by this subpart when
it
is
performed
as an
integral part of the metal forming
process and takes place
at the same plant site at
which metals are formed.
Such casting
is not
regulated
under
the provisions of metal molding
and
casting
(Subpart CM).
5)
This subpart does not apply to the formin9 of the
metals cadmium, chromium, gallium, germanium,
indium,
lithium, manganese,
neodymium or
praseodymium.
b)
General
definitions.
The
Board
incorporates
by
reference
40
CFR
471.02
(1986).
This incorporation
includes_no_later amendments or editions.
c)
Compliance dates.
The
Board
incorporates by reference
40 CFR 471.03
(1986).
This incorporation includes no
later amendments or
editions.
(Source:
Added
at
11
Ill. Peg.
effective
Section
307.8101
Lead—Tin—Bismuth
Forming
a)
Applicability.
This Section applies to discharges
resulting
from
the
process
operations
of
the
lead—tin
bismuth
forming
subcategory.
b)
Specialized
definitions.
None.
79-612

—2 67—
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 471.14
(1986).
This
incorporation
includes
no
later
amendments
or
editions.
2)
No
person
subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 471.15
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced
after March
5,
1984.
(Source:
Added
at
11 Ill. Reg.
effective
)
Section 307.8102
Magnesium Forming
a)
Applicability.
This Section applies
to discharges
resulting
from
the process operations of the magnesium
forming subcategory.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates b~reference
40 CFP
471.24
(1986).
This incorporation includes
no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in
subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New
sources:
1)
The Board
incorporates by reference
40 CFF 471.25
79-613

—2 68—
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New
source”
means
an~~
building,
structure,
facility or
installation the construction of which
commenced
after March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section 307.8103
Nickel—Cobalt Forming
a)
Applicability.
This Section applies to discharges
resulting
from
the
process
operations
of
the
nickel—
cobalt
forming
subcategory.
b)
Specialized
definitions.
None.
c)
Existin2
sources:
1)
The Board
incorporates by reference 40 CFB
471.34
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates b~reference 40 CFR 471.35
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
~faci1ityor
installation the construction of which
commenced after March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
79.614

—269—
Section 307.8104
Precious Metals Forming
a)
Applicability.
This Section applies
to discharges
resulting
from the process operations of
the precious
metals forming subcategory.
b)
Specialized
definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates
by
reference
40
CFP
471.44
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFP 471.45
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause,
threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility
or
installation
the
construction
of
which
commenced
after
March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section
307.8105
Refractory
Metals
Forming
a)
Applicability.
This Section applies to discharges
resulting from
the process operations
of the refractory
metals forming
subcategory.
b)
Specialized
definitions.
None.
c)
Existing
sources:
1)
The
Board
incorporates by reference
40
CFR
471.54
(1986).
This
incorporation
includes
no later
amendments
or editions.
79-615

—270—
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates
by
reference 40 CFR 471.55
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section 307.8106
Titanium
Forming
a)
Applicability.
This Section applies
to discharges
resulting from the process operations
of- the titanium
forming subcategory.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference
40 CFP 471.64
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR
471.65
(1986).
This incorporation includes
no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
79-616

—271—
contaminant
to a POTW
in violation of such
standards.
3)
“New source” means any building, structure,
facility or
installation the construction of which
commenced after
March
5,
1984.
(Source:
Added
at
11 Ill.
Peg.
effective
)
Section 307.8107
Uranium Forming
a)
Applicability.
This Section applies
to discharges
resulting
from the process operations of the uranium
forming subcategory.
b)
Specialized definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates by reference
40 CFR 471.74
(1986).
This incorporation includes no later
amendments or
editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
d)
New
sources:
1)
The Board incorporates by reference
40 CFR 471.75
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New source”
means
drly
building,
structure,
facility or
installation
the
construction
of
which
commenced
after
March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section
307.8108
Zinc
Forming
a)
Applicability.
This
Section
applies to discharges
resulting
from
the
process
operations of the
zinc
forming
subcategory.
79-617

—2 72—
b)
Specialized
definitions.
None.
c)
Existing
sources:
1)
The Board
incorporates
by
reference 40 CFP 471.84
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated
by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a POTW in violation of such
standards.
d)
New
sources:
1)
The
Board
incorporates
by
reference
40
CFR 471.85
(1986).
This
incorporation includes no later
amendments
or editions.
2)
No person subject to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or allow the discharge of any
contaminant
to
a
POTW in violation of such
standards.
3)
“New source” means any building,
structure,
facility or
installation the construction of which
commenced
after March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section 307.8109
Zirconium—Hafnium Forming
a)
Applicability.
This Section applies to discharges
resulting from
the
process operations of the
zirconium—
hafnium forming
subcategory.
b)
Specialized definitions.
None.
c)
Existing sources:
1)
The Board
incorporates by reference 40 CFR 471.94
(1986).
This incorporation includes no later
amendments
or editions.
2)
No person subject
to the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten or
allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
79-618

—273—
d)
New sources:
1)
The Board incorporates by reference
40 CFR 471.95
(1986).
This incorporation includes no later
amendments
or editions.
2)
No
person
subject
to
the
pretreatment
standards
incorporated by reference
in subsection
(1)
shall
cause,
threaten or allow the discharge of any
contaminant to
a POTW in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility
or
installation
the
construction
of
which
commenced after March
5,
1984.
(Source:
Added
at
11
Ill.
Peg.
effective
)
Section 307.8110
Metal
Powders
a)
Applicability.
This Section applies
to discharges
resulting
from the process operations of the metal
powders subcategory.
b)
Specialized definitions.
None.
C)
Existing
sources:
1)
The Board
incorporates by reference
40 CFP
471.104
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject
to
the pretreatment standards
incorporated by reference
in subsection
(1)
shall
cause, threaten
or allow the discharge of any
contaminant
to
a POTW
in violation of such
standards.
d)
New sources:
1)
The Board
incorporates by reference
40 CFR 471.105
(1986).
This incorporation includes no later
amendments or editions.
2)
No person subject to
the pretreatment standards
incorporated by reference
in subsection
(1) shall
cause, threaten or
allow the discharge of any
contaminant to
a POTW
in violation of such
standards.
3)
“New
source”
means
any
building,
structure,
facility or installation the construction of which
commenced after March
5,
1984.
79.619

—274—
(Source:
Added
at
11
Ill.
Peg.
effective
Appendix
References
to
Previous
Rules
(Repealed)
~he ~e~ew4~~g ~eb~e 4s pfeY4~e~4e a~ ~
e~ Bee~
t~i~e
~Uffi~~f
S
4e
eee~en
n~n~erepa~et~e~~e
eeee~ei~
~
We~erPee~#e~
3~r
H~T
A&~~Teeee
Pef~
V~T
~ewe~
B4sehe~e
?~4~e~e
Pef~ 3~
~
P~ee~
e1-~T
See~e~
-~93~
Re~e
TTr
TTTTTTTTrTT~eek~*ef~
39~4&2
Rt*~e
~
~9~-~93
Rt~e
~+TT1~
TT~
TTv~ee~en
~94T~8~
R~e
~TT
TTT~TySee~ot~
38~-~94
Rt*~e ~G4
TTTTTT-~,TSee~±eI~~
-3~95
(Source:
Repealed
at
11
Ill.
Peg.
,
effective
)
79.620

—lB-
TITLE
35 ENVIRONMENTAL PROTECTION
SUBTITLE
C:
WATER
POLLUTION
CHAPTER
I:
POLLUTION
CONTROL
BOARD
PART
309
PERM
ITS
SUBPART A:
NPDES PERMITS
Preamble
NPDES Permit Required
Application
General
Renewal
Authority to Deny NPDES
Permits
Access
to Facilities
and
Further Information
Distribution of Applications
Tentative Determination and Draft Permit
Public Notice
Contents of Public Notice of Application
Combined Notices
Agency Action After Comment Period
Fact Sheets
Notice
to Other Governmental Agencies
Public Hearings on NPDES Permit Applications
Notice of Agency Hearing
Agency Hearing
Agency Hearing File
Agency Action After Hearing
Terms and Conditions of NPDES
Permits
Water Quality Standards and Waste Load Allocation
Effluent Limitations
Federal New Source Standards of Performance
Duration
of
Permits
Authority
to
Establish
Recording,
Reporting,
Monitoring
and Sampling Requirements
Authority to Apply Entry and Inspection Requirements
Schedules
of
Compliance
Authority
to
Require
Notice
of
Introduction
of
Pollutants into Publicly Owned Treatment Works
309.150
Authority to Ensure Compliance by Industrial
Users with
Sections 204(b),
307 and 308 of the Clean Water
Act
Maintenance
and
Equipment
Toxic Pollutants
Deep Well Disposal of Pollutants
(repealed)
Authorization
to Construct
Sewage Sludge Disposal
Total Dissolved Solids Reporting and Monitoring
Appeal
of
Final
Agency
Action
on
a
Permit
Application
Authority to Modify,
Suspend or
Revoke Permits
Revision of Schedule of Compliance
Permit Modification Pursuant
to Variance
Public
Access
to
Information
Effective Date
Section
309.
101
309.102
309.
103
309.104
309. 105
309. 106
309. 107
309. 108
309.
109
309.
110
309.111
309. 112
309.113
309. 114
309.115
309.116
309.117
309. 118
309.119
309.
141
309.142
309. 143
309.144
309.145
309. 146
309. 147
309.148
309.
149
309.
151
309.152
309.
153
309.154
309.
155
309.156
309.
181
309.182
309.
183
309.184
309.
185
309.191
79-621

—2B—
Preamble
Construction
Permits
Operating
Permits;
New
or
Modified
ee~et~ Werks7
Sewefe
em~
Wes~ewe~erSources
309.204
Operating Permits; Existing
ee~,rer~
Weeks-,-
Pee~eee~ffie~
Weeks st~8Wee~ewa~eeSources
Applications
Contents
Applications
Applications
Applications
Applications
Standards
for
Issuance
Duration of Permits Issued Under
Subpart B
Conditions
Appeals from Conditions
in Permits
Permit
No Defense
Design, Operation and Maintenance
Criteria
Modification of Permits
Permit Revocation
Approval of
Federal Permits
Procedures
Effective Date
Severability
Appendix
References
to
Previous
Rules
AUTHORITY:
Authorized
by Section 27 and implementing Section
13
and 13.3 of the Environmental Protection Act as amended by P.A.
84—1320, effective September
4,
1986
(Ill. Rev.
Stat.
1985,
ch.
ill ~/2
,
pars.
1027 and 1013 and
Ill.
Rev.
Stat.
1986 Supp.,
ch.
ill ~/2~par.
1013.3).
SOURCE:
Adopted
in P71—14,
at
4 PCB
3,
March
7,
1972;
amended
in P73—li,
12,
at
14 PCB 661, December
5,
1974, at 16 PCB 511,
April
24,
1975,
and at
28 PCB 509, December
20,
1977;
amended
in
P73—il,
12,
at
29 PCB 477,
at
2
Ill.
Peg.
no.
16, page
20,
effective
April
20,
1978;
amended
in
R79—13,
at
39
PCB
263,
at
4
Ill.
Peg.
no.
34, page 159, effective August
7,
1980;
amended
in
R77—l2B,
at
41 PCB 369, at
5
Ill.
Peg. 6384, effective May 28,
1981;
amended
in P76—21,
at
44 PCB 203, at
6
Ill.
Peg.
563,
effective December 24,
1981;
codified
6
Ill.
Peg.
7818;
amended
in R82—5,
10,
at
54 PCB 411, at
B
Ill.
Peg.
1612, effective
January 18,
1984;
amended
in
P86—44 at
11
Ill.
Reg.
,
-
effective
SUBPART
B:
OTHER
PERMITS
Section
309. 201
309.202
309. 203
SUBPART
B:
OTHER
PERMITS
Joint Construction and Operating Permits
Experimental Permits
Former Permits
(repealed)
Permits
for Sites Receiving
Sludge
for
Land Application
Signatures and Authorizations
Registered
or Certified Mail
Time to Apply
Filing
and Final Action by Agency
309.205
309.206
309. 207
309.208
309. 221
309. 222
309.223
309. 224
309.
225
309.241
309.
242
309.243
309.
244
309. 261
309.
262
309.263
309.
264
309.265
309. 266
309. 281
309. 282
79-622

—3B
-
Section
309.201
Preamble
a)
This
Subpart
B
establishes
basic
rules
for the issuance
of permits
for
the construction, modification
and
operation of treatment works, pretreatment works,
sewers,
wastewater sources and other discharges which
are
not
required
to
have NPDES Permits.
b)
Discharges
for which
a pretreatment permit has been
issued by the Agency,
or
for which
an authorization to
discharge has been
issued
by a publicly owned
treatment
works
(POTW) with
an approved pretreatment program,
pursuant
to 35 Ill. Adm. Code 310, are exempt
from the
operating permit requirement of this Subpart.
However,
such discharges may be subject
to the construction
permit requirement.
(Source:
Amended
at
11
Ill.
Peg.
effective
Section
309.203
Operating
Permits; New or Modified ~eee~e~t
WOekST
Gewece e~Wee~ewe~eeSources
a)
No person shall cause or allow the
use or operation of
any treatment works,
sewer7 or wastewater source
for
which
a construction permit
is required under Section
309.202 without
an operating permit issued by the
Agency, except as may be authorized
by the construction
permit.
b)
No operating permit
is required
under this Section for
any discharge:
1)
F~orwhich an NPDES permit
is reguired~ or
2)
For which
a pretreatment permit has been issued by
the Agency,
or
for which
an authorization
to
discharge has been
issued by a POTW with an
approved pretreatment program, pursuant
to
35 Ill.
Adm.
Code
310.
(Source:
Amended
at
11
Ill.
Peg.
effective
)
Section 309. 204
Operating Permits; Existing
ee4~rei~
Weeksy
Pee~re~ei~
Weeks
e,~ Wee~ewe4ee Sources
a)
No person
shall cause or
allow the use or operation of
any
treatment
works,
pretreatment
works
or
wastewater
source without an operating permit issued by the Agency,
except as provided
in peee~eephesubsections(b),
(c),-
and
(d).
b)
No operating permit
is required under this Section for
79.623

—4B-
any
discharge:
1)
F~orwhich
an NPDES permit
is required;
or
2)
For
which
a
pretreatment
permit
has
been
issued
by
the
Agency,
or
for
which
an
authorization
to
~ischarge has been issued by
a POTW with an
approved pretreatment program, pursuant
to 35 Ill.
Adm.
Code 310.
c)
Operating
permits
are
not required
for treatment works
and
wastewater
sources
that
are
designed
and
intended
to
serve
a
single
building
and
eventually
treat
or
discharge less than an average of 1500 gallons per day
(5700
1/day)
of domestic sewage and which will
discharge,
if
at
all,
directly
to a publicly owned
or
publicly
regulated
sanitary
or
combined
sewer.
d)
Operating permits are not required for those
pretreatment works
or wastewater sources discharging
to
a
sewer
tributary
to
a
treatment
works
which
will
not:
1)
Discharge
toxic
pollutants,
as
defined
in
Section
502(13)
of the
CWA,
or pollutants which may
interfere
with
the
treatment
process
into
the
receiving treatment works or
be subject
to
regulations
promulgated
under
Section
307
of
the
Clean Water
Act (CWA);
or
2)
Discharge
15
or more of the total hydraulic
flow
received
by
the
treatment
works;
or
3)
Discharge 15
or more of the
total biological
loading received by the treatment works as measured
by the 5—day biochemical
oxygen demand.
(Source:
Amended
at
11
Ill.
Peg.
,
effective
79.624

—IC—
TITLE
35:
ENVIRONMENTAL
PROTECTION
SUBTITLE
C:
WATER
POLLUTION
CHAPTER
I:
POLLUTION CONTROL BOARD
PART 310
PRETREATMENT PROGRAMS
SUBPART A:
GENERAL PROVISIONS
Section
310.101
310.102
310. 103
310.104
310. 105
310.107
310.110
310.400
310. 401
310.402
310.403
310.410
310.411
310.412
310.413
310. 414
310. 415
310.420
310.421
310.430
310.431
310.432
310.441
310.442
310.443
310.444
Applicability
Objectives
Federal
Law
State
Law
Confidential ity
Incorporations by Reference
De f in i tions
SUBPART B:
PRETREATMENT STANDARDS
General
Prohibitions
Specific Prohibitions
Specific Limits Developed
by POTW
Local
Limits
Enforcement
Categorical
Standards
Category Determination Request
Deadline
for Compliance with Categorical Standards
Concentration and Mass Limits
Dilution
Combined Wastestreain
Formula
Preamble
Pretreatment Permits
Time
to Apply
Imminent Endangerment
Application
Certification
of
Capacity
Signatures
Site Visit
Completeness
Time Limits
Standard
for
Issuance
Final
Action
Conditions
Duration of Permits
Schedules
of
Compliance
Effect of
a Permit
Modification
Revocation
Appeal
Section
SUBPART E:
POTW PRETREATMENT PROGRAMS
Section
310. 201
310.202
310. 210
310.211
310. 212
310.220
310.221
310.222
310.230
310.232
310.233
SUBPART
D:
PRETREATMENT
PERMITS
79-625

—2C—
310. 501
310.502
310. 503
310.504
310.505
310. 510
310. 521
310.522
310.
531
310.532
310.533
310.
541
310.
542
310. 543
310.
544
310.545
310. 546
310.547
Section
310.601
310.602
310.603
310.604
310.605
310.
606
310. 610
310. 621
310. 631
310.632
310.633
310.634
Pretreatment Programs Required
Deadline
for
Program
Approval
Incorporation of Approved Programs
in Permits
Incorporation of Compliance Schedules
in Permits
Reissuance or Modification of Permits
Pretreatment Program Requirements
Program
Approval
Contents
of
Program
Submission
Agency
Action
Defective Submission
Water
Quality
Management
Deadline for Review
Public
Notice
and
Hearing
Agency Decision
USEPA Objection
Notice of Decision
Public Access
to Submission
Appeal
SUBPART F:
REPORTING REQUIREMENTS
Definition of Control Authority
Baseline Report
Compliance
Schedule
Report on Compliance with Deadline
Periodic Reports on Compliance
Notice of Slug Loading
Monitoring and Analysis
Compliance Schedule
for PCTW’s
Signatory Requirements
for
Industrial
User Reports
Signatory Requirements
for
POTW Reports
Fraud
and False Statements
Recordkeeping Requirements
SUBPART
G:
FUNDAMENTALLY DIFFERENT FACTORS
Definition of Requester
Purpose and
Scope
Criteria
Fundamentally Different Factors
Factors which
are Not Fundamentally Different
More Stringent State
Law
Application Deadline
Contents
of
FDF
Request
Deficient Requests
Public Notice
Agency
Review
of
FDF
Requests
USEPA Review of FDF Requests
Section
310.801
Net/Gross Calculation by USEPA
SUBPART
I:
UPSE’IS
Section
310.701
310.702
310.703
310.
704
310. 705
310.706
310.
711
310.
712
310. 713
310.
714
310. 721
310. 722
SUBPART
H:
ADJUSTMENTS FOR POLLUTANTS
IN INTAKE
79-626

-3C-
Section
310.901
Definition
310.902
Effect of an Upset
310.903
Conditions
Necessary for
an Upset
310.904
Burden of Proof
310.905
Reviewability of Claims of Upset
310.906
User Responsibility
in Case of Upset
AUTHORITY:
Authorized
by and implementing Section
13.3 of the
Environmental Protection Act,
as amended by
P.A.
84—1320,
effective September
4,
1986
(Supp.
to
Ill.
Rev.
Stat.
1985 ch.
Ill
1/2, par. 1013.3).
SOURCE:
Adopted
in P86—44
at
11
Ill.
Beg.
effective
SUBPART A:
GENERAL PPCVISIONS
Section 310.101
Applicability
a)
This Section
is intended
as
a general
guide
to persons
using these rules
and does not supersede more specific
requirements contained
in the body of
the rules.
b)
This Part includes the following provisions:
1)
Requirements for submission
to the Agency of
pretreatment programs by publicly owned treatment
works
(PCTW’s).
(Section 310.501 et seq.)
2)
Requirements with which persons discharging
to
sewers must comply.
(Section 310.201 et seq.)
3)
Reouirements
for
prior approval by the control
authority of certain discharges to
a sewer.
The
control authority may be either:
A)
The POTW pursuant
to
an approved program; or
B)
The Agency
in the absence of
an approved
program.
(Section 330.440 et seq.)
Section
310.102
Objectives
This Part satisfies the requirement
of Section 13.3 of the
Environmental Protection Act (Act)
that the
Board
adopt rules
which are identical
in substance with United States Environmental
Protection Agency
(USEPA) regulations implementing the
pretreatment requirements of the Clean Water
Act.
This Part is
intended:
a)
To prevent
the introduction into POTWs of pollutants
which will
interfere with the operation of the POTW,
or
which will interfere with the use
or disposal
of its
79-627

—4C—
sludge;
b)
To prevent
the
introduction
of
pollutants
into
POTWs
which will pass through
the treatment works or which
will otherwise be incompatible with such works; and
c)
To
improve the opportunities to recycle and reclaim
municipal
and
industrial wastewaters and
sludges.
(Board
Note:
Derived from 40 CFR 403.2
(1986))
Section 310.103
Federal Law
a)
The
Board
intends
that
this
Part
be
identical
in
substance
with
the
pretreatment
requirements
of
the
Clean Water Act and United States Environmental
Protection Agency (USEPA)
regulations at
40 CFB 401
et
seq.
(1986).
b)
This
Part will become effective when USEPA authorizes
the Illinois pretreatment program pursuant to the Clean
Water
Act.
After authorization this Part and
35
Ill.
Adm.
Code 307 will supersede the pretreatment
requirements of the Clean Water
Act and
40 CFB
401
et
seq. as applied
in
Illinois, except that USEPA
will:
1)
Retain
the right
to request information pursuant
to
40 CFP 403.8(f)
(1986); and
2)
Retain
the right
to
inspect and take samples
pursuant to
40 CFR 403.12(1).
c)
This Part shall
not be construed
as exempting any person
from compliance,
prior
to authorization of the Illinois
pretreatment program, with the pretreatment requirements
of the Clean Water
Act,
USEPA regulations and NPDES
permit conditions.
d)
POTW pretreatment programs which have been approved
by
USEPA pursuant
to 40 CFR 403 will be deemed approved
pursuant
to this Part, unless
the Agency determines that
it
is necessary to modify the
POTW pretreatment program
to be consistent with State
law.
1)
The Agency shall notify the PCTW of any such
determination within
60 days after approval of the
program by USEPA,
or within
60 days after
USEPA
authorizes the Illinois pretreatment program,
whichever
is
later.
2)
If
the
Agency
so
notifies
the
POTW,
the
POTW
will
apply for program approval pursuant
to Section
310.501
et
seg.
79-628

—SC—
e)
USEPA’s
access
to
Agency
records
and
information
in
possession of the Agency shall
be governed by the
memorandum of agreement between USEPA
and the Agency,
subject to confidentiality requirements
in
Section
310.105.
Section
310.
104
State
Law
a)
35
Ill. Adm.
Code 307
includes three
types of
prohibitions and pretreatment standards:
1)
Prohibitions, including prohibitions adopted by
tJSEPA at
40 CFR 403.5
and more stringent
prohibitions adopted by the
Board
(35
Ill.
Adni.
Code 307.1101);
2)
National pretreatment standards adopted by USE’PA at
40 CFR 405
et seq.,
and
incorporated by reference
by the Board
(35 Ill.
Adm. Code 307.1501 et seq.);
3)
More stringent concentration—based standards
adopted
by the Board
(35 Ill. Adm. Code 307.1102
and
307.1103).
b)
For subcategories
for which
there are both categorical
pretreatment standards and concentration—based standards
adopted by the Board
for
a pollutant, the control
authority shall apply the standard which
is more
stringent as applied
to the discharge.
(Board
Note:
Derived
from
40 CFR 403.4
(1986))
Section
310.105
Confidentiality
a)
Information
and data provided
to the control authority
pursuant to this Part which
is effluent data
shall
be
available to the public without restriction.
b)
With respect
to the Board
and Agency, confidentiality
shall be governed by 35
Ill.
Adm.
Code 120 and 161.
c)
The Agency and POTW’s
shall make information available
to the public at least
to the extent provided by 40 CFR
2.302
(1986).
(Board
Note:
Derived
from
40
CFR
403.14
(1986))
Section
310.107
Incorporations
by
Reference
a)
The following publication
is incorporated
by referer~ce:
Standard
Industrial Classification Manual
(1972),
and 1977 Supplement, republished
in
1983, available
from
the
Superintendent
of
Documents,
U.S.
79.629

—6C—
Government Printing Office,
Washington,
D.C.
20401.
b)
This Part incorporates no
future editions or
amendments.
Section
310.110
Definitions
“Act”
means
the Environmental Protection Act, as amended
by
P.A.
84—1320,
effective
September
4,
1986
(Ill.
Rev.
Stat.
1985 ch.
111
1/2, par.
1001
et
seq.,
and
Ill. Rev.
Stat.
1986 Supp.,
ch.
lii
1/2, par 1013.3)
“Agency” means the Illinois Environmental Protection
Agency.
“Approval
Authority”
means
the
Agency.
(Board
Note:
Derived
from 40 CFR 403.3(c)
(1986))
“Approved
POTW Pretreatment Program”
or “Program”
or
“PGTW
Pretreatment
Program”
means
a program administered
by
a
PCTW
which
has
been
approved
by
the Agency
in
accordance with Sections 310.540 through 310.546.
(Board Note:
Derived
from 40 CFR
403.3(d)
(1986))
“Authorization
to discharge” means
an authorization
issued
to
a discharger by a POTW which has an
approved
pretreatment program.
The authorization may consist of
a permit, license, ordinance or other mechanism as
specified
in the approved pretreatment program.
“Blowdown” means
the minimum discharge of recirculating
water
for
the
purpose
of
discharging
materials
contained
in
the water,
the further buildup of which would cause
concentration
in amounts exceeding limits established by
best engineering practice.
(Board Note:
Derived from 40 CFR 401.11(p)
(1986))
“Board” means the Illinois Pollution Control Board.
“CWA”
means
Federal Water Pollution Control Act, also
known
as
the
Clean
Water
Act, as amended,
(33 USC 1251,
et
seq.)
(Board Note:
Derived
from 40 CFB 403.3(b)
(1986))
“Control authority”
is as defined
in Section 310.601.
“Indirect Discharge”
or “Discharge” means
the
introduction of pollutants
into
a POTW from any non—
domestic source regulated under Section 307(b),
(c)
or
(c3) of the CWA
(33 USC 1317(b),
(C)
or
(d)).
79-630

—7C—
(Board Note:
Derived from 40 CFR 403.3(g)
(1986))
“Industrial
User”
or
“User” means
a source of indirect
discharge.
(Board Note:
Derived
from 40 CFP 403.3(h)
(1986))
“Industrial wastewater” means waste of
a liquid nature
discharged
by an
industrial user
to
a sewer
tributary to
a POTW.
“Interference” means
a discharge which, alone or
in
conjunction with
a discharge or discharges from other
sources, both:
Inhibits or disrupts the
POTW,
its treatment
processes or operations,
or its
sludge processes,
use
or disposal; and
Therefore
is
a cause of
a violation of any
requirement
of
the
POTW’s
NPDES permit
(including
an
increase
in the magnitude or duration of
a
violation)
or of the prevention of sewage sludge
disposal
in compliance with any of the following
permits or regulations:
35 Ill.
Adm. Code 309.208
(Permits for Sites Receiving
Sludge
for Land
Application), 703.121
(RCRA Permits), 807.202
(Solid Waste Permits), the Toxic Substances Control
Act
(15 USC 2601)
or
the Marine Protection,
Research and Sanctuaries Act
(33 USC 1401).
(Board Note:
Derived from 40 CFR 403.3(i)
(1986),
as amended at
52
Fed.
Peg.
1600, January
14,
1987)
“Municipal
sewage”
is sewage treated by
a POTW exclusive
of
its industrial component.
“Municipal
sludge”
is sludge produced
a POTW treatment
works.
“Municipality.”
See
“unit of local government.”
“New
source”
means
any
building,
structure,
facility
or
installation from which there
is
or may be
a discharge
of pollutants, the construction of which commenced after
the date specified
in 35 Iii.
Adm. Code 307 for that
category or subcategory.
(Board Note:
Derived from 40 CFR 401.11(c)
and 403.3(k)
(1986))
“Noncontact cooling water” means water
used
for cooling
which does not come into direct contact with any raw
79.631

—BC
material, intermediate product, waste product or
finished product.
(Board Note:
Derived
from 40 CFR 401.11(n)
(1986))
“Noncontact cooling water pollutants” means pollutants
present in noncontact cooling waters.
(Board Note:
Derived
from 40 CFR 401.11(o)
(1986))
“NPDES Permit” means
a permit issued
to
a POTW pursuant
to Section 402 of the
CWA,
or Section
12(f)
of the Act
and
35
Ill. Adm. Code 309.Subpart
A.
(Board Note:
Derived
from 40 CFR 403.3(1)
(1986))
“0 and
M” means operation and maintenance.
“Pass through” means
a discharge of pollutants which
exits the POTW into waters of the State
in quantities or
concentrations
which,
alone
or
in
conjunction
with
a
discharge or discharges from other
sources,
is
a cause
of
a violation of any requirement of the POTIc’s NPDES
permit (including
an
increase
in
the magnitude or
duration
of
a
violation).
(Board Note:
Derived
from 40 C??
403.3(n)
(1986),
as
amended
at
52 Fed.
Peg.
1600, January 14,
1987)
“Person” means an
individual, corporation, partnership,
association,
State,
“unit of local government”
or any
interstate body.
This term includes the United
States
government, the State of Illinois and their pclitical
subdivisions.
(Board
Note:
Derived
from
40 CF? 401.11(m)
(1986)
and
33 USC 1362(5))
“Pollutant” means dredged
spoil, solid waste,
incinerator residue,
sewage, garbage,
sewage
sludge,
munitions, chemical wastes, biological materials,
radioactive materials, heat,
wrecked or discarded
equipment,
rock,
sand, cellar dirt and
industrial,
municipal
and agricultural waste discharged
into a
sewer.
(Board Note:
Derived from 40 CFR 401.11(f)
(1986))
“Pollution” means
the man—made or man—induced
alteration
of the chemical, physical, biological
and radiological
integrity of water.
(Board Note:
Derived from 40 CFR 401.11(g)
(1986))
79.632

—9C—
“POTW” means “Publicly Owned Treatment Works,”
which is
defined below.
“POTW Treatment Plant” means that portion of the POTW
which is designed
to provide
treatment (including
recycling
and reclamation)
of municipal sewage and
industrial
wastewater.
(Board Note:
Derived
from 40 CFR 403.3(p)
(1986))
“Pretreatment” means the reduction of the amount of
pollutants,
the elimination of pollutants or
the
alteration of the nature of pollutant properties
in
wastewater
prior
to or
in
lieu of discharging or
otherwise introducing such pollutants into
a
POTW.
The
reduction or alteration may be obtained by physical,
chemical
or biological
processes, process changes or
by
other
means,
except
as prohibited
by Section 310.232.
Appropriate
pretreatment technology includes control
equipment,
such as equalization tanks
or
facilities, for
protection against surges or
slug loadings which might
interfere with or otherwise be imcompatible with the
POTW.
However, where wastewater
from a
regulated
process is mixed
in
an equalization facility with
unregulated wastewater
or with wastewater
from another
regulated process, the effluent
from the equalization
facility must meet an
adjusted pretreatment limit
calculated
in
accordance with Section 310. 233.
(Board
Note:
Derived
from 40 CFR 403.3(q)
(1986))
“Pretreatment permit” means an authorization to
discharge
to
a sewer which
is issued by the Agency as
the control authority.
“Pretreatment requirements” means any substantive or
procedural requirement related
to pretreatment, other
than
a pretreatment standard, imposed on
an industrial
user.
(Board Note:
Derived from 40 CFR 403.3(r)
(1986))
“Pretreatment standard,”
or
“standard” means any
regulation containing
pollutant discharge limits
promulgated by USEPA,
and incorporated by reference
in
35 Ill.
Adm.
Code 307.
This term includes prohibitive
discharge limits established pursuant
to Section 310.201
through
310.213
or
35 Ill.
Adiri. Code 307.1101.
This
term also includes more stringent prohibitions and
standards adopted by the Board
in this Part or 35
Ill.
Adni.
Code 307,
including 35 111.
Adin.
Code 307.1101,
307.1102 and
307.1103.
The term also includes local
limits pursuant
to Section
310.211 which
are
a part of
an approved pretreatment program.
79-633

—lOC—
(Board
Note:
Derived from 40 CFR 403.3(j)
(1986))
“Process wastewater”
means any water which, during
manufacturing
or processing, comes
into direct contact
with or results from the production or
use of any raw
material, intermediate product, finished product, by-
product or waste product.
(Board Note:
Derived
from 40 CFR 401.11(q)
(1986))
“Process wastewater
pollutants” means pollutants present
in process wastewater.
(Board Note:
Derived from 40 CFR 401.11(r)
(1986))
“Publicly owned treatment works”
or
“POTW” means
a
“treatment works” which is owned
by a “unit of local
government.”
This definition
includes any devices and
systems used
in the storage, treatment, recycling
and.
reclamation of municipal sewage or
industrial
wastewater.
It also includes sewers, pipes and other
conveyances only if they convey wastewater
to
a
POTW
treatment plant.
The
term also means the
“unit of local
government”
which has jurisdiction over the indirect
discharges to and
the discharges from such
a treatment
works.
(Board
Note:
Derived
from 40 CFR 403.3(o)
(1986))
“Schedule
of
compliance”
means
a
schedule
of
remedial
measures included
in
an authorization
to discharge or
a
pretreatment permit,
or
an
NPDES
permit,
including
an
enforceable sequence of interim requirements
(for
example, actions, operations or milestone events)
leading
to compliance with this Part and 35 Ill.
Adni.
Code
307.
Schedules of compliance may be established
pursuant
to an approved pretreatment program or these
rules,
or pursuant
to
a Board
Order
in a variance or
enforcement
action.
(Board Note:
Derived from
40 CFR 401.11(m)
(1986) and
33 USC 1362(17))
“Submission” means
a request
to
the Agency by a POTW for
approval of a pretreatment program.
(Board Note:
Derived
from 40 CFR 403.3(t)
(1986))
“Treatment works”
is as defined
in
33 USC 1292(2)
(1986).
It includes any devices and systems used
in
the
storage, treatment,
recycling and reclamation of
municipal
or
industrial wastewater
to implement
33 USC
1281,
or
necessary
to
recycle
or
reuse
water
at the most
79-634

—llC—
economical cost over
the estimated life of the works,
including intercepting
sewers, outfall
sewers, sewage
collection systems, pumping, power
and other equipment.
(Board Note:
Derived from 40 CFR 403.3(o)
(1986) and
33
USC 1292(2))
“Unit of local government” means
a unit of local
government,
as defined by Art.
7,
Sec.
1 of the Illinois
Constitution, having jurisdiction over disposal
of
sewage.
“Unit
of
local
government”
includes,
but
is
not
limited
to, municipalities and sanitary districts.
(Board Note:
Derived from 40 CFR 401.11(w)
(1986)
and
33 USC 1362(4))
“USEPA” means the United States Environmental Protection
Agency.
SUBPART B:
PRETREATMENT STANDARDS
Section 310.201
General
Prohibitions
a)
No user
shall
introduce
into
a
POTW any pollutant which
causes pass through or
interference.
b)
Affirmative defenses.
A user has an affirmative defense
in any action brought against
it alleging
a violation of
subsection
(a)
or
35 Ill.
Adxn.
Code 307,
Subpart B if
the user demonstrates:
1)
The user did not know or have reason
to know that
its discharge,
alone or
in conjunction •with
a
discharge or discharges from other
sources, would
cause pass through or
interference;
and
2)
Either:
A)
The POTW developed
in accordance with Section
310. 210
a local limit which was designed
to
prevent
pass through or interference for each
pollutant
in
the
user’s
discharge
which
caused
pass through or interference, and the user was
in compliance with each such local
limit
immediately prior
to and during
the pass
through
or
interference;
or
B)
If the POTW has not developed in accordance
with Section 310.210 local limits which are
designed
to
prevent
pass
through
or
interference for the pollutants which caused
the pass through or interference, the user’s
discharge
immediately
prior
and during
the
pass through or interference did not change
79-635

—l2C—
substantially
in nature or consitutents from
the user’s prior discharge activity during
which
the
POTW was regularly in compliance
with the POTW’s NPDES permit requirements and,
in
the
case
of
interference,
applicable
requirements
for
sewage sludge
use or
disposal.
C)
These
general
prohibitions
and
the
specific
prohibitions
in Section 310.202 apply
to each user introducing
pollutants into
a POTW whether
or not the user
is
subject to other pretreatment standards or
any national,
state or local pretreatment requirements.
(Board Note:
Derived
from 40 CFR 403.5(a)
(1986), as
amended at
52 Fed.
Peg.
1600, January 14,
1987)
Section
310.202
Specific Prohibitions
No person shall cause or allow the introduction
into
a POTW of
the pollutants specified
in 35
111.
Adm.
Code
307,
Subpart
B.
(Board Note:
Derived
from 40 CFR 403.5(b)
(1986))
Section
310.210
Specific Limits Developed by POTW
a)
Each POTW which
is required
to develop
a pretreatment
program shall,
as part of the program, develop and
enforce specific limits
to
implement the prohibitions
listed
in Sections
310.201(a)
and 310.202.
b)
POTW’s which are not required
to develop a pretreatment
program shall,
in cases
where pollutants contributed by
one or more users result
in interference or pass
through,
and such violation is likely to recur,
develop
and enforce
specific discharge limits
for industrial
users,
and all other
users, as appropriate,
which,
together with appropriate changes
in
the POTW treatment
plant’s facilities
or operation,
are necessary
to ensure
renewed and continued compliance with the POTW’s NPDES
permit,
and
sludge
use
or
disposal
practices.
c)
Prior
to developing
specific discharge limits,
POTW’s
shall give,
to persons or groups which have requested
notice, individual
notice and
an
opportunity
to
respond.
d)
The PCTW shall base limitations developed pursuant
to
this Section on
the characteristics and treatability of
the wastewater by the PCTW,
effluent limitations which
the POTW must meet, sludge disposal practices, water
quality standards
in the receiving stream and the
pretreatment standards and requirements of this Part and
35
Ill. Adm. Code 307.
79-636

—l3C—
(Board
Note:
Derived from 40 CFR 403.5(c)
(1986),
as
amended
at
52 Fed. Reg.
1600,
January 14,
1987)
Section 310.211
Local
Limits
If
a POTW develops,
in accordance with Section 310.210,
specific
prohibitions or
limits on pollutants,
or
pollutant
parameters,
such limits
shall
be deemed
pretreatment standards
for the
purposes of this Part.
(Board
Note:
Derived
from 40 CFR 403.5(d)
(1986))
Section 310.220
Categorical Standards
Pretreatment standards specifying quantities or concentrations of
pollutants
or pollutant properties which may be discharged
to
a
POTW
by
existing
or
new
industrial
users
in specific
industrial
subcategories will be established
as separate regulations
under
35
Ill. Adm. Code 307.
These standards,
unless specifically
noted otherwise,
shall
be
in
addition
to the general prohibitions
established
in Sections 310.201 through 210.211.
(Board Note:
Derived
from 40 CFR 403.6
(1986))
Section 310.221
Category Determination Request
a)
Application deadline.
1)
The
industrial user or POTW may request that the
Agency provide written certification as
to whether
the industrial
user
falls within that particular
subcategory.
If an existing
industrial
user adds
or changes
a process or operation which may be
included
in
a subcategory,
the existing
industrial
user
shall
request this certification prior
to
commencing discharge
from the added or
changed
processes
or operation.
With respect
to new
standards:
A)
The POTW or user
shall direct to USEPA any
category
determination
requests
for
pretreatment standards adopted by USEPA prior
to authorization of the Illinois program.
B)
After
authorization of the Illinois program,
the
POTW or
user
shall direct
to the Agency
any category determination requests within 60
days after
the Board
adopts or incorporates by
reference
a pretreatment standard for
a
subcategory under which
an
industrial user may
be
included.
2)
A new source
shall
request this certification prior
to commencing discharge.
79-637

—l4C—
3)
If
a request for certification is submitted by
a
POTW,
the POTW shall
notify any affected
industrial
user of such applications.
The industrial
user may
provide written comments on the POTW submissions to
the Agency within 30 days of notification.
b)
Contents of application.
Each request shall contain
a
statement:
1)
Describing which subcategories might
be applicable;
and
2)
Citing evidence and reasons why a particular
subcategory
is
applicable
and
why
others
are
not
applicable.
Any person signing the application
statement submitted pursuant
to this Section shall
make
the following certification:
I have personally examined and
am
familiar
with the information submitted
in
the attached
document, and
I hereby certify under
penalty
of law that this information was obtained
in
accordance with the requirements of Section
310.221.
Moreover, based upon my inquiry of
those individuals
immediately responsible for
obtaining
the
information reported herein,
I
believe that the submitted information is
true, accurate and complete.
I am aware that
there
are significant penalties
for submitting
false information, including the possibility
of
fine and imprisonment.
c)
Deficient requests. The Agency shall act only on written
requests for determinations which contain all of the
information required.
The Agency shall notify persons
who have made incomplete submissions that
their requests
are deficient and that, unless the time period
is
extended, they have
30 days to correct the deficiency.
If the deficiency is not corrected within
30 days,
or
within an extended period
allowed by the Agency, the
Agency shall deny the request for
a determination.
d)
Final
determination.
1)
When
the Agency receives
a submission, the Agency
shall,
if
it determines that the submission
contains all
of the
information required by
subsection
(b), consider
the submission, any
additional evidence that may have been requested
and any other available information relevant
to the
request.
The Agency shall
then make
a written
determination of the applicable subcategory and
state
the reasons for the determination.
79.638

—15C—
2)
The
Agency
shall
forward
the
determination
described
in subsection
(d)(1)
to USEPA.
If USEPA
does not modify the Agency’s decision within
60
days after
its receipt, the Agency’s decision
is
final.
3)
If USEPA modifies the Agency’s decision, USEPA’s
decision
will
be
final.
4)
The Agency shall
send
a copy of the determination
to
the
affected
industrial
user
and
the
POTW.
If
the final
determination is made by USEPA,
the
Agency
shall
send
a
copy
of
the
determination
to
the user.
e)
Requests
for
hearing
and/or
legal
decision.
1)
Within
30 days following the date of receipt of
notice of the final determination
as provided
for
by subsection
(d)(4), the requester may submit
a
petition to reconsider
or contest the decision
to
USEPA, which
will act pursuant
to
40 CFR
403.6(a)
(5).
2)
Within
35 days following
the date of receipt of
notice of the final determination
as provided
for
by subsections (c),
(d)(2)
or
(d)(4),
the requester
may appeal
a
final decision made by the Agency
to
the Board.
(Board Note:
Derived from 40 CFR 403.6(a)
(1986))
Section 310.222
Deadline
for Compliance with Categorical
Standards
a)
If
a compliance date for
a categorical pretreatment
standard
is adopted or
incorporated by reference
in
35
Ill.
Adni. Code 307, then dischargers shall
comply with
the standard by the following times, whichever
is last:
1)
The date specified or
incorporated by reference;
or
2)
The date the Board adopts
or incorporates the
standard by reference; or
3)
The date USEPA approves the Illinois pretreatment
program.
b)
If no compliance date for
a categorical pretreatment
standard
is adopted or
incorporated by reference
in
35
Ill.
Adm. Code 307, then dischargers shall comply with
the standard by the following times, whichever
is last:
79.639

—l6C—
I)
The date the Board adopts
or incorporates the
standard by reference; or
2)
The date
USEPA
approves
the
Illinois
pretreatment
program.
c)
This Section
shall not be construed
as extending
compliance dates
for enforcement of categorical
pretreatment standards pursuant
to statutes and
regulations existing prior
to authorization of the
Illinois pretreatment program.
(Board
Note:
Derived from 40 CFR 403.6(b)
(1986))
Section 310.230
Concentration and Mass Limits
Pollutant discharge limits
in categorical pretreatment standards
will
be expressed either
as concentration or mass limits.
Limits
in categorical
pretreatment standards shall apply to the
discharge from the process regulated by the standard,
or
as
otherwise specified by the standard.
(Board Note:
Derived from 40 CFR 403.6(c)
(1986))
Section 310.232
Dilution
Except where expressly authorized
to do
so by an applicable
categorical
pretreatment standard, no industrial
user shall
increase the
use of process water or,
in any other
way, attempt
to dilute
a discharge as
a partial
or complete substitute
for
adequate treatment
to achieve compliance with
a pretreatment
standard.
The control authority may impose mass limitations
on
industrial
users which are using dilution to meet applicable
pretreatment standards,
or
in other cases where
the imposition of
mass limitations is appropriate.
POTW’s may allow dilution
to
meet
local
limits
developed
under
Section
310.210.
(Board Note:
Derived from 40 CFR 403.6(d)
(1986))
Section 310.233
Combined Wastestream Formula
Where process wastewater
is mixed prior
to treatment with
wastewaters other than those generated by the regulated process,
the control authority shall derive
fixed alternative discharge
limits, which the control authority shall apply to the mixed
discharge.
When
it is deriving alternative categorical limits,
the control authority shall calculate both an alternative daily
maximum value
using
the daily maximum value(s)
specified
in the
appropriate
categorical
pretreatment
standard(s)
and
an
alternative
consecutive
sampling
day
average
value
using
the
average monthly value(s)
specified
in
the appropriate categorical
pretreatment standard(s).
The
industrial
user
shall
comply with
the alternative daily maximum
and
average
monthly
limits
fixed
by
the control authority until
the control authority modifies the
79-640

—l7C—
limits
or approves an industrial user modification request.
Modification
is authorized whenever
there
is
a material
or
significant change
in
the values used
in the calculation
to fix
alternative limits
for
the regulated pollutant.
An
industrial
user
shall
immediately
report
any
such
material
or
significant
change
to the control
authority.
Where appropriate, the control
authority shall calculate new alternative categorical limits
within
30 days.
a)
Alternative limit calculation.
For purposes of these
formulas, the “average daily flow” means
a reasonable
measure of the average daily flow for
a 30—day period.
For new sources,
flows shall
be estimated
using
projected
values.
The
control
authority
shall
derive
the alternative limit
for
a specified pollutant by the
use of either
of the following formulas:
1)
Alternative concentration limit.
C
=
(T—D)SUM(CiFi)
/
(T)SUM(Fi)
where
C
=
The alternative concentration limit for the
combined wastestrearn.
Ci
=
The categorical
pretreatment standard
concentration limit
for
a pollutant
in the
regulated stream
i.
Fi
=
The average daily flow (at least
a
30—day
average)
of stream
i
to
the extent that
it
is
regulated for such pollutant.
“SUM(Gi)” means the sum of the results of
calculation
G for
streams
i
=
1
to
i
=
N.
N
=
The
total
number
of regulated streams.
T
=
The
average
daily
flow
(at
least
a
30—day
average)
through
the
combined
pretreatment
facility
(includes
Fi,
D
and
unregulated
streams.
D
=
The
average
daily
flow
(at
least
a
30—day
average)
from:
A)
Boiler blowdown streams and non—contact
cooling streams,
subject
to the proviso of
subsection
(d); and
B)
Sanitary wastestreams where such wastestreams
are not regulated by
a categorical
pretreatment standard;
and,
79-641

—18C-
C)
From any process wastestreams which were or
could have been entirely exempted
from
categorical pretreatment standards as
specified
in subsection
(e).
2)
Alternative mass limit.
M
=
(T-D)SUM(Mi)
/
SUM(Fi)
where
M
=
The alternative mass limit
for
a pollutant in
the combined wastestream.
Mi
=
The categorical pretreatment standard mass
limit for
a pollutant
in the regulated stream
i
(the categorical pretreatment mass limit multiplied
by the appropriate measure of production)
Fi
=
The average daily flow (at least
a
30—day
average)
of stream
i
to the extent that
it is
regulated
for
such pollutant.
“SUM(Gi)” means the sum of the results of
calculation G for streams
i
=
1 to
i
=
N.
N
=
The
total
number
of
regulated
streams.
T
=
The average daily flow (at least
a
30—day
average) through the combined pretreatment facility
(includes Fi,
D and unregulated streams.
D
=
The average daily flow (at
least
a
30—day
average)
from:
A)
Boiler
blowdown
streams
and
non—contact
cooling
streams, subject
to the proviso of
subsection
(d); and
B)
Sanitary wastestreams where such wastestreams
are not regulated by a categorical
pretreatment
standard;
and,
C)
From any process wastestreams which were or
could have been entirely exempted
from
categorical
pretreatment
standards
as
specified
in
subsection
(e).
b)
Alternative
limits
below
detection.
An
alternative
pretreatment limit
shall not be used
if the alternative
limit
is
below
the analytical detection limit
for any of
the regulated pollutants.
C)
Self—monitoring.
Self—monitoring
required
to insure
79-642

—l9C—
compliance with
the
alternative
categorical
limit
shall
be
as follows:
1)
The
type
and frequency of
sampling,
analysis
and
flow measurement
shall be determined by reference
to
the self—monitoring
requirements of the
appropriate categorical pretreatment standard(s).
2)
Where
the self—monitoring
schedules for the
appropriate
standards differ, monitoring
shall be
done according
to
the most frequent schedule..
3)
Where flow determines the frequency of self—
monitoring
in
a categorical pretreatment standard,
the sum of all
regulated flows
(Fi)
is the flow
which
shall
be
used
to determine self—monitoring
frequency.
d)
Proviso
to subsections
(a)(l) and
(a)(2).
Where boiler
blowdown and non—contact cooling streams contain
a
significant amount of
a pollutant, and the combination
of such streams,
prior
to pretreatment, with the
industrial
user’s regulated process wastestream(s) will
result
in
a substantial reduction of that pollutant,
the
control authority,
upon application of the industrial
user,
shall determine whether such wastestreams
should
be classified
as diluted
or unregulated.
In
its
application
to the control authority,
the industrial
user shall provide engineering, production,
sampling and
analysis and such other
information
so the control
authority can make
its determination.
e)
Exemptions from categorical pretreatment standards.
Process wastestreams were or could have been entirely
exempted
from categorical pretreatment standards
pursuant
to paragraph
8 of the NRDC v.
Costle consent
decree
(12 ERC 1833)
for one or more of the following
reasons (see 40 CFF
403, Appendix
D (1986)):
1)
The pollutants of concern are not detectable
in the
discharge from the industrial
user;
2)
The pollutants of concern are present only in trace
amounts and are neither causing nor are likely to
cause
toxic effects;
3)
The pollutants of concern are present
in amounts
too small
to be effectively reduced by technologies
known
to
USEPA;
4)
The wastestream contains only pollutants which are
compatible
with
the
POTW.
(Board Note:
Derived
from 40 CFR 403.6(e)
(1986))
79.643

—20C—
SUBPART
D:
PRETREATMENT PERMITS
Section 310.400
Preamble
a)
This Subpart contains rules
for the issuance of
pretreatment permits by the Agency when the Agency
is
acting
as the control
authority.
This Subpart does not
apply
if
the
POTW
is
the
control
authority.
b)
Users with pretreatment permits are not required
to have
operating permits pursuant
to 35
Ill.
Adm. Code 309,
Subpart
B.
However, sources may be required
to have
construction permits pursuant
to that Subpart.
Section
310.
401
Pretreatment
Permits
a)
No user who meets any of the
following criteria
shall,
without
a pretreatment permit, discharge to
a POTW,
unless
the
discharge
is
to
a
POTW
with
a
pretreatment
program approved pursuant
to Subpart
E:
1)
The
user
discharges
toxic
pollutants
as defined by
35
Ill.
Adm.
Code
307.1005.
2)
The user is subject
to
a categorical
standard
adopted
or
incorporated by reference
in
35 Ill.
Adm.
Code 307.
3)
The user discharges more
than 15
of the total
hydraulic flow received by the POTW treatment
plant.
4)
The user discharges more than
15
of the total
biological
loading of the POTW treatment plant as
measured by the 5—day biochemical oxygen demand.
5)
The user has been notified pursuant
to subsection
(b)
that
it must apply for
a pretreatment permit.
b)
A user which does not have
a pretreatment permit shall
apply for
a pretreatment permit within 30 days after
the
Agency notifies the user that the
user meets any of the
following criteria:
1)
The user
has caused pass through or
interference.
2)
The
user’s
discharge
presents
an
imminent
endangerment
to
the
health
or
welfare
of
persons.
c)
No person
shall
cause
or
allow
any discharge for whIch a
pretreatment permit has been
issued unless the discharge
is
in compliance with the conditions of the pretreatment
permit.
79.644

—2IC—
Section
310.402
Time to Apply
a)
Any person required
to have
a pretreatment permit shall
file an application with the Agency at least
90 days
before
the date
on which
the permit
is required.
b)
Any permittee who wishes to continue
to discharge after
the expiration date of
a pretreatment permit shall
apply
for reissuance of the permit at least
90 days prior
to
the
expiration
date
of
the
permit.
Section
310.403
Imminent Endangerment
Pursuant to Section
34
of the Act the Agency shall declare an
emergency and seal
any wastewater source
or discharge if
it
determines that the discharge presents an
imminent endangerment
to the health or welfare of
persons.
Section
310.410
Application
a)
Applications for pretreatment permits
shall
include the
following information:
1)
The location of the wastewater
source and
discharge;
2)
The location of the
sewer
to which
the user will
discharge;
3)
The POTW and treatment works which
will receive
the
discharge;
4)
The volume discharged;
5)
A description of the wastewater prior
to any
pretreatment and prior
to discharge,
including
a
statement as
to the presence or absence of all
contaminants
for which pretreatment recuirements
have been established
in 35
Ill. Adm.
Code
307;
6)
Any projected changes
in the volume or description
of the wastewater
which the user desires
to have
included
in the terms of the permit;
7)
A certification of capacity
to transport and treat
the wastewater as specified
in Section
310.411;
8)
Such additional
information as the Agency
determines
is necessary to determine whether
the
user will meet the requirements of this Part and 35
Ill. Adm. Code 307.
b)
The Agency
shall promulgate application forms
for
79.645

—22C—
pretreatment permits.
Section 310.411
Certification of Capacity
The user
shall obtain from the POTW and from the owners of any
intermediate sewers which will receive the wastewater
a signed
statement
certifying
that
they
have
adequate
capacity
to
treat
and transport the wastewater without violating any provisions of
any NPDES permit,
this Part, or
35
Ill.
Adm.
Code 302,
304, 307
or
309.
Section 310.412
Signatures
a)
If
a corporation submits an application, one of the
following persons shall
sign the application:
1)
A principal executive officer of at least
the level
of vice president;
or
2)
An authorized
agent of the corporation,
if the
agent
is responsible
for the overall operation of
the wastewater
source.
b)
If a partnership or
sole proprietorship submits an
application,
a general
partner
or
the proprietor shall
sign the application.
c)
If
a publicly owned
user submits an
application, one of
the following persons shall sign the application:
1)
The principal executive officer;
2)
The ranking
elected official;
or
3)
An authorized
employee.
Section
310.413
Site Visit
If the Agency determines that
a site visit
is necessary for
the
Agency
to evaluate the application,
it
shall
notify the applicant
within
30 days after receipt of the application and make
arrangements
to visit
the site.
Failure
to allow
a
site visit
renders the application incomplete.
Section
310.414
Completeness
a)
An application shall
be deemed filed when the Agency
receives all
information, documents and authorizations
in
the
form specified
in this Part.
b)
The Agency shall
notify applicants of incomplete
applications within 30 days after
the Agency receives
the application.
79-646

—230—
Section
310.415
Time
Limits
a)
If
a permittee files
a
timely application for renewal of
an existing pretreatment permit,
the existing permit
shall
continue until
the Agency takes
final
action on
the new application.
b)
If the Agency fails to take action on
an application for
a new permit within
90 days after
the application has
been received, the applicant may deem the permit issued
for
a period of one year
from the end of the
90 day
period.
This excuses the applicant from the requirement
to obtain a permit
only.
Section
310. 420
Standard
for Issuance
The Agency shall
issue
a pretreatment permit
to the discharger:
a)
If the discharger demonstrates that the discharge will
meet the requirements and standards of this Part and 35
Ill. Adm. Code 307;
or,
b)
If the Agency imposes
in the pretreatment permit
conditions sufficient
to assure future compliance with
the requirements and standards of this Part and 35
Ill.
Adrn. Code 307, including
a schedule of compliance
pursuant
to Section 310.432.
Section 310.421
Final Action
a)
If the Agency denies
a pretreatment permit,
it
shall
send the applicant
a written statement of the reasons
for denial
as provided by Section 39(a)
of the Act.
b)
The date of the Agency’s
final action
shall
be
the date
the pretreatment permit or
statement of reasons
for
denial
is mailed
to the applicant.
Section 310.430
Conditions
The Agency shall
impose
the following conditions
in each permit:
a)
Discharge limitations based on 35
Ill.
Adm. Code 307.
b)
More stringent discharge limitations based
the ability
of the POTW to treat the discharge without interference
or
pass through.
c)
Requirements that the discharger collect and analyze
samples of the discharge.
d)
Requirements that the discharger report the results of
sample analysis
to the Agency.
79.647

—240—
e)
Requirements that the discharger allow authorized
representatives of the Agency, at reasonable times, upon
presentation of credentials,
to
inspect its premises
and
collect samples
of the discharge.
f)
An expiration date,
as specified
in Section
310.431.
g)
If the applicant does not demonstrate compliance with
this Part and
35
Ill. Adm.
Code 307,
a schedule of
compliance
as specified
in
Section 310.432.
h)
A requirement that the applicant
file an application
to
modify the permit when notified pursuant
to Section
310. 442.
i)
Such additional conditions as the Agency determines are
necessary to assure that the discharge complies with the
requirements of this Part and
35
Ill.
Adm. Code 307.
Section
310.431
Duration of Permits
No pretreatment permit shall have
a duration in excess of five
years.
In
establishing
earlier
expiration
dates,
the
Agency
shall
consider the following:
a)
Coordination with
future compliance deadlines;
b)
Maintenance of intensive control over new or
experimental processes;
and
c)
Whether
the permit addresses an emergency situation.
Section 310.432
Schedules of Compliance
a)
The Agency shall establish
a
schedule of compliance
in
any pretreatment permit unless the discharger
demonstrates compliance with this Part and 35 Ill. Adm.
Code 307,
if the discharger has received
a variance
pursuant
to
35
Ill.
Adm. Code 104
or
if the discharger
has been ordered
to come into compliance with this Part
pursuant
to
35
Ill.
Adm. Code 103.
b)
Schedules of compliance,
including those established by
variance or Board order, shall
require the permittee
to
take specific
steps
to achieve compliance within the
shortest practicable period
of time, and shall
be
consistent with requirements
in the Clean Water Act and
40 CFR
403
(1986).
c)
The schedule of compliance
shall contain
the following:
1)
Increments of progress
in the
form of dates
for
the
commencement
and
completion
of
major
events
leading
to the construction and operation of additional
79-648

—25C—
pretreatment required
to meet the standards of
35
Ill. Adm. Code 307.
No increment of progress
shall
exceed nine months.
2)
A requirement that the user submit progress reports
no later than fourteen days following each date in
the schedule, including
the final date
for
compliance.
The progress report
shall
include, at
a minimum, the following:
A)
Whether or not the user met the date specified
in
the schedule of compliance.
B)
If the user did not meet the dates,
the date
on which the user expects to accomplish this
increment of progress, the reason
for
the
delay and
steps being
taken
to
return
construction
to the schedule of compliance.
3)
A requirement that in
no event more than nine
months elapse between progress reports.
d)
It
is not necessary to show
a violation of a
pretreatment standard or requirement
to enforce interim
and
final compliance dates.
Section 310.441
Effect of a Permit
Existence of
a pretreatment permit
is
a defense only to
a charge
of operation without
a permit.
Section 310.442
Modification
a)
The permittee may request modification of the permit at
any time by filing an application.
b)
If the Agency finds new information or
if the Board
adopts new regulations relevant
to the permit, the
Agency shall notify the permittee that
it intends to
modify
the
permit.
The
Agency
shall
give
the
permittee
the opportunity to
file
a new application before
it
modifies
the
permit.
Section
310.
443
Revocation
The
Board
may
revoke
a
pretreatment
permit
pursuant
to
Section
33
of
the
Act
and
35
Ill.
Adm.
Code
103.
Causes
for
revocation
of
a
permit include, but are not limited to, the following:
a)
Violation of permit conditions,
including, but not
limited
to, schedules of compliance, monitoring
and
inspection;
b)
Obtaining
a permit by misrepresentation or failure
to
79.649

—260-
disclose
fully
all
relevant
facts;
or
c)
A
change
in
circumstance
which
mandates
either
a
temporary
or
permanent
reduction
or
elimination
of
the
discharge.
Section
310.444
Appeal
Within 35 days after
final Agency action, the applicant may
appeal
the denial of a pretreatment permit,
or
the issuance of a
pretreatment permit with conditions,
to the Board pursuant
to
Section
40 of the Act and
35
Ill.
Adin.
Code 105.
SUBPART
D:
POTW
PRETREATMENT PROGRAMS
Section
310.501
Pretreatment
Programs
Required
a)
The Agency shall
require
to establish
a pretreatment
program any POTW
(or combination of POTWs operated by
the
same
authority)
with
a
total
design
flow
greater
than
5 million gallons per day
(mgd)
which:
1)
Receives from industrial users pollutants which
pass through or
interfere with the operation of the
POTW; or
2)
Receives from industrial users discharges which are
otherwise subject
to categorical standards
in 35
Ill. Adm. Code 307
b)
The Agency shall
require that
a POTW with
a design flow
of
5 mgd or less develop a
PCTW pretreatment program if
the Agency finds that.the nature or volume of the
industrial
influent, treatment process
upsets,
violations of POTW effluent limitations, contamination
of municipal sludge or other circumstances require
a
pretreatment program
in order
to prevent interference or
pass—through.
c)
Subsections
(a)
and
(b) notwithstanding,
the Agency may,
in its discretion,
waive the requirement that any POTW
develop
a pretreatment program.
1)
Waivers
shall
be
in writing.
2)
The Agency may,
in its discretion, rescind
any
waiver by giving written notice
to the
POTW, giving
sufficient time for the POTW to develop the
program.
(Board
Note:
Derived
from
40 CFP
403.8(a)
(1986))
Section
310. 502
Deadline
for Program Approval
79-650

—27C—
A
POTW
which
meets
the
criteria
of
Section
310.
501
must
receive
approval of
a POTW pretreatment program
no later
t.han one year
after
the
issuance,
reissuance
or
renewal
of
the
POTW’s
NPDES
permit
to
require
development
of
a
pretreatment
program.
The
PCTW
pretreatment
program
shall
meet
the
criteria
set
forth
in
Section 310.510 and
shall
be administered
by the POTW to ensure
compliance by industrial
users with applicable pretreatment
standards and
requirements.
(Board
Note:
Derived from 40 CFR 403.8(b)
(1986))
Section 310.503
Incorporation of Approved Programs
in Permits
A POTW may develop an appropriate POTW pretreatment program any
time
before
the
time
limit
set
forth
in
Section
310.502.
the
approved
POTW
pretreatment
program
shall
be
incorporated
into
the
POTW’s
NPDES permit.
(Board
Note:
Derived
from
40
CFR
403.8(c)
(1986))
Section 310.504
Incorporation of Compliance Schedules
in
Permit
S
If the POTW does not have
an approved pretreatment program at
the
time the
POTW’s existing NPDES permit is reissued or modified,
the reissued
or modified permit
shall
contain the shortest
reasonable compliance schedule,
not
to exceed one year,
for
the
approval of the legal authority, procedures and funding required
by Section
310.510.
(Board Note:
Derived from 40 CFR 403.8(d)
(1986))
Section 310. 505
Reissuance or Modification of Permits
The Agency shall modify or, alternatively, reissue
a POTW’s NPDES
permit
in order
to:
a)
Put the POTW on
a compliance schedule for the
development of
a
POTW
pretreatment program where the
addition of pollutants into
a
POTW by an
industrial user
or
combination
of
industrial
users
presents
a
substantial
hazard
to the functioning
of the treatment
works,
quality of the receiving waters, human health or
the environment;
b)
Incorporate
an approved
POTW pretreatment program
in the
POTW permit;
or
c)
Incorporate
a compliance schedule for the development of
a
POTW pretreatment program
in the
POTW
permit.
(Board
Note:
Derived
from
40
CFR
403.8(e)
(1986))
Section
310.510
Pretreatment
Program
Requirements
79-651

A POTW pretreatment program shall meet the following
requirements:
a)
Legal
authority.
The
POTW
shall
operate
pursuant
to
legal
authority
enforceable
in
federal,
state
or
local
courts, which authorizes or enables the
POTW
to apply
and
to enforce the requirements of this Part and 35 Ill.
Adm. Code 307.
Such authority may be contained
in
a
statute, ordinance or series of joint powers agreements
which
the POTW is authorized
to enact, enter
into or
implement,
and which are authorized by State
law.-
At
a
minimum, this legal authority shall enable the
POTW
to:
1)
Deny or condition new or
increased contributions of
pollutants, or changes
in the nature of pollutants,
to the
ROTh
by industrial
users where such
contributions
do
not
meet
applicable
pretreatment
standards
and
requirements
or
where
such
contributions would
cause
the POTW to violate its
NPDES permit;
2)
Require compliance with applicable pretreatment
standards
and
requirements
by
industrial
users;
3)
Control, through ordinance, permit, order
or
similar means,
the contribution
to the P0Th by each
industrial user
to ensure compliance with
applicable pretreatment standards and requirements;
4)
Require:
A)
The development of a compliance schedule by
each industrial
user for
the installation of
technology required
to meet applicable
pretreatment standards and requirements; and
B)
The submission of all notices and self—
monitoring
reports from industrial users as
are necessary to assess and assure compliance
by industrial
users with pretreatment
standards and requirements, including, but not
limited,
to the reports required
in Subpart D;
5)
Carry out all inspection, surveillance and
monitoring procedures necessary to determine,
independent of information supplied by industrial
users,
compliance
or
noncompliance
with
applicable
pretreatment standards and requirements by
industrial
users.
Representatives of the POTW
shall
be
authorized
to
enter
any
premises of any
industrial
user
in
which
a
discharge
source
or
treatment
system
is
located
or
in
which
records
are
required
to
be
kept
under
Section
310.634
to
assure
79-652

—29C—
compliance with pretreatment standards.
Such
authority shall
be
at least as extensive as the
authority provided under
Section 308 of the
CWA;
6)
Obtain
remedies
for
noncompliance
by
any
industrial
user
with any pretreatment standard or requirement.
A)
All
POTW’s
shall be able
to
seek
injunctive
relief
for
noncompliance
by
industrial
users
with pretreatment standards or requirements.
The ROTh shall pass legislation
to seek
arid
assess
civil
or
criminal
penalties
for
noncompliance
by
industrial
users
with
pretreatment standards and requirements.
B)
Pretreatment
requirements
which
will
be
enforced
through
the
remedies
set
forth
in
subsection
(a)(6)(A)
will
include
but
not
be
limited
to:
the duty to allow or carry out
inspections, entry or monitoring activities;
any
rules,
regulations
or
orders
issued
by the
POTW;
or
any reporting requirements imposed by
the POTW,
this Part or
35 Ill. Adm. Code
307.
The POTW shall
have authority and
procedures (after
notice
to the
discharger)
immediately and effectively
to halt or
prevent
any discharge of
pollutants
to
the
POTW
which
reasonably
appears
to
present
an
imminent
endangerment
to the health
or welfare of
persons.
The
POTW shall also have authority
and procedures (which shall
include notice
to
the
affected
industrial
users
and
an
opportunity to
respond)
to halt or prevent any
discharge
to
the
POTW
which
reasonably
appears
to present
an endangerment
to the environment
or which threatens
to interfere with the
operation of the POTW.
The Agency shall have
authority to seek judicial relief
for
noncompliance
by
industrial
users
when
the
POTW has acted
to seek such relief but has
sought
a
penalty
which
the
Agency
finds
to
be
insufficient.
The procedures
for
notice
to
dischargers where
the POTW is seeking
ex parte
temporary judicial injunctive relief will be
governed
by
applicable
state
or
federal
law
and not by this provision; and
7)
Comply with the confidentiality requirements set
forth
in
Section
310.105
b)
Procedures.
The POTW shall develop and
implement
procedures
to ensure compliance with the requirements of
a pretreatment program.
At
a minimum, these procedures
shall
enable
the
ROTh
to:
79-653

—30C—
1)
Identify and locate
all possible
industrial users
which
might
be subject
to the POTW pretreatment
program.
Any compilation,
index
or inventory of
industrial users made under
this subsection shall
be made available
to the Agency upon request.
2)
Identify the character and volume of pollutants
contributed
to
the
POTW
by
the
industrial
users
identified
under subsection
(b)(l).
This
information
shall be made available
to the Agency
upon request.
3)
Notify industrial
users identified
under subsection
(b)(l)
of
applicable
pretreatment
standards
and
any
applicable requirements under Section 204(b)
and
405 of the
CWA
and Subtitles
C
and
D of the
Resource Conservation and Recovery Act.
4)
Receive and analyze self—monitoring reports and
other
notices
submitted
by
industrial
users
in
accordance with the self—monitoring requirements
in
Subpart D;
5)
Randomly
sample
and
analyze
the
effluent
from
industrial
users
and
conduct
surveillance
and
inspection activities in order
to
identify,
independent of
information supplied by industrial
users,
occasional
and
continuing
noncompliance
with
pretreatment standards.
The
results
of
these
activities shall
be made available
to the Agency
upon request;
6)
Investigate
instances of noncompliance with
pretreatment standards and requirements, as
indicated
in the reports and notices required under
Subpart D,
or as indicated by analysis,
inspection
and surveillance activities described
in subsection
(b)(5).
Sample taking
and analysis, and the
collection of other
information, shall
be performed
with sufficient care
to produce evidence admissible
in enforcement proceedings or
in judicial actions;
and
7)
Comply with the public participation requirements
of
40 CFR 25
(1986)
in the enforcement of
pretreatment standards.
These procedures shall
include provision
for providing,
at least annually,
public notification,
in
a daily newspaper of
general circulation
in the
unit of local government
in
which
the
POTW
is
located,
of
industrial
users
which, during the previous
12 months, were
significantly violating applicable pretreatment
standards or other pretreatment requirements.
For
79-654

—3lC—
the purposes of this provision,
a significant
violation
is
a violation which remains uncorrected
45 days after notification of noncompliance; which
is part of
a pattern of noncompliance over
a twelve
month
period;
which
involves
a
failure
to
accurately report noncompliance; or which resulted
in the P0Th exercising its emergency authority
under subsection
(a)(6)(B).
c)
The P0Th shall have sufficient resources and qualified
personnel
to carry the authorities and procedures.
described
in subsections
(a)
and (b).
(Board Note:
Derived from 40 CFR 403.8(f)
(1986))
Section 310.521
Program Approval
A
POTW
requesting approval of a POTW pretreatment program shall
develop a program description which
includes the
information set
forth
in Sections 310.522(a)
through
(d).
This description shall
be submitted to the Agency which will make
a determination on the
request for program approval
in accordance with the procedures
described
in Sections 310.540 through 310.546.
(Board Note:
Derived from 40 CFR 403.9(a)
(1986))
Section 310.522
Contents of Program Submission
The program description must contain the following information:
a)
A statement from the attorney or other official acting
in
a
comparable
capacity
for
the
unit
of
local
government that the POTW has authority adequate
to carry
out the programs described
in Section 310. 501 through
310.510.
This statement shall:
1)
Identify the provision of the legal
authority under
Section 310.510(a)
which provides the basis
for
each procedure under Section 310.510(b);
2)
Identify the manner
in which the POTW will
implement
the
program
requirements
set
forth
in
Sections 310.501 through 310.510, including the
means by which pretreatment standards will be
applied
to individual
industrial
users
(e.g., by
order, permit, ordinance, contract, etc.); and,
3)
Identify how the POTW intends
to ensure compliance
with pretreatment standards and requirements, and
to enforce them
in the event of noncompliance by
industrial
users;
b)
A copy of any statutes, ordinances,
regulations,
contracts, agreements or other
authorities relied upon
79-655

—32C
by the P0Th for
its administration of the program.
This
submission shall
include
a statement reflecting
the
endorsement
or
approval
of
the
local
boards
or
bodies
responsible for supervising
and/or funding the POTW
pretreatment program if approved;
c)
A brief description
(including organization charts)
of
the POTW organization which will administer the
pretreatment program.
If more than one agency
is
responsible
for administration of the program the
responsible agencies should
be
identified, their
respective responsibilities delineated
and their
procedures for coordination set forth; and
d)
A description of the funding levels and full— and part—
time manpower available
to implement the program;
(Board Note:
Derived
from 40 CFP 403.9(b)
(1986))
Section 310.531
Agency Action
Any P0Th requesting POTW pretreatment program approval shall
submit
to
the Agency three copies of the submission described
in
Section 310.522.
Upon a preliminary determination that the
submission meets the requirements of Section
310. 522 the Agency
shall:
a)
Notify the POTW that the submission has been received
and
is under
review; and
b)
Commence
the public notice
and evaluation activities set
forth
in Section 310.540 through
310.546.
(Board Note:
Derived from 40 CFR 403.9(e)
(1986))
Section 310.532
Defective Submission
If, after review of the submission
as provided for
in Section
310.531, the Agency determines that the submission does not
comply with the requirements of Section 310.522, the Agency shall
provide notice
in
writing
to the applying P0Th and each person
who has requested
individual notice.
This notification shall
identify
any
defects
in the submission and advise
the
POTW and
each person who has requested
individual notice of the means by
which
the
P0Th
can
comply with the applicable requirements of
Section 310. 522.
(Board Note:
Derived from 40 CFR
403.9(f)
(1986))
Section
310.533
Water Ouality Management
The Agency shall
review POTW pretreatment programs to assure
consistency
with
water
quality
management
plans.
79.656

—33C—
(Board Note:
Derived from 40 CFR 403.9(g)
(1986))
Section 310. 541
Deadline for Review
The
Agency
shall
have
90
days
from the date of public notice of
any submission complying with the requirements of Section 310.522
to review the submission.
The Agency shall review the submission
to determine compliance with the requirements of Section 310. 502
and
310.510.
The
Agency
may
have
up
to
an
additional
90
days
to
complete the evaluation of the submission
if the public comment
period provided
for
in Section 3l0.542(a)(2)
is
extended beyond
30 days or
if
a public hearing
is held
as provided for
in Section
310.542(b).
In
no event, however,
shall
the
time for evaluation
of the submission exceed
a total
of 180 days from the date of
public notice of
a submission meeting the requirements of Secton
310. 522.
(Board Note:
Derived
from 40 CFP 403.11(a)
(1986))
Section 310.542
Public Notice and Hearing
Upon receipt of a submission
the Agency shall
commence its
review.
Within
5 days after making
a determination that
a
submission meets the requirements of Section 310.542, the Agency
shall:
a)
Issue
a public notice of request for approval
of the
submission;
1)
This public notice
shall
be circulated
in
a manner
designed
to
inform interested
and potentially
interested persons of the submission.
Procedures
for the
circulation
of
public
notice
shall
include:
A)
Mailing
notices of the
request
for approval of
the submission
to:
i)
Federal agencies as designated by USEPA;
ii)
Regional planning agencies which
participate
in
development
of
water
quality
management
plans;
and
iii) Any other person or group who has
requested
individual
notice,
including
those on appropriate mailing
lists; and
B)
Publication of
a notice of request for
approval
of
the
submission
in
the
largest
daily newspaper within the jurisdiction(s)
served by the
POTW.
2)
The public notice shall provide
a period
of not
less than
30 days following the date of the public
79-657

—34C—
notice during which
time interested persons may
submit
their written views on the submission.
3)
All written comments submitted during the
30 day
comment
period
shall
be
retained
by the Agency and
considered
in the decision on whether or
not to
approve the submission.
The period
for comment may
be extended at the discretion of the Agency; and
b)
Provide
an
opportunity
for
the
applicant, any affected
State,
any
interested
State
or
federal
agency,
person
or
group
of
persons
to
request
a
public
hearing
with
respect
to the submission.
1)
This request for public hearing
shall
be filed
within
the 30 day
(or extended) comment period
described
in subsection (a)(2)
and shall
indicate
the
interest of the person filing such request and
the reasons why a hearing
is warranted.
2)
The Agency shall hold
a hearing
if the POTW so
requests.
In addition,
a hearing will
be held
if
there
is
a significant public
interest
in issues
relating
to whether
or not the submission should be
approved.
Instances of doubt should be resolved
in
favor of holding the hearing.
3)
Public notice of a
hearing
to consider
a submission
and
sufficient
to inform interested parties of the
nature of the hearing
and
the
right
to
participate
shall
be published
in the same newspaper as the
notice of the original request
for
approval
of
the
submission under
subsection (a)(l)(B).
In
addition, notice of the hearing shall
be sent
to
those
persons requesting
individual
notice.
(Board
Note:
Derived
from 40 CFR 403.11(b)
(1986))
Section 310.543
Agency Decision
At the end of the
30 day
(or extended) comment period
and within
the
90 day
(or extended)
period provided for
in Section 310. 541,
the Agency shall approve or deny the submission based upon the
evaluation
in Section
310. 541 and taking into consideration
comments
submitted
during
the
comment
period
and
the
reocrd
of
the public hearing,
if held.
Where the Agency makes a
determination
to deny the request, the Agency shall
so notify the
POTW and each person who has requested
individual notice.
This
notification shall include suggested modifications and the Agency
may allow the requestor additional
time to bring
the submission
into compliance with applicable requirements.
(Board Note:
Derived from 40 CF? 403.11(c)
(1986))
79-658

—3SC—
Section 310. 544
USEPA Objection
The Agency shall not approve any pretreatment program
to which
USEPA objects pursuant
to 40 CFR 403.11(d)
(1986).
The P0Th may
contest such an objection only as provided
by USEPA rules and
procedures.
(Board Note:
Derived
from 40 CFR 403.11(d)
(1986))
Section 310. 545
Notice of
Decision
The Agency shall
notify those persons who submitted comments and
participated
in the public hearings,
if held, of the approval or
disapproval
of the
submission.
In addition, the Agency shall
cause
to be published
a notice of approval or disapproval
in the
same
newspaper
as
the
original
notice
of
request
for
approval
of
the submission
was published.
(Board Note:
Derived
from 40 CFR 403.11(e)
(1986))
Section 310.546
Public Access
to Submission
The Agency shall ensure that the submission
and
any comments upon
such submission
are available
to the public
for inspection
and
copying.
(Board Note:
Derived
from 40 CFR 403.11(f)
(1986))
Section
310. 547
Appeal
Any
final
Agency
action
refusing
to
approve,
or approving with
conditions,
a pretreatment program, may be appealed
to
the Board
as part of an appeal
of the Agency’s action on the NPDES permit
application.
SUBPART F:
REPORTING RECUIREMENTS
Section
310.601
Definition
of
Control
Authority
The term “Control Authority”
as
it is used
in this Subpart refers
to:
a)
The POTW if the POTW’s submission
for
its pretreatment
program (Section 310.110)
has been
approved
in
accordance with the requirements of Section 310.540
through 310.546; or,
b)
The
Agency,
if the submission has not been approved.
(Board
Note:
Derived from
40 CFR 403.12(a)
(1986))
Section 310.602
Baseline Report
Within the time limits specified
in subsection
(h), existing
79-659

—36C—
industrial
users
subject
to
such
categorical
pretreatment
standards and currently discharging
to or scheduled
to discharge
to
a POTW shall submit
to the control authority
a report which
contains
the
information
listed
in subsections
(a)
through (g).
New sources
shall submit
to the control authority
a report which
contains
the information listed
in subsections
(a)
through (e):
a)
Identifying
information.
The user
shall submit the name
and address of the facility including
the name of the
operator
and owners;
b)
Permits.
The user
shall submit
a list of any
environmental
control
permits
held
by
or
for
the
facility;
c)
Description
of
operations.
The
user shall submit a
brief description of the nature, average rate of
production
and
standard industrial classification (SIC
Code)
of the operations(s) carried out by such
industrial
user.
This description should
include
a
schematic process diagram which indicates points of
discharge
to
the POTW from the regulated processes.
d)
Flow measurement.
The user shall
submit information
showing the measured average daily and maximum daily
flow,
in gallons per day,
to the POTW from each of the
following:
1)
Regulated process streams;
and
2)
Other
streams
as
necessary
to
allow
use
of
the
combined wastestream formula of Section 310. 233.
(See subsection (e)(5)).
The control authority may
allow for verifiable estimates of these
flows
where
justified by cost or feasibility considerations.
e)
Measurement of pollutants.
1)
The
user shall
identify the pretreatment standards
applicable
to each regulated process;
2)
In
addition,
the
user
shall
submit
the
results
of
sampling and analysis identifying
the nature and
concentration
(or mass, where required by the
standard
or control authority)
of regulated
pollutant.s
in the discharge from each regulated
process.
Both daily maximum and average
concentration (or mass, where required) shall
be
reported.
The sample
shall
be representative of
daily operations.
3)
Where
feasible, samples must be obtained
through
the
flow
proportional
composite
sampling
techniques
specified
in the applicable categorical
79-660

—37C—
pretreatment standard.
Where composite sampling is
not feasible,
a grab sample
is acceptable.
4)
Where the flow of the stream being sampled
is less
than or
equal
to 950,000 liters/day (approximately
250,000 gpd),
the
user must
take three
samples
within
a two—week period.
Where
the flow of the
stream being sampled
is greater than 950,000
liters/day (approximately 250,000
gpd),
the
user
shall
take six samples within a two—week period;
5)
Samples
shall
be taken
immediately.downstream from
pretreatment facilities
if such exist or
immediately downstream from the regulated process
if no pretreatment exists.
If other
wastewaters
are mixed with the regulated wastewater prior
to
pretreatment the user
shall measure the flows and
concentrations necessary to allow use of the
combined wastestream formula of Section 310.233
in
order
to evaluate compliance with the pretreatment
standards.
Where
an alternate concentration or
mass limit has been calculated
in accordance with
Section
310.233,
this
adjusted
limit
along
with
supporting data shall
be submitted
to the control
authority;
6)
Sampling and analysis shall be performed
in
accordance with the techniques prescribed
in
40 CFR
136, incorporated by reference
in 35 Ill.
Adm. Code
307.1003.
When
40 CFR 136 does not contain
sampling
or analytical
techniques for the pollutant
in question, or where USEPA has determined that
sampling
and analysis techniques are inappropriate
pursuant to 40 CFR 403.12(b),
sampling and analysis
shall
be performed by using validated analytical
methods
or
any
other
applicable
sampling
and
analytical procedures,
approved by the Agency,
including procedures suggested by the
P0Th
or
other
parties;
7)
The control authority may allow the submission of a
baseline report which utilizes only historical data
so long as the data provides information sufficient
to determine
the need
for
industrial pretreatment
measures;
8)
The baseline report shall
indicate the
time, date
and place of sampling, and methods of analysis, and
shall certify that such sampling and analysis
is
representative of normal work cycles and expected
pollutant discharges
to
the POTW.
f)
Certification.
A statement, reviewed by an authorized
representative of the
industrial
user
(as defined
in
79-661

—38C—
Sectin 310.633)
and certified
to by
a qualified
professional, indicating whether pretreatment standards
are being met on
a consistent basis,
and,
if not,
whether additional operation and maintenance
(0 and M)
and/or additional pretreatment
is required for the
industrial
user
to
meet
the
pretreatment
standards
and
requirements; and
g)
Compliance schedule.
If
additional
pretreatment
and/or
0 and M will be required to meet the pretreatment
standards;
the shortest schedule by which the
industrial
user will provide such additional pretreatment
and/or C
and
M.
The completion date
in this schedule shall not
be
later
than
the
compliance
date
established
for
the
applicable pretreatment standard.
1)
Where
the
industrial
user’s
categorical
pretreatment standard has been modified by the
combined wastestream
formula
(Section 310.233),
and/or
a
fundamentally
different
factors
determination
(Subpart
E)
at the time the
user
submits the report required by this Section, the
information required by subsections
(f)
and
(g)
shall pertain
to
the modified
limits.
2)
If
the
categorical
pretreatment standard
is
modified
by the combined wastestream formula
(Section 310.233),
and/or
a fundamentally different
factors determination (Subpart
E)
after
the user
submits
the
report
required
by
this
Section,
any
necessary amendments to
the information requested
by subsections
(f)
and
(g)
shall
be submitted by
the user to
the control authority within 60 days
after
the
modified
limit
is
approved.
h)
Deadlines for existing
industrial
users.
1)
For standards adopted by USEPA prior
to
authorization of the Illinois pretreatment program,
baseline reports must be submitted pursuant
to 40
CFR 403.12(b)
(1986).
2)
For standards adopted by USEPA after authorization
of the Illinois pretreatment program, baseline
reports
for existing sources are due within 180
days after
the Board adopts or incorporates
a
categorical pretreatment standard, or
180 days
after
the
final
administrative
decision
made
upon
a
category determination submission under
Secton
310.221(d),
whichever
is
later.
(Board Note:
Derived
from
40 CFR 403.12(b)
(1986))
Section
310.603
Compliance
Schedule
79.662

—39C—
The following conditions apply to the schedule required by
Section 310.602(g):
a)
The
schedule shall
contain increments of progress
in the
form of dates
for the commencement and completion of
major events leading
to the construction and operation
of
additional
pretreatment
required
for
the
industrial
user
to meet the applicable categorical pretreatment
standards
(e.g., hiring
an engineer, completing
preliminary plans, completing
final plans, executing
contract
for major components, commencing construction,
completing construction, etc.).
b)
No
increment referred
to
in subsection
(a)
shall exceed
9 months.
c)
Not later
than 14 days following each date in the
schedule and the
final date for compliance,
the
industrial user shall
submit
a progress report to the
control authority including,
at
a minimum, whether or
not
it complied with the increment of progress to be met
on such date and,
if
not,
the date on which
it expects
to comply with this increment of progress, the reasons
for delay and the steps being taken by the industrial
user to return
the construction
to
the schedule
established.
In no event
shall more than
9 months
elapse between such progress reports to
the control
authority.
(Board Note:
Derived from 40 CFR 403.12(c)
(1986))
Section
310.604
Report on Compliance with Deadline
Within 90 days following the date
for final
compliance with
applicable categorical pretreatment standards or,
in the case of
a new source following commencement of the introduction of
wastewater
into the
POTW,
any industrial user subject
to
pretreatment standards and requirements shall
submit to the
control authority
a report
indicating the nature and
concentration of all pollutants
in the discharge from the
regulated process which are limited by pretreatment standards and
requirements and the average and maximum daily flow for these
process units
in the
industrial user which are limited by such
pretreatment standards and requirements.
the report shall state
whether the applicable pretreatment standards or requirements are
being met on
a consistent basis and,
if not, what additional
0
and M and/or pretreatment
is necessary to bring the industrial
user into compliance with the applicable pretreatment standards
or requirements.
This statement shall be signed by an authorized
representative of the
industrial
user, as defined
in Section-
310.633,
and certified
to by a qualified professional.
(Board Note:
Derived
from 40 CFR 403.12(d)
(1986))
79-663

—40C—
Section 310.605
Periodic Reports on Compliance
a)
Any industrial
user subject
to
a categorical
pretreatment
standard,
after
the
compliance
date
of
such
pretreatment
standard,
or,
in
the
case
of
a
new
source,
after commencement of the discharge into the P0Th,
shall
submit to
the control authority during the months of
June and December, unless required more frequently
in
the pretreatment standard
or by the control authority,
a
report indicating
the nature and concentration of
pollutants
in
the effluent which are limited by such
categorical pretreatment standards.
In addition, this
report shall
include
a record of measured
or estimated
average
and
maximum
daily
flows
for
the
reporting
period
for
the discharge reported
in Section 310.602(d), except
that the control authority may require more detailed
reporting of flows.
In consideration of such factors as
local high or low flow rates, holidays, budget cycles,
etc.,
the control authority may alter
the months during
which the
above reports are
to be submitted.
b)
Where the control
authority has imposed mass limitations
on
industrial users as provided by Section 310.232, the
report required by subsection
(a)
shall
indicate the
mass of pollutants regulated by pretreatment standards
in the discharge from the industrial
user.
(Board Note:
Derived from 40 CFR 403.12(e)
(1986)
Section 310.606
Notice of Slug Loading
The
industrial user shall
notify the POTW immediately of any slug
loading, as defined by Section 310.202 and 35 Ill.
Adm. Code
307.1101, by the industrial
user.
(Board Note:
Derived from 40 CFR 403.12(f)
(1986))
Section 310.610
Monitoring
and Analysis
The reports required
in Section 310.602(e), 310.604 and 310.605
shall contain the results of sampling and analysis of the
discharge, including the flow and the nature and concentration,
or
production and mass where requested by the control
authority,
of pollutants contained
in
the discharge which are limited by the
applicable pretreatment standards.
All analyses shall
be
performed
in accordance with procedures contained in 40 CFP 136,
incorporated by reference
in
35
Ill.
Adm.
Code 307.1003, or with
any other
test procedures approved by the Agency.
Sampling shall
be performed
in accordance with the techniques approved by the
Agency.
Where 40 CFR 136 does not include sampling
or analytical
techniques
for
the pollutants
in question,
or where
USEPA has
determined pursuant
to 40 CFR 403.12(b)
that sampling and
analytical techniques
are inappropriate, sampling and analyses
79.664

—41C-
shall be performed using validated analytical methods or any
other
sampling and analytical procedures, approved
by the Agency,
including procedures suggested by the POTW or other persons.
(Board Note:
Derived
from 40 CFR 403.12(g)
(1986))
Section 310.621
Compliance Schedule for
POTW’s
The following conditions
and reporting requirements shall apply
to
the
compliance
schedule
for
development
of
an
approvable
POTW
pretreatment
program
required
by
Sections
310.501
through
310.
510.
a)
The schedule shall contain increments of progress
in the
form of dates
for
the commencement and completion of
major
events
leading
to
the
development
and
implementation of
a POTW pretreatment program (e.g.,
acquiring required authorities, developing funding
mechanisms, acquiring equipment);
b)
No
increment referred
to
in
Section 310.621(a)
shall
exceed nine months;
c)
Not later
than 14 days following each date
in
the
schedule
and
the final date
for compliance, the POTW
shall submit
a progress report to the Agency including
as
a minimum, whether
or
not
it complied with the
increment of progress to be met on such date
and, if
not,
the date
on which it expects
to comply with this
increment of progress, the reason for delay, and the
steps taken by the P0Th
to return
to the schedule
established.
In
no event
shall more than nine months
elapse between such progress reports
to the Agency.
(Board Note:
Derived
from 40 CFR 403.12(h)
(1986))
Section 310.631
Signatory Requirements for
Industrial
User
Reports
The reports required by Sections 310.602,
310.604 and 310.605
must be signed by
an authorized representative of the industrial
user.
An authorized
representative is:
a)
A principal executive officer of at least the level of
vice president,
if the industrial
user submitting
the
reports required by Sections 310.602,
310.604 and
310.605
is
a corporation.
b)
A general partner
or proprietor,
if the industrial
user
submitting
the report required
by Sections
310.602,
310.604 and
310.605
is a partnership or
sole
proprietorship,
respectively.
c)
A duly authorized representative of the
individual
79.665

—42C—
designated
in subsections
(a) or
(b),
if such
representative
is responsible for the overall operation
of the facility from which the indirect discharge
originates.
(Board Note:
Derived from 40 CFR 403.12(i)
(1986))
Section 310.632
Signatory Requirements
for POTW Reports
Reports submitted to the Agency by the POTW
in accordance with
Section 310.621 must be
signed by
a principal executive officer,
ranking elected official
or other duly authorized employee
if
such employee is responsible
for overall operation of the POTW.
(Board Note:
Derived
from 40 CFR 403.12(j)
(1986))
Section 310.633
Fraud
and False Statements
The
reports
required
by
Sections
310.602,
310.604,
310.605
and
310.621
are
subject
to the provisions of 18 U.S.C.
1001 relating
to fraud
and
false
statements and
the provisions of Section
309(c) (2)
of the
CWA
governing
false statements,
representations
or certifications in reports required under
the
G’Th,
and
to the
provisions of
Title XII of the Act.
(Board Note:
Derived from 40 CFR 403.12(k)
(1986))
Section 310.634
Recordkeeping Requirements
a)
Any industrial
user
and POTW subject to the reporting
requirements established
in this
Subpart
shall
maintain
records of all information resulting from any monitoring
activities required by this
Subpart.
Such records shall
include for
all samples:
1)
The date, exact place, method
and time of sampling,
and the names of the person or persons taking the
samples;
2)
The
dates
analyses
were
performed;
3)
Who
performed
the
analyses;
4)
The analytical
techniques/methods use; and
5)
The results of such analyses.
b)
Any industrial
user or POTW subject
to the reporting
requirements established
in this Subpart shall be
required
to retain
for
a minimum of
3 years any records
of monitoring activities and results
(whether or
not
such monitoring activities are required by this Section)
and shall make such records available
for inspection and
copying
by the Agency
(and
POTW
in the case of an
79-666

—43C--
industrial
user).
This
period
of
retention
shall
be
extended during
the course of any unresolved litigation
regarding the
industrial
user or
POTW or when requested
by the Agency.
c)
Any POTW to which reports are submitted by an
industrial
user
pursuant
to
Sections
310.602,
310.604
and
310.605
shall
retain
such
reports
for
a
minimum
of
3
years
and
shall make such reports available for
inspection
and
copying by the Agency.
This period
of retention shall
be extended during the course of any unresolved
litigation regarding the discharge of pollutants by the
industrial
user or the operation of the POTW
pretreatment program
or when requested by the Agency.
(Board Note:
Derived from 40 CFR 403.12(1)
(1986))
SUBPART
C:
FUNDAMENTALLY DIFFERENT FACTCRS
Section
310.701
Definition of Requester
The
term “requester” means
an industrial user or
a POTW or other
interested person seeking
a fundamentally different factors (FDF)
determination
from
the
limits
specified
in
a
categorical
pretreatment standard.
(Board Note:
Derived
from 40 CFR 403.13(a)
(1986))
Section
310.702
Purpose and Scope
It
may
be
necessary
on
a
case—by—case
basis
to
adjust
the
limits
in categorical pretreatment standards, making
them either more or
less stringent, as they apply to
a certain
industrial user within
an industrial category or subcategory.
This will only be done if
data specific
to that industrial
user indicates
it presents
factors fundamentally different
from those considered by USEPA
in
developing
the limit at issue.
Any
interested person believing
that factors relating
to
an industrial user
are fundamentally
different
from the
factors considered during development of a
categorical pretreatment standard applicable
to that
user and
further, that the existence of those factors justifies
a
different discharge limit than specified
in the applicable
categorical pretreatment standard, may request
an
FDF
determination under this
Subpart.
Such
a determination
proceeding may be
initiated by the Agency also.
(Board Note:
Derived from 40 CFR 403.13(b)
(1986))
Section 310.703
Criteria
a)
General criteria.
A request
for
an FDF determination
shall
be approved only if:
1)
There
is an applicable categorical pretreatment
79.667

—44C—
standard which specifically controls the pollutant
for which alternative limits have been requested;
and
2)
Factors relating
to the discharge controlled by the
categorical pretreatment standard are fundamentally
different from the factors considered by USEPA in
establishing the
standards;
and
3)
The request for
an FDF determination is made in
accordance with the procedural requirements
in
Sections 310.711 and 310.712.
b)
Criteria applicable
to less stringent limits.
An FDF
determination
request
for
the establishment of limits
less
stringent
than
required
by
the
standard
shall
be
approved only if:
1)
The alternative limit requested
is no less
stringent than justified by the
fundamental
difference;
2)
The alternative limit will not result
in
a
violation of prohibitive discharge standards
prescribed by or established under
Section 310.201
through
310.213, or
35
Ill.
Adm.
Code 307;
3)
The
alternative
limit
will
not
result
in
a
non—
water quality environmental
impact (including
energy requirements) fundamentally more adverse
than the impact considered during development of
the pretreatment standards; and
4)
Compliance with the standards
(either by using the
technologies upon which the standards are based
or
by using other control alternatives) would result
in
a non—water quality environmental
impact
(including
energy
requirements)
fundamentally
more
adverse
than
the
impact
considered
during
development
of
the
standards.
c)
Criteria applicable
to more stringent limits.
An FDF
determination
request
for
the
establishment
of
limits
more stringent than required by the standards shall
be
approved only if:
1)
The alternative limit request
is no more stringent
than justified by the fundamental difference;
and
2)
Compliance with the alternative limit would not
result
in
a non—water quality environmental impact
(including energy requirements) fundamentally more
adverse
than the impact considered during
development of the standards.
79-668

—45C—
(Board
Note:
Derived from
40 CFR 403.13(c)
(1986))
Section 310. 704
Fundamentally Different
Factors
Factors which may be considered fundamentally different are:
a)
The nature or quality of pollutants contained
in
the raw
waste load of the user’s process wastewater;
b)
The
volume of the
user’s process wastewater and
effluent discharged;
c)
Non—water
quality
environmental
impact
of
control
and
treatment
of
the
user’s
raw
waste
load;
d)
Energy requirements of the application of control
and
treatment technology;
e)
Age, size,
land availability and configuration as they
relate
to the user’s equipment or
facilities; processes
employed;
process
changes;
and
engineering
aspects
of
the
application
of
control
technology;
and,
(Board
Note:
Derived
from
40
CFR
403.13(d)
(1986))
Section
310.705
Factors
which
are
Not Fundamentally Different
A FDF request
or portion of such
a request under
this Subpart
shall not be granted on any of the following grounds:
a)
The feasibility of installing
the required waste
treatment equipment within the time the
CWA
allows;
b)
The assertion that the standards cannot be achieved with
the appropriate waste
treatment facilities installed,
if
such assertion
is not based
on factors listed
in
Section
310. 704.
c)
The
user’s
ability
to
pay
for
the
required
waste
treatment;
or
d)
The
impact
of
a
discharge
on
the
quality
of
the
POTW’s
receiving waters.
(Board Note:
Derived
from 40 CFR 403.13(e)
(1986))
Section 310.706
More Stringent State Law
a)
The Agency shall not grant FDF determinations with
respect
to more stringent pretreatment standards adopted
pursuant
to independent
Board
authority (35 Ill. Adm.
Code 307.1102 and 307.1103).
79.669

—46C—
b)
Nothing
in this Subpart shall be construed
to
impair the
right of any POTW to impose more stringent limitations
pursuant
to Sections 310.210 and
310.211.
(Board
Note:
Derived
from 40 CFR 403.13(f)
(1986))
Section
310.711
Application
Deadline
a)
Request for
an FDF determination and supporting
information must be submitted
in writing
to the Agency.
b)
In order
to
be considered,
requests for
FDF
determinations must be submitted within the following
time limits:
1)
Prior
to authorization of the Illinois program, FDF
requests must be directed
to USEPA pursuant
to
40
CFR 403.13
(1986).
2)
For standards adopted by USEPA after authorization
of the Illinois pretreatment program,
the user
shall
request
and
FCF
determination
within
180
days
after
the Board adopts or incorporates the standard
by reference unless the
user has requested
a
category determination pursuant to Section 310. 221.
c)
Where
the
user
has requested
a category determination
pursuant
to Section 310.221,
the user may elect
to await
the results of the category determination before
submitting
a
request
for
an
FDF
determination.
Where
the user so elects, the user
shall
submit
the request
within
30 days after
a
final decision has been made on
the categorical determination pursuant
to Section
310.221(d).
(Board Note:
Derived from 40 CFR 403.13(g)
(1986))
Section
310.712
Contents of FDF Request
Written
requests
for
an
FDF
determination
must
include:
a)
The name and address of the person making the request;
b)
Identification
of
the
interest
of the requester which
is
affected by the categorical pretreatment standard
for
which the
FDF determination
is requested;
c)
Identification of the PCTW currently receiving the waste
from the industrial
user for which alternative discharge
limits are requested;
d)
Identification
of
the
categorical
pretreatment
standards
which
are
applicable
to
the
industrial
user;
79.670

—47C—
e)
A list of each pollutant
or pollutant parameter for
which
an alternative discharge limit is sought;
f)
The alternative discharge limits proposed by the
requester
for each pollutant or pollutant parameter
identified
in subsection
(e);
g)
A description of the industrial user’s existing
water
pollution control
facilities;
h)
A schematic
flow representation of the industrial
user’s
water
system including water
supply, process wastewater
systems, and points of discharge; and
i)
A statement of facts clearly establishing why the
request
for
an
FDF
determination
should
be
approved,
including detailed support data, documentation and
evidence
necessary
to
fully
evaluate
the
merits
of
the
request,
e.g.,
technical
and
economic data collected by
USEPA
and
used
in
developing
each
pollutant
discharge
limit
in the pretreatment standard.
(Board Note:
Derived from 40 CFR 403.13(h)
(1986))
Section 310.713
Deficient Requests
The Agency shall
act only on written requests of FDF
determinations which contain all of the information required.
The Agency shall notify persons who have made incomplete
submissions
that their
requests are deficient
and that,
unless
the
time period
is extended, they have thirty days
to remedy the
deficiency.
If the deficiency is not corrected within the time
period allowed,
the Agency shall deny the
request for
an FDF
determination.
(Board Note:
Derived from 40 CFR 403.13(i)
(1986))
Section
310.714
Public Notice
Upon receipt of a complete request, the Agency shall provide
notice of receipt, opportunity to review the submission
and
opportunity to comment.
a)
The public notice shall
be circulated
in
a manner
designed
to inform
interested
and potentially interested
persons of the request.
Procedures
for the circulation
of public notice
shall
include mailing notices
to:
1)
The POTW into which the industrial user requesting
the FDF determination discharges;
2)
Adjoining states whose waters may be affected; and
3)
Federal agencies as designated by USEPA;
79-671

—4BC—
4)
Regional
planning
agencies
which
participate
in
development
of
water
quality
management
plans;
and
5)
Any other person or group who has requested
individual notice, including those on appropriate
mailing
lists;
and
b)
The public notice
shall provide for
a period not less
than
30
days
following
the
date
of
the
public
notice
during
which
time
interested
persons
may
review
the
request and submit their written views on the request.
c)
Following
the
comment
period,
the
Agency
shall
make
a
determination
upon
the
request
taking
into
consideration
any
comments
received.
Notice
of
the
final
decision
shall
be
provided
to
the
requester
(and
the
industrial
user for which the variance
is requested, if different),
the
POTW into which the industrial
user discharges and
all persons who submitted comments on the request.
(Board
Note:
Derived
from
40
CFR
403.13(j)
(1986))
Section
310.721
Agency
Review
of
FDF
Requests
a)
Where the Agency finds that fundamentally different
factors do not exist,
it shall deny the request and
notify
the
requester
(and
industrial
user
where
they
are
not
the
same)
and
the
POTW
of
the
denial.
b)
If the Agency finds that fUndamentally different factors
do
exist,
it
shall
forward
the
request,
with
a
recommendation
that
the
request
be
approved,
to
USEPA.
(Board
Note:
Derived
from
40
CFR
403.13(k)
(1986))
Section
310. 722
USEPA
Review
of
FDF
Requests
a)
USEPA will deny or approve the request
for an
FDF
determination
as
provided
in
40
CFR
403.13(1)
and
(in)
(1986).
b)
The Agency shall not grant an FDF request
unless
it has
been
approved
by
USEPA.
C)
Appeal.
1)
The requester may appeal
to the Board any finding
by
the
Agency
that
FDF
do
not
exist.
2)
If
USEPA
refuses
to
approve
a
request
forwarded
by
the
Agency,
the
requester
may
contest
the
decision
only as allowed by USEPA.
79.672

—49C—
(Board
Note:
Derived from 40 CFR 403.13(1)
and
(m)
(1986))
SUBPART
H:
ADJUSTMENT FOR POLLUTANTS
IN INTAKE
Section 310.801
Net/Gross Calculation by USEPA
USEPA may adjust categorical pretreatment standards
to reflect
the presence of
pollutants
in the
industrial user’s intake water
as
provided
in 40 CFR
403.15
(1986).
SUBPART
I:
UPSETS
Section
310.901
Definition
For the purposes of this Subpart, “upset” means an exceptional
incident
in which there
is unintentional
and temporary
noncompliance with categorical
pretreatment standards because of
factors beyond the reasonable control of the
industrial
user.
An
upset does not include noncompliance
to the extent caused by
operational error,
improperly designed treatment facilities,
inadequate
treatment facilities, lack of preventive maintenance
or careless
or
improper operation.
(Board Note:
Derived
from 40 CFR 403.16(a)
(1986))
Section
310.902
Effect of
an Upset
An upset
shall constitute
an affirmative defense
to
an action
brought
for noncompliance with categorical pretreatment standards
if the requirements of Section 310.903 are met.
(Board Note:
Derived from 40 CFR 403.16(b)
(1986))
Section 310.903
Conditions Necessary for an Upset
An
industrial
user who wishes
to establish the affirmative
defense of upset shall demonstrate, through properly signed,
contemporaneous operating logs,
or other relevant evidence,
that;
a)
An
upset
occurred
and the
industrial user can identify
the specific cause(s)
of
the upset;
b)
The facility was at the time being operated
in
a prudent
and
workmanlike
manner
and
in
compliance
with
applicable
operation
and
maintenance
procedures;
c)
The
industrial user has submitted the following
information to the POTW and control authority within 24
hours of becoming aware of the upset (if this
information
is
provided
orally,
a
written
submission
must be provided within five days);
1)
A
description
of
the
indirect
discharge
and
cause
79-673

—500—
of noncompliance;
2)
The
period
of
noncompliance,
including
exact
dates
and times
or,
if not corrected, the anticipated
time
the
noncompliance
is
expected
to
continue;
3)
Steps being
taken and/or planned
to reduce,
eliminate
and
prevent
recurrence
of
the
noncompliance.
(Board Note:
Derived from 40 CFR 403.16(c)
(1986))
Section 310.904
Burden of Proof
In any enforcement proceeding
the industrial
user seeking
to
establish the occurrence of an upset
shall have the burden of
proof.
(Board Note:
Derived from 40 CFR 403.16(d)
(1986))
Section 310.905
Reviewability of Claims of Upset
In
the
usual exercise of prosecutorial discretion, Agency
enforcement personnel should review any claims that non-
compliance was caused by an upset.
No determinations made
in the
course of the review constitute
final Agency action subject
to
judicial
review.
Industrial
users will have the opportunity for
a
judicial
determination
on
any
claim
of
upset
only
in
an
enforcement
action
brought
for
noncompliance
with
categorical
pretreatment standards.
(Board Note:
Derived from 40 CFR 403.16(e)
(1986))
Section
310.906
User Responsibility
in Case of Upset
The industrial user shall
control production or
all discharges to
the extent necessary to maintain compliance with categorical
pretreatment standards upon reduction, loss
or
failure of its
treatment
facility
until
the
facility
is restored
or
an
alternative
method
of
treatment
is
provided.
This requirement
applies
in the situation where, among other
things, the primary
source of power
of the treatment facility is reduced, lost or
fails.
(Board Note:
Derived from 40 CFR 403.16(f)
(1986))
79.674

—510-
1,
Dorothy
M.
Cunn,
Clerk of the Illinois Pollution Control
the
/~C~day
of
____________________
______
_____________________,
1987,
by
a
vote
Board, hereby certify
above Order was adopted on
of
_________
Clerk
Dorothy M
Illinois Pollution Control Board
79-675

Back to top