ILLINOIS POLLUTION CONTROL BOARD

rebruary 27,

1992

IN THE MATTER OF:

)

pM-1O EMISSION LIMITS FOR THE

)

MCCOOK

AND

LAKE

CALUMET

AREAS

)

OF

COOK

COUNTY,

ILLINOIS,

AND

)

R91-22

THE

GRANITE

CITY

AREA

OF

)

(Rulemaking)

MADISON COUNTY, ILLINOIS:

)

AMENDMENTS TO 35 ILL.ADM.CODE

)

PARTS 211

AND

212

)

proposed

~il~

Second Notice.

OPINION

AND

ORDER OF THE BOARD

(by J. Theodore Meyer):

This matter is before the Board on the Illinois Environmental

protection

Agency’s

(Agency)

August

19,

1991

proposal.

The

proposal

is

intended

to

regulate

particulate

matter

with

an

aerodynamic

diameter

less

than

or

equal

to

a

nominal

10

micrometers,

which is known as PM1O.

This proposal is directed at

the McCook

and

Lake

Calumet

areas

of

Cook

County,

and

at

the

Granite City area of Madison County.

The proposal represents one

part of Illinois’s submittal

of

a complete state implementation

plan (SIP) for the control of PM-b

emissions.

Pursuant to Section

189 of the Clean Air Act, as amended

lfl 1990,

Illinois was to adopt

and submit its plan by November 15, 1991.

Procedural History

The Board accepted the proposal

for hearing

on August

22,

1991,

and sent the proposal to first notice on August

26,

1991.

The

proposal

was

first

published

in

the

Illinois

Register

on

September 20,

1991, at 15 Ill.Reg.

13627.

On September 30, 1991, the Agency moved to substantially amend

its proposal by adding

rules

necessary for the Granite City area to

show compliance.

On October

10,

1991,

the Board

granted that

motion to amend,

but noted that because of the complexity, of the

new proposal,

the

Illinois

Administrative

Procedure Act

(APA)

required that the entire proposal be

again published

for

first

notice.

(Ill.ReV.Stat.

1989,

ch.

12.7,

par.

1001 et seq.)

The

Board noted that returning to first notice would delay completion

of

the

rulemaking,

and

that there

was

no possibility

of

even

reaching

second

notice

before

the

November

15,

1991

federal

deadline.

As

it had pointed out

in

its August

22 and August 26

orders, the Board again stated that because the proposal was filed

on August

19,

1991,

Illinois

law made

it literally impossible,

since the day the proposal was filed, to meet the federal deadline.

The Board granted the Agency’s motion to amend, and stated that it

130—393

---

2

would send the proposal, as amended, to second first notice.

Also

on October 10, 1991, the Board found that no economic impact study

(EcIS) was necessary in this proceeding.

On October 22 and 23,

1991, the Agency filed two more motions

to amend the proposal.

The Board granted those motions to amend on

October

24,

1991.

At the Agency’s

request,

the Board

had not

submitted the paperwork necessary for publication of the second

first notice, issued by the Board on October 10, for publication in

the

Illinois

Register.

Therefore,

the

Board

integrated

the

language proposed

in

the

October

22

and

23

motions

with

the

language in the October

10

order.

This resulted in an amended

second first notice, which superseded the October 10 order.1

That

second

first notice

was published

in

the

Illinois Register

on

November 8,

1991, at

15 Il1.Reg.

15875, and on November 15,

1991,

at 15 Ill.Reg. 16564.

Another motion to amend was filed on October

30, 1991.

That motion to amend is granted, since the nature of the

proposed

amendments

do

not

require

a

separate

first

notice

publication.

Public hearings were held in Chicago on October 23,

1991,

and in Edwardsville on October 29,

1991.

A written public

comment period expired on December 30,

1991.

Proposal

The

United

States

Environmental

Protection

Agency

(USEPA)

established national ambient air quality standards

(NAAQS)

for PM-

10

in

1987.

The

24-hour

standard

is

150

ug/m3

and

the

annual

standard

is

50

ug/m3.

(52

Fed.Reg.

24634

(July

1,

1987).)

On

August 7,

1987, USEPA designated Cook and Madison Counties as Group

I areas for PM—b, because these areas had a 95

probability of not

attaining the PM-b

NAAQS.

(52 Fed.Reg.

29383

(August 7,

1987).)

The Clean Air Act,

as amended in 1990, requires Illinois to submit

a state implementation plan

(SIP)

for PM-b.

As discussed above,

the deadline

for that SIP submission to USEPA was November

15,

1991.

(42 U.S.C. §~7410, 7513(a).)

In

its

statement

of

reasons supporting

this

proposal,

the

Agency outlined its approach to this rulemaking.

When developing

its

SIP,

Illinois

must

assume

that

each

source will

emit

the

maximum amount of particulate matter allowed by regulation,

even

though most

facilities

in

Illinois

do

not

emit

to

the maximum

extent allowed by the Board’s regulations.

Therefore, the Agency

used existing Board regulations

as the basis for the control of

particulate matter.

The rules proposed in this rulemaking reflect

the levels of control which are already

in use by most affected

sources.

The proposed rules require

further control only where

specifically

needed

to

demonstrate

attainment

with

the

NAAQS.

Finally,

the

Agency

worked

closely

with

interested

parties,

1

For

further discussion

on the necessity

of

returning to

first notice,

see the Board’s October 24, 1991 order.

130—394

---

3

including affected facilities,

and with the Department of Energy

and Natural Resources (ENR) during the development of the proposal.

The Agency developed an inventory of emission sources in the

three

study

areas

(McCook,

Lake

Calumet,

and

Granite

City),

concentrating

on

quantifying

and verifying

the

emissions

from

industrial

activities.

(Ex.

D.)

Using those

inventories

as

a

basis, the Agency then performed dispersion modeling to study the

air

quality

in

the

three

areas.

(Ex.

E.)

Throughout

the

development of the proposal,

the Agency consulted with USEPA to

ensure

that

Illinois’

efforts

meet

federal

requirements

and

guidance.

The Agency

also

reviewed the regulatory development

efforts of other states, particularly Michigan, Indiana, Minnesota,

and Ohio.

The Agency then applied the data to develop the proposed

rules.

For point sources, the Agency has proposed a general limit

of 0.03 gr/scf, with alternative standards for a few sources..

The

Agency

contends that most process emission sources

in the three

areas are currently meeting the 0.03 gr/scf standard.

For fugitive

particulate matter emissions, the Agency proposed qpacity limits to

ensure that adequate control measures are applied.’

(Exs.

Fl, F2.)

Public Comments

The Board received a number of public comments on the October

24 second first notice proposal.

Comments were received from ENR

(P.C.# 3), Waste Management of Illinois, Inc.

(P.C.#4), the City of

Chicago (P.C.#5), the Department of Commerce and Community Affairs

(P.C. #6 and #17),

the Administrative Code Unit

(P.C. #7 and

#8),

Ford Motor Company

(P.C. #9), the Illinois Steel Group

(P.C.#10),

the Grain Companies

(P.C.#ll),

Reynolds Metals Company

(P.C.#l2),

Spectrulite Consortium,

Inc.

(P.C.#l3), Harding Lawson Associates

(P.C.#l4),

the Agency

(P.C.#l5,

#18),

and USEPA

(P.C.#16).3

The

Board

has

considered

all

of

these

comments,

as

well

as

the

testimony and exhibits received at the hearings,

in revising this

proposal for second notice.

Throughout

this

proceeding,

it

has

been obvious

that

the

Agency’s attempts to

involve interested parties,

and especially

affected sources, during the development of the proposal have been

very helpful

in resolving areas

of disagreement.

In

general,

affected sources feel that they can meet the proposed rules, and in

2

For a section—by-section discussion of the proposed rules,

as

submitted

by

the

Agency,

see

pages

17-28

of

the

Agency’s

statement

of

reasons,

and

the Agency’s

motions to

amend

filed

September30, October 22, October 23, and October 30,

1991.

~ The Agency

filed

supplemental

comments,

docketed as

P.C.

#18, with a motion for leave to file instanter on January 21, 1992.

Those supplemental comments include responses to the comments filed

by USEPA..

That motion to file instanter is granted.

130—395

---

4

many cases

are already

in compliance with those rules.

In

its

comments,

the Agency

agrees

with many

of

the

specific changes

suggested by

individual commenters.

The Board will not discuss

each of those changes in detail, but will make those changes as

proposed by the Agency in its comments.

(P.C#

15,

#18.)

However,

there

are

several

suggestions made by commenters

which the Agency opposes.

In particular,

the Agency contends that

suggestions made by Ford Motor Company (P.C.#9) do not improve the

proposed, rules,

and points out that USEPA also objects to Ford’s

suggestion that a State of Michigan measurement method for opacity

from roadways and parking areas be substituted in proposed Section

212.109.

The Board

finds that the responses

of the Agency

and

USEPA sufficiently address the suggestions made by Ford,

and will

not revise the rules

in response to those suggestions.

The Board

particularly points out that proposed Section 212.316(f)

will not

eliminate

Sections

212.122

and

212.123

in

the

three

areas.

Proposed Section

212.316(f)

applies only to fugitive emissions.

Sections

212.122

and

212.123

will

continue

to

apply

to

stack

emissions statewide.

The Agency also objects to Waste Management’s suggested change

to proposed Section 212.316(g) (5), which would require quarterly

reporting of occasions on which necessary fugitive control measures

are not implemented.

Waste Management maintains that quarterly

reporting is excessive for fugitive emissions from roadways,

and

contends that annual reporting would be no less environmentally

protective.

The

Agency

disagrees,

and

argues

that

quarterly

reporting is a vital part of its efforts to insure attainment of

the PN-1O standard.

The Board finds that quarterly reporting will

help

the

Agency

monitor

compliance,

and

is

both

economically

reasonable

and technically

feasible for affected sources.

The

Board will not propose changes to that reporting requirement.

The Illinois Steel Group proposed that language be added

to

Section

212.109 to address the variability of opacity readings.

The Steel Group suggests that new language

in the rule protect

a

source from enforcement if a violation is based on opacity readings

that are subject to variable interpretations.

The Agency strongly

objects to the proposed change,

and argues that Method

9 already

takes variability into account in assessing compliance.

The Board

declines to add language to Section 212.109

as proposed by the

Steel Group.

Federal Approvability

In its.statement

of reasons

supporting

this proposal,

the

Agency

indicated that USEPA had reviewed the proposal,

and that

based

on that

review,

the

Agency believed

that the

rules

are

federally approvable.

(Statement of reasons,

p.

15.)

The Agency

did recognize that the Clean Air Act requires that SIPs provide

r~ntinqency measures

to

be

undertaken

if

the

area

does

not

130—396

---

5

subsequently demonstrate compliance after the SIP is in place.

(42

U.S.C.

§7502.)

The

Agency

stated

that

USEPA

has

not

yet

interpreted these contingency requirements, so that It is. not known

what kinds of measures are required under this provision.

Jay

Bortzer,

Chief

of the

Regulation

Development

Section,

Air

and

Radiation Division of USEPA Region V1

testified at hearing that

general guidance on the contingency issue had only recently been

issued by USEPA,

and suggested that the

Board proceed with this

rulemaking.

Mr. Bortzer also testified that the approach used by

the Agen,cy in the proposed rules is acceptable to USEPA, and that

the proposed rules are the types of rules USEPA expects Illinois to

submit.

(Tr2,

pp

8—bl.)

USEPA

subsequently

submitted

more

detailed

comments

on

the

proposal

(P.C.#16),

and

the

Agency

responded-to those comments (PC.#b8).

Based on this information,

bhe

Board

believes

that

these

rules,

as

amended

today,

are

~ederally approvable.

Conclusions

Based upon its consideration of the testimony,

exhibits,

and.

comments received in this proceeding, the Board will propose these

rules for second notice.

The second notice proposal includes those

changes suggested by the Agency.

In Part 211, only one change has

been made:

a non—substantive change to the definition of “PM-b”

in Section 211.122.

Significantly more changes have been made to

the rules proposed in Part 212.

Some of these changes are non—

substantive clarifications, while others represent the agreements

of the Agency and individual affected sources.

Changes have been

made

to

the

following

sections:

212.109,

212.110,

212.210,

212.302, 212.309,

2l2.3b6, 212.324, 212.362, 212.425, 212.458, and

212.464.

These changes have generally been made as proposed by the

Agency

in

its

comments;

however,

the Board

has made some

non—

substantive changes to the language in the interests of clarity and

organization.

The

Board

finds

that these

proposed

rules

are

economically reasonable and technically feasible.

The Board also

finds that the proposed rules will demonstrate attainment with the

PM-b

NAAQS,

and are federally approvable.

ORDER

The Board hereby proposes the following amendments for second

notice.

The Clerk of the Board is directed to file these proposed

amendments with the Joint Committee on Administrative Rules.

TITLE

35:

ENVIRONMENTAL PROTECTION

SUBTITLE B:

AIR POLLUTION

CHAPTER I:

POLLUTION CONTROL

BOARD

SUBCHAPTER c:

EMISSION STANDARDS

AND

LIMITATIONS

FOR STATIONARY SOURCES

130—397

---

6

PART 211

DEFINITIONS

AND

GENERAL PROVISIONS

SUBPART A:

GENERAL PROVISIONS

ection

11.101

Incorporations by Reference

11.102

Abbreviations and Units

SUBPART B:

DEFINITIONS

ection

~ll.l21

Other Definitions

~l1.122

Definitions

~l1.AppendixA

Rule into Section Table

~1l.Appendix B

Section into Rube Table

WTHORITY:

Implementing Sections 9,

9.1 and 10 and authorized by

ection

27 of

the Environmental Protection Act

(Ill.

Rev.

Stat.

1989,

ch.

111½, pars.

1009,

1010 and 1027).

3OURCE:

Adopted

as

Chapter

2:

Air

Pollution,

Rule

20b:

)efinitions, R71—23,

4 PCB 191, filed and effective April 14, 1972;

amended in R74—2 and R75—5,

32 PCB 295, at 3 Ill.

Reg.

5,

p.

777,

effective February 3,

1979; amended in R78—3 and 4,

35 PCB 75 and

243, at 3 Ill. Reg. 30, p.

124, effective July 28, 1979; amended in

R80-5, at 7 Ill. Reg. 1244, effective January 21, 1983; codified at

7

Ill.

Reg.

13590;

amended

in R82—l

(Docket

A)

at

10

Ill.

Reg.

12624, effective July 7, 1986; amended in R85-21(A) at 11 Ill. Reg.

11747, effective June 29,

1987;

amended in R86—34 at 11 Ill.

Reg.

12267, effective July 10,

1987;

amended in R86—39 at lb Ill. Reg.

20804, effective December 14, 1987; amended in R82-14 and R86—37 at

12 Ill. Reg. 787, effective December 24, 1987; amended in R86—b8 at

12 Ill. Reg. 7284, effective April 8, 1988; amended in R86—10 at 12

Ill Reg.

7621,

effective April

lb,

1988;

amended in R88-23 at

13

Ill. Reg.

10862,

effective June 27,

1989;

amended in R89-8

at

13

Ill. Reg.

17457, effective January

1,

1990; amended in R 89-16(A)

at 14 Ill. Reg.

9l4b, effective May 23,

1990; amended in R88—30(B)

at 15

111.

Reg.

5223, effective March 28,

1991; amended in R88-l4

at

15 Ill. Reg. 7901, effective May 14,

1991; amended in R91—10 at

15 Ill .Reg.

____,

effective October 11, ‘1991; amended in R91—22

at

16 Ill.Reg.

_________,

effective

_________________

Section 2bl..10l

Incorporationsby Reference

The

following materials

are

incorporated

by

reference.

ThesE

incorporations do not include any later amendments or editions.

a)

“Evaporation Loss from Floating Roof Tanks,”

Americai

Petroleum Institute Bulletin 2517,

1962

b)

Ringelmann Chart,

Information ‘Circular 833

(Revision

o:

1C7718),

Bureau of Mines,

U.S.

Department of Interior

130—398

---

7

May 1,

1967

c)

Standard Industrial ClassificationManual, Superintendent

of Documents, Washington,

D.C.

20402,

1972

d)

American Society

for Testing and Materials,

1916 Race

Street, Philadelphia, PA 19103

A.S.T.M. D—86

A.S.T.M.

D—240—64

A.S.T.M.

D—323

A.S.T.M.

D—369—69

(1971)

A.S.T.M.

D—396—69

A.S.T.M.

D—900—55

A.S.T.M. D—975—68

A.S.T.M. D—1826—64

A.S.T.M. D—2015—66

A.S.T.M. D—2880—7l

~j

40 CFR 51.100

(1987)

(Source:

Amended at 16 Ill.Reg.

_______,

effective

_________

Section 211.122

Definitions

*IAccelacotavt:

a pharmaceutical coating operation which

consists of

a horizontally rotating perforated

‘drum in

which

tablets

are

placed,

a

coating

is

applied

by

spraying and the coating

is dried by the

flow of air

across the drum through the perforations.

llAccumulator~t:

The

reservoir

of

a

condensing

unit

receiving the condensate from a surface condenser.

“Acid Gases”:

For the purposes

of Section 9.4 of the

Environmental Protection Act

(the Act)

(Ill. Rev.

Stat.

1989,

ch.

111

½,

par.

1009.4),

hydrogen

chloride,

hydrogen fluoride and hydrogen bromide, which exist as

gases,

liquid mist,

or any combination thereof.

“Actual Heat Input”:

The quantity of heat prod~,.icedby

the combustion of fuel using the gross heating value of

the fuel.

“Aeration”:

The practice of forcing air through bulk

stored grain to maintain the condition of the grain.

“Afterburner”:

A device in which materials in gaseous

effluents are combusted.

“Air Dried Coating”:

Coatings that dry by the use of air

or forced air at temperatures up to 363.15°K (194°F).

130—399

---

8

“Air suspension coater/dryer”:

a pharmaceutical coating

operation which consists of vertical chambers in which

tablets or particles are placed, and a coating is applied

and then dried while the tablets,or particles are kept in

a fluidized state by the passage of air upward through

the chambers.

“Annual Grain Through—Put”:

Unless otherwise shown by

the

owner

or

operator,

annual

grain

through—put

for

grain—handling operations, which have been in operation

for three consecutive years prior to June 30, b975,

shall

be determined by adding grain receipts and shipments for

the three previous fiscal years and dividing the total by

6.

The

annual

grain

through-put

for

grain-handling

operations in operation for less than three consecutive

years prior to June

30,

1975,

shall be determined by

a

reasonable three—year estimate;

the owner

or operator

shall

document

the

reasonableness

of

his

three—year

estimate.

“Architectural

Coating”:

Any

coating

used

for

residential

or

commercial

buildings

or.

their

appurtenances, or for industrial buildings which, is site

applied.

“Asphalt”:

The dark—brown to black cementitious material

(solid, semisolid or liquid in consistency)

of which the

main constituents are bitumens which occur naturally or

as a residue of petroleum refining.

“Asphalt Prime

Coat”:

A ‘low-viscosity liquid asphalt

applied to an absorbent surface as the first of more than

one asphalt coat.

“Automobile”:

Any

first division motor vehicle as that

term is defined in the Illinois Vehicle Code

(Ill. Rev.

Stat.

1989,

ch.

95½, pars 1—100 et seq.).

“Automobile or Light-Duty Truck Manufacturing Plant”:

A

facility where parts

are manufactured

or finished

for

eventual inclusion into a finished automobile or light-

duty truck ready

for sale to vehicle dealers,

but not

including customizers, body shops and other repainters.

“Batch

Loading”:

The process

of loading

a

number of

individual parts at the same time for degreasing.

“Bead-Dipping”:

The dipping of an assembled tire bead

into a solvent—based cement.

130—400

---

9

“British Thermal Unit”:

The quantity of heat required to

raise one pound of water from 60°F to 61°F (abbreviated

btu).

“Bulk

Gasoline

Plant”:

Any

gasoline

storage

and

distribution facility that receives gasoline from bulk

-

gasoline terminals by delivery vessels and distributes

gasoline to gasoline dispensing facilities.

“Bulk

Gasoline

Terminal”:

Any

gasoline

storage

and

distribution facility that receives gasoline-by pipeline,

ship or barge, and distributes gasoline to bulk gasoline

plants or gasoline dispensing facilities.

“CanCoating”:

The application of a coating material to

a single walled container that is manufactured from metal

sheets thinner than 29 gauge (0.0141

in).

“Certified Investigation”:

A report signed by Illinois

Environmental

Protection

Agency

(Agency)’

personnel

certifying whether a grain—handling operation (or portion

thereof) or grain-drying operation is causing or tending

to cause air pollution.

Such report must describe the

signatory’s investigation, including a summary of those

facts on which he relies to certify whether the grain-

handling

or

grain—drying

operation

is

causing

or

threatening or allowing the discharge or emission of any

contaminant into the environment so as to cause or tend

to cause air pollution in Illinois,

either alone

or in

combination with contaminants from other sources, or so

as to violate regulations or standards adopted by the

Pollution Control Board

(Board) under the Environmental

Protection Act (Act).

The certified investigation shall

be open to

a

reasonable public

inspection and may be

copied upon payment of the actual cost of reproducing the

original.

“Choke Loading”:

That method of transferring grain from

the grain-handling operation to any vehicle for shipment

or delivery which precludes a free fall velocity of grain

from a discharge spout into the receiving container.

“Cleaning and Separating

Operation”:

That

operation

where foreign and undesired substances are removed from

the grain.

“Clear Coating”:

Coatings that lack color and opacity or

are transparent using the undercoat as a reflectant base

or undertone color.

“Closed Purge System”:

A system that is not open tç the

atmosphere and that is composed of piping, connections,

130—40 1

---

10

and,

if necessary,

flow inducing devices that transport

liquid or vapor from’ a piece or pieces of equipment to a

control

device,

or return the liquid or vapor

to the

process line.

“Closed Vent System”:

A system that is not open to the

atmosphere and that is composed ‘of piping,

connections,

and,

if necessary,

flow inducing devices that transport

gas or vapor from a piece

or pieces of equipment to

a

control device, or return the gas or vapor to the process

line.

“Coal Refuse”:

Waste products of coal mining, cleaning

and coal preparation operations containing coal, matrix

material, clay and other organic and inorganic material.

“Coating”:

For purposes of this Part, a coating includes

a

material

applied

to

a

substrate

for

decorative,

protective or other functional purposes.

Such material

shall include but not be limited to paints,

varnishes,

sealers, adhesives,

diluents and thinners.

“Coating Applicator”:

Equipment used to apply a surface

coating.

“Coating Line”:

An operation where a surface coating is

applied to

a material

and subsequently the coating is

dried and/or cured.

“Coating Plant”:

Any

building, structure or installation

that contains a coating line and which is located on one

or more contiguous or adjacent properties and which

is

owned or operated by the same person

(or by persons under

common control).

“Coil Coating”:

The application of a coating material to

any

flat metal

sheet

or

strip that comes

in

rolls or

coils.

“Cold Cleaning”:

The process of cleaning and removing

soils from surfaces by spraying, brushing,

flushing or

immersion while maintaining the organic solvent below its

boiling point.

Wipe cleaning is not included in this

definition.

“Complete Combustion”:

A process

in which

all carbon

contained in a fuel or gas stream is converted to carbon

dioxide.

“Component”:

Any

piece

of

equipment

which

has

the

potential to leak volatile organic mate~iabincluding,

but not limited to, pump seals,

compressor seals,

seal

130—402

---

11

oil

degassing vents,

pipeline

valves,

pressure relief

devices,

process

drains

and open ended

valves.

This

definition

excludes

valves

which

are

not

externally

regulated,

flanges,

and

equipment

in

heavy

liquid

service.

For purposes of 35 Ill. Adm. Code 2l5.Subpart

Q,

this definition also excludes bleed

ports

of gear

pumps

in

polymer

service.

“Concentrated

Nitric

Acid

Manufacturing

Process”:

Any

acid producing facility manufacturing nitric acid with a

concentration equal

to

or greater than

70 percent by

weight.

“Condensate”:

Hydrocarbon

liquid

separated

from

its

associated gasses which condenses due to changes in the

temperature or pressure and remains

liquid at standard

conditions.

“Condensible PM-b”:

PM-la formed immediately or shortly

after discharge to the atmosphere,

as measured by the

applicable test method

specified

in

35

Ill.

Adm.

Code

212.110.

Condensible

particulate

matter

exists

in

gaseous

and/or

vapor

form

prior

to

release

to

the

atmosphere,

e.g,

in the

stack,

and

forms

particulate

matter upon condensation when subject to conditions of

cooling and dilution in the atmosphere.

“Control

Device”:

Equipment,

such as an afterburner,

adsorber, scrubber, condenser, cyclone or baghouse used

to remove or prevent the emission of air-pollutants from

a contaminated exhaust stream.

For purposes of 35

Ill.

Adm. Code 215, Subpart Q, an enclosed combustion device,

vapor recovery system,

flare,

or closed container.

“Conveyorized Degreasing”:

The continuous process of

cleaning

and

removing

soils

from

surfaces

utilizing

either cold or vaporized solvents.

“Crude

Oil”:

A

naturally

occurring

mixture

which

consists of hydrocarbons and sulfur, nitrogen or oxygen

derivatives

of hydrocarbons

and which

is

a

liquid

at

standard conditions.

“Crude Oil Gathering”:

The transportation of crude oil

or condensate after custody transfer between a production

facility and a reception point.

“Crushing”:

The fragmentation of non—metallic minerals

by

a machine such as

a jaw,

ci’yratory,

cone,

roll,

rod,

mill,

hammermill, and impactor.

130—405

---

12

“Custody Transfer”:

The transfer of produced petroleum

and/or condensate after processing and/or treating in the

producing operations,

from storage

tanks

or automatic

transfer facilities to pipelines or any other forms of

transportation.

“Cutback Asphalt”:

Any

asphalt which has been liquified

by blending with petroleum solvents other than residual

fuel oil and has not been emulsified with water.

“Degreaser”:

Any equipment

or system used

in solvent

cleaning.

“Delivery Vessel”:

Any tank truck or trailer equipped

with a storage tank that

is used for the transport of

gasoline

to

a

stationary

storage tank

at

a

gasoline

dispensing facility, bulk gasoline plant or bulk gasoline

terminal.

“Distillate Fuel Oib”:

Fuel oils of grade No.

1 or 2 as

specified in detailed requirements for fuel oil A.S.T.M.

D—369—69

(1971).

“Dry

Cleaning Facility”:

A

facility

engaged

in

the

cleaning

of

fabrics

using

an

essentially

nonaqueous

solvent

by

means

of

one

or

more

solvent

washes,

extraction of excess solvent by spinning and drying by

tumbling in an airstream.

The facility includes, but is

not limited to, washers, dryers, filter and purification

systems, waste disposal systems, holding tanks, pumps and

attendant ‘piping and valves.

“Dump—Pit Area”:

Any area where grain is received at a

grain-handling or grain-drying operation.

“Effective Grate Area”:

That area of a dump—pit grate

through which air passes, or would pass, when aspirated.

“Effluent Water Separator”:

Any

tank, box, sump or other

apparatus

in which any organic material floating on or

entrained or contained in water entering such tank, box,

sump

or

other

apparatus.

is

physically

separated

and

removed from such water prior to outfall,

drainage or

recovery of such water.

“Emission Rate”:

Total quantity of any air contaminant’

lischarge into the atmosphere in any one—hour period.

“Enclose”: ,with respect to 35 Ill. Adm. Code 2l5.Subpart

r,

to cover any volatile organic liquid surface that is

exposed to the atmosphere.

130—406

---

13

“End Sealing Compound Coat”:

A compound applied to can

ends

which

functions

as

a

gasket

when

the

end

is

assembled on the can.

“Excess

Air”:

Air

supplied

in

addition

to

the

theoretical quantity necessary for complete combustion of

all fuel and/or combustible waste material.

“Excessive Release”:

A discharge of more than 295g (0.65

pounds)

of

mercaptans

or

hydrogen

sulfide

into,

the

atmosphere

in any five minute period.

“Existing

Grain-Drying

Operation”:

Any

grain-drying

operation the construction or modification of which was

commenced prior to June 30,

1975.

“Existing Grain-Handling Operation”:

Any grain-handling

operation the construction or modification of which was

commenced prior to June 30,

1975.

“Exterior Base Coat”:

An initial coating applied to the

exterior of a can after the can body has been formed.

“Exterior End Coat”:

A coating applied by rollers or

spraying to the exterior end of a can.

“External Floating Roof”:

A storage vessel cover in an

open top tank consisting of

a

double deck

or pontoon

single deck which

is supported by the petroleum liquid

being

contained

and

is

equipped with

a

closure

seal

between the deck edge and tank wall.

“Extreme

Performance

Coating”:

Coatings designed

for

exposure to any of the following:

the ambient weather

conditions,

temperatures

above

368.15° K

(203° F),

detergents,

abrasive

and

scouring

agents,

solvents,

corrosive

atmospheres,

or

other

similar

extreme

environmental conditions.

“Fabric

Coating”:

The coating of

a

textile substrate

including operations where the coating impregnates the

substrate.

“Final Repair Coat”:

The repainting of any coating’which

is damaged during vehicle assembly.

“Firebox”:

The chamber or compartment of

a boiler or

furnace

in

which

materials

are

burned,

but

not

the

combustion chamber or afterburner of an incinerator.

“Flexographic

Printing”:

The

application

of

words,

designs and pictures to

a substrate by means

of a roll

130—407

---

14

printing technique in which the pattern to be applied is

raised above the printing roll and the image carrier is

made of elastomeric materials.

“Floating Roof”:’ A roof on a stationary tank, reservoir

or other container which moves vertically upon change in

volume of the stored material.

“Freeboard Height”:

For open top vapor degreasers,

the

distance from the top of the vapor zone to the top of the

degreaser

tank.

For

cold

cleaning

degreasers,

the

distance from the solvent to the top of the degreaser

tank.

“Fuel Combustion Emission Source”:

Any furnace, boiler

or

similar equipment used

for the primary purpose

of

producing heat or power by indirect heat transfer.

“Fuel Gas System”:

A system for collection of refinery

fuel

gas

including,

but

not

limited

to,

piping

for

collecting tail gas from various process units,

mixing

drums and controls and distribution piping.

“Fugitive Particulate Matter”:

Any particulate matter

emitted into the atmosphere other than through a stack,

provided that nothing in this definition or in 35 Ill.

Adm.

Code 2l2.Subpart K

shall

exempt

any

source

from

compliance with other provisions of 35 Ill. Adm. Code 212

otherwise applicable merely because of the absence of a

stack.

“Gas Service”:

Means that the component contains process

fluid

that

is

in

the

gaseous

state

at

operating

conditions.

“Gasoline”:

Any petroleum distillate having a Reid vapor.

pressure of

4 pounds or greater.

“Gasoline Dispensing Facility”:

Any site where gasoline

is transferred from a stationary storage tank to a motor

vehicle gasoline tank used to provide fuel to the engine

of that motor vehicle.

“Grain”:

The whole kernel or seed of corn, wheat,

oats,

soybeans and any other cereal or oil seed plant; and the

normal fines, dust and foreign matter which results from

harvesting, handling or conditioning.

The grain shall be

unaltered by grinding or processing.

“Grain—Drying

Operation”:

Any

operation,

excluding

aeration,

by which moisture

is removed from grain and

130—408

---

15

which typically uses forced ventilation with the addition

of heat.

“Grain-Handling and Conditioning Operation”:

A

grain

storage

facility

and

its

associate

grain

transfer,

cleaning, drying, grinding and mixing operations.

“Grain—Handling Operation”:

Any operation where one or

more of the following grain-related processes (other than

grain-drying

operation,

portable

grain-handling

equipment,

one—turn storage space,

and excluding flour

mills

and

feed

mills)

are

performed:

receiving,

shipping, transferring,

storing, mixing or treating of

grain

or

other

processes

pursuant

to

normal

grain

operations.

“Green Tire Spraying”:

The spraying of green tires, both

inside and outside,

with release compounds which help

remove air from the tire during molding and prevent the

tire from sticking to the mold after curing.’

“Green Tires”:

Assembled tires before molding and curing

have occurred.

“Gross Heating Value”:

Amount of heat produced when a

unit quantity of fuel

is burned to carbon dioxide and

water vapor,

and the water vapor condensed as described

in A.S.T.M. D—2015—66, D—900—55, D—1826—64 and D—240—64.

“Heavy

Liquid”:

Liquid with a

true’ vapor pressure of

less than 0.3 kPa (0.04 psi) at 294.3°K (70°F) or 0.1

Reid Vapor Pressure as determined by A.S.T.M. ,method D—

323; or which when distilled requires

a temperature of

300° F

or

greater

to

recover

10

of

the

liquid

as

determined by A.S.T.M. method D-86.

“Heavy Metals”:

For the purposes of Section 9.4 of the

Act,

elemental,

ionic,

or combined forms

of

arsenic,

cadmium, mercury,

chromium, nickel and lead.

“Heavy, Off-Highway Vehicle Products”:

For the purposes

of Section 215.204(k), heavy off-highway vehicle products

shall include:

heavy construction, mining,

farming or

material handling equipment;

heavy industrial

engines;

diesel—electric

locomotives

and

associated

power

generation

equipment;

and

the

components

of

such

equipment or engines.

“Hot Well”:

The reservoir of a condensing unit receiving

the condensate from a barometric condenser.

130—409

---

16

“Housekeeping Practices”:

Those activities specifically

defined in the list ‘of housekeeping practices developed

by

the Joint

EPA

-

Industry Task Force

and included

herein under 35 Ill. Adm. Code 212.461.

“Incinerator”:

Combustion apparatus in which refuse

is

burned.

“Indirect Heat Transfer”:

Transfer of heat in such a way

that the source of heat does not come into direct contact

with process materials.

“In—Process

Tank”:

A

container

used

for

mixing,

blending,

heating,

reacting,

holding,

crystallizing,

evaporating, or cleaning operations in the manufacture of

pharmaceuticals.

“In—situ Sampling Systems”:

Nonextractive samplers or

in—line samplers.

“Interior Body Spray Coat”:

A coating applied by spray

to the

interior of a can after the can body has been

formed.

“Internal

Transferring

Area”:

Areas

and

associated

equipment used for

conveying grain

among

the various

grain operations.

“Large Appliance Coating”:

The application of a coating

material to the component metal parts (including but not

limited

to

doors,

cases,

lids,

panels

and

interior

support parts)

of residential

and commercial

washers,

dryers,

ranges, refrigerators, freezers, water heaters,

dishwashers, trash compactors, air conditioners and other

similar products.

“Light—Duty Truck”:

Any second division motor vehicle,

as that term

is defined in the Illinois Vehicle Code,

(Ill.

Rev.

Stat.

1989,

ch.

95½,

pars.

1—100

et

seq.)

weighing less than 3854 kilograms (8500 pounds)

gross.

“Liquid-Mounted

Seal”:

A

primary

seal

mounted

in

continuous contact with the liquid between the tank wall

and the floating roof edge around the circumference of

the roof.

“Liquid Service”: Means that the equipment or component

contains process

fluid

that

is

in

a

liquid

state

at

operating conditions.

“Liquids

Dripping”:

Any

visible leaki~igfrom

a

seal

including spraying, misting, clouding and ice formation.

130—410

---

17

“Load—Out Area”:

Any area where grain

is transferred

from the grain-handling operation

to any vehicle

for

shipment or delivery.

“Low Solvent

Coating”:

A coating which contains

less

organic solvent than the conventional coatings used by

the industry.

Low solvent coatings include water-borne,

higher solids, electro-deposition and powder coatings.

“Magnet Wire Coating”:

The application of a coating of

electrically insulating varnish or enamel to conducting

wire’ to be used in electrical machinery.

-“Major Dump Pit”:

Any dump pit with an annual

grain

through-put

of

more

than

300,000

bushels,

or

which

receives more than 40

of the annual grain through-put of

the grain-handling operation.

“Major Metropolitan Area (MMA)”:

Any county or group of

counties which is defined by the following Table:’

MAJOR METROPOLITAN AREAS

IN ILLINOIS

(MMA’s)

MMA

COUNTIES INCLUDED IN NMA

Champaign-Urbana

Champaign

Chicago

Cook, Lake,’Will,

DuPage,

McHenry,

Kane,

Grundy,

Kendall, Kankakee

Decatur

Macon

Peoria

Peoria, Tazewell

Rockford

.

Winnebago

Rock Island

——

Moline

Rock Island

Springfield

Sangamon

St. Louis

(Illinois)

St.

Clair, Madison

Bloomington

-—

Normal

McLean

“Major Population Area (MPA)”:

Areas of major population

concentration in Illinois,

as described below:

The area within the counties of Cook; Lake; DuPage;

Will;

the townships of Burton,

Richmond, McHenry,

Greenwood, Nunda,

Door, Algonquin,

Grafton and the

municipality of Woodstock,

plus

a

zone extending

two miles beyond the boundary of said municipality

located in McHenry County; the townships of Dundee,

Rutland,

Elgin,

Plano,

St.

Charles,

Campton,

Geneva, Blackberry, Batavia, Sugar Creek and Aurora

located in Kane County; and the municipalities of

Kankakee,

Bradley

and

Bourbonnais,

plus

a

zone

extending two miles beyond the boundaries

of said

municipalities in Kankakee County.

13

0—4 11

---

18

The area within the municipalities of Rockford and

Loves

Park, plus a zone extending two miles beyond

the boundaries of said municipalities.

The area within the municipalities of Rock Island,

Moline,

East

Moline,

Carbon

Cliff,’

Milan,

Oak

Grove,

Silvis, Hampton, Greenwood and Coal Valley,

plus

a

zone

extending

two

miles

beyond

the

boundaries of said municipalities.

The area within the municipalities of Galesburg and

East

Galesburg,

plus

a

zone

extending two miles

beyond the boundaries of said municipalities.

The area within the municipalities of Bartonville,

Peoria and Peoria Heights,

plus

a

zone extending

two

miles

beyond

the

boundaries

of

said

municipalities.

The area within the municipalities of Pekin,

North

Pekin,

Marquette

Heights,

Creve

Coeur

and

East

Peoria, plus a zone extending two miles beyond the

boundaries of said municipalities.

The area within the municipalities of Bloomington

and Normal, plus a zone extending two miles beyond

the boundaries of said municipalities.

The area within the municipalities

of

Champaign,

Urbana and Savoy,

plus a zone extending two miles

beyond the boundaries of said municipalities.

The area within the municipalities of Decatur, Mt.

Zion, Harristown and Forsyth, plus a zone extending

two

miles

beyond

the

boundaries

of

said

municipalities.

The area within the municipalities of Springfield,

Leland

Grove,

Jerome,

Southern

View,

Grandview,

Sherman

and

Chatham,

plus

a

zone

extending

two

miles beyond the boundaries of said municipalities.

The area within the townships of Godfrey,

Foster,

Wood River,

Fort Russell,

Chouteau,

Edwardsville,

Venice,

Nameoki,

Alton,

Granite

City

and

Collinsville

located

in Madison

County;

and the

townships

of

Stites,

Canteen,

Centrevible,

Caseyville,

St.

Clair,

Sugar

Loaf

and

Stookey

located in St. Clair County.

“Manufacturing Process”:

A process emission source or

series of process emission sources used to convert raw

130—412

---

19

materials, feed stocks, subasseinblies or other components

into a product, either for sale or for use as a component

in

a subsequent manufacturing process.

“Marine

Terminal”:

A

facility

primarily

engaged

in

loading

and

unloading waterc~raft.

“Metal Furniture Coating”:

The application of a coating

material to any furniture

piece made

of metal

or

any

metal

part which

is

or

will., be

assembled with

other

metal,

wood,

fabric,

plastic or glass parts to form

a

furniture piece including,

but not limited to,

tables,

chairs,

wastebaskets,

beds,

desks,

lockers,

benches,

shelving,

file cabinets, lamps and room dividers.

This

definition shall not apply to any coating line coating

metal

parts

or products

that

is

identified under

the

Standard Industrial Classification Code for Major Groups

33,

34,

35,

36,

37,

38,

39,

40 or 4b.

“Miscellaneous

Fabricated

Product

Manufacturing

Process”:

A

manufacturing

process

involving

one

or

more

of

the

following applications,

including

any drying

and curing of formulations, and capable of emitting

volatile organic material:

Adhesives

to fabricate

or assemble non—furniture

components or products

Asphalt solutions to paper or fiberboard

Asphalt to paper or felt

Coatings or dye to leather

Coatings to plastic

Coatings to rubber or glass

Curing

of

furniture

adhesives

in

an

oven

which

would emit in excess of 10 tons of volatile o.rganic

material

per

year

if

no

air

pollution

control

equipment

were

used

Disinfectant material to manufactured items

Plastic foam scrap or “fluff” from the manufacture

of foam containers and packaging material to form

resin pellets

Resin solutions to fiber substances

130—4 13

---

20

Rubber solutions to molds

Viscose solutions for food casings

The storage ‘and handling of formulations associated

with the process described above.

The use and handling of organic

liquids

and

other

substances for clean—up operations associated with

the process described above.

“Miscellaneous Formulation Manufacturing Process”:

A manufacturing process which compounds one or more

of

the

following

and

is

capable

of

emitting

volatile organic material:

Adhesives

Asphalt

solutions

Caulks,

sealants or waterproofing agents

Coatings,

other

than

paint and ink

Concrete

curing

compounds

Dyes

Friction

materials

and

compounds

Resin solutions

Rubber

solutions

Viscose

solutions

The

storage

and

handling

of

formulations

associated

with

the

process

described

above.

The

use

and

handling

of

organic

liquids

and

other

substances for clean—up operations associated with

the process described -above.

“Miscellaneous

Metal

Parts

and

Products”:

For

the

purpose of 35 Ill. Adm. Code 215.204, miscellaneous metal

parts and products shall include farm machinery,

garden

machinery,

small

appliances,

commercial

machinery,

industrial machinery, fabricated metal products and any

other

industrial

category which

coats

metal

parts

or

products

under the Standard

Industrial

Classification

Code for Major Groups 33,

34,

35,

36,

37,

38 or 39 with

130—414

---

21

the exception of the following:

coating lines subject to

35

Ill.

Adm.

Code

.

215.204(a)

through

(i)

and

(k),

automobile or light-duty truck refinishing, the exterior

of

marine

vessels

and

the

customized

top

coating

of

automobiles-and trucks if production is less than thirty-

five vehicles per day.

“Miscellaneous Organic Chemical Manufacturing Process”:

A manufacturing process which produces by chemical

reaction,

one

or more

of

the

following

organic

compounds

or mixtures

of

organic

compounds

and

which

is

capable

of

emitting

volatile

organic

materials:

Chemicals listed

in

35

Ill.

Adin.

Code

215.

Appendix D.

Chlorinated and sulfonated compounds

Cosmetic,

detergent,

soap

or

surfactant

intermediaries Or specialties and products

Disinfectants

Food additives

Oil

and

petroleum

product additives

Plasticizers

Resins

or

polymers

Rubber additives

Sweeteners

Varnishes

The

storage

and

handling

of

formulations

associated

with the process described above.

The use and handling of organic liquids and other

substances for clean-up operations associated with

the process described above.

“Mixing Operation”:

The operation of combining two or

more ingredients, of which at least one is a grain.

“New Grain-Drying Operation”:

Any

grain-drying operation

the construction or modification of which is commenced on

or after June 30,

1975.

130—4 15

---

22

“New

Grain-Handling

Operation”:

Any

grain-handling

operation the construction of modification of which

is

commenced on or after June 30, 1975.

“No Detectable Volatile Organic Material Emissions”:

A

discharge

of

volatile

organic

material

into

the

atmosphere as indicated by an instrument reading of less

than 500 ppm above background as determined in accordance

with

40

CFR 60.485(c).

“One

Hundred

Percent

Acid”:

Acid

with

a

specific

gravity

of

1.8205

at 30° C

in

the

case

of

sulfuric

acid

and

1.4952

at

30°

C

in

the

case

of

nitric

acid.

“One—Turn

Storage

Space”:

That

space

used

to

store

grain

with

a

total

annual

through—put

not

in

excess

of

the

total

bushel

storage

of

that

space.

“Opacity”:

A condition which renders material partially

or wholly impervious to transmittance of light and causes

obstruction of an observer’s view.

For the purposes of

these

regulations,

the

following

equivalence

between

opacity and Ringelmann shall be employed:

Opacity

Percent

Ringelmann

10

0.5

20

1.

30

1.5

40

2.

60

3.

80

‘

4.

100

5.

“Open

Top

Vapor

Degreasing”:

The

batch

process

of

cleaning

and

removing

soils

from surfaces by condensing

Liot

solvent

vapor

on

the

colder

metal

parts.

“Operator of Gasoline Dispensing Facility”:

Any person

who is the lessee of or operates, controls or supervises

~ gasoline dispensing facility.

“Organic Compound”:

Any

compound of carbon, ‘excluding

~arbon monoxide,

carbon dioxide,

carbonic

acid,

metal

;arbides or carbonates,

and ammonium carbonate.

“Organic

Material”:

Any

chemical

compound of

carbon

including

diluents and thinners

which

are liquids

at

3tandard conditions and which are used as dissolvers,

iiscosity

reducers

or cleaning agents,

but

excluding

aethane, carbon monoxide, carbon dioxide, carbonic acid,

netallic

carbonic

acid,

metallic

carbide,

metallic

;arbonates and ainmonium carbonate.

130—4 16

---

23

“Organic

Materials”:

For

the

purposes

of

Section

9.4

of

the

Act,

any

chemical

compound

of,

carbon

including

diluents

and

thinners

which

are

liquids

at, standard

conditions

and

which

are

used

as dissolvers, viscosity

reducers or cleaning agents, and polychborinated dibenzo—

p—dioxins, polychborinated dibenzofurans and polynuclear

aromatic

hydrocarbons

are

organic

materials,

while

methane, carbon monoxide, carbon dioxide, carbonic acid,

metallic

carbonic

acid,

metallic

carbide,

metallic

carbonates and ammoniun carbonate are organic materials.

“Organic Vapor”:

Gaseous phase of an organic material or

a mixture of

organic

materials present in the atmosphere.

“Overvarnish”:

A coating applied directly over ink or

printing.

“Owner of Gasoline Dispensing Facility”:

Any person who

has legal or equitable title to a stationary storage tank

at a gasoline dispensing facility.

-

“Packaging Rotogravure Printing”:

Rotogravure printing

upon

paper,

paper

board,

metal

foil,

plastic

film

and

other

substrates,

which

are,

in

subsequent operations,

formed

into packaging products or labels for articles to

be

sold.

“Paint Manufacturing Plant”:

A plant that mixes, blends,

or

compounds

enamels,

lacquers,

sealers,

sheblacs,

stains, varnishes or pigmented surface coatings.

“Paper

Coating”:

The application of a coating material

to

paper

or

pressure

sensitive

tapes,

regardless

of

substrate,

including web coating on plastic

fibers and

decorative coatings on metal foil.

“Particulate Matter”:

Any solid

or

liquid

material,

other than water, which exists in finely divided form.

“Petroleum

Liquid”:

Crude

oil,

condensate

or

any

finished

or

intermediate

product

manufactured

at

a

petroleum refinery, but not including Number

2

through

Number 6 fuel oils as specified in A.S.T.M. D—396—69, gas

turbine fuel oils Numbers 2-GT through 4-GT as specified

in A.S.T.M. D—2880—71 or diesel fuel oils Numbers 2-D and

4—D,

as specified in A.S.T.M. D—975—68.

“Petroleum Refinery”:

Any facility engaged in producing

gasoline,

kerosene,

distillate fuel oils, residual fuel

oils, lubricants, or other products through distillation,

cracking, extraction or reforming of unfinished petroleum

derivatives.

130—4 17

---

24

“Pharmaceutical”:

Any

compound

or

mixture,

other

than

food,

used

in

the

prevention,

diagnosis,

alleviation,

treatment

or

cure

of

disease

in

man

and

animal.

“Pharmaceutical

Coating

Operation”:

a

device

in

which

a

coating

is applied to

a pharmaceutical,

including any

drying

or

curing

of

the

coating.

“Photochemically

Reactive

Material”:

Any

organic

material with an aggregate of more than 20 percent of its

total

volume

composed

of

the

chemical

compounds

classified below or the composition of which exceeds any

of

the

following

individual

percentage

composition

limitations.

Whenever

any

photochemically

reactive

material or any constituent of any organic material may

be classified from its chemical structure into more than

one

of

the

above

groups

of organic materials it

shall

be

considered as a member of the most reactive group,

that

is, the group having the least allowable percent of the

total organic materials.

A combination of hydrocarbons, alcohols, aldehydes,

esters,

ethers

or ketones

having

an ‘olefinic or

cyclo—olefinic types of unsaturation:

5 .percent.

This definition does not apply to perchiorethylene

or trichboroethylene.

A combination of aromatic compounds with eight or

more carbon

atoms

to the molecule except

ethyl—

benzene:

8 percent.

A

combination

of

ethylbenzene,

ketones

having

branched hydrocarbon

structures

or

toluene:

20

percent.

“Plant”:

all of the pollutant—emitting activities which

belong to the same industrial grouping,

are located on

one or more contiguous or adjacent properties,

and are

under the control of the same person

(or persons under

common

control),

except

the ‘activities

of

any marine

vessel.

Pollutant—emitting

activities

shall.

be

considered as part of the same industrial grouping if

they belong to the same major group (i.e., which have the

same

two-digit

code)

as

described

in

the

“Standard

Industrial Classification Manual”,

1987.

“PM—lU”:

particulate matter with an aerodynamic diameter

less

than

or

equal

to

a

nominal

10

micrometers,

as

measured

by the applicable

test methods

specified ~y

rulein

35

Ill.

Adm.

Code

212.110.

Ambient

air

concentrations

for

PM—b

are

usually

expressed

in

micrograms per cubic meter

(ug/m3).

130—418

---

25

“Pneumatic

Rubber

Tire

Manufacture”:

The

production

of

pneumatic rubber tires with a bead diameter up to but not

including

20.0

inches

and

cross section dimension up to

12.8

inches,

but

not

including

specialty

tires

for

antique or

other vehicles

when produced

on

equipment

separate from normal production lines for passenger or

truck type tires.

“Polybasic Organic Acid Partial Oxidation Manufacturing

Process”:

Any process

involving partial oxidation of

hydrocarbons with air to manufacture polybasic acids or

their

anhydrides,

such

as

maleic

anhydride,

phthalic

anhydride,

terephthalic

acid,

isophthalic

acid,

trimelletic anhydride.

“Portable

Grain-Handling

Equipment”:

Any

equipment

(excluding portable grain

dryers)

that

is

designed

and

maintained to be movable primarily

for use

in

a

non—

continuous operation for loading and unloading one—turn

storage space,

and

is not physically connected to the

grain elevator,

provided that the manufacturer’s rated

capacity of the equipment does not exceed 10,000 bushels

per hour.

“Portland

Cement

Manufacturing

Process

Emission

Source”:

any

items

of

process

equipment

or

manufacturing

processes

used

in

or

associated with the production

of portland

cement,

including,

but not limited to,

a kiln,

clinker

cooler, raw mill system, finish mill system, raw material

dryer, material storage bin or system, material conveyor

belt or

other

transfer system,

material

conveyor belt

transfer

point,

bagging

operation,

bulk

unloading

station, or bulk loading station.

“Portland

Cement

Process”

or

“Portland

Cement

Manufacturing

Plant”:

Any

facility

or

plant

manufacturing

portland

cement

by

either

the

wet

or

dry

process.

“Power

Driven

Fastener

Coating”:

The

coating

of

nail,

staple,

brad

and

finish

nail

fasteners

where

such

fasteners are

fabricated

from

wire

or

rod

of 0.0254 inch

diameter or greater, where such fasteners are bonded into

coils

or

strips,

such coils

and strips

containing

a

number of such fasteners,

which fasteners are manufac-

tured for use in power tools, and which fasteners must

conform with formal

standards for specific uses estab-

lished

by various

federal

and

national

organizations

including Federal Specification FF-N-lOSb of the General

Services Administration dated August 23,

1977

(does

not,

include

any

later

amendments

or

editions;

U.S.

Army

Armament Research and Development Command, Attn:

DRDAR—

130—4 19

---

26

TST,

Rock

Island,

IL

61201),

Bulletin

UM—25d

of

the

U.S.’

Department

of

Housing

and

Urban

Development

-.

Federal

Housing

Administration

dated

September

5,

1973

(does

not

include

any

later

amendments

or

editions;

Department

of

HUD,

547

W.

Jackson

Blvd.,

Room

1005,

Chicago,

IL

60606),

and

the

Model

Building

Code

of

the

Council

of

American

Building

Officials,

and

similar

standards.

For

the

purposes

of

this

definition,

the

terms

“brad”

and

“finish

nail”

refer

to

single

leg fasteners fabricated in the

same

manner

as

staples.

The

application

of

coatings

to

staple,

brad,

and

finish

nail

fasteners

may

be

associated

with

the

incremental

forming

of

such

fasteners

in

a

cyclic or repetitious manner (incremental fabrication) or

with

the

forming

of

strips

of

such

fasteners

as

a

unit

from

a

band

of

wires

(unit

fabrication).

“PPM

(Vol)

-

(Parts

per

Million)

(Volume)”:

A

volume/volume

ratio

which

expresses

the

volumetric

concentration

of

gaseous

air

contaminant

in

a

million

unit

volumes

of

gas.

“Pressure Release”:

The emission of materials resulting

from system pressure being greater than set pressure of

the pressure relief device.

“Pressure

Tank”:

A

tank

in which fluids are stored at a

pressure

greater

than

atmospheric

pressure.

“Prime

Coat”:

The first

film

of

coating

material

applied

in

a

multiple

coat

operation.

“Prime

Surfacer

Coat”:

A

film

of

coating

material

that

touches

up

areas

on

the

surface

not

adequately

covered

by

the

prime

coat

before application of the top coat.

“Process”:

Any

stationary

emission

source

other

than

a

fuel

combustion

emission

source

or

an

incinerator.

“Process

Unit”:

Components

assembled

to

produce,

as

intermediate

or

final

products,

one

or more

of

the

chemicals listed in 35 Ill. Adm. Code 215.Appendix D.

A

process unit can operate independently if supplied with

sufficient feed or raw materials and sufficient storage

facilities for the product.

“Process Unit Shutdown”:

A work practice or operational

procedure that stops production from a process unit or

part of a process unit.

An unscheduled work practice or

operational

procedure

that

stops

production

from

a

process unit or part of a process unit for less than 24

hours is not a process unit shutdown.

The use of spare

components

and

technically

feasible

bypassing

of

130—420

---

27

components without stopping production is not a process

unit shutdown.

“Process Weight Rate”:

The actual weight or engineering

approximation thereof of all materials except liquid and

gaseous

fuels and combustion

air,

introduced

into any

process per hour.

For a cyclical or batch operation, the

process weight rate shall be determined by dividing such

actual weight or engineering approximation thereof by the

number of hours of operation excluding any time,during

which the equipment is idle.

For continuous processes,

the process weight rate shall be determined by dividing

such actual weight or engineering approximation thereof

by

the

number

of

hours

in

one

complete

operation,

excluding

any

time

during

which

the

equipment

is

idle.

“Production Equipment

Exhaust

System”:

A

system

for

collecting and directing into the atmosphere emissions of

volatile organic material from reactors, centrifuges and

other process emission sources.

“Publication

Rotogravure

Printing”:

Rotogravure

printing

upon

paper

which

is

subsequently

formed

into

books,

magazines,

catalogues,

brochures,

directories, newspaper

supplements

or

other

types

of’ non—packaging

printed

materials.

“Purged Process Fluid”:

Liquid or vapor from a process

unit

that

contains volatile organic material and

that

results from flushing or cleaning the sample line(s)

of

a

process

unit

so

that

an uncontaminated sample may then

be

taken

for

testing

or

analysis.

“Reactor”:

A

vat,

vessel

or

other

device

in

which

chemical reactions take place.

“Reasonably Available Control Technology

(PACT)”:

The

lowest emission limitation that

an emission source

is

capable

of

meeting

by

the

application

of

control

technology

that

is

reasonably

available

considering

technological and economic feasibility.

“Refinery Fuel

Gas”:

Any

gas which is generated by a

petroleum refinery process unit and which is coñbusted

at

the refinery,

including any gaseous mixture of natural

gas and fuel gas.

“Refinery

Unit,

Process

Unit

or

Unit”:

A

set

of

components which area part of a basic process operation

such

as

distillation,

hydrotreating,

cracking

or

reforming of hydrocarbons.

130—42 1

---

28

“Refrigerated Condenser”:

a surface condenser in which

the coolant supplied to the condenser has been cooled by

a mechanical device,

other than by

a cooling tower

or

evaporative spray cooling,

such as a refrigeration unit

or steam chiller unit.

“Residual Fuel Oil”:

Fuel oils ‘of grade No.

4,

5 and

6

as

specified

in

detailed

requirements

for

fuel

oils

A.S.T.M. D—396—69

(1971).

“Restricted Area”:

The area within the boundaries of any

“municipality” as defined in the Illinois Municipal Code

(ch. 24, par.

1—1—1 et seq.), plus a zone extending one

mile

beyond

the

boundaries

of

any

such

municipality

having

a

population

of

1000

or

more

according

to

the

latest

federal

census.

“Ringelmann Chart”:

The chart published and described in

the

Bureau

of

Mines,

U.S.

Department

of

Interior,

Information Circular 8333 ‘(Revision of IC7718)

May

1,

1967,

or any adaptation thereof which has been approved

by the Agency.

“Roadway”:

Any

street,

highway,

road,

alley,

sidewalk,

parking

lot,

airport,

rail

bed

or

terminal,

bikeway,

pedestrian

mall

or

other

‘

structure

used

for

transportation purposes.

“Roll

Printing”:

The

application

of

words,

designs

and

pictures

to

a

substrate

usually

by

means

of

a

series

of

hard

rubber

or

metal

rolls

each

with

only

partial

coverage.

“Rotogravure

Printing”:

The

application

of

words,

designs

and

pictures to a substrate by means of a roll

printing

technique

in

which

the

pattern

to

be

applied

is

recessed relative to the non—image area.

“Safety Relief Valve”:

A valve which is normally closed

and

which

is

designed

to

open

in

order

to

relieve

excessive pressures within a vessel or pipe.

“Sandblasting”:

The use of a mixture of sand and air at

high pressures

for cleaning or polishing

any type

of

surface.

“Sensor”:

A device that measures a physical quantity or

the

change

in

a

physical quantity such as temperature,

pressure,

flow

rate,

pH,

or

liquid

level.

130—422

---

29

“Set

of

Safety

Relief

Valves”:

One

or

more

safety

relief

valves

designed

to

open

in

order

to

relieve

excessive

pressures

in

the

same

vessel

or

pipe.

“Screening”:

Separating material according to size by

pressing undersized material through one or more mesh

surfaces

(screens)

in

series,

and retaining oversized

material on the mesh surfaces

(screens).

“Sheet Basecoat”:

A coating applied to metal when the

metal is in sheet form to serve as either the exterior or

interior of

a can

for either two—piece or three—piece

cans.

“Shotblasting”:

The use of a mixture of any metallic or

non-metallic

substance

and air

at high

pressures

for

cleaning

or

polishing

any

type

of

surface.

“Side-Seam

Spray

Coat”:

A coating

applied

to

the

seam

of

a three—piece can.

“Smoke”:

Small

gas—borne

particles

resulting

from

incomplete

combustion,

consisting predominately but not

exclusively

of

carbon,

ash

and

other

combustible

material,

that

form

a

visible

plume

in

the

air.

“Smokeless

Flare”:

A

combustion

unit

and

the

stack

to

which it

is affixed

in

which

organic material achieves

combustion by burning in the atmosphere such that the

smoke

or

other

particulate

matter

emitted

to

the

atmosphere

from

such

combustion

does

not

have

an

appearance density or

shade darker

that No.

1

of the

Ringbemann

Chart.

“Solvent

Cleaning”:

The

process

of

cleaning

soils

from

surfaces

by

cold cleaning, open top vapor degreasing or

conveyori

zed

degreas ing.

“Specialty High Gloss

Catalyzed Coating”:

Commercial

contract finishing of material prepared for printers and

lithographers where the finishing process uses a solvent-

borne coating, formulated with a catalyst,

in a quantity

of no more than 12,000 gallons/year as supplied, where

the coating machines are sheet fed and the coated sheets

are brought to a minimum surface temperature of 190°F,

and where the coated sheets

are to achieve the minimum

specular reflectance index of 65 measured at a 60 degree

angle

with

a

gloss

meter.

“Splash Loading”:

A method of loading a tank,

railroad

tank car, tank truck or trailer by use of other than a

submerged loading pipe.

130—423

---

30

“Stack”:

A

flue

or

conduit,

free—standing

or

with

exhaust

port

above

the

roof

of

the

building

on

which

it

is

mounted,

by

which

air contaminants are emitted into

the atmosphere.

“Standard Conditions”:

A temperature

of’ 70°

F

and

a

pressure of 14.7 pounds per square inch absolute (psia).

“Standard Cubic

Foot

(scf)”:

The volume

of

one cubic

foot of gas at standard conditions.

“Startup”:

The setting

in

operation of

an emission

source for any purpose.

“Stationary

Emission

Source”:

An

emission source which

is

not self-propelled.

“Stationary Storage Tank”:

Any container of liquid or

gas which is designed and constructed to remain at one

site.

“Submerged Loading Pipe”:

Any loading pipe the discharge

opening of which is entirely submerged when the liquid

level

is

6

inches

above the bottom of the tank.

When

applied to

a

tank which

is

loaded from the

side,

any

loading pipe the discharge of which is entirely submerged

when the

liquid

bevel

is

18

inches

or two

times

the

loading pipe diameter, whichever is greater,

above the

bottom of the tank.

The definition shall also apply to

any loading pipe which is continuously submerged during

loading operations.

“Sulfuric

Acid

Mist”:

Sulfuric

acid

mist

as

measured

according to the method specified in

35 Ill. Adm. Code

214.101(b).

“Surface

Condenser”:

A

device

which removes a substance

from

a

gas

stream

by

reducing

the

temperature

of

the

stream, without direct contact between the coolant and

the

stream.

“Synthetic

Organic

Chemical

or

Polymer

Manufacturing

Plant”:

A plant that produces, as intermediates or final

products,

one

or

more

of

the

chemicals

or

polymers

listed

in 35

Ill.

Adm.

Code 215.Appendix

D.

“Tablet Coating Operation”:

A pharmaceutical

coating

operation in which tablets are coated.

“Top Coat”:

A

film of coating material applied

in

a

multiple coat operation other than the prime coat, final

repair

coat

or

prime

surfacer

coat.

130—424

---

31

“Transfer Efficiency”:

ratio

of

the amount of coating

solids deposited onto a

part or product to the total

amount of coating solids used.

“Tread End Cementing”:

The application of

a

solvent—

based cement to the tire tread ends.

“True

Vapor

Pressure”:

The equilibrium partial pressure

exerted

by

a

petroleum

liquid

as

determined

in

accordance

with methods described in American Petroleum Institute

Bulletin

2517,

“Evaporation

Loss

From

Floating

Roof

Tanks”

(1962).

“Turnaround”:

The

procedure

of

shutting

down

an

operating

refinery

unit,

emptying

gaseous and

liquid

contents to do inspection, maintenance and repair work,

and putting the unit back into production.

“Undertread Cementing”:

The application of

a solvent—

based cement to the underside of a tire tread.

“Unregulated Safety Relief Valve”:

A safety relief valve

which

cannot be

actuated by

a

means

other

than high

pressure in the pipe or vessel which it protects.

“Vacuum

Producing System”:

Any reciprocating, rotary or

centrifugal blower or compressor,

or any jet ejector or

device

that

creates

suction

from

a

pressure

below

atmospheric and discharges against a greater pressure.

“Valves Not Externally Regulated”:

Valves that have no

external controls,

such as in—line check valves.

“Vapor

Balance

System”:

Any combination

of

pipes

or

hoses

which creates

a closed system between the vapor

spaces of an unloading tank and

a

receiving tank such

that

vapors

displaced

from

the

receiving

tank

are

transferred to the tank being unloaded.

“Vapor

Collection

System”:

All

piping,

seals,

hoses,

connections, pressure-vacuum vents,

and other possible

sources

between the gasoline

delivery vessel

and the

vapor processing

unit or the

storage tanks

and vapor

holder.

.

“Vapor Control System”:

Any system that prevents release

to

the

atmosphere

of

organic

material

in

the

vapors

displaced

from

a

tank

during

the

transfer

of

gasoline.

“Vapor—Mounted

Primary

Seal”:

A

primary seal

mounted,

with

an

air

space

bounded

by

the

bottom

of

the

primary

130—425

---

32

seal,

the tank wall, the liquid surface and the floating

roof.

“Vinyl

Coating”:

.

The

application

of

a

topcoat

or

printing

to

vinyl

coated

fabric

or

vinyl

sheets;

provided, however, that the application of an organosol

or plastisol is not vinyl coating.

“Volatile Organic Liquid”:

Any liquid which

contains

volatile organic material.

“Volatile Organic Material”:

Any

organic

compound

which

participates

in

atmospheric

photochemical

reactions

unless

specifically

exempted

from

this

definition.

Volatile

organic

material

emissions

shall

be

measured by the reference methods specified under

40

CFR

60,

Appendix A

(1986)

(no future amendments

or

editions

are

included),

or,

if

no

reference

method

is

applicable,

may

be

determined

by

mass

balance calculations.

For purposes of this definition, the following are

not volatile organic materials:

Chborodifluoroethane (HCFC-l42b)

Chborodifluoromethane

(CFC-22)

Chboropentafluoroethane

(CFC-ll5)

2—Chloro-b, 1,1,

2,—tetrafluoroethane

(HCFC-124)

Dichborodifluoromethane

(CFC-l2)

Dichborofluoroethane (HCFC-l4lb)

Dichboromethane

(Methylene chloride)

Dichlorotetrafluoroethane

(CFC-ll4)

Dichborotrifluoroethane (HCFC-l23)

1, 1—Difluoroethane (HFC-l52a)

Ethane

Methane

Pentafluoroethane

(HFC-125)

Tetrafluoroethane (HFC-l34a)

1,1,2, 2—Tetrafluoroethane (HFC-134)

Trichloroethane

(Methyl chloroform)

Trichlorofluoromethane

(CFC-1l)

Trichlorotrifluoroethane (CFC-ll3)

1,1,1—Trifluoroethane (HFC-l43a)

Trifluoromethane

(FC-23)

and the following classes of compounds:

Cyclic,

branched,

or

linear, completely

fluorinated alkanes.

130—426

---

33

Cyclic,

branched,

or linear, completely

fluorinated ethers with no unsaturations.

Cyclic,

branched,

or

linear, completely

fluorinated

tertiary

amines

with

no

unsaturations.

Sulphur—containing perfluorocarbons with

no unsaturations

and with sulfur

bonds

only to carbon and fluorine.

BOARD

NOTE:

USEPA

or

the

Agency

may

require

monitoring

to

demonstrate

the

amount

of

an

exempted

compound

in

a

source’s

emissions

on

a

case—by—case

basis as a pre—condition to exemption of

that

compound

under

certain

circumstances, ‘such

as

where

VOMs

and

exempted compounds

are

mixed

together,

there

are

a

large

number

of

exempted

compounds, or the chemical composition of

the exempted compounds is not known.

See

35

Ill.

Adm.

Code

215.108;

56

Fed.Reg.

11419—20.

“Volatile

Organic

Material

Content”

or

“VOMC”:

the

emissions of volatile organic material which would result

from the exposure of

a coating, printing ink,

fountain

solution, tire spray, dry cleaning waste, or other similar

material to the air, including any drying or curing,

in

the absence of any control equipment.

VOMC is typically

expressed as kilogram

(kg) VON/liter (lb VON/gallon)

of

coating or coating solids,

or kg VOM/kg

(lb VOM/ib)

of

coating solids,

of coating material or material.

“Volatile

Petroleum

Liquid”:

Any

petroleum

liquid

with

a true vapor pressure that is greater than 1.5 psia

(78

millimeters of mercury)

at standard conditions.

“Wastewater (Oil/Water) Separator”:

Any device or piece

of equipment which utilizes the difference

in density

between

oil

and

water

to

remove

oil

and ‘associated

chemicals of water, or any device, such as a flocculation

tank or

a

clarifier,

which

removes petroleum derived

compounds from waste water.

“Weak

Nitric

Acid Manufacturing

Process”:

Any

acid

producing

facility

manufacturing

nitric

acid

with

a

concentration of bess than 70 percent by weight.

130—427

---

34

“Woodworking”:

The shaping, sawing, grinding, smoothing,

polishing and making into products of any form or shape

of wood.

(Source:

Amended at 16 Ill. Reg.

effective

TITLE

35:

ENVIRONMENTAL PROTECTION

SUBTITLE B:

AIR POLLUTION

CHAPTER

I:

POLLUTION CONTROL BOARD

SUBCHAPTER

C:

EMISSION

STANDARDS

AND

LIMITATIONS FOR STATIONARY SOURCES

PART 212

VISIBLE

AND

PARTICULATE.

MATTER

EMISSIONS

SUBPART

A:

GENERAL

Section

212.100

212.107

212.108

212.

109

212.110

212.111

212.112

212.113

Scope and Organization

Measurement Method for Visible Emissions

Measurement

Methods

for PM—lU Emissions

Measurement Methods

for

Opacity

Measurement Methods For Particulate Matter

Abbreviations and Units

Definitions

Incorporations

by

Reference

SUBPART

B:

VISIBLE

EMISSIONS

Opacity

Standards

Limitations for Certain New Sources

Limitations for All Other Sources

Exceptions

Determination of Violations

Adjusted

Opacity

Standards

Procedures

SUBPART D:

PARTICULATE MATTER EMISSIONS FROM INCINERATORS

Limitations for Incinerators

Aqueous

Waste

Incinerators

Certain Wood Waste Incinerators’

Explosive

Waste

Incinerators

Continuous

Automatic

Stoking

Animal

Pathological

Waste

Incinerators

SUBPART

E:

PARTICULATE MATTER

EMISSIONS

FROM

FUEL COMBUSTION EMISSION SOURCES

Section

212.121

212.122

212.123

212.124

212.125

212.126

Section

212.181

212.182

212.

183

212

.

184

212.185

130—428

---

35

Section

212.201

Existing

Sources

Using

Solid

Fuel

Exclusively

Located

in

the

Chicago

Area

212.202

Existing

Sources

Using

Solid Fuel Exclusively Located

Outside

the

Chicago

Area

212.203

Existing

Controlled

Sources

Using

Solid

Fuel

Exclusively

212.204

New

Sources

Using

Solid

Fuel

Exclusively

212.205

Existing

Coal-fired

Industrial

Boilers

Equipped

with

Flue

Gas

Desulfurization

Systems

212.206

Sources

Using

Liquid

Fuel

Exclusively

212.207

Sources

Using

More

Than

One

Type

of

Fuel

212.208

Aggregation

of

Existing

Sources

212.209

Village

of

Winnetka

Generating

Station

212.210

Emissions

Limitations

For

Certain

Fuel

Combustion

Emission

Sources

Located

in

the

Vicinity

of

Granite

City

SUBPART K:

FUGITIVE PARTICULATE MATTER

Section

212.301

212.302

212.

304

212.305

212

.

306

212.307

212.308

212.309

212.310

212.312

212.313

212.314

212.315

212.316

Fugitive

Particulate

Matter

Geographical

Areas

of

Application

Storage Piles

Conveyor

Loading

Operations

Traffic

Areas

Materials

Collected

by

Pollution

Control

Equipment

Spraying

or

Choke-Feeding

Required

Operating

Program

Minimum

Operating

Program

Amendment

to

Operating

Program

Emission

Standard

for

Particulate

Collection

Equipment

Exception for Excess Wind. Speed

Covering

for

Vehicles

Emission Limitations for Sources

in

Certain

Areas

SUBPART

L:

PARTICULATE MATTER

EMISSIONS

FROM

PROCESS

EMISSION

SOURCES

Section

212.321

212.322

212.323

212

.

324

New

Process

Sources

Existing Process Sources

Stock

Piles

Process

Emission

Sources

in

Certain

Areas

SUBPART

N:

FOOD

MANUFACTURING

Section

212.361

212.362

Corn

Wet

Milling

Processes

Sources

in

Certain

Areas

SUBPART 0:

PETROLEUM

REFINING,

PETROCHEMICAL

AND

130—429

---

36

CHEMICAL

MANUFACTURING

Section

212.381

Catalyst

Regenerators

of Fluidized Catalytic Converters

SUBPART

Q:

STONE,

CLAY,

GLASS

AND

CONCRETE

MANUFACTURING

Section

212.421

New

Portland

Cement

Processes

212.422

•

Portland

Cement

Manufacturing

Processes

212.423

Emission

Limits

for

the

Portland

Cement

Manufacturing

Plant

Located

in

LaSalle

County,

South

of

the

Illinois.

River

212.424

Fugitive

Particulate

Matter

Control

for

the

Portland

Cement Manufacturing Plant and Associated Quarry

Operations

Located

in

LaSalle

County,

South

of

the

Illinois

River

212.425

Sources

in

Certain

Areas

SUBPART

R:

PRIMARY

AND

FABRICATED METAL PRODUCTS AND

MACHINERY

MANUFACTURE

Section

212.441

212.442

212.443

212.444

212.445

212.446

212.447

212.448

212.449

212.450

212.451

212.452

212.455

212 .456

212 .457

212.458

Steel

Manufacturing

Processes

Beehive Coke Ovens

By-Product Coke Plants

Sinter

Processes

Blast

Furnace

Cast

Houses

Basic

Oxygen

Furnaces

Hot

Metal

Desulfurization

Not

Located

in

the

BOF

Electric

Arc

Furnaces

Argon—Oxygen Decarburization Vessels

Liquid

Steel

Charging

Hot

Scarf ing

Machines

Measurement

Methods

Highlines

on

Steel

Mills

Certain Small Foundries

Certain Small Iron—melting Air Furnaces

Sources

in

Certain

Areas

SUBPART S:

AGRICULTURE

Grain

Handling

and

Drying

in

General

Grain

Handling

Operations

Grain

Drying

Operations

Sources

in

Certain

Areas

SUBPART T:

CONSTRUCTION

AND

WOOD PRODUCTS

Section

212.681

Grinding,

Woodworking,

Sandblasting

and

Shotbbasting

Section

212.461

212.462

212.463

212.464

130—430

---

37

2l2.Appendix A

Rule into Section Table

212.Appendix

B

Section

into

Rule

Table

2l2.Appendix C

Past Compliance Dates

Illustration

A:

Allowable

Emissions

from

Solid

Fuel

Combustion Emission Sources Outside Chicago

Illustration

B:

Limitations

for

all

New

Process

Emission

Sources

Illustration

C:

Limitations

for

all

Existing

Process

Emission

Sources

Illustration

D:

McCook

Vicinity

Map

Illustration

E:

Lake

Calumet

Vicinity

Map

Illustration

F:

Granite

City

Vicinity

Map

AUTHORITY:

Implementing

Section

10

and

authorized

by

Section

27

of

the

Environmental

Protection

Act

(Ill.

Rev.

Stat.

1989,

ch.

111

1/2,

pars.

1010

and

1027).

SOURCE:

Adopted

as

Chapter

2:

Air

Pollution,

Rules

202

and

203:

Visual and Particulate Emission Standards and Limitations,

R7l—23,

4

PCB

191,

filed

and

effective

April

14,

1972;

amended

in

P17—15,

32

PCB

403,

at

3

Ill.

Reg.

5,

p.

798,

effective

February

3,

1979;

amended

in

R78—bO,

35

PCB

347,

at

3

Ill.

Reg.

39,

p.

184,

effective

September

28,

1979;

amended

in

R78—l1,

35

PCB

505,

at

3

Ill.

Reg.

45,

p.

100,

effective

October

26,

1979;

amended

in

R78—9,

38

PCB

411,

at

4

Ill.

Reg.

24,

p.

514, effective June 4,

1980;

amended

in

R79—ll,

43

PCB

481,

at

5

Ill.

Reg.

11590,

effective

October

19,

1981;

codified

at

7

Ill.

Reg.

13591;

amended

in

R82—1

(Docket

A),

10

Ill.

Reg.

12637,

effective July

9,

1986;

amended

in

R85—33

at

10

Ill.

Reg.

18030,

effective

October

7,

1986;

amended

in

R84-48

at

11

Ill.

Reg.

691,

effective

December 18,

1986; amended in R84—42

at

11

Ill.

Reg.

1410,

effective December 30,

1986; amended in R82-1

(Docket

B)

at

12

Ill.

Reg.

12492, effective July 13,

1988; amended

in R9b—10 at

15

Ill.Reg.

15595, effective October 11,

1991; amended in R9b-6 at

15 Ill.Reg.

____,

effective October 14,

1991; amended in P21-22

at

16 Ill. Reg.

‘

,

effective

___________________

SUBPART A:

GENERAL

Section 212.107

Measurement Method for Visible Emissions

Detection of visible emissions from both process emission sources

and fugitive particulate matter emission sources shall be

conducted

in accordance with Method 22, 40 CFR 60, Appendix A,

incorporated by reference in Section 212.113, except that the

length of the observing period shall be at the discretion of the

observer, but not less than one minute.

(Source:

Added at

16 Ill.Reg.

,

effective

__________

______

.)

130—431

---

38

Section

212.108

Measurement

Methods

for

PM-b

Emissions

~j

Emissions

of

PM-b

shall

be

measured

by

any

of

the

following

methods

at

the

option,

of

the

owner

or

operator

of

an

emissions

source.

fl

Method

201,

40

CFR

51,

Appendix

N,

incorporated

by

reference

in

Section

212.113.

fl

Method 201A,

40

CFR

51.

Appendix

N,

incorporated

by reference in Section 212.113.

,~j

Method

5.

40

CFR

60,

Appendix

A,

incorporated

by

reference

in

Section

212.113,

provided

that

all

particulate

matter

measured

by

Method

5

shall

be

considered

to

be

PM-b.

~j

The

volumetric

flow

rate

and

gas

velocity

shall

be

determined in accordance with

methods

1.

lA,

2,

2A.

2C,

2D,

3

or

4,

40

CFR

60

Appendix

A,

incorporated

by

reference

in

Section

212.113.

~j

Upon

a

written

notification by the Illinois

Environmental Protection Agency (Agency), the owner or

operator of a PM-b

emission source subiect to this

Section shall conduct the applicable testing for PM-b

emissions,

opacity, or visible emissions at such

person’s

own

expense.

to

demonstrate

compliance.

Such

test

results

shall

be

submitted

to

the

Agency

within

30

days of conducting the test unless an alternative time

for

submittal

is

agreed

to

by

the

Agency.

~.j

A

person

planning

to

conduct

testing

for

PM-b

emissions

to

demonstrate

compliance

shall

give

written

notice

to

the

A~ency of

that

intent.

Such

notification

shall

be

given

at

least

30

days

prior

to

initiation

of

the

test

unless

a

shorter

pre—notification

is

agreed

to

by

the

Agency.

Such notification shall state the

specific

test

methods

from

subsection

(a)

that

will

be

used.

~

The

owner

or

operator

of

an

emission

source

subject

to

this

Section

shall

retain

-records

of

all

tests

which

are

performed.

These

records

shall

be

retained

for

at

least

three

years

after

the

date

a

test

is

performed.

~j

This

Section

shall

not

affect

the

authority

of

the

United

States

Environmental

Protection

Agency

under

Section

114

of

the

Clean

Air

Act

(42

U.S.C.

~

7414

(1990))..

130—432

---

39

(Source:

Added

at

16

Ill.

Reg.

______,

effective

______________

212. 109

Measurement,Methods for Opacity

Except

as

otherwise

provided

in

this

Part,

and

except

for

the

methods

of

data

reduction

when

applied

to

Sections

212.122

and

212.123, measurements of opacity shall be conducted in accordance

with

Method

9.

40

CFR

Part

60~ A~~endixA,

incorporated bY

reference

in

Section

212.113.

except

that

for

roadways

and,

parkin~

areas

the

number

of

readings

required

for

each

vehicle

pass

will

be

three taken at 5-second intervals.

The first

reading

shall

be

at

the

point

of

maximum

opacity

and

second

and

third

readings

shall

be

made

at

the

same

point,

the

observer

standing

at

right

angles

to

the

plume

at

least

15

feet

away

from

the

plume

and

observing

4

feet

above

the

surface

of

the

roadway

or

parking

area.

After four vehicles have

passed,

the

12

readings will be averaged.

(Source:

Added at 16

Ill. Reg.

______,

effective

______________

Section 212.110

Measurement Methods For Particulate Matter

a)

Particulate Matter Measurement.

Particulate matter

emissions from stationary emission sources subject to

this Part shall be conducted in accordance with 40 CFR

60 Appendix A Method~5,

5A,

SD, or 5E, as incorporated

by reference in Section 212.113.

b)

Flow Rate and Gas Velocity Measurement.

The volumetric

flow rate and gas velocity shall be determined in

accordance with 40 CFR 60, Appendix A, Methods

1,

1A,

2,

2A,

2C,

2D,

3

and

4,

incorporated

by

reference

in

Section 212.113.

c)

Opacity Measurement.

Measurement

of

opacity shall be

conducted in accordance with 40 CFR 60, Appendix A,

Method

9 and 40 CFR 60.675(c) and

(d), incorporated by

reference in Section 212.113.

d)

Visible

Emissions

Measure.

DctcctionA determination as

to

the

presence

or

absence

of

visible

emissions from

all

process

emission

sources

and

fugitive

particulate

emission

sources

required

to

meet

a

“no

vi3ibbe

cmi33iono”

3tandard,

excePt

with

respect

to

Section

212.301,

shall be conducted in accordance with 40 CFR

60, Appendix A, Method 22,

incorporated by reference in

Section 212.113, except that the length of the

observing period shall be at the discretion of the

observer, but not less than one minute.

130—433

---

40

e)

Test Methods

for

PM—b

Emissions.

Emissions of PM—b

shall be measured by any of the following methods at

the option of the owner or operator of an emissions

source.

1)

40 CFR 51, Appendix M, Method 201, incorporated by

reference in Section 212.113.

2)

40 CFR 51, Appendix H, Method 201A, incorporated

by reference in Section 212.113.

3)

40 CFR 60, Appendix A, Method

5,

incorporated by

reference in Section 212.113, provided that all

Particulate Matter measured by Method 5 shall be

considered to be PM-bc.

f)

Test Methods for Condensible PM-lU Emissions.

Emissions of condensibbe PM-b

shall be measured by 55

Fed. Reg. 41546 Method 202 incorporated by reference in

Section 212.113.

g)

Upon a written notification by the Agency, the owner or

operator of a PM—b

emission source subject to this

Part shall conduct the applicable testing for PM-b

emissions, condensible PM—lU emissions, opacity, or

visible emissions at such person’s own expense, to

demonstrate compliance.

Such test results shall be

submitted to the Agency within 30 days of conducting

the test unless an alternative time for submittal is

agreed to by the Agency.

h)

A person planning to conduct testing for PM-b

or

condensible PM-b

emissions to demonstrate compliance

shall give written notice to the Agency of that intent.

Such notification shall be given at least 30 days prior

to the initiation of the test unless a shorter period

is agreed to by the Agency.

Such notification shall

state the specific test methods from this Section that

will be used.

i)

The owner or operator of an emission source subject to

this Part shall retain records of all tests which are

performed.

These records shall be retained for at

least three years after the date a test is performed.

j)

This Section shall not affect the authority of the

United States Environmental Protection Agency under

Section 114 of the Clean Air Act

(42 U.S.C.A.

Par. 7401

et seq.

(1990)).

(Source:

Amended at 16 Ill.Reg.

_______,

effective

____________

130—434

---

41

Section 212.113

Incorporations by Reference

The following materials are incorporated by reference.

,These

incorporations do not include any later amendments or editions.

a)

Ringelmann Chart, Information Circular 833

(Revision of

IC7718),. Bureau of Mines, U.S. Department of Interior,

May

1,

1967.

b)

,

40

CFR

60,

Appendix

A

(1990):

1)

Method

1:

Sample

and

Velocity

Traverses

for

Stationary

Sources;

2)

Method

IA:

Sample

and

Velocity Traverses for

Stationary

Sources

with

Small

Stacks

or

Ducts;

3)

Method

2:

Determination

of

Stack

Gas

Velocity

and

Volumetric

Flow

Rate

(Type

S

pitot

tube);

4)

Method

2A:

Direct

Measurement

of

Gas

Volume

Through

Pipes

and

Small

Ducts;

5)

Method

2C:

Determination

of

Stack

Gas

Velocity

‘and Volumetric Flow Rate in Small Stacks or Ducts

(Standard

Pitot

Tube);

6)

Method 2D:

Measurement of Gas Volumetric Flow

Rates in Small Pipes and Ducts;

7)

Method 3:

Gas Analysis for Carbon Dioxide,

Oxygen,

Excess Air, and Dry Molecular Weight;

8)

Method

4:

Determination of Moisture Content in

Stack Gases;

9)

Method 5:

Determination of Particulate Emissions

From Stationary Sources;

~J

Method 5A:

Determination of Particulate Emissions

From the Asphalt Processing and Asphalt Roofing

Industry

3JJ

Method 5D:

Determination of Particulate Matter,

Emissions From Positive Pressure Fabric Filters

3~j) Method SE:

Determination of Particulate Emissions

From the Wool Fiberglass Insulation Manufacturing

Industry

~9U)Nethod

9:

Visual Determination of the Opacity of

Emissions from Stationary Sources;

130—435

---

42

~*,~j)Method22:

Visual Determination of Fugitive

Emissions from Material Sources and Smoke

Emissions from Flares.

C)

40 CFR 51 Appendix N

(1990):

1)

Method 201:

Determination of PM-lU Emissions:

2)

Method 2UbA:

Determination of PM-b

Emissions

(Constant Sampling Rate Procedure).

d)

40 CFR 60.672

(b)

,

(c),

(d), and

(e)

(1990).

e)

40 CFR 60.675(c)

and

(d)

(1990).

f)

ASAE Standard 248.2, Section

9,

Basis for Stating

Drying Capacity of Batch and Continuous-Flow Grain

Dryers, American Society of Agricultural Engineers,

2950 Niles Road,

St. Joseph, MI 49085.

g)

U.S. Sieve Series, ASTM-Ell, American Society of

Testing Materials,

1916 Race Street,

Philadelphia,

PA

19103.

h)

55 ~RFed. Reg.

41546,- (October 12,

1990), Method 202:

Determination of Condensible Particulate Emissions from

Stationary Sources.

(Source:

Amended at 16

Ill.

Reg.

______,

effective

___________

SUBPART E:

PARTICULATE

MATTER EMISSIONS FROM FUEL COMBUSTION

EMISSIONS SOURCES

Section 212.210

Emissions Limitations for Certain Fuel

Combustion Emission Sources Located in the

Vicinity of Granite City

a)

No person shall cause

or allow emissions of PM—b

into

the atmosphere to exceed 12.9 ng/J

(0.03 lbs. per

mnthtu)

of heat input from fuels other than natural gas

during any one hour period from any industrial fuel

combustion emissions source, other than in an

integrated iron and steel plant, located in the

vicinity of Granite City. which area is defined in

Section 212.324 (a). (1) (C)..

~j.

Compliance Date.

Sources shall comply with the

emissions limitations of this Section within one year

following its effective date, or by December 10,

1993,

whichever is earlier.

130—436

---

43

(Source:

Added at 16 Ill.

Reg.

______,

effective

___

SUBPART K:

FUGITIVE PARTICULATE MATTER

Section 212.302

Geographical Areas~of Application

,~j

Except for those operations subject to Subpart S

(Grain-Handling and Grain-Drying Operations)

that are

outside the areas defined in section 212.324(a) (1),

Sections 212.304 through 212.310, and 212.312 shall

apply to all mining operations (SIC major groups

10

through 14), manufacturing operations

(SIC major groups

20 through 39), and electric generating operations (SIC

group 491), which are located in the areas defined by

the boundaries of the following townships,

notwithstanding any political subdivisions contained

therein, as the. township boundaries were defined on

October

1,

1979,

in the following counties:

Cook:

All townships

Lake:

Shields, Waukegan, Warren

DuPage:

Addison, Winfield, York

Will:

DuPage,

Plainfield,

Lockport, Channahon,

Peotone,

Florence, Joliet

Peoria:

Richwoods,

Limestone, Hollis,

Peoria,

City of Peoria

Tazewell:

Fondulac,

Pekin, Cincinnati,

Groveland,

Washington

Macon:

Decatur, Hickory Point

Rock Island:

Blackhawk,

Coal Valley, Hampton, Moline,

South Moline, Rock Island, South Rock

Island

LaSable:

LaSalle, Utica

Madison:

Alton,

Chouteau, Colbinsvilbe,

Edwardsville, Fort Russell, Godfrey,

Granite City, Nameoki, Venice, Wood

River

St.

Clair:

Canteen, Caseyville,

Centerville,

St.

Clair, Stites, Stookey, Sugar Loaf,

Millstadt

~j

In the geographical areas defined in Section

212.324(a). (1), Sections 212.304 through 212.310,’

212.312, and 212.316 shall apply to all sources

identified in subsection

(a), and shall further apply

to the following operations:

grain-handling and

grain-drying

(Subpart S).

transportation,

communications,

electric, gas, and sanitary services

(SIC malor groups 40 through 49).

Additionally,

Sections 212.304 through 212.310, 212.312, and 212.316

shall apply to wholesale trade-farm supplies (SIC

130—43

7

---

44

Industry No.

5b9l)

located in the vicinity of Granite

City, as defined in Section 212.324(a) (1) (C).

,gj

Compliance Date.

Compliance with subsection

(b)

is

required one year following its effective date, or by

December 10,

b993, whichever is earlier.

(Source:

Amended at 16

Ill. Reg.

______,

effective

___________

Section ~12.309

Operating Program

~j

The sources described in Sections 212.304 through

212.308 and Section 212.316 shall be operated under the

provisions of an operating program, consistent with the

requirements set forth in Sections 212.310 and 212.312

of this Part,

and prepared by the owner or operator and

submitted to the Agency for its review.

Such operating

program shall be designed to significantly reduce

fugitive particulate matter emissions.

~j

Compliance Date.

The amendment to this section~

incorporating the applicability of Section 212.316

shall apply one year following its effective date or on

December 10,

1993. whichever is earlier.

(Source:

Amended at 16

Ill.

Reg.

______,

effective

____________

Section 212.316

Emission Limitations For Sources in Certain

Areas

~J

Applicability.

This Section shall apply to those

operations specified in Section 212.302 and that are

located in areas defined in Section 212.324(a) (1).

~j

Emission Limitation for Crushing and Screening

Operations.

No person shall cause or allow fugitive

particulate matter emissions generated by the crushing

or screening of slag, stone, coke or coal to exceed an

opacity of 10.

~j

Emission Limitations for Roadways or Parking Areas.

No

person shall cause or allow fugitive particulate matter

emissions from any roadway or parking area, to exceed an

opacity of 10,

except that the opacity shalb not

exceed 5

at quarries with a capacity to produce more

than

1 million tons per year of aggregate.

~J

Emission Limitations for Storage Piles.

No person

shall cause or allow fugitive particulate matter

130—438

---

45

emissions from any storage pile to exceed an opacity of

10,

to be measured four feet from the pile surface.

~j

Additional Emissions Limitations for the Granite City

Vicinity as’Defined in Section 212.324(a) (1) (C).

.fl

EmisSions Limitations for Roadways or Parking

Areas Located at Slag Processing Facilities or

Integrated Iron and Steel Manufacturing Plants.

No person shall cause or allow fugitive

particulate matter emissions from any ‘roadway or

parking area located at a slag processing facility

or_integrated iron and steel manufacturing plant

to exceed an opacity of 5.

21

Emissions Limitations for Marine Terminals.

~j

No person shall cause or allow fugitive

particulate matter emissions from any loading

spouts for truck or railcar to exceed an

opacity of 10.

~j

No person shall cause or allow fugitive

particulate matter emissions generated at

barge unloading, dump ‘pits, or conveyor

transfer points including, but not limited

to, transfer onto and off of

a conveyor, to

exceed an opacity of 5.

fl

Emission Limitation for All Other Sources.

Unless a

source has been assigned a particulate matter, PM-b.

or fugitive particulate matter emissions limitation

elsewhere in this Section or in Subparts R or

S. no

person shall

cause or allow fugitive particulate matter

emissions from any source to exceed an opacity of 20.

gJ

.Recordkeeping and Reporting

fl,

The owner or operator of any fugitive particulate

matter_emission source subiect to this Section

shall keep written records of the application of

control measures as may be needed for compliance

with the opacity limitations of this Section and

shall submit to the Agency an annual report’

containing a summary of such information.

21

The records required under this subsection shall

include at least the following:

~j

the name and address of the plant

130—439

---

46

~

the name and address of the owner and/or

pp~rator

of

the plant

çj

a map or diagram showing the location of all

emission sources controlled including the

location,

identification,

length, and width

of roadways

~

for each application of water or chemical

solution to roadways by truck:

the name and

location of the roadway controlled,

application rate of each truck,

frequency of

each application, width of each application,

ident fication of each truck used,

total

quantity of water or chemical used for each

application and, for each application of

chemical solution, the concentration and

identity of the chemical.

~j

for application Of physical or chemical

control agents, the name of the agent1

application rate and frequency,

and total

quantity of agent and,

if diluted, percent of

concentration, used each day

,~j

a bog recording incidents when control

measures were not used and a statement of

explanation.

~j.

Copies of alb records required by this Section

shall be submitted to the Agency within ten

(10)

working days of a written request by the Agency

and shall be transmitted to the Agency by a

company-designated person with authority to

release such records.

,j)

The records required under this Section shall be

kept and maintained for at least three

(3)

years

and shall be available for inspection and copying

by Agency representatives during working hours.

~j

A quarterly report shall be submitted to’the

Agency stating the following:

the dates any

necessary control measures were not implemented,

a

listing of those control measures, the reasons

that the control measures were not implemented,

and any corrective actions taken.

This

information includes, ‘but is not limited to,

those

dates when controls were not applied based on a

belief that application of such control measures

would have been unreasonable given prevailing

atmospheric conditions, which shall constitute a

130—440

---

47

defense to the requirements of this Section.

This

report shall

be’ submitted to the Agency 30

calendar days from the end of a quarter.

,

Quarters

end March 31, June 30, September 30, and December

31.

~j

Compliance

Date.

Sources shall comply with the

emissions limitations and recordkeeping and reporting

requirements of this Section within one year following

the effective date of this Section, or by December 10,

1993. whichever is earlier.

(Source:

Added at 16 Ill. Reg.

________,

effective

____________

SUBPART

L:

PARTICULATE MATTER EMISSIONS FROM

PROCESS EMISSION SOURCES

Section 212.324

Process Emission Sources in Certain Areas

~j

Applicability.

j)~.

This Section shall apply to any process emission

source located in any of the following areas:,

AL

That area bounded by lines from Universal

Transmercator

(UTM)

coordinate ‘428000mE,

463b000mN, east to 435000mE, 463b000mN,

south

to 435000mE,

4623000mN,

west to 428000mE,

4623000mN, north to 428000mE, ‘463b000mN,

in

the vicinity of McCook in Cook County, as

shown in Illustration D

~

That area bounded by lines from Universal

Transmercator

(UTM)

coordinate 445000mE,

4622l80mN, east to 456265mE, 4622180mN,

south

to 456265E, 4609020N, west to 445000mE,

4609020mN, north to 445000mE, 4622l80mN,

in

the vicinity of Lake Calumet in Cook County,

as shown in Illustration E

~

That area bounded by lines from Universal

Transmercator

(UTN) coordinate 744000mE,

4290000mN,

east to 753000mE, 4290000mN, south

to 753000mE,

4283000mN, west to 744000mE,

4283000mN,

north to 744000inE, 4290000mN,

in

the vicinity of Granite City in Madison

County,

as shown in Illustration

F.

21

This Section shall not alter the applicability of

Sections 212.321 and 212.322 of this Part.

130—44 1

---

48

~j.

The emission limitations of this Section are not

applicable to any source sub-ject to a specific

emissions standard or limitation contained in any

of the following Subparts:

IlL

Subpart N, Food Manufacturing;

(ii)

Subpart 0,

Stone.

Clay, Glass and

Concrete Manufacturing;

(iii)

Subpart R, Primary and Fabricated Metal

Products and Machinery Manufacture;

and,

(iv)

Subpart S, Agriculture.

~j

General Emission Limitation.

Except as otherwise

provided in this Section, no person shall cause or

allow the emission, into the atmosphere, of PM-b

from

any process emission source to exceed 68.7 mg/scm (0.03

g,r/scf) during any one hour period.

cj

Alternative Emission Limitation.

In lieu of the

emission limit of 68.7 mg/scm

(0.03 gr/scf) contained

in subsection

(b), no person shall cause

or allow the

emissions of the following sources to exceed the

corresponding limitations in the following table:

Source

Emissions Limit

Metric

English

fl

Shotblasting emissions

22.9 mg/scm

0.01

sources in the Village

gr/scf

of McCook equipped with

fabric filter(s)

as of

June

1.

1991

aL

All process emissions

5

opacity

5

opacity

sources at manufacturers

of steel wool with soar

pads located in the

Village of McCook

~j

Exceptions.

The mass emission limits contained in

subsections

(b) and

(c)

shall not apply to those

sources with no visible emissions other than fugitive

particulate matter.

,~j

Special Emi,ssions Limitation for Fuel-Burning Process

Emissions Sources in the Vicinity of Granite City.

No

person shall cause or allow emissions of PM—lU into the

atmosphere to exceed 12.9 ng/J (0.03

lbs. per mmbtu)

of

130—442

---

49

heat input from the burning of fuel other than natural

gas at any process emissions source located

in the

vicinity of Granite City as defined in subsection

(a) (1) (C)

fl.

Maintenance and Repair.

For any process emission

source sublect to subsection

(a)

•

the owner or operator

shall maintain and repair all air pollution control

e~ipmentin a manner that assures that the emission

limits and standards in this Section shall be met at

all times.

This Section shall not affect the

applicability of Section 201.149.

Proper maintenance

shall include the following minimum requirements:

fl

Visual

inspections of air pollution control

equipment

21

Maintenance of an ade~ateinventory of spare

parts;

and

fl

Expeditious repairs, unless the source

is

shutdown.

gj

Recordkeeping of Maintenance and Repair.

fl

Written records of inventory and documentation of

inspections, maintenance, and repairs of all air

pollution control equipment shall be kept in

accordance with subsection

(f) of this Section.

21

The owner or operator shall document any period

during which any process emission source was in

operation when the air pollution control equipment

was not in operation or was malfunctioning so as

to cause an emissions level in excess of the

emissions limitation.

These records shall include

documentation of causes for pollution control

equipment not operating or such malfunction and

shall state what corrective actions were taken and

what repairs were made.

fl

A written record of the inventory of all spare

parts not readily available from local suppbiers

shall be kent and updated.

il

Copies of all records required by this Section

shall be submitted to the Agency within ten

(10)

working days of a written request by the Agency.

,~j

The records required under this Section shall be

kept and maintained for at least three

(3) years

130—443

---

50

and shall be available for inspection and copying

by Agency representatives during working hours.

.~j.

Upon written request by the Agency ~a report shall

be submitted to the Agency for any period

specified in the request stating the following:

the dates during which any process emissions

source was in operation when the air pollution

control equipment was not in operation or was not’

operating properly. documentation of causes for

pollution control equipment not operating or not

operating properly, and a statement of what

corrective actions were taken and what repairs

were made.

~j

Compliance Date.

Sources shall comply with the

emissions limitations and recordkeeping and reporting

requirements of this Section within one year of the

effective date of this Section, or by December 10,

1993, whichever is earlier.

(Source:

Added at 16 Ill. Reg.

______,

effective

______________

SUBPART N:

FOOD MANUFACTURING

2b2.362

Sources in Certain Areas

~

Applicability.

fl

Subsections

(b) (1) through

(b) (4)

shall apply to

those sources engaged in food manufacturing, and

located in the Village of Bedford Park west of

Archer Avenue and in the area defined in Section

212.324 (a) (1) (A).

21

Subsection

(b) (5) applies to an instant tea

manufacturing plant in Granite City,

as defined in

Section 212.324(a) (1) (C).

~j

Emission Limitation.

No person shall cause or allow

the emission of PM-b. other than that of fugitive

particulate matter,

into the atmosphere to exceed the

following limits during any one hour period:

fl

22.9 mg/scm (0.01 gr/scf)

for dextrose dryers,

dextrose melt tank systems, bulk dextrose loading

system, house dry dextrose dust system, dextrose

bagging machine dust system; dextrose expansion

dryer/cooler and packing system and 2034 dextrose

dryer/cooler dust collecting system

130—444

---

51

21

34.3 mg/scm (0.015 gr/scf)

for feed dryers, gluten

dryers,

germ dryers, heat recovery scrubbers

~j

68.7 mg/scm

(0.03 gr/scf)

for germ cake transport

systems, spent flake transport/cooling systems.

bleaching clay system, dust pickup bin system in

Building 26, and pellet cooler systems

j).

45.8 mg/scm

(0.02 gr/scf)

for germ transport

systems, starch dust collection systems, dicalite

system,

starch processing/transport systems.

starch dryers, starch transport systems, calcium

carbonate storage system, starch loading systems,

corn unloading systems,

germ

transfer towers,

dextrose transport systems, soda ash unloading

system, corn silo system,

filter aid systems,

spent flake storage systems, corn cleaning

transport systems,

feed transport cooling system,

gluten cooling system, gluten transport system,

feed dust system. gluten dust system. pellet dust

system,

spent flake transport system, and rail car

maintenance system building and dextrose expansion

milling and storage systems.

~

22.9 mg/scm

(0.01 gr/scf) for any process

emissions source at an instant tea manufacturing

plant in Granite City, except the spray dryer, raw

tea storage silo,

and instant tea filling

machines.

~j

Exceptions.

The emission limits contained in

subsection

(b)

shall not apply to those sources with no

visible emissions other than fugitive matter.

~j

Maintenance. Repair, and Recordkeeping.

The

requirements of subsections

(f) and

(a)

of Section

212.324 shall also apply to this Section.

g)

Compliance Date.

‘

Sources shall comply with the

emissions limitations and recordkeeping and reporting

requirements of this Section within one year of the

effective date of this Section, or by December 10,

b993, whichever is earlier.

(Source:

Added at 16 Ill. Reg.

______,

effective

____________

SUBPART

Q:

STONE,

CLAY, GLASS

AND’ CONCRETE MANUFACTURING

212.425

sources in Certain Areas

130—445

---

52

,~j

Applicability.

This Section shall apply to those

sources located in those areas defined in Section

212.324 (a) (1)

~j

Emission Limitation.

No person shall cause or allow

the emission of PM-b.

other than that of fugitive

particulate matter,

into the atir~osphereto exceed the

following limits during any one hour period:

fl

57.2 mg/scm (0.025 gr/scf)

for coater and cooling

loop ventilator at roofing asphalt manufacturing

plant located in the Village of Summit

21

34.3 mg/scm

(0.015 gr/scf)

for mineral filler

handling sources at roofing asphalt manufacturing

plant located in the Village of Summit

fl

0.03 kg/Mg

(0.06 lb/T)

of asphalt mixed for

asphalt mixer at roofing asphalt manufacturing

plant located in the Village of Summit

il

91.6 mg/scm

(0.04 gr/scf)

for roofing asphalt

blowing stills, except stills Nos.

1 and 2, at

roofing asphalt manufacturing plant located in thE

Village of Summit

,~j

45.8 mg/scm

(0.02 gr/scf)

for kilns in the lime

manufacturing industry

~j

22.9 mg/scm

(0.01 gr/scf)

for all other process

emission sources in the lime manufacturing

industry

fl

0.325 kg/Mg

(0.65 lb/T)

of glass produced for all

glass melting furnaces.

~j

Exceptions.

The emission limits contained in

subsection

(b) of this Section shall not apply to thosE

sources with no visible emissions other than fugitive

particulate matter.

~j

Maintenance. Repair, and Recordkeeping.

The

requirements of subsections

(f) and

(g)

of Section

212.324 shall also apply to this Section.

~j

Compliance Date.

Sources shall’ comply with the

emissions limitations and recordkeeping and reporting

requirements of this Section within one year of the

effective date of this Section, or by December 10,

1993, whichever is earlier.

130—446

---

53

(Source:

Added at 16 Ill. Reg.

______,

effective

SUBPART R:

PRIMARY AND FABRICATED METAL PRODUCTS

AND MACHINERY

MANUFACTURE

212.458

Sources in Certain Areas

~j

Applicability.

This Section shall apply to those

sources located

in those areas defined in Section

212.324(a) (1).

~j

Emission Limitation.

No person shall cause or allow

emissions of PM-b,

other than that of fugitive

particulate matter,

into the atmosphere to exceed the

following limits during any one hour period:

fl

15.9

ng/J

(0.037 bbs. per mmbtu)

of heat input

from any fuel combustion source located at the

steel Plant between 106th and 111th Streets in

City of Chicago

21

22.9 ma/scm

(0.01 gr/scf)

for the basic oxygen

furnace additive systems in the Village of

Riverdale

~j

4.3 ng/J (0.01 bbs. per minbtu)

of heat input from

the burning of fuel in the soaking pits in the

Village of Riverdale

~j

64.08 mp/scm (0.028 gr/scf)

from the electrostatic

precipitator discharge of the basic oxygen process

in the Village of Riverdabe

~j

45.8 mg/scm

(0.02 gr/scf)

from the pickling

process at a steel plant in the Village of

Riverdale

~j

5

opacity for coal handling systems equipped with

fabric filter(s) at steel plant located in the

City of Chicago

fl

22.9 ma/scm

(0.01 ar/scf)

from any process

emissions source located at integrated iron and

steel Plants in the vicinity of Granite City,

as

defined in Section 212.324(a) (1) (C), except as

otherwise provided in this Section or in Sections

212.443 and 212.446

~J

5

opacity for continuous caster spray chambers or

continuous casting operations at steel plants in

130—44 7

---

54

the vicinity of Granite City,

as defined in

Section 212.324(a) (1)

(C).

~j

32.25 ng/J

(0.075 lbs per

mmbtu)

of heat input

from the burning of coke oven gas at all sources

at steel plants in the vicinity of Granite City,

as defined in Section 212.324(a) (1) (C)

J,~QJ

38.7 ng/J (0.09 lbs. per mmbtu)

of heat input from

the slab furnaces at steel plants in the vicinity

of Granite City,

as defined in Section

212.324 (a) (b) (C);

111

22.9 mg/scm

(0.01 gr/scf)

for all process

emissions sources at secondary lead processing

plant located in Granite City,

except the salt

flux crusher

jfl

22.9 ma/scm

(0.01 gr/scf). for any melting furnace

at secondary aluminum smelting and refining plant

in the vicinity of Granite City,

as defined in

Section 2b2.324(a) (1). (C).

~j.

45.8 mg/scm

(0.02 gr/scf).

from No.

6 mill brusher,

and metal chip handling system at secondary

aluminum smelting and refining plant located in

the vicinity of Granite City,

as defined in

Section 212.324(a). (1). (C).

141

0.05 kg/Mg

(0.01 lb/T)

per ton of sand processed

from ‘molding sand forming systems at steel foundry

plant located in Granite City

~j

0.01 kg/Mg

(0.02 lbs/T) per ton of sand processed

from recycle sand shakeouts at steel foundry plant

located in Granite City

~j

22.9 mg/scm

(0.01 gr/scf)

for all other process

emissions sources at steel foundry plant in

Granite City,

except the sand dryer,

sand cooler,

chill tumbler, paint booth, chromite reclamation

and core baking ovens

~,fl

41.2 mg/scm

(0.018 gr/scf)

for cold rolling mill

emissions sources at metal finishing plant located

in the Village of McCook

.3fl

2.15 ng/J (0.005 bbs/mmbtu)

of heat input from the

burning of fuel in any process emission source at

secondary aluminum smelting and refining plant

and/or aluminum finishing plant

130—448

---

55

~j~j 22.9 mg/sôm (0.01 gr/scf).

from dross pad, dross

cooling, and dross mixing sources at secondary

aluminum smelting and refining plant and/or

aluminum

finishing

plant

ZQI

12.9 ng/J (0.03

lbs/mmbtu)

of heat input from any

fuel combustion emission source that heats air for

space heating purposes at secondary aluminum

smelting and refining ~bant located in the

vicinity of Granite City.

as defined in Section

212.324 (a) (1) (C

)

211.

68.7

mg/scm

(0.03

gr/scf)

for

any

holding

furnace

at

secondary

aluminum

smelting

and

refining

plant

in

the

vicinity

of

Granite

City,

as

defined

in

Section

212.324

(a)

(1) (C)

.221

2.15 ng/J

(0.005 lbs per

mmbtu)

of

heat

input

from

the

steel

works

boilers

located

at

the

steel

making facilities at steel plant in the vicinity

of

Granite

City,

as

defined

in

Section

212.324

(a)

(1)

(C

)

~

29.71 kg (65.5 bbs)

for the total of all basic

oxygen furnace processes described in Section

212.446(a)

and

located

at

steel

plant

in

the

vicinity

of

Granite

City,

as

defined

in

Section

212.324

(a)

(1) (C)

,a41

North

and

South furnaces at secondary aluminum

smelting and refining plant located in the

vicinity of Granite City,

as defined in Section

212 .324

(a) (1)

(C),

cannot

be

operated

simultaneously

~j

Magnesium pot furnaces at secondary aluminum

smelting and refining ~1ant located in the

vicinity of Granite City,

as defined in Section

212.324(a) (1) (C), can be operated only one line at

a

time

~fl

2.15

~g/J

(0.005

lbs/inmbtu)

of heat input from any

fuel

combustion

source at secondary aluminum

smelting and refining plant and/or aluminum

finishing

plant

except

as

provided

in

subsection

(b)

(20

)

221

91.6

mg/scm

(0.040

gr/scf)

and

o.4s

kg/hr

(1

lb/hr)

for

melting

furnaces

Nos.

6.

7.

and

8

at

metal finishing plant in the Village of McCook,

with

operation

limited

to

no

more

than

two

of

these

furnaces

at

one

time

130—449

---

56

j~j

183

mg/scm

(0.080

ar/scf)

and

0.91

kg/hr

(2

lbs/hr)

for holding furnaces Nos.

6,

7, and

8 at

metal

finishing

plant

in

the

Village

of

McCook,

with

operation

limited

to

no

more

than

two

of

these furnaces at one time

~j

54.9 mp/scm

(0.024 gr/scf) and 1.81 kg/hr

(4

lbs/hr)

for

melting

furnaces

Nos.

24,

25,

and

26

at metal finishing ~1ant in the Village of McCook

.~Qj

34.3

mg/scm

(0.015

gr/scf)

and

1.81

kg/hr

(4

lbs/hr)

for

melting

furnaces

Nos.

27,

28.

29,

and

30

at

metal

finishing

plant

in

the

Village

of

McCook

,~JJ

32.0

mp/scm

(0.014

gr/scf)

and

0.45

ku/hr

(1

lb/hr)

for

holding

furnaces

Nos.

24,

25,

and

26

at

metal

finishing

~bant

in

the

Village

of

McCook,

except

that

during

fluxing operation those

furnaces may emit 195 mg/scm (0.085 gr/scf) and

2.72 kg/hr

(6 bb/hr)

~21

34.3 ma/scm

(0.015 gr/scf) and 0.45 kg/hr

(1

lb/hr)

for holding furnaces Nos.

27.

28,

29, and

30 at metal finishing plant

in the Village of

McCook, except that during fluxing operation those

furnaces may emit 217 mg/scm (0.095 gr/scf)

and

2.72 ku/hr

(6 lb/hr)

~j

Fluxing operations at holding furnaces Nos.

24,

25,

26,

27,

28.

29, and 30 at metal finishing

plant in the Village of McCook shall be limited to

no more than three at any one time.

gj

Exceptions.

The mass emission limits contained in

subsection

(b)

shall not apply to those sources with no

visible emissions other than that of fugitive

particulate matter.

,~j

Maintenance, Repair, and Recordkeeping.

The

requirements of subsections

(f) and

(g)

of Section

212.324 shall also apply to this Section.

~j

Compliance Date.

Compliance with this Section

is

required by December 10.

1993.

(Source:

Added at 16 Ill.Reg.

,

effective

________

SUBPART

S:

AGRICULTURE

130—450

---

57

Section

212.464

Sources

in

Certain

Areas

~j

Applicability.

Notwithstanding

Section

212.461,

this

Section shall apply to those sources located in the

Lake

Calumet

area

as’ defined

in

Section

212.324(a)

(b)(B).

~j

Emission Limitations

fl

No

person

shall

cause

or

allow

the

emission.

of

PM—

10,

other

than

that

of

fugitive

particulate

matter,

into

the

atmosphere

to

exceed

22.9

mg/scm

(0.01

gr/scf).

during

any

one

hour

period

from

any

process

emissions

source

engaged

in

the

drying,

storing,

mixing

or

treating

of

grain

except

for

column

grain

dryers;

in

addition,

no

person

shall

cause or allow visible emissions of PM—b

other

than fugitive particulate matter from grain

conveying,

transferring, loading, or unloading

operations,

including garners,

scales, ‘and

cleaners.

21

No person shall cause or allow the emission of

fugitive particulate matter into the atmosphere

from barges and other watercraft. truck or rail

loading or unloading systems to exceed the limits

specified in Section 212.123.

~

Column grain dryers shall not be eligible for the

exemptions as provided in SectiOn 212.461(g).

Exceptions.

The mass emission limits contained in

subsection

(b)

shall not apply to those sources with no

visible emissions other than fugitive particulate

matter.

Maintenance, Repair, and Recordkeeping.

The

requirements of subsections

(f) and

(g)

of Section

212.324 shall alsO apply to this Section.

Compliance Date.

Sources shall comply with the

emission limitations and recordkeeping and reporting

requirements of this Section within one year.folbowing

the effective date of this Section, or by December 10,

1993, whichever is earlier.

(Source:

Added at 16 Ilb.Reg.

________,

effective

130=45 1

---

58

Illustration

MCCOOk Vicinity

4631000

4629000

4627000

4625000

4623000

429000

43

lOOC)

43300()

435000

130—4 52

---

59

Illustration

Lake

Calumet

Vicinity

462

‘1202

~6

190’~’)0

4617002

~“:220

42

‘1000

AR

1

“fl’~fl

~1,,

4

609000

446320

448000

450002

452000

454000

45600C

130—453

---

60

Granite City Vicinity’

4290000

4288000

4286000

4284000

744000

746000

748000

750000

752000

130—454

---

61

IT

IS

SO

ORDERED.

I,

Dorothy

M.

Gunn,

Clerk

of

the

Illinois

Pollution

Control

Board,

hereby

certify

that

the

above

Opinion

and

Order

was

adopted

on

the

~7~’

day

of

_______________,

1992,

by

a

vote

of

•7-O

~

~.

Dorothy M. ~nn,

Clerk

Illinois Pollution Control Board

130—455