307.101  Preamble (Renumbered)
307.102  General Requirements (Renumbered)
307.103  Mercury (Renumbered)
307.104  Cyanide (STORET number 00720) (Renumbered)
307.105  Pretreatment Requirements (Repealed)
307.1001  Preamble
307.1002  Definitions
307.1003  Test Procedures for Measurement
307.1005  Toxic Pollutants
307.1006  Electronic Reporting

307.1101  General and Specific Requirements
307.1102  Mercury
307.1103  Cyanide

307.1501  Receiving Stations
307.1502  Fluid Products
307.1503  Cultured Products
307.1504  Butter
307.1505  Cottage Cheese and Cultured Cream Cheese
307.1506  Natural and Processed Cheese
307.1507  Fluid Mix for Ice Cream and Other Frozen Desserts
307.1508  Ice Cream, Frozen Desserts, Novelties, and Other Dairy Desserts
307.1509  Condensed Milk
307.1510  Dry Milk
307.1511  Condensed Whey
307.1512  Dry Whey

307.1601  Corn Wet Milling
307.1602  Corn Dry Milling
307.1603  Normal Wheat Flour Milling
307.1604  Bulgur Wheat Flour Milling
307.1605  Normal Rice Milling
307.1606  Parboiled Rice Milling
307.1607  Animal Feed
307.1608  Hot Cereal
307.1609  Ready-to-Eat Cereal
307.1610  Wheat Starch and Gluten

307.1700  General Provisions
307.1701  Apple Juice
307.1702  Apple Products
307.1703  Citrus Products
307.1704  Frozen Potato Products
307.1705  Dehydrated Potato Products
307.1706  Canned and Preserved Fruits
307.1707  Canned and Preserved Vegetables
307.1708  Canned and Miscellaneous Specialties

307.1801  Farm-Raised Catfish
307.1815  Fish Meal Processing Subcategory (Repealed)

307.1901  Beet Sugar Processing
307.1902  Crystalline Cane Sugar Refining
307.1903  Liquid Cane Sugar Refining

307.2000  General Provisions
307.2001  Wool Scouring
307.2002  Wool Finishing
307.2003  Low Water Use Processing
307.2004  Woven Fabric Finishing
307.2005  Knit Fabric Finishing
307.2006  Carpet Finishing
307.2007  Stock and Yarn Finishing
307.2008  Nonwoven Manufacturing
307.2009  Felted Fabric Processing

307.2101  Nonleaching
307.2102  Leaching
307.2103  Materials Storage Piles Runoff

307.2201  General
307.2202  Ducks

307.2300  General Provisions
307.2301  Electroplating of Common Metals
307.2302  Electroplating of Precious Metals
307.2304  Anodizing
307.2305  Coatings
307.2306  Chemical Etching and Milling
307.2307  Electroless Plating
307.2308  Printed Circuit Boards

307.2400  General Provisions
307.2401  Rayon Fibers
307.2402  Other Fibers
307.2403  Thermoplastic Resins
307.2404  Thermosetting Resins
307.2405  Commodity Organic Chemicals
307.2406  Bulk Organic Chemicals
307.2407  Specialty Organic Chemicals
307.2410  Indirect Discharge Point Sources
307.2490  Non-Complexed Metal-Bearing and Cyanide-Bearing Waste Streams
307.2491  Complexed Metal-Bearing Waste Streams

307.2500  General Provisions
307.2501  Aluminum Chloride Production
307.2502  Aluminum Sulfate Production
307.2503  Calcium Carbide Production
307.2504  Calcium Chloride Production
307.2505  Calcium Oxide Production
307.2506  Chlor-Alkali Process (Chlorine and Sodium or Potassium Hydroxide Production)
307.2508  Hydrofluoric Acid Production
307.2509  Hydrogen Peroxide Production
307.2511  Potassium Metal Production
307.2512  Potassium Dichromate Production
307.2513  Potassium Sulfate Production
307.2514  Sodium Bicarbonate Production
307.2516  Sodium Chloride Production
307.2517  Sodium Dichromate and Sodium Sulfate Production
307.2520  Sodium Sulfite Production
307.2522  Titanium Dioxide Production
307.2523  Aluminum Fluoride Production
307.2524  Ammonium Chloride Production
307.2527  Borax Production
307.2528  Boric Acid Production
307.2529  Bromine Production
307.2530  Calcium Carbonate Production
307.2531  Calcium Hydroxide Production
307.2533  Carbon Monoxide and Byproduct Hydrogen Production
307.2534  Chrome Pigments Production
307.2535  Chromic Acid Production
307.2536  Copper Salts Production
307.2538  Ferric Chloride Production
307.2540  Fluorine Production
307.2541  Hydrogen Production
307.2542  Hydrogen Cyanide Production
307.2543  Iodine Production
307.2544  Lead Monoxide Production
307.2545  Lithium Carbonate Production
307.2547  Nickel Salts Production
307.2549  Oxygen and Nitrogen Production
307.2550  Potassium Chloride Production
307.2551  Potassium Iodide Production
307.2553  Silver Nitrate Production
307.2554  Sodium Bisulfite Production
307.2555  Sodium Fluoride Production
307.2560  Stannic Oxide Production
307.2563  Zinc Sulfate Production
307.2564  Cadmium Pigments and Salts Production
307.2565  Cobalt Salts Production
307.2566  Sodium Chlorate Production
307.2567  Zinc Chloride Production

307.2701  Soap Manufacturing by Batch Kettle
307.2702  Fatty Acid Manufacturing by Fat Splitting
307.2703  Soap Manufacturing by Fatty Acid Neutralization
307.2704  Glycerine Concentration
307.2705  Glycerine Distillation
307.2706  Manufacture of Soap Flakes and Powders
307.2707  Manufacture of Bar Soaps
307.2708  Manufacture of Liquid Soaps
307.2709  Oleum Sulfonation and Sulfation
307.2710  Air-Sulfur Trioxide Sulfation and Sulfonation
307.2711  Sulfur Trioxide Solvent and Vacuum Sulfonation
307.2712  Sulfamic Acid Sulfation
307.2713  Chlorosulfonic Acid Sulfation
307.2714  Neutralization of Sulfuric Acid Esters and Sulfonic Acids
307.2715  Manufacture of Spray-Dried Detergents
307.2716  Manufacture of Liquid Detergents
307.2717  Manufacturing of Detergents by Dry Blending
307.2718  Manufacture of Drum-Dried Detergents
307.2719  Manufacture of Detergent Bars and Cakes

307.2801  Phosphate
307.2802  Ammonia
307.2803  Urea
307.2804  Ammonium Nitrate
307.2805  Nitric Acid
307.2806  Ammonium Sulfate Production
307.2807  Mixed and Blend Fertilizer Production

307.2901  Topping
307.2902  Cracking
307.2903  Petrochemical
307.2904  Lube
307.2905  Integrated

307.3000  General Provisions
307.3001  Cokemaking
307.3002  Sintering
307.3003  Ironmaking
307.3004  Steelmaking
307.3005  Vacuum Degassing
307.3006  Continuous Casting
307.3007  Hot Forming
307.3008  Salt Bath Descaling
307.3009  Acid Pickling
307.3010  Cold Forming
307.3011  Alkaline Cleaning
307.3012  Hot Coating

307.3100  General Provisions
307.3101  Bauxite Refining
307.3102  Primary Aluminum Smelting
307.3103  Secondary Aluminum Smelting
307.3104  Primary Copper Smelting
307.3105  Primary Electrolytic Copper Refining
307.3106  Secondary Copper
307.3107  Primary Lead
307.3108  Primary Zinc
307.3109  Metallurgical Acid Plants
307.3110  Primary Tungsten
307.3111  Primary Columbium-Tantalum
307.3112  Secondary Silver
307.3113  Secondary Lead
307.3114  Primary Antimony
307.3115  Primary Beryllium
307.3116  Primary and Secondary Germanium and Gallium
307.3117  Secondary Indium
307.3118  Secondary Mercury
307.3119  Primary Molybdenum and Rhenium
307.3120  Secondary Molybdenum and Vanadium
307.3121  Primary Nickel and Cobalt
307.3122  Secondary Nickel
307.3123  Primary Precious Metals and Mercury
307.3124  Secondary Precious Metals
307.3125  Primary Rare Earth Metals
307.3126  Secondary Tantalum
307.3127  Secondary Tin
307.3128  Primary and Secondary Titanium
307.3129  Secondary Tungsten and Cobalt
307.3130  Secondary Uranium
307.3131  Primary Zirconium and Hafnium

307.3301  Steam Electric Power Generating

307.3401  Open Electric Furnaces With Wet Air Pollution Control Devices
307.3402  Covered Electric Furnaces and Other Smelting Operations with Wet Air Pollution Control Devices
307.3403  Slag Processing
307.3404  Covered Calcium Carbide Furnaces With Wet Air Pollution Control Devices
307.3405  Other Calcium Carbide Furnaces
307.3406  Electrolytic Manganese Products
307.3407  Electrolytic Chromium

307.3500  General Provisions
307.3501  Hair Pulp, Chrome Tan, Retan-Wet Finish
307.3502  Hair Save, Chrome Tan, Retan-Wet Finish
307.3503  Hair Save or Pulp, Non-Chrome Tan, Retan-Wet Finish
307.3504  Retan-Wet Finish-Sides
307.3505  No Beamhouse
307.3506  Through-the-Blue
307.3507  Shearling
307.3508  Pigskin
307.3509  Retan-Wet Finish-Splits
307.3590  Potassium Ferricyanide Titration Method

307.3601  Insulation Fiberglass
307.3602  Sheet Glass Manufacturing
307.3603  Rolled Glass Manufacturing
307.3604  Plate Glass Manufacturing
307.3605  Float Glass Manufacturing
307.3606  Automotive Glass Tempering
307.3607  Automotive Glass Laminating
307.3608  Glass Container Manufacturing
307.3610  Glass Tubing (Danner) Manufacturing
307.3611  Television Picture Tube Envelope Manufacturing
307.3612  Incandescent Lamp Envelope Manufacturing
307.3613  Hand Pressed and Blown Glass Manufacturing

307.3701  Asbestos-Cement Pipe
307.3702  Asbestos-Cement Sheet
307.3703  Asbestos Paper (Starch Binder)
307.3704  Asbestos Paper (Elastomeric Binder)
307.3705  Asbestos Millboard
307.3706  Asbestos Roofing
307.3707  Asbestos Floor Tile
307.3708  Coating or Finishing of Asbestos Textiles
307.3709  Solvent Recovery
307.3710  Vapor Absorption
307.3711  Wet Dust Collection

307.3801  Tire and Inner Tube Plants
307.3802  Emulsion Crumb Rubber
307.3803  Solution Crumb Rubber
307.3804  Latex Rubber
307.3805  Small-Sized General Molded, Extruded, and Fabricated Rubber Plants
307.3806  Medium-Sized General Molded, Extruded, and Fabricated Rubber Plants
307.3807  Large-Sized General Molded, Extruded, and Fabricated Rubber Plants
307.3808  Wet Digestion Reclaimed Rubber
307.3809  Pan, Dry Digestion, and Mechanical Reclaimed Rubber
307.3810  Latex-Dipped, Latex-Extruded, and Latex-Molded Rubber
307.3811  Latex Foam

307.3900  General Provisions
307.3901  Barking
307.3902  Veneer
307.3903  Plywood
307.3904  Dry Process Hardboard
307.3905  Wet Process Hardboard
307.3906  Wood Preserving—Waterborne or Non-pressure
307.3907  Wood Preserving—Steam
307.3908  Wood Preserving—Boulton
307.3909  Wet Storage
307.3910  Log Washing
307.3911  Sawmills and Planing Mills
307.3912  Finishing
307.3913  Particleboard Manufacturing
307.3914  Insulation Board
307.3915  Wood Furniture and Fixture Production without Water Wash Spray Booths or without Laundry Facilities
307.3916  Wood Furniture and Fixture Production with Water Wash Spray Booths or with Laundry Facilities

307.4000  General Provisions
307.4001  Dissolving Kraft
307.4002  Bleached Papergrade Kraft and Soda
307.4003  Unbleached Kraft
307.4004  Dissolving Sulfite
307.4005  Papergrade Sulfite
307.4006  Semi-Chemical
307.4007  Mechanical Pulp
307.4008  Non-Wood Chemical Pulp
307.4009  Secondary Fiber Deink
307.4010  Secondary Fiber Non-Deink
307.4011  Fine and Lightweight Papers from Purchased Pulp
307.4012  Tissue, Filter, Non-Woven, and Paperboard from Purchased Pulp
307.4013  Groundwood-Thermo-Mechanical (Repealed)
307.4014  Groundwood-CMN Papers (Repealed)
307.4015  Groundwood-Fine Papers (Repealed)
307.4016  Soda (Repealed)
307.4017  Deink (Repealed)
307.4018  Nonintegrated-Fine Papers (Repealed)
307.4019  Nonintegrated-Tissue Papers (Repealed)
307.4020  Tissue From Wastepaper (Repealed)
307.4021  Papergrade Sulfite (Drum Wash) (Repealed)
307.4022  Unbleached Kraft and Semi-Chemical (Repealed)
307.4023  Wastepaper-Molded Products (Repealed)
307.4024  Nonintegrated-Lightweight Papers (Repealed)
307.4025  Nonintegrated-Filter and Nonwoven Papers (Repealed)
307.4026  Nonintegrated-Paperboard (Repealed)

307.4101  Builder's Paper and Roofing Felt (Repealed)

307.4201  Simple Slaughterhouse
307.4202  Complex Slaughterhouse
307.4203  Low-Processing Packinghouse
307.4204  High-Processing Packinghouse
307.4205  Small Processor
307.4206  Meat Cutter
307.4207  Sausage and Luncheon Meats Processor
307.4208  Ham Processor
307.4209  Canned Meats Processor
307.4210  Renderer

307.4300  General Provisions
307.4301  Metal Finishing

307.4503  Onshore Facility Standards
307.4508  Coalbed Methane Subcategory

307.4700  General Provisions
307.4701  Metals Treatment and Recovery
307.4702  Oils Treatment and Recovery
307.4703  Organics Treatment and Recovery
307.4704  Multiple Waste Streams

307.4900  General Provisions
307.4901  Fermentation Products
307.4902  Extraction Products
307.4903  Chemical Synthesis Products
307.4904  Mixing/Compounding and Formulation
307.4905  Research (Repealed)

307.5100  Dental Offices

307.5200  General Provisions
307.5201  Tank Trucks and Intermodal Tank Containers Transporting Chemical and Petroleum Cargos
307.5202  Rail Tank Cars Transporting Chemical and Petroleum Cargos
307.5203  Tank Barges and Ocean/Sea Tankers Transporting Chemical and Petroleum Cargos
307.5204  Tanks Transporting Food Grade Cargos

307.5301  Asphalt Emulsion
307.5302  Asphalt Concrete
307.5303  Asphalt Roofing
307.5304  Linoleum and Printed Asphalt Felt

307.5401  Commercial Hazardous Waste Combustor

307.5500  General Provisions
307.5501  RCRA Subtitle C Hazardous Waste Landfill
307.5502  RCRA Subtitle D Non-Hazardous Waste Landfill

307.5601  Oil-Base Solvent Wash Paint

307.5701  Oil-Base Solvent Wash Ink

307.6500  General Provisions
307.6501  Organic Pesticide Chemicals Manufacturing
307.6502  Metallo-Organic Pesticides Chemicals Manufacturing
307.6503  Pesticide Chemicals Formulating and Packaging
307.6505  Repackaging of Agricultural Pesticides Performed at Refilling Establishments

307.6801  Carbon Black Furnace Process
307.6802  Carbon Black Thermal Process
307.6803  Carbon Black Channel Process
307.6804  Carbon Black Lamp Process

307.7100  General Provisions
307.7101  Cadmium
307.7102  Calcium
307.7103  Lead
307.7104  Leclanche
307.7105  Lithium
307.7106  Magnesium
307.7107  Zinc

307.7300  General Provisions
307.7301  Contact Cooling and Heating Water
307.7302  Cleaning Water
307.7303  Finishing Water

307.7400  General Provisions
307.7401  Aluminum Casting
307.7402  Copper Casting
307.7403  Ferrous Casting
307.7404  Zinc Casting

307.7500  General Provisions
307.7501  Steel Basis Material
307.7502  Galvanized Basis Material
307.7503  Aluminum Basis Material
307.7504  Canmaking

307.7600  General Provisions
307.7601  Steel Basis Material
307.7602  Cast Iron Basis Material
307.7603  Aluminum Basis Material
307.7604  Copper Basis Material

307.7700  General Provisions
307.7701  Rolling With Neat Oils
307.7702  Rolling With Emulsions
307.7703  Extrusion
307.7704  Forging
307.7705  Drawing With Neat Oils
307.7706  Drawing With Emulsions or Soaps

307.7800  General Provisions
307.7801  Copper Forming
307.7802  Beryllium Copper Forming

307.7901  Semiconductor
307.7902  Electronic Crystals
307.7903  Cathode Ray Tube
307.7904  Luminescent Materials

307.8100  General Provisions
307.8101  Lead-Tin-Bismuth Forming
307.8102  Magnesium Forming
307.8103  Nickel-Cobalt Forming
307.8104  Precious Metals Forming
307.8105  Refractory Metals Forming
307.8106  Titanium Forming
307.8107  Uranium Forming
307.8108  Zinc Forming
307.8109  Zirconium-Hafnium Forming
307.8110  Metal Powders

a)  This Part places certain restrictions on the types, concentrations, and quantities of contaminants that can be discharged into sewer systems in the State.

1)  Subpart B includes standards for the discharge of contaminants to sewer systems. These apply to dischargers to publicly owned treatment works (POTWs) and to dischargers to other types of treatment works, as specified in each Section.

2)  Subparts F through CT include standards for the discharge of contaminants from certain industrial source categories into POTWs.

b)  35 Ill. Adm. Code 310 specifies requirements for pretreatment programs for POTWs.

c)  This Part incorporates federal regulations by reference.

1)  The incorporations include no later amendments or editions.

2)  Except where the contrary is clearly indicated, the Board intends to set forth all procedural requirements in full in this Part and 35 Ill. Adm. Code 310 and to use only the definitions, requirements, or standards from the incorporated material.

3)  Except where the contrary is clearly indicated, references to other federal regulations within incorporated material are to be construed as referencing Board rules derived from the referenced material rather than referencing the other federal regulation.

a)  The definitions of 35 Ill. Adm. Code 301 do not apply to this Part.
 
b)  The definitions of 35 Ill. Adm. Code 310 apply to this Part.

Section 307.1005  Toxic Pollutants

a)  The Board incorporates by reference 40 CFR 401.15 (2005). This incorporation includes no later amendments or editions.

b)  A “toxic pollutant” is one of the materials listed in 40 CFR 401.15 or in table II or III in appendix D to 40 CFR 122, incorporated by reference in 35 Ill. Adm. Code 310.107.

SUBPART B: GENERAL AND SPECIFIC PRETREATMENT REQUIREMENTS

 

a)  General Requirements

1)  Pollutants that pass through the POTW; or

2)  Pollutants that interfere with the operation or performance of the POTW.

b)  Specific Requirements

1)  Pollutants that create a fire or explosion hazard within the POTW, including, but not limited to, waste streams with a closed cup flashpoint of less than 60 °C (140 °F) using the test methods specified in 35 Ill. Adm. Code 721.121;

2)  Pollutants that would cause safety hazards to the personnel operating the treatment works;

3)  Pollutants that will cause corrosive damage to the POTW;

4)  Pollutants that would be injurious in any other way to sewers, treatment works, or structures;

5)  Discharges with a pH less than 5.0, unless the POTW is specifically designed to accommodate such discharges;

6)  Solid or viscous pollutants in amounts that will obstruct the flow in the POTW resulting in interference;

7)  Any pollutant, including oxygen-demanding pollutants, at a flow rate or concentration that will cause interference with the POTW;

8)  Heat in amounts that will inhibit biological activity in the POTW and interfere with the POTW;

9)  Heat in amounts that result in temperatures in the influent to the POTW treatment plant greater than 40 ºC (104 ºF), unless the Agency approves alternate temperature limits in the pretreatment plan;

10)  Pollutants that would cause the effluent from the treatment works to violate applicable effluent standards;

11)  Petroleum oil, non-biodegradable cutting oil, or products of mineral oil origin in amounts that will cause interference or pass through;

12)  Pollutants that result in the presence of toxic gases, vapors, or fumes within the POTW in a quantity that may cause acute worker health and safety problems; or

13)  Any trucked or hauled pollutants, except at discharge points designated by the POTW.

a)  Except as provided in this Section, no person may cause or allow the concentration of mercury in any discharge to a publicly owned or publicly regulated sewer system to exceed 0.0005 mg/L, subject to the averaging rule contained in 35 Ill. Adm. Code 304.104(a).

b)  Subsection (a) does not apply if the discharge is to a publicly owned or publicly regulated sewer system that is required to meet a limitation less stringent than the 0.0005 mg/L mercury concentration, in which case the discharge limitation must be the same as that applicable to the publicly owned or regulated sewer system to which it discharges.

c)  Subsection (a) does not apply if all the following conditions are met:

1)  The discharger does not use mercury, the discharger uses mercury and this use cannot be eliminated, or the discharger uses mercury only in chemical analysis or in laboratory or other equipment and takes reasonable care to avoid contamination of wastewater;

2)  The discharge's mercury concentration is less than 0.003 mg/L, as determined by applying the averaging rules of 35 Ill. Adm. Code 304.104(a);

3)  The discharger is providing the best degree of treatment consistent with technological feasibility, economic reasonableness, and sound engineering judgment. This may include no treatment for mercury; and

4)  The discharger has an inspection and maintenance program likely to reduce or prevent an increase in the level of mercury discharges.

d)  The discharge of wastes from medicinal or therapeutic use of mercury, exclusive of laboratory use, will be exempt from the limitations of subsection (a) if all the following conditions are met:

1)  The total plant discharge is less than 227 g (one-half pound) as Hg in any year;

2)  This discharge is to a public sewer system; and

3)  The discharge does not, alone or in conjunction with other sources, cause the effluent from the sewer system or treatment plant to exceed 0.0005 mg/L of mercury.

e)  No person may cause or allow any discharge of mercury to a publicly owned or publicly regulated sewer system that, alone or in combination with other sources, causes the sewer treatment plant discharge to violate the water quality standard of 35 Ill. Adm. Code 302 for mercury applicable in the receiving stream.

f)  For purposes of permit issuance, the Agency may consider applying the exception under subsection (b) or (c) to determine compliance with this Section. The Agency may impose permit conditions necessary or required to assure continued application of the exception. When subsection (b) or (c) applies, the Agency may impose an effluent limitation in the permit that allows the discharge of a concentration of mercury greater than 0.0005 mg/L but not more than 0.003 mg/L.

g)  The mercury standards of Section 307.1102 will not apply to the Reilly Industries, Inc., Granite City, which discharges to any publicly-owned treatment works that receives such a manufacturing facility's wastewater. The amount of mercury discharged by any such manufacturing facility must not exceed a monthly average of 0.025 mg/L nor a maximum of 0.035 mg/L or 7.5 grams per day, subject to the Board's averaging rules during any one day.

a)  Waste to any public sewer system must not contain more than 10 mg/L total cyanide, and any sample tested must not release more than 2 mg/L of cyanide when tested at a pH of 4.5 and a temperature of 66 ºC (150 ºF) for 30 minutes, except as permitted by subsection (b).

b)  Upon application by a county, municipality, sanitary district, or public utility and approval by the Agency, based upon the Agency's determination that no violation of the effluent standards of 35 Ill. Adm. Code 304 or hazard to workers in that sewage works will result, limited additional amounts of cyanide exceeding the standards in subsection (a) may be discharged to the sewage works of that county, sanitary district, municipality, or public utility.

c)  Nothing in this Section may be construed as limiting the authority of any county, municipality, sanitary district, or public utility to impose any more stringent standards or limitations on cyanide discharges to its sewage works.

d)  Any actions undertaken under subsection (b) will be subject to the limitations of Section 307.2400(b)(7).

a)  Applicability. This Section applies to discharges resulting from the operation of receiving stations engaged in the assembly and reshipment of bulk milk for the use of manufacturing or processing plants.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of market milk (ranging from 3.5 percent fat to fat-free), flavored milk (chocolate and others), and cream (of various fat concentrations, plain, and whipped).

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of cultured products, including cultured skim milk (cultured buttermilk), yogurt, sour cream, and dips of various types.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  “New source” means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of butter, either by churning or continuous process.

b)  Specialized definitions. The Board incorporates by reference 40 CFR 405.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing sources.

1)  The Board incorporates by reference 40 CFR 405.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) of this Section may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of such standards.

d)  New sources.

1)  The Board incorporates by reference 40 CFR 405.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) of this Section may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of such standards.

3)  “New source” means any building, structure, facility, or installation the construction of which commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of butter, either by churning or continuous process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of cottage cheese and cultured cream cheese.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of natural cheese (hard curd) and processed cheese.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of fluid mixes for ice cream and other frozen desserts for later freezing in other plants; it does not include freezing of the products as one of the affected operations.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.71 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.74 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of ice cream, ice milk, sherbet, water ices, stick confections, frozen novelties products, frozen desserts, mellorine, pudding, and other dairy product base desserts. If fluid mixes prepared at another plant are employed, the appropriate values from Section 307.1507 should be deducted from the limitations.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.81 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.84 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of condensed whole milk, condensed skim milk, sweetened condensed milk, and condensed buttermilk.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.91 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.94 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.96 (2003). This incorporation includes no later amendments or editions.

2  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of dry whole milk, dry skim milk, and dry buttermilk.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.101 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources
 
1)  The Board incorporates by reference 40 CFR 405.104 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.106 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of condensed sweet whey and condensed acid whey.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.111 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.114 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.116 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacture of sweet or acid dry whey.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 405.121 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 405.124 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 405.126 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 20, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which shelled corn is steeped in a dilute solution of sulfurous acid and then processed by wet means into such products as animal feed, regular and modified starches, corn oil, corn syrup, and dextrose.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which shelled corn is washed and subsequently milled by dry processes into such products as cornmeal, grits, flour, oil, and animal feed. This Section does not apply to discharges from subsequent manufacturing operations to produce expanded or extruded feed or feed products.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the processes in which wheat and other grains are milled by dry processes into flour and millfeed.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which wheat is parboiled, dried, and partially debranned in the production of bulgur.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which rice is cleaned and milled by dry processes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which rice is cleaned, cooked, and dried before being milled.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 406.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 4, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacturing of animal feeds (formula feed concentrate) using primarily grain and grain by-products that may be supplemented by proteins, pharmaceuticals, vitamins, or mineral additives.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.71 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 17, 1974.

a)  Applicability. This Section applies to discharges resulting from the production of various breakfast cereals from grains, principally wheat and oats, requiring cooking before normal human consumption.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.81 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 17, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of various grains and other materials (whole grain wheat, rice, corn grits, oat flour, sugar, and minor ingredients) to produce various breakfast cereals normally available for human consumption without cooking.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.91 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.96 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 17, 1974.

a)  Applicability. This Section applies to discharges resulting from those industrial operations using wheat flour as a raw material for the production of wheat starch and gluten (protein) components through conventional processes of physical separation and subsequent refinement.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 406.101 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 406.106 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 17, 1974.

Section 307.1700  General Provisions

a)  Applicability. This Section applies to discharges resulting from the processing of apples into apple juice or apple cider.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after November 9, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of apples into apple products. The processing of apples into caustic-peeled or dehydrated products is specifically excluded.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after November 9, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of citrus into citrus products.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after November 9, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of white potatoes into frozen potato products.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after November 9, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of white potatoes into dehydrated potato products.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after November 9, 1974.

a)  Applicability. This Section applies to discharges resulting from the processing of the following fruit products: apricots; caneberries; sweet, sour, and brined cherries; cranberries; dried fruit; grape juice canning and pressing; olives; peaches; pears; fresh and processed pickles and pickle salting stations; pineapples; plums; raisins; strawberries; and tomatoes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 21, 1975.

a)  Applicability. This Section applies to discharges resulting from the processing of the following vegetable products: beets, broccoli, carrots, canned and frozen corn, dehydrated onions and garlic, dehydrated vegetables, dry beans, lima beans, mushrooms, canned onions, peas, sauerkraut canning and cutting, snap beans, spinach, squash, and canned potatoes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.71 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.74 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 21, 1975.

a)  Applicability. This Section applies to discharges resulting from the processing of the following specialty products: added ingredients; baby food; corn, potato, and tortilla chips; ethnic foods; jams and jellies; mayonnaise and dressings; soups; and tomato-starch-cheese canned specialties.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 407.81 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 407.84 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 407.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 21, 1975.

a)  Applicability. This Section applies to discharges resulting from the processing of farm-raised catfish by existing facilities that process more than 1,362 kg (3,000 lb) of raw material per day on any day during a calendar year and all new sources.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 408.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 408.l4 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 408.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after February 6, 1974.

a)  Applicability. This Section applies to discharges resulting from any operation attendant to the processing of sugar beets for the production of sugar.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 409.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 409.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 409.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after August 22, 1973.

a)  Applicability. This Section applies to discharges resulting from the processing of raw cane sugar into crystalline refined sugar.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 409.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 409.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 409.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 7, 1973.

a)  Applicability. This Section applies to discharges resulting from the processing of raw cane sugar into liquid refined sugar.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 409.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 409.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 409.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 7, 1973.

SUBPART K: TEXTILE MILLS

 

Section 307.2000  General Provisions

a)  Applicability. This Subpart K applies to any textile mill or textile processing facility that introduces or may introduce process wastewater pollutants into a POTW.

b)  General definitions. The Board incorporates by reference 40 CFR 410.01 (2003). This incorporation includes no later amendments or editions.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: wool scouring, topmaking, and general cleaning of raw wool.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: wool finishers, including carbonizing, fulling, dyeing, bleaching, rinsing, fireproofing, and other similar processes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.21. This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: yarn manufacture, yarn texturizing, unfinished fabric manufacture, fabric coating, fabric laminating, tire cord and fabric dipping, and carpet tufting and carpet backing. Rubberized or rubber-coated fabrics regulated by 40 CFR 428 are specifically excluded.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.31 (2005). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.34 (2005). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.36 (2005). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: woven fabric finishers, which may include any or all of the following unit operations: desizing, bleaching, mercerizing, dyeing, printing, resin treatment, waterproofing, flameproofing, soil repellency application, and a special finish application.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: knit fabric finishers, which may include any or all of the following unit operations: bleaching, mercerizing, dyeing, printing, resin treatment, waterproofing, flameproofing, soil repellency application, and a special finish application.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: carpet mills, which may include any or all of the following unit operations: bleaching, scouring, carbonizing, fulling, dyeing, printing, resin treatment, waterproofing, flameproofing, soil repellency, looping, and backing with foamed and unfoamed latex and jute. Carpet backing without other carpet manufacturing operations is included in Section 307.2003.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 410.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the following types of textile mills: stock or yarn dyeing or finishing, which may include any or all of the following unit operations and processes: cleaning, scouring, bleaching, mercerizing, dyeing, and special finishing.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.74 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from facilities that primarily manufacture nonwoven textile products of wool, cotton, or synthetics, singly or as blends, by mechanical, thermal, or adhesive bonding procedures. Nonwoven products produced by fulling and felting processes are covered in Section 307.2009.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.84 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from facilities that primarily manufacture nonwoven products by employing fulling and felting operations as a means of achieving fiber bonding.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 410.94 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 410.96 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 10, 1979.

a)  Applicability. This Section applies to discharges resulting from the process in which several mineral ingredients (limestone or other natural sources of calcium carbonate, silica, alumina, and iron together with gypsum) are used in the manufacturing of cement and in which kiln dust is not contacted with water as an integral part of the process and water is not used in wet scrubbers to control kiln stack emissions.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 411.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 411.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 411.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 7, 1973.

a)  Applicability. This Section applies to discharges resulting from the process in which several mineral ingredients (limestone or other natural sources of calcium carbonate, silica, alumina, and iron together with gypsum) are used in the manufacturing of cement and in which kiln dust is contacted with water as an integral part of the process or water is used in wet scrubbers to control kiln stack emissions.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 411.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources
 
1)  The Board incorporates by reference 40 CFR 411.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 411.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 7, 1973.

a)  Applicability. This Section applies to discharges resulting from the runoff of rainfall that derives from the storage of materials including raw materials, intermediate products, finished products, and waste materials that are used in or derived from the manufacture of cement under either Section 307.2101 or 307.2102.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 411.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 411.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 411.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 7, 1973.

a)  Applicability. This Section applies to manure, litter, or process wastewater discharges resulting from concentrated animal feeding operations (CAFOs). Manufacturing or agricultural activities that may be subject to this Section are generally reported under one or more of the following SIC codes, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107:

1)  SIC Code 0211 (Beef Cattle Feedlots);

2)  SIC Code 0213 (Hogs);

3)  SIC Code 0214 (Sheep and Goats);

4)  SIC Code 0241 (Dairy Farms);

5)  SIC Code 0251 (Broiler, Fryer, and Roaster Chickens);

6)  SIC Code 0252 (Chicken Eggs);

7)  SIC Code 0253 (Turkeys and Turkey Eggs);

8)  SIC Code 0254 (Poultry Hatcheries);

9)  SIC Code 0259 (Poultry and Eggs, Not Elsewhere Classified); or

10)  SIC Code 0272 (Horses and Other Equines).

b)  General definitions. The Board incorporates by reference 40 CFR 412.2 (2011). This incorporation includes no later amendments or editions.

c)  General pretreatment standards. The Board incorporates by reference 40 CFR 412.3 (2011). This incorporation includes no later amendments or editions.

d)  A facility is determined a concentrated animal feeding operation (CAFO) according to the definitions and requirements of 40 CFR 122.23(b) and (c), incorporated by reference in 35 Ill. Adm. Code 310.107.

a)  Applicability. This Section applies to discharges resulting from the production areas at dry lot and wet lot duck CAFOs. This Section does not apply to such a CAFO with less than the following capacity: 5,000 ducks.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 412.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. USEPA removed the former standards applicable to existing sources at 68 Fed. Reg. 7176 (February 12, 2003).

d)  New Sources

1)  The Board incorporates by reference 40 CFR 412.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after September 7, 1973.

a)  Applicability

1)  This Subpart N applies to any electroplating operations in which metal is electroplated on any basis material and to related metal finishing operations as identified in the various Sections, whether such operations are conducted in conjunction with electroplating, independently, or as part of some other operation.

2)  Operations similar to electroplating that are specifically excepted from coverage of this Subpart N include the following:

A)  Electrowinning and electrorefining conducted as a part of nonferrous metal smelting and refining (Subpart V);

B)  Metal surface preparation and conversion coating conducted as a part of coil coating (Subpart CN);

C)  Metal surface preparation and immersion plating or electroless plating conducted as a part of porcelain enameling (Subpart CO); and

D)  Electrodeposition of active electrode materials, electroimpregnation, and electroforming conducted as a part of battery manufacturing (Subpart CJ).

3)  Metallic platemaking and gravure cylinder preparation conducted within or for printing and publishing facilities, and continuous strip electroplating conducted within iron and steel manufacturing facilities are exempted from the pretreatment standards for existing sources in this Subpart N.

4)  Certain electroplating operations may be subject to the metal finishing standards of Subpart BH.

b)  General Definitions. The Board incorporates by reference 40 CFR 413.02 (2003). This incorporation includes no later amendments or editions.

c)  Monitoring Requirements. The Board incorporates by reference 40 CFR 413.03 (2003). This incorporation includes no later amendments or editions.

d)  Compliance Dates. The Board incorporates by reference 40 CFR 413.01(a) (2003). This incorporation includes no later amendments or editions.

e)  Integrated Facilities. The Board incorporates by reference 40 CFR 413.04 (2003). This incorporation includes no later amendments or editions.

a)  Applicability. This Section applies to discharges resulting from the process in which a ferrous or nonferrous basis material is electroplated with copper, nickel, chromium, zinc, tin, lead, cadmium, iron, aluminum, or any combination of these.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the process in which a ferrous or nonferrous basis material is plated with gold, silver, iridium, palladium, platinum, rhodium, ruthenium, or any combination of these.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of such standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the anodizing of ferrous or nonferrous materials.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the chromating, phosphating, or immersion plating on ferrous or nonferrous materials.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the chemical milling or etching of ferrous or nonferrous materials.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the electroless plating of a metallic layer on a metallic or nonmetallic substrate.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.71 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.74 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  Applicability. This Section applies to discharges resulting from the manufacture of printed circuit boards, including all manufacturing operations required or used to convert an insulating substrate to a finished printed circuit board. The other Sections of this Subpart N do not apply to the manufacture of printed circuit boards.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 413.81 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 413.84 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  Sources whose construction commenced after August 31, 1982 are subject to Subpart BH.

a)  General Definitions. The Board incorporates by reference 40 CFR 414.10 (2005). This incorporation includes no later amendments or editions.
 
b)  Applicability
 
1)  This Subpart O applies to process wastewater discharges from all establishments or portions of establishments that manufacture the organic chemicals, plastics, and synthetic fibers (OCPSF) products or product groups that are covered by Sections 307.2402 through 307.2408 and which are included in the following SIC major groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107:
 
A)  SIC 2821: Plastic materials, synthetic resins, and nonvulcanizable elastomers.

B)  SIC 2823: Cellulosic man-made fibers.

C)  SIC 2824: Synthetic organic fibers, except cellulosic.

D)  SIC 2865: Cyclic crudes and intermediates, dyes, and organic pigments.

E)  SIC 2869: Industrial organic chemicals, not elsewhere classified.
 
2)  This Subpart O applies to wastewater discharges from OCPSF research and development, pilot plant, technical service, and laboratory bench-scale operations if such operations are conducted in conjunction with and related to existing OCPSF manufacturing activities at the plant site.

3)  Notwithstanding subsection (b)(1), this Subpart O does not apply to discharges resulting from the manufacture of OCPSF products if the products are included in the following SIC subgroups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, and if the products have in the past been reported by the establishment under these subgroups and not under the SIC groups listed in subsection (b)(1):
 
A)  SIC 2843085: Bulk surface active agents.

B)  SIC 28914: Synthetic resin and rubber adhesives.

C)  Chemicals and Chemical Preparations Not Elsewhere Classified:

i)  SIC 2899568: Sizes, all types.

ii)  SIC 2899597: Other industrial chemical specialties, including fluxes, plastic wood preparations, and embalming fluids.
 
D)  SIC 2911058: Aromatic hydrocarbons manufactured from purchased refinery products.
 
E)  SIC 2911632: Aliphatic hydrocarbons manufactured from purchased refinery products.
 
4)  Notwithstanding subsection (b)(1), this Subpart O does not apply to any discharges for which a different set of previously promulgated standards in this Part apply, unless the facility reports OCPSF products under SIC codes 2865, 2869, or 2821, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, and the facility's OCPSF wastewaters are discharged separately to a POTW.

5)  This Subpart O does not apply to any process wastewater discharge from the manufacture of organic chemical compounds solely by extraction from plant and animal raw materials or by fermentation processes.
 
6)  Discharges of chromium, copper, lead, nickel, and zinc in “complexed metal-bearing waste streams,” listed in Section 307.2491, are not subject to this Subpart O.

7)  Non-Amenable Cyanide
 
A)  Discharges of cyanide in “cyanide-bearing waste streams,” listed in Section 307.2490, are not subject to the cyanide limitations of this Subpart O if both of the following occur:
 
i)  The Control Authority determines that the cyanide limitations are not achievable due to elevated levels of non-amenable cyanide (i.e., cyanide that is not oxidized by chlorine treatment) that result from the unavoidable complexing of cyanide at the process source of the cyanide-bearing waste stream, and
 
ii)  The control authority establishes an alternative total cyanide or amenable cyanide limitation that reflects the best available technology economically achievable.
 
B)  The control authority must base its determination made pursuant to subsection (b)(7)(A) on a review of the relevant engineering, production, and sampling and analytical information at its disposal, including measurements of both total and amenable cyanide in the waste stream.
 
C)  The control authority must set forth its determination made pursuant to subsection (b)(7)(A) in a written analysis of the extent of complexing in the waste stream and its impact on cyanide treatability, based on the information at its disposal.

D)  Alternative cyanide discharge limitation determinations made pursuant to this subsection (b)(7) are subject to the limitations of Section 307.1103. However, Section 307.1103 may not be used to allow a discharge of total cyanide greater than that otherwise allowed by this subsection (b)(7).
 
8)  Allowances for Non-Metal-Bearing Waste Streams
 
A)  The control authority must establish discharge limitations for lead and zinc for waste streams not listed in Section 307.2490 and not otherwise determined to be “metal-bearing waste streams” if it determines that the wastewater metals contamination is due to background levels that are not reasonably avoidable, from such sources as intake water, corrosion of materials of construction, or contamination of raw materials.
 
B)  The control authority must base its determination made pursuant to subsection (b)(8)(A) on a review of relevant plant operating conditions, process chemistry, engineering, and sampling and analytical information.
 
C)  The control authority must set forth its determination made pursuant to subsection (b)(8)(A) in a written analysis of the sources and levels of the metals, based on the information at its disposal.
 
D)  The control authority may establish limitations for lead and zinc for non-metal-bearing waste streams for the purposes of subsection (b)(8)(A) between the following levels:
 
i)  The lowest level that the control authority determines, based on best professional judgment, can be reliably measured; and
 
ii)  The concentration of such metals present in the waste streams, but not to exceed the applicable limitations contained in Sections 307.2401 through 307.2407.

iii)  For zinc, the applicable limitations that the discharge must not exceed are those appearing in the tables in Sections 307.2401 through 307.2407, not the alternative limitations for rayon fiber manufacture by the viscose process, as set forth in footnote 2 to the table in 40 CFR 414.25, incorporated by reference at Section 307.2401(c)(1), or the alternative limitations for acrylic fiber manufacture by the zinc chloride/solvent process, as set forth in footnote 2 to the table in 40 CFR 414.35, each incorporated by reference at Section 307.2402(c)(1).
 
E)  The limitations for individual dischargers must be set on a mass basis, by multiplying the concentration allowance established by the control authority times the process wastewater flow from the individual waste streams in which incidental metals are present.
 
c)  Compliance Date. All dischargers subject to a pretreatment standard for existing sources in this Subpart O must have complied with the standard by November 5, 1990.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of rayon fiber by the viscose process only.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.25 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of the products classified under SIC 2823, cellulosic man-made fibers and fiber groups, except rayon, and under SIC 2824, synthetic organic fibers and fiber groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, listed in this subsection. Product groups are indicated with an asterisk (*).

*Acrylic fibers (85% Polyacrylonitrile)
*Cellulose acetate fibers
*Fluorocarbon (Teflon) fibers
*Modacrylic fibers
*Nylon 6 fibers
Nylon 6 monofilament
*Nylon 66 fibers
Nylon 66 monofilament
*Polyamide fibers (Quiana)
*Polyaramid (Kevlar) resin-fibers
*Polyaramid (Nomex) resin-fibers
*Polyester fibers
*Polyethylene fibers
*Polypropylene fibers
*Polyurethane fibers (Spandex)

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.35 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of the products classified under SIC 28213, thermoplastic resins and thermoplastic resin groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, listed in this subsection. Product groups are indicated with an asterisk (*).

*Abietic acid-derivatives
*ABS resins
*ABS-SAN resins
*Acrylate-methacrylate latexes
*Acrylic latex
*Acrylic resins
*Cellulose acetate butyrates
Cellulose acetate resin
*Cellulose acetates
*Cellulose acetates priopionates
Cellulose nitrate
*Ethylene-methacrylic acid copolymers
*Ethylene-vinyl acetate copolymers
*Fatty acid resins
*Fluorocarbon polymers
Nylon 11 resin
*Nylon 6-66 copolymers
*Nylon 6-Nylon 11 blends
Nylon 6 resin
Nylon 612 resin
Nylon 66 resin
*Nylons
*Petroleum hydrocarbon resins
*Polyvinyl pyrrolidone-copolymers
*Poly(alpha)olefins
Polyacrylic acid
*Polyamides
*Polyarylamides
*Polybutadiene
*Polybutenes
Polybutyl succinic anhydride
*Polycarbonates
*Polyester resins
*Polyester resins, Polybutylene terephthalate
*Polyester resins, Polyoxybenzoate
Polyethylene
*Polyethylene-ethyl acrylate resins
*Polyethylene-polyvinyl acetate copolymers
Polyethylene resin (HDPE)
Polyethylene resin (LDPE)
Polyethylene resin, scrap
Polyethylene resin, wax (low molecular weight)
Polyethylene resin, latex
Polyethylene resins
*Polyethylene resins, compounded
*Polyethylene, chlorinated
*Polyimides
*Polypropylene resins
Polystyrene (crystal)
Polystyrene (crystal) modified
*Polystyrene--copolymers
*Polystyrene-acrylic latexes
Polystyrene impact resins
Polystyrene latex
Polystyrene, expandable
Polystyrene, expanded
*Polysulfone resins
Polyvinyl acetate
*Polyvinyl acetate-PVC copolymers
*Polyvinyl acetate copolymers
*Polyvinyl acetate resins
Polyvinyl alcohol resin
Polyvinyl chloride
Polyvinyl chloride, chlorinated
*Polyvinyl ether-maleic anhydride
*Polyvinyl formal resins
*Polyvinylacetate-methacrylic copolymers
*Polyvinylacetate acrylic copolymers
*Polyvinylacetate-2-ethylhexylacrylate copolymers
Polyvinylidene chloride
*Polyvinylidene chloride copolymers
*Polyvinylidene-vinyl chloride resins
*PVC copolymers, acrylates (Latex)
*PVC copolymers, ethylene-vinyl chloride
*Rosin derivative resins
*Rosin modified resins
*Rosin resins
*SAN resins
*Silicones--silicone resin
*Silicones--silicone rubbers
*Styrene-maleic anhydride resins
Styrene polymeric residue
*Styrene-acrylic copolymer resins
*Styrene-acrylonitrile-acrylates copolymers
*Styrene-butadiene resins
*Styrene-butadiene resins (less than 50% butadiene)
*Styrene-butadiene resins (Latex)
*Styrene-divinylbenzene resins (ion exchange)
*Styrene-methacrylate terpolymer resins
*Styrene-methyl methacrylate copolymers
*Styrene-butadiene-vinyl toluene terpolymers
*Sulfonated styrene-maleic anhydride resins
*Unsaturated polyester resins
*Vinyl toluene resins
*Vinyl toluene-acrylate resins
*Vinyl toluene-butadiene resins
*Vinyl toluene-methacrylate resins
*Vinyl acetate-n-butyl acrylate copolymers

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.45 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of the products classified under SIC 28214, thermosetting resins and thermosetting resin groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, listed in this subsection. Product groups are indicated with an asterisk (*).

*Alkyd resins
Dicyanodiamide resin
*Epoxy resins
*Fumaric acid polyesters
*Furan resins
Glyoxal-urea formaldehyde textile resin
*Ketone-formaldehyde resins
*Melamine resins
*Phenolic resins
*Polyacetal resins
*Polyacrylamide
*Polyurethane prepolymers
*Polyurethane resins
*Urea formaldehyde resins
*Urea resins

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.55 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of the products classified under SIC 2865 or 2869, commodity organic chemicals and commodity organic chemical groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, listed in this subsection. Product groups are indicated with an asterisk (*).

1)  Aliphatic Organic Chemicals

Acetaldehyde
Acetic acid
Acetic anhydride
Acetone
Acrylonitrile
Adipic acid
1,3-Butadiene
*Butylenes (Butenes)
Cyclohexane
1,2-Dichloroethane
Ethanol
Ethylene
Ethylene glycol
Ethylene oxide
Formaldehyde
Isopropanol
Methanol
Polyoxypropylene glycol
Propylene
Propylene oxide
Vinyl acetate

2)  Aromatic Organic Chemicals

Benzene
Cumene
Dimethyl terephthalate
Ethylbenzene
Phenol
*Pitch tar residues
Pyrolysis gasolines
Styrene
Terephthalic acid
Toluene
*Xylenes, mixed
o-Xylene
m-Xylene (impure)
p-Xylene

3)  Halogenated Organic Compounds

Vinyl chloride

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.65 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  For discharges of wastewater resulting from the manufacture of butadiene by any process that includes the oxidative dehydrogenation of butene, "new source" means any building, structure, facility, or installation whose construction commenced after December 17, 1973. For other sources, "new source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of the products classified under SIC 2865 or 2869, bulk organic chemicals and bulk organic chemical groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, listed in this subsection. Product groups are indicated with an asterisk (*).

1)  Aliphatic Organic Chemicals

*Acetic acid esters
*Acetic acid salts
Acetone cyanohydrin
Acetylene
Acrylic acid
*Acrylic acid esters
n-alkanes
*Alkylates
Butane (all forms)
1-Butene
1,4-Butanediol
2-Butene (cis and trans)
n-butyl acetate
n-butyl alcohol
sec-butyl alcohol
tert-butyl alcohol
n-butyraldehyde
n-butyric acid
n-butyric anhydride
C4 hydrocarbons (unsaturated)
Calcium stearate
Caprolactam
Carboxymethyl cellulose
Cellulose acetate butyrates
*Cellulose ethers
Cumene hydroperoxide
Cyclohexanol
Cyclohexanol-cyclohexanone (mixed)
Cyclohexanone
Cyclohexene
*C12-C18 primary alcohols (mixed)
*C5 concentrates
*C9 concentrates
Decanol
Diacetone alcohol
*Dicarboxylic acids-salts
Diethyl ether
Diethylene glycol
Diethylene glycol diethyl ether
Diethylene glycol dimethyl ether
Diethylene glycol monoethyl ether
Diethylene glycol monomethyl ether
*Dimer acids
Dioxane
Ethane
2-Ethylbutyraldehyde
Ethylene glycol monophenyl ether
*Ethoxylates, miscellaneous
Ethylene glycol dimethyl ether
Ethylene glycol monobutyl ether
Ethylene glycol monoethyl ether
Ethylene glycol monomethyl ether
2-Ethylhexanol
Glycerine (synthetic)
Glyoxal
Hexane
*Hexane and other C6 hydrocarbons
Isobutanol
Isobutyl acetate
Isobutylene
Isobutyraldehyde
Isophorone
Isophthalic acid
Isoprene
Isopropyl acetate
Ligninsulfonic acid, calcium salt
Maleic anhydride
Methacrylic acid
*Methacrylic acid esters
Methane
Methyl ethyl ketone
Methyl methacrylate
Methyl tert-butyl ether
Methyl isobutyl ketone
Nitrilotriacetic acid
Nylon salt
*alpha-olefins
Oxalic acid
*Oxo-aldehydes-alcohols
*n-parafins
Pentaerythritol
Pentane
1-Pentene
*Pentenes
*Petroleum sulfonates
Pine oil
Polyoxybutylene glycol
Polyoxyethylene glycol
Propane
PropionaldehydePropionic acid
n-propyl acetate
n-propyl alcohol
Propylene glycol
Sodium formate
Sorbitol
Stearic acid, calcium salt (wax)
2,2,4-Trimethyl-1, 3-pentanediol

2)  Amine and Amide Organic Chemicals

*Alkyl amines
Aniline
n-butylamine
sec-butylamine
tert-butylamine
Caprolactam, aqueous concentrate
2,4-Diaminotoluene
Diethanolamine
N,N-diethylaniline
2,6-Dimethylaniline
N,N-dimethylformamide
Diphenylamine
*Ethanolamines
Ethylamine
Ethylenediamine
Ethylenediaminetetraacetic acid
*Fatty amines
Hexamethylenediamine
4-(N-Hydroxyethylethylamino)-2-hydroxyethylaniline
Isopropylamine
Melamine
Melamine crystal
*Methylamines
4,4'-Methylenebis(N,N'-dimethyl) aniline
Methylenedianiline
4,4'-Methylenedianiline
*Nitroanilines
o-Phenylenediamine
1,4-Phenylenediamine dihydrochloride
Polymeric methylene dianiline
Toluenediamine (mixture)
m-Toluidine
*Toluidines

3)  Aromatic Organic Chemicals

*Alkyl benzenes
*Alkyl phenols
*Alkylbenzene sulfonic acids, salts
Aminobenzoic acid (meta and para)
Benzenedisulfonic acid
Benzoic acid
Bis(2-ethylhexyl)phthalate
Bisphenol A
BTX--benzene-toluene-xylene (mixed)
Butyl octyl phthalate
tert-butylphenol
Coal tar
*Coal tar products (miscellaneous)
Creosote
o-Cresol
m-Cresol
p-Cresol
*Cresols, mixed
Cyanuric acid
*Cyclic aromatic sulfonates
Dibutyl phthalate
Diisobutyl phthalate
Diisodecyl phthalate
Diisooctyl phthalate
Dimethyl phthalate
2,4-Dinitrotoluene
2,6-Dinitrotoluene
Dinitrotoluene (mixed)
Ditridecyl phthalate
Metanilic acid
Methylenediphenyldiisocyanate
alpha-methylstyrene
Naphthalene
beta-naphthalene sulfonic acid
*Naphthas, solvent
Nitrobenzene
Nitrotoluene
Nonylphenol
Phthalic acid
Phthalic anhydride
*Tars-pitches
*Toluenediisocyanates (mixture)
Trimellitic acid
1-Tetralol, 1-tetralone mix

4)  Halogenated Organic Chemicals

Allyl chloride
Benzyl chloride
Carbon tetrachloride
*Chlorinated paraffins, 35-44% chlorine
Chlorobenzene
*Chlorobenzenes (mixed)
Chlorodifluoroethane
Chloroform
*Chloromethanes
2-Chloro-5-methylphenol (6-Chloro-m-cresol)
*Chlorophenols
Chloroprene
Cyanogen chloride
Cyanuric chloride
1,1-Dichloroethane
2,4-Dichlorophenol
Dichloropropane
Epichlorohydrin
Ethyl chloride
*Fluorocarbons (Freons)
Methyl chloride
Methylene chloride
Pentachlorophenol
Phosgene
Tetrachloroethylene
1,1,1-Trichloroethane
Trichloroethylene
Trichlorofluoromethane
Vinylidene chloride

5)  Other Organic Chemicals

Adiponitrile
Carbon disulfide
Fatty nitriles
*Organo-tin compounds
*Phosphate esters
Tetraethyl lead
Tetramethyl lead
*Urethane prepolymers
*Waxes, emulsions-dispersions

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.75 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. This Section applies to discharges of process wastewater resulting from the manufacture of any SIC 2865 or 2869 organic chemicals and organic chemical groups, as defined in the Standard Industrial Classification Manual, incorporated by reference in 35 Ill. Adm. Code 310.107, that are not defined as commodity or bulk organic chemicals in Section 307.2405 or 307.2406.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.85 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 414.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after March 21, 1983.

a)  Applicability. The Board incorporates by reference 40 CFR 414.11 (2005). This incorporation includes no later amendments or editions. This Section applies to the discharge of process wastewater resulting from the manufacture of the OCPSF products and product groups defined by 40 CFR 414.11 from any indirect discharge point source.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 414.111 (2005). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources. All sources are treated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of aluminum chloride.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of aluminum sulfate.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.24 (2003). This incorporation includes no later amendments or editions.

2  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of calcium carbide in uncovered furnaces.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of calcium chloride by the brine extraction process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of calcium oxide.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of chlorine and sodium or potassium hydroxide by the diaphragm cell process or by the mercury cell process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of hydrofluoric acid.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of hydrogen peroxide by the electrolytic process or by the oxidation of alkyl hydroanthraquinones.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.91 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of potassium metal.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.116 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of potassium dichromate.

b)  Specialized Definitions. None.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.124 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.126 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of potassium sulfate.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.136 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of sodium bicarbonate.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.146 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of sodium chloride by the solution brine-mining process or by the solar evaporation process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.161 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.166 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of sodium dichromate and by-product sodium sulfate.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.171 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.176 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of sodium sulfite by reacting sulfur dioxide with sodium carbonate.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.201 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.206 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of titanium dioxide by the sulfate process, the chloride process, or the simultaneous beneficiation-chlorination (chloride-ilmenite) process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.221 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.226 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of aluminum fluoride.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.231 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of ammonium chloride by the reaction of anhydrous ammonia with hydrogen chloride gas or by the recovery process from Solvay process wastes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.241 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of borax by the ore mining process or by the Trona process.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of boric acid from ore-mined borax or from borax produced by the Trona process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.281 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of bromine by the brine-mining process or by the Trona process.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.296 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of calcium carbonate by the milk of lime process or by the recovery process from Solvay process wastes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.301 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of calcium hydroxide by the lime slaking process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.311 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.316 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of carbon monoxide and by-product hydrogen by the reforming process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.331 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of chrome pigments.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.341 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.344 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.346 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of chromic acid in facilities that also manufacture sodium dichromate.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.356 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of copper salts, including the following:

1)  Copper sulfate, copper chloride, copper iodide, and copper nitrate; and

2)  Copper carbonate.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.361 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.364 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.366 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of ferric chloride from pickle liquor.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.381 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.384 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.386 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of fluorine by the liquid hydrofluoric acid electrolysis process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.401 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.406 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of hydrogen as a refinery by-product.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.411 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of hydrogen cyanide by the Andrussow process.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.421 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.426 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after July 24, 1980.

a)  Applicability. This Section applies to discharges resulting from the production of iodine.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.431 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.436 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of lead monoxide.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.441 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.444 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.446 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of lithium carbonate by the Trona process or from spodumene ore.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.451 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of nickel salts, including the following:

1)  Nickel sulfate, nickel chloride, nickel nitrate, and nickel fluoborite; and

2)  Nickel carbonate.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 415.471 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 415.474 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 415.476 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after October 25, 1983.

a)  Applicability. This Section applies to discharges resulting from the production of oxygen and nitrogen by air liquification.

b)  Specialized Definitions. None.

c)  Existing Sources. These sources must comply with the general and specific pretreatment requirements of Subpart B.

d)  New Sources. All sources are regulated as existing sources.

a)  Applicability. This Section applies to discharges resulting from the production of potassium chloride by the Trona process or by the mining process.

b)  Specialized Definitions. None.

a)  Applicability. This Section applies to discharges resulting from operations in which neat soap is produced through saponification of animal and vegetable fats and oils by boiling in kettles.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.11 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.14 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.16 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from the splitting of fats to fatty acids by hydrolysis and the subsequent processing of the fatty acids (e.g., refining and hydrogenation) to produce a suitable feed material for the manufacture of soap by fatty acid neutralization.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.21 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.24 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.26 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from the manufacturing of neat soap by neutralizing refined fatty acids with an alkaline material in approximately stoichiometric amounts in batch or continuous operations.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.31 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.34 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.36 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from the concentration of sweet water from saponification or fat splitting to approximately 60 to 80 percent crude glycerine content.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.41 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.44 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.46 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from the production of finished glycerine of various grades (e.g., USP) through concentration from crude glycerine by means of distillation.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.51 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.54 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.56 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from all operations associated with the manufacture of soap flakes and powders, commencing with the drying of the neat soap to and including packaging of the finished flakes and powders.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.61 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.64 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.66 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from all operations associated with the conversion of neat soap to finished bar soaps, including drying, milling, plodding, stamping, and packaging.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.71 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.74 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.76 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.

a)  Applicability. This Section applies to discharges resulting from the blending of ingredients employed in the manufacture of liquid soaps and the packaging of the finished products.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.81 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.84 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

d)  New Sources

1)  The Board incorporates by reference 40 CFR 417.86 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (d)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.

3)  "New source" means any building, structure, facility, or installation whose construction commenced after December 26, 1973.
 
(Source: Amended at 47 Ill. Reg. 4662, effective March 23, 2023)

a)  Applicability. This Section applies to discharges resulting from the manufacture of sulfonic acid and sulfuric acid esters using sulfonation and sulfation of raw materials, including but not limited to petroleum-derived alkyls, employing oleum in either continuous or batch processes.

b)  Specialized Definitions. The Board incorporates by reference 40 CFR 417.91 (2003). This incorporation includes no later amendments or editions.

c)  Existing Sources

1)  The Board incorporates by reference 40 CFR 417.94 (2003). This incorporation includes no later amendments or editions.

2)  No person subject to the pretreatment standards incorporated by reference in subsection (c)(1) may cause, threaten, or allow the discharge of any contaminant to a POTW in violation of those standards.